service article instructions. If no service articles address this concern, INSTALL a new EBB unit (HCU and ABS module assembly). If this is a Ford paid repair, INCLUDE the RVC on the warranty claim form. INSTALL a new BOO switch. ... 4/11/2021 4:27:38 PM ...
service article instructions. If no service articles address this concern, INSTALL a new EBB unit (HCU and ABS module assembly). If this is a Ford paid repair, INCLUDE the RVC on the warranty claim form. INSTALL a new BOO switch. REFER to the Exterior Lighting article. When installing the new switch, USE the appropriate flex probe to VERIFY ...
4/11/2021 Printer Friendly View YMMS: 2020 Ford Ranger Lariat Engine: 2.3L Eng VIN: Apr 11, 2021 License: Odometer: Pinpoint Tests CT: ABS Module DTC C1A99 - Pressure Sensor Normal Operation And Fault Conditions The ABS module uses a pressure sensor located inside the HCU to monitor the integrity of the hydraulic system. When the brake pedal is pressed, the ABS module compares the value of the brake fluid line pressure sensor to the BOO switch input from the PCM over the HS-CAN. If the brake fluid pressure sensor value is not comparable to the BOO switch input, the ABS module sets one or more DTCs. PPT CT ABS MODULE DTC FAULT TRIGGER CONDITIONS DTC Description Fault Trigger Conditions C1A99:01 Pressure Sensor: General Electrical Failure This DTC indicates the brake fluid line hydraulic pressure sensor signal circuit located inside the HCU has failed. Pressure Sensor: Signal Bias Level C1A99:28 Out of Range/Zero Adjustment Failure This DTC indicates the brake fluid line hydraulic pressure sensor located inside the HCU has failed. Possible Causes Incorrectly installed stoplamp switch Brake drag (base brake system concern) Wiring, terminals or connectors HCU CT1: RECHECK FOR ABS MODULE DTC C1A99 Ignition ON, engine OFF. Carry out the ABS self-test. Is DTC C1A99:xx currently present and active in the ABS module? Yes No GATHER information from the customer about conditions necessary to duplicate the concern. Some things to ask the customer may include; how often, drive time, down time, climate conditions (inside and outside the vehicle), speed traveling or maneuvering performed Go to when the fault occurs. CT2. OPERATE the vehicle in the conditions outlined by the customer and MONITOR the PCM BOO1 and BOO2 PIDs, and the ABS module Hydraulic pressure PIDs to determine a focus area. If there is pressure above 1, 379 kPa (200 PSI) and no BOO reading, an incorrectly installed stoplamp switch is the most likely cause. https://www2.prodemand.com/Print/Index?content=article&module=false&tab=false&terms=false&hideOptions= 1/2 4/11/2021 Printer Friendly View CT2: CHECK THE ABS MODULE HYDRAULIC PRESSURE PID NOTE: The brake pressure PID should read close to 0 kPa (0 PSI) with the brake pedal released and increase when applying the brake pedal. Access the ABS and monitor the BRKHYDPRESS (PRESS) PID. While monitoring the PID, fully apply the brake pedal. Does the PID read close to 0 kPa (0 PSI) without the brake pedal applied and increase when the pedal is pressed? Yes Go to CT4. No Go to CT3. CT3: CHECK FOR BRAKE DRAG With the transmission in NEUTRAL, position the vehicle on a hoist. Refer to the Jacking and Lifting article. Spin each wheel by hand and check for any indication of brake drag. Do all 4 wheels spin freely with little to no resistance? Yes No Go to CT4. DIAGNOSE and REPAIR the brake drag concern. REFER to the Brake System General Information article. CT4: CHECK THE PCM BOO1 AND BOO2 PIDS Ignition ON, engine OFF. Monitor the following PIDs while pressing and releasing the brake pedal. Access the PCM and monitor the BOO1 (MODE) PID. Access the PCM and monitor the BOO2 (MODE) PID. Do the PIDs indicate ON with the brake pedal applied and OFF with the brake pedal released? Yes No INSTALL a new EBB assembly. CHECK OASIS for any service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, INSTALL a new BOO switch. DISCONTINUE this test and FOLLOW the REFER to the Exterior Lighting article. service article instructions. When installing the new switch, USE the If no service articles address this concern, appropriate flex probe to VERIFY correct pin INSTALL a new EBB unit (HCU and ABS fitment at the connector. module assembly). If this is a Ford paid repair, INCLUDE the RVC on the warranty claim form. https://www2.prodemand.com/Print/Index?content=article&module=false&tab=false&terms=false&hideOptions= 2/2Mozilla/5.0 (Windows NT 6.1; Win64; x64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/89.0.4389.114 Safari/537.36 Skia/PDF m89