Premium Hot Tubs, Spas, Portable Hot tub, Swim Spas for Sale
LTR20201146, Rev. K 3/22/21 2020 LMS Table of Contents Pre-Delivery Checklist . . . . . . . . . . . . . . . . . 2 Planning the Best Location . . . . . . . . . . . . . 2 Clearance for Service Access . . . . . . . . . . . . 3 Preparing a Good Foundation . . . . . . . . . . . 3 240 Volt Electrical Installation . . . . . . . . . . 3 Bleeding Air from the Pump . . . . . . . . . . . . 12 Operating Your Spa Spa Operation for Pro-trainer - Variable Speed System Only . . . . . . . . . . . . . . . . . . . 13 Settings Screens . . . . . . . . . . . . . . . . . . . . . 15 Error Screens . . . . . . . . . . . . . . . . . . . . . . . 16 Swim Spa Workout Instructions . . . . . . . . 16 Swim Workout Programming . . . . . . . . . . 17 NEO Settings for Cold Climates . . . . . . . . . 18 spaTouch Icon Driven Control Panel . . . . 19 Changing Languages for the Display . . . . . 19 spaTouch3 and spaTouch4 Icon Driven Control Panel . . . . . . . . . . . . . . . . . . . . . . . 29 Cal ConnectTM System . . . . . . . . . . . . . . . . 44 ATS Plus Therapy System . . . . . . . . . . . . . . 54 Electrical Power Efficiency . . . . . . . . . . . . . 55 Jets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 LED Lighting . . . . . . . . . . . . . . . . . . . . . . . . 55 Diverter Knobs . . . . . . . . . . . . . . . . . . . . . . 56 Waterfalls . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Air Venturis . . . . . . . . . . . . . . . . . . . . . . . . . 56 Hydro Streamer Waterfall . . . . . . . . . . . . . 56 Cleaning and Maintenance Removing and Reseating the Pillows . . . . 63 Jet Remove/Replace . . . . . . . . . . . . . . . . . 63 Cleaning the Hydrostreamers . . . . . . . . . . 63 Spa Cover and Locking System Installation . . . . . . . . . . . . . . . . . . . . . . . . . 64 Draining Your Portable Spa . . . . . . . . . . . . 66 Winterizing (Cold Climate Draining) . . . . . 67 Cleaning and Replacing the Filter . . . . . . . 67 Vacation Care . . . . . . . . . . . . . . . . . . . . . . . 67 Cleaning Your Spa . . . . . . . . . . . . . . . . . . . 68 Using the Freedom Sound System . . . . . . . 68 Keeping Fit With Your Swim Spa Air Injection System . . . . . . . . . . . . . . . . . . 69 Swim Tether . . . . . . . . . . . . . . . . . . . . . . . . 69 Exercise Equipment . . . . . . . . . . . . . . . . . . 69 Appendix Replacement Parts . . . . . . . . . . . . . . . . . . . 71 Basic Troubleshooting . . . . . . . . . . . . . . . . 75 "Thermal Creep" . . . . . . . . . . . . . . . . . . . . . 76 Limited Warranty . . . . . . . . . . . . . . . . . . . . 77 Water Clarity The Key to Clear Water . . . . . . . . . . . . . . . 57 Testing and Adjusting Spa Water . . . . . . . 58 Sanitation . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Bather Load . . . . . . . . . . . . . . . . . . . . . . . . . 60 Filter Cleaning . . . . . . . . . . . . . . . . . . . . . . 60 Water Sanitation . . . . . . . . . . . . . . . . . . . . 60 Ozonator . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Maintenance Schedule . . . . . . . . . . . . . . . . 61 Troubleshooting Water Clarity Problems . 62 Copyright 2020 LMS. All rights reserved. Duplication without written consent is strictly prohibited. Cal Spas®, Adjustable Therapy SystemTM, ATSTM, Cal PremiumTM, Cal SelectTM, Cal StoneTM, Pure CureTM, XLTM Heater, and Ultimate Fitness Spa SeriesTM are registered trademarks. Due to continuous improvement programs, all models, operation, and/or specifications are subject to change without prior notice. LTR20201146, Rev. K 3/22/21 CONTACT INFORMATION For customer service, please contact your authorized dealer immediately. If you need additional information and/or assistance, contact: LMS Customer Service Department 1462 East Ninth Street Pomona, CA 91766. Toll Free: 1-800-CAL-SPAS Fax: 1-909-629-3890 Read This First! Important Safety Instructions 1 READ AND FOLLOW ALL INSTRUCTIONS. DANGER -- Risk of accidental drowning: Do not allow children to be in or around a spa unless a responsible adult supervises them. Keep the spa cover on and locked when not in use. See instructions enclosed with your cover for locking procedures. DANGER -- Risk of injury: The suction fittings in this spa are sized to match the specific water flow created by the pump. Should the need arise to replace the suction fittings, or the pump, be sure the flow rates are compatible. Never operate the spa if the suction fitting or filter baskets are broken or missing. Never replace a suction fitting with one that is rated less than the flow rate marked on the original suction fitting. DANGER -- Risk of electric shock: Install the spa at least 5 feet (1.5 meters) from all metal surfaces. As an alternative, a spa may be installed within 5 feet of metal surfaces if each metal surface is permanently bonded by a minimum #8 AWG solid copper conductor to the outside of the spa's control box. Do not permit any external electrical appliances, such as lights, telephones, radios, televisions, and etc., within five feet (1.5 meters) of the spa. Never attempt to operate any electrical device from inside the spa. Replace a damaged power cord immediately. Do not bury the power cord. Connect to a grounded, grounding-type receptacle only. WARNING -- To reduce the risk of injury: The spa water should never exceed 104°F (40°C). Water temperatures between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes. High water temperatures have a high potential for causing fetal damage during pregnancy. Women who are pregnant, or who think they are pregnant, should always check with their physician prior to spa usage. The use of alcohol, drugs or medication before or during spa use may lead to unconsciousness, with the possibility of drowning. Persons suffering from obesity, a medical history of heart disease, low or high blood pressure, circulatory system problems or diabetes should consult a physician before using the spa. Persons using medications should consult a physician before using the spa since some medications may induce drowsiness while others may affect heart rate, blood pressure and circulation. HYPERTHERMIA DANGER: hyperthermia may include: Prolonged exposure to hot air or water can induce · Failure to perceive heat hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level 3°F to 6°F above · Failure to recognize the need to exit spa or hot tub the normal body temperature of 98.6°F (or 2°C to 4°C above · Unawareness of impending hazard 37°C). While hyperthermia has many health benefits, it is important not to allow your body's core temperature to rise · Fetal damage in pregnant women above 103°F (39.5°C). · Physical inability to exit the spa Symptoms of excessive hyperthermia include dizziness, · Unconsciousness lethargy, drowsiness and fainting. The effects of excessive WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. WARNING: People with infectious diseases should not use a spa or hot tub. WARNING: To avoid injury, exercise care when entering or exiting the spa or hot tub. WARNING: Do not use drugs or alcohol before or during 2020 Fitness Spa LTR20201146, Rev. K the use of a spa or hot tub to avoid unconsciousness and possible drowning. WARNING: Do not use a spa or hot tub immediately following strenuous exercise. WARNING: Prolonged immersion in a spa or hot tub may be injurious to your health. CAUTION: Maintain water chemistry in accordance with manufacturer's instructions. www.calspas.com 2 SAVE THESE INSTRUCTIONS. Preparing for Your New Spa Preparing for Your New Spa Pre-Delivery Checklist Most cities and counties require permits for exterior construction and electrical circuits. In addition, some communities have codes requiring residential barriers such as fencing and/or self-closing gates on property to prevent unsupervised access to the property by children. Your dealer can provide information on which permits may be required and how to obtain them prior to the delivery of your spa. Before Delivery Plan your delivery route Choose a suitable location for the spa Lay a 5 - 8 cm concrete slab Install dedicated electrical supply After Delivery Place spa on slab Connect electrical components Planning the Best Location Safety First Do not place your spa within 10 feet (3 m) of overhead power lines. Consider How You Will Use Your Spa How you intend to use your spa will help you determine where you should position it. For example, will you use your spa for recreational or therapeutic purposes? If your spa is mainly used for family recreation, be sure to leave plenty of room around it for activity. If you will use it for relaxation and therapy, you will probably want to create a specific mood around it. Plan for Your Environment If you live in a region where it snows in the winter or rains frequently, place the spa near a house entry. By doing this, you will have a place to change clothes and not be uncomfortable. Consider Your Privacy In a cold-weather climate, bare trees won't provide much privacy. Think of your spa's surroundings during all seasons to determine your best privacy options. Consider the view of your neighbors as well when you plan the location of your spa. Provide a View with Your Spa Think about the direction you will be facing when sitting in your spa. Do you have a special landscaped area in your yard that you find enjoyable? Perhaps there is an area that catches a soothing breeze during the day or a lovely sunset in the evening. Keep Your Spa Clean In planning your spa's location, consider a location where the path to and from the house can be kept clean and free of debris. Prevent dirt and contaminants from being tracked into your spa by placing a foot mat at the spa's entrance where the bathers can clean their feet before entering your spa. Allow for Service Access Make sure the spa is positioned so that access to the equipment compartment and all side panels will not be blocked. Many people choose to install a decorative structure around their spa. If you are installing your spa with any type of structure on the outside, such as a gazebo, remember to allow access for service. It is always best to design special installations so that the spa can still be moved, or lifted off the ground. www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K Clearance for Service Access While you are planning where to locate your spa, you need to determine how much access you will need for service. 3 feet / 1 meter All spa models require a minimum of three feet / one meter access to all sides of the spa for potential service. For this reason, the spa should never be placed in a manner where any side is permanently blocked. Examples include placing the spa against a building, structural posts or columns, or a fence.Spa models require access to all sides in case they need service or repair. See the figure below. If you are planning to enclose or surround your spa with a deck, make sure there is easy access for service or repair. Spas require clearance on all sides of the spa. 3 feet / 1 meter 3 feet / 1 meter 3 feet / 1 meter Preparing a Good Foundation Your spa needs a solid and level foundation. The area that it sits on must be able to support the weight of the spa, with water and the occupants who use it. If the foundation is inadequate, it may shift or settle after the spa is in place, causing stress that could DAMAGE YOUR SPA SHELL AND FINISH. Damage caused by inadequate or improper foundation support is not covered by the warranty. It is the responsibility of the spa owner to provide a proper foundation for the spa. Place the spa on an elevated 3 to 4" / 30 cm concrete slab. Pavers, gravel, brick, sand, timbers or dirt foundations are not adequate to support the spa. We strongly recommend that a qualified, licensed contractor prepare the foundation for your spa. If you are installing the spa indoors, pay close attention to the flooring beneath it. Choose flooring that will not be damaged or stained. If you are installing your spa on an elevated wood deck or other structure, it is highly recommended that you consult a structural engineer or contractor to ensure the structure will supp1o3mfreetettet/r he weight of 150 pounds per square foot (732 kg / m2). To properly identify the weight of your new spa when full, remember water weighs 8.33 lbs. per gallon, or 1 kg per liter. For example, an average 8' spa ho3lfdeest /a1pmpetreroximately 500 gallons, or 1892 liters, of water. Using this formula, you will find that the weight of the water alone is 4,165 lbs, or 1892 kg. Combined with the dry weight of the spa you will note that this spa will weigh approximately 5,000 lbs, or 2267 kg, when full of water. Preparing for Your New Spa 3 3 feet / 1 m 240 Volt Electrical Installation All 240V spas must be permanently connected (hard wired) to the power supply. See the GFCI and wiring requirements starting on page 4. These instructions describe the only acceptable electrical wiring procedure. Spas wired in any other way will void your warranty and may result in serious injury. When installed in the United States, the electrical wiring of this spa must meet the requirements of NEC 70 and any applicable local, state, and federal codes. The electrical circuit must be installed by an electrical contractor and approved by a local building or electrical inspector. Failure to comply with state and local codes may 2020 Fitness Spa LTR20201146, Rev. K result in fire or personal injury and will be the sole responsibility of the spa owner. The power supplied to the spa must be on a dedicated GFCI protected circuit as required by NEC 70 with no other appliances or lights sharing the power. Use copper wire with THHN insulation. Do not use aluminum wire. Use the table below and on the next page to determine your GFCI and wiring requirements. Wires that run over 100 feet must increase wire gauge to the next lower number. For example: A normal 50 amp GFCI with four #6 AWG copper wires that run over 100 feet would require you to go to four #4 AWG copper wires. www.calspas.com Preparing for Your New Spa 4 GFCI and Wiring Requirements Applies to all fitness spas except F-1781 Standard configuration with one 5.5 kW heater Spa Model F-1222 F-1325 F-1421 F-1437 F-1537 F-1641 F-1681 Control System BP501G1 BP501G1 BP501 BP501X BP20X BP20X BP20X GFCI Required One 50 amp GFCI One 50 amp GFCI One 50 amp GFCI One 50 amp GFCI One 60 amp GFCI One 60 amp GFCI One 60 amp GFCI Wires Required Four #6 AWG copper wires Wiring Diagram Use wiring diagram (see page 6) Configuration (auxiliary 5.5 kW heater) Spa Model Control System GFCI Required F-1325, F-1421 BP501X One 50 amp GFCI & one 40 amp GFCI F-1641, F-1681, F-1896 BP20X One 60 amp GFCI & one 40 amp GFCI Wires Required Wiring Diagram Four #6 AWG copper wires Use wiring diagram (see page 5) Four #6 AWG copper wires Use wiring diagram (see page 5) Configuration (Includes F-1781) Spa Model Pro-Trainer System Control System F-1325PT SP2 NEO 2100 F-1681 SP3 NEO 2100 F-1421 SP2 NEO 2100 F-1641 SP3 NEO 2100 F-1781 SP3 NEO 2100 GFCI Required SIEMENS 60 amp breaker SIEMENS 60 amp breaker SIEMENS 60 amp breaker SIEMENS 60 amp breaker SIEMENS 60 amp breaker Wires Required Four #6 AWG copper wires Wiring Diagram Use wiring diagram (see page 6) Applies to model F-1781 only Standard configuration with one 5.5 kW heater except F-1781 Control System BP501G1 Spa Side Service (spa side) GFCI Required Wires Required One 40 amp GFCI Four #8 AWG copper wires Wiring Diagram Use wiring diagram (see page 5) Configuration for Option OPT20-200 (auxiliary 5.5 kW heater) Control System BP20X Spa Side Service 1 (swim side) Service 2 (swim side) GFCI Required Wires Required Wiring Diagram One 60 amp GFCI Four #6 AWG copper wires One 40 amp GFCI Three #8 AWG copper wires Use wiring diagram (see page 6) www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 5 Circuit Board Connection (60 Hz) - NEO US & Canada Preparing for Your New Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 6 Circuit Board Connection (50 Hz) - NEO US & Canada Preparing for Your New Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 7 European Wiring Configuration (NEO) Preparing for Your New Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com Preparing for Your New Spa 8 Wiring Diagram for US & Canada (Balboa) Wiring Diagram for Europe (Balboa) www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K Preparing for Your New Spa 9 Filling and Powering Up Your Portable Spa 1. Inspect the spa equipment. Inspect all plumbing connections in the equipment area of your spa. · Make sure unions in the equipment pack are tight. (Be careful not to over-tighten the plumbing fittings.) · If your spa has gate valves, make sure they are all in the UP or OPEN position. · Make sure the drain valve is closed and capped. (See page 66 for a description of drain valves.) Never run the spa with the gate valves closed or without water circulating for long periods of time. 2. Remove the cartridge from filter canister. If you have a skimmer like this: Grip the filter by the handle and unscrew it from the canister. Never try to pull the filter cartridge while the spa is running in low or high speed (i.e., any speed). If you have a skimmer like this: Remove the black skimmer cap and barrel, grip the filter by the handle and unscrew it from the canister. Teleweir Mega filter skimmer · 75 square feet filtration · Smooth cap If you have a skimmer like this: Rotate and remove the black locking ring. Remove the black skimmer cap and barrel, grip the filter by the handle and unscrew it from the canister. Replace and lock the locking ring and slide the skimmer cap and barrel back in the canister. Note: The skimmer cap and barrel were locked in place at the factory to prevent damage during shipment. It must be unlocked and replaced in the filter canister so that it can float when the spa is filled. If you do not remove the cap and barrel, your spa's filtration system will not perform as it was designed to. Teleweir filter skimmer · 50 square feet filtration · Spoked cap After you remove the filter, remove the plastic wrapper and soak it in water for 30 minutes before you replace it. A dry filter can allow air into the filtration system which can cause the pump to fail to prime. 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com Preparing for Your New Spa 10 3. Fill the spa. Place a garden hose in the filter canister and fill your spa. Always fill the spa through the filter canister. Failure to do so may cause air to be trapped in the filtration system and prevent the pumps from operating properly. Fill the spa until water level is about six inches from the top. If the water level is too low or too high, your spa will not operate properly. Never fill your spa with soft water. Soft water makes it impossible to maintain the proper water chemistry and may cause the water to foam, which will ultimately harm the finish of the spa and void your warranty. You may fill your spa with well water provided the following conditions are met: 1) Purchase and use a pre-filter to run the well water through on the fill-up. The pre-filter will be placed before the spa filter in the fill-up flow of water. 2) Have a Total Dissolved Solids (TDS) and metals test performed by a qualified person after the fill-up process but before any spa use. 4. Turn on power to the spa. When the spa is filled to the correct level, turn on the power at the GFCI breaker. (Ensure that the 120V spas are connected to the proper electrical outlet.) 5. Prime the pump. www.calspas.com For Waterway Systems. The system will enter the priming mode. Priming Mode will display on the control panel. In Priming Mode, all devices such as jets and lights are operable. Jets can be turned on and off to help prime the pump. The system will exit Priming Mode and go to the Main display when the RETURN button is pressed, or after four minutes of activity. 2020 Fitness Spa LTR20201146, Rev. K 11 Priming for Balboa Systems. Preparing for Your New Spa 6. Install the filter into the filter canister. Make sure the filter has soaked at least 30 minutes before you install it. Insert the filter all the way and screw it in. Do not over-torque the cartridge during installation, just hand tighten gently. 7. Adjust water chemistry. Test and adjust the water chemistry. See the section on page 57 for instructions on keeping your water clear. 8. Let the spa heat up. When the spa has finished priming, the heater will activate. Put the cover on and let the spa heat to the set temperature. Priming the Pump New spa owners often have difficulty the first time they start their spa and the pump fails to prime. This can be frustrating, but these simple instructions can help you. Sometimes air can become trapped in the pump while filling the spa. You will know this has happened when after you have filled and started the spa, the pump does not seem to function. You will hear the pump operating, but no water will be moving. Starting Up: Priming Mode for Waterway Systems For Waterway Systems. The system will enter the priming mode. Priming Mode will display on the control panel. In Priming Mode, all devices such as jets and lights are operable. Jets can be turned on and off to help prime the pump. The system will exit Priming Mode and go to the Main display when the RETURN button is pressed, or after four minutes of activity. The pump will not work properly while air is trapped in it. Continuing to operate the pump in this way will cause damage. 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com Preparing for Your New Spa 12 Exiting Priming Mode for Waterway Systems You can manually exit Priming Mode by pressing the RETURN button. Note that if you do not manually exit the priming mode, the priming mode will be automatically terminated after 4 to 5 minutes. Be sure that the pumps have been primed by this time. Starting Up: Priming Mode for Balboa Systems Automatic Exiting of Priming Mode for Balboa Systems Bleeding Air from the Pump If you have tried priming the pump several times unsuccessfully using the control panel, you can bleed the air from the pump manually. 1. Shut off the power to the spa. 2. Using a Phillips screwdriver, remove the front panel from the spa and locate the pump. 3. Close the gate valve on the discharge side of the pump (if your spa is installed with one.) 4. Turn the bleeder valve counter clockwise with a small pair of pliers until the air has been released from the pump. 5. If this is unsuccessful, loosen the union nut on side of the pump with channel locks. When air is bled out, tighten the nut. 6. Turn on power to the spa and press the JETS button. If there is still air trapped in the pump, repeat steps 2 through 5 until the pump primes. www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K Operating Your Spa 13 Spa Operation for Pro-trainer - Variable Speed System Only Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 14 Operating Your Spa F F A F F www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 15 Settings Screens Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com Error Screens 16 Operating Your Spa Swim Spa Workout Instructions www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K Swim Workout Programming 17 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 18 NEO Settings for Cold Climates Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 19 spaTouch Icon Driven Control Panel Operating Your Spa Changing Languages for the Display 1. Touch the Settings Icon at the lower right portion of the screen. 2. Touch the Right Arrow Icon at the lower right portion of the screen. It takes you to the next page. 3. Touch the Language Icon. 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 20 Operating Your Spa 4. As an example, touch the Spanish option as shown below. 5. Next, touch the Save Icon on the right to confirm this selection. 6. ...and now (as an example), the spaTouch screen will be reset to Spanish. www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 21 The Main Screen (Home) Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 22 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 23 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 24 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 25 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 26 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 27 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 28 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K spaTouch3 and spaTouch4 Icon Driven Control Panel 29 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 30 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 31 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 32 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 33 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 34 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 35 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 36 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 37 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 38 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 39 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 40 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 41 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 42 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 43 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 44 Cal ConnectTM System Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 45 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 46 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 47 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 48 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 49 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 50 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 51 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 52 Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 53 Operating Your Spa 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 54 ATS Plus Therapy System Operating Your Spa www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 55 Operating Your Spa Electrical Power Efficiency Your new spa comes equipped with an electric heater. Following the directions listed below will ensure the most efficient operation: NOTE: This method is only for spa usage under two hours a week. · Keep the spa's operating temperature 5°F below the desired usage temperature when not in use. One or two hours before use, set the temperature to the desired temperature. · If the spa usage exceeds two hours a week, the set temperature should remain at the desired usage temperature. · The air venturis should be used sparingly. When open, water temperature drops quite rapidly and can also dissipate chemicals. Allowing the water temperature to lower more than 10°F below the desired usage temperature and reheating it prior to usage will cause the heater to operate longer than it normally would maintaining the desired temperature. Doing this will increase your operating cost and makes your heater work more than necessary. Jets Almost all of the jets in your spa are adjustable. Rotating the face of an adjustable jet to the left (counter-clockwise) will decrease the amount of water flow through the jet. Rotating the face of an adjustable jet to the right (clockwise) will increase the amount of water flow through the jet. (See example shown below.) Neck jets adjust in the opposite directions (counterclockwise to increase, clockwise to decrease). LED Lighting Press the LIGHT button on the topside control panel to turn the spa light on. If your spa has perimeter LED lights, they will also light up at the same time as the spa light. The LEDs operate in three modes: 1. Cycle: When you continually press the LIGHT button, the LEDs will cycle through the three main LED colors (Red, Green, and Blue) or combinations of the three that produce the following colors: light green, purple, light blue, yellow, etc. Each time you press the button, you immediately advance to the next color in sequence or eventually a different light pattern. 2. Flashing: When you are cycling through all the colors, the next time you push the LIGHT button, the LED lights may start flashing. This is another normal operational pattern option. 3. Fading cycle: The next phase of operation when you push the LIGHT button is a slow and/or fast fade random transition from one color to the next. · If a spa is equipped with more than 100 points of light, the Slow Fading Cycle will flicker during a color change. · Every air valve and water valve is equipped with 4 LED points. · Every jet is equipped with 2 LED points. · Perimeter LEDs take 9 points of light. · The waterfall takes 4 points of light. Spas with exterior corner LED lighting generally work in the same mode as described above. The variations in color and patterns provide you with multiple options to suit almost any lighting preference. 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com Operating Your Spa 56 Diverter Knobs Diverter knobs are 1" and 2" knobs located around the top of your spa. They allow you to divert water through jets from one side of the spa to the other, or in most cases from floor jets to wall jets. This is accomplished by rotating the diverter knob to the left (counterclockwise), decreasing the amount of water flow through a section of jets. To increase the amount of water flow through the other section of jets, rotate the handle to the right (clockwise). Waterfalls Some spa series include optional waterfalls. When the booster pump is on, rotate the dial on top (for the cascade waterfall) or turn the knob (for the hydro streamer -- see below). Air Venturis Air venturis are the 1" knobs located around the top of your spa. Each one will let you add a mixture of air with the jet pressure. This is accomplished by rotating the air venturi knob to the left (counterclockwise) to increase the amount of airflow through the jets. To decrease the amount of airflow through the jets, rotate the handle to the right (clockwise). Hydro Streamer Waterfall Your spa may include two to eight streamer waterfalls. When the booster pump is on, turn the 1" diverter knob to adjust the rate of flow to the waterfall jets. The waterfall jet faces are not adjustable. Do not turn the jet faces because you may accidentally remove them. Always shut off water to the hydro streamer jets before you place the cover on the spa. Water from the hydro streamer jets sprays in an arc that is higher than the top surface of the spa. When water from the hydro streamer sprays the bottom of the cover, it will collect and run to the edge of the spa and drip over the top. www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K Water Clarity 57 Water Clarity This section is intended for new spa owners with no experience with water chemistry. Everyone's experience with maintaining water quality is different, but there are some general concepts you need to know. Water maintenance is not difficult, although it requires regular attention. The most important thing to understand about taking care of your spa water is that preventive action is much easier than correcting water quality issues. The Key to Clear Water Excellent water quality is a simple matter of four things: CRhegeumlaircityal Balance SanFiilttraattiioonn YbIvsonaietgulnaademniwtacdmaieuullgqnoautnifintseiasdyecluioditliupeilritsettoaoaslaipdtttieoannlsogutwnteudtaamiutonteseaddrmn.oluaeqAtndualitatjahiummnos,utuqsteuagnttahdhtnieuatt,mmhvceivvlsheoeesllioemseqrteuuinrciei-loatl diniffuict uplrta,tiiet dnioeneudllsutmosabnediodoconneserdegdoulluamrslyan. dit at. Rat, Dceonpseenqudiitningim iolinsi blyaofeuuris ecuhguoeircceilisio. f sanitizer, you nEemevdertitoilitqeusi tentdhiaemlenuvlelulpotaft lcaamlccoiuremminhiabhrdenleestsios,nutmot-al aIsuIlaktnpbadarltiipionsim.ietyrian,eesaencgtdeemnpeHdr.iaaSttioopraearocliwsnogneenraesecwodrittitshodaeclChisseaecldkCdlatuonrtittayl SIanngiteitzaeurgsaitkaillilt ebstaocdtoelruitadioandodlenviairmusqeuast aamndvel keteueep thvseietnadwmiaadmtueqnrut incsilsdecuailipnilie.taaAlaittilnnoogwneutmsuatseanmnituqitzuaeatimrn ,ulseteavntednliut,mwveivlleloslaoeqrleluorii-wl minicruot bperastietodiognruollwumqsuanicdkiolycoinnsetdhdeolsupmasanwdaittaetr..RWat,e reccoonsmeqmuietinndimuilissiinbgla feeuitisheeurgucehrlcoilrisini. e or bromine as yoEmurvesraitniliiqtiuzieern.diam nulluptat lamcore minibh elestio num- Sspaandiopwenraeersesctewmithdiataion erociznogneaatocrortias lsdoelissneededduntto adutdpatsisai.nitizer, although their requirements are dUist sveolluvtewdissaotilsidnosnaulnludt apuhgioamspahuagtaeitslo.re dolore erci te ea consequat. diUffteverel unttw. is atis nonullut augiam augait lore dolore erci te ea consequat. SMeeet ppraatgeeer58sit tdoololer airrinurehetouwer tsoi. bFaeluamnmcey nyuolluamr csopreamwaagntea ra.d dio er SMeeet ppraatge eer5s9it dtoololreiarirunreehtuoewr sti.o uFesuemsmaynnituilzlaemr.core magna ad dio er sequamconum nis eu feugiamet, vent sequamconum nis eu feugiamet, vent et wisis ero dolore dip exeraestie estie et wisis ero dolore dip exeraestie estie vel inisci elisl ut diat, cons aut alit lut lore tin hent adiam iustrud molor l Balance Sanit vel inisci elisl ut diat, cons aut alit lut lore tin hent adiam iustrud molor Chemica arity ation Filtr sustis essit wiscilit wisi. FSailntirtaattioion n CInlgeaent ianuggaiyt oaluitresftioltdeorlurtedgiouldaorlelyinsiamthqueat aemasveiel settue avennddiammqousist edvefuflieepsceetqaiuviaestitinsagimnegdtlueunttetnmhisincqigluialimyt oa, luistenncodanitn-, Your ation Key To CWlReaaetergrul sustis essit wiscilit wisi. ChemRiecagl uBalalarnictey Ing et augait alit esto dolut dio dole- Cnliaemarquwataatmerverl eeqtuueirveensdiaremgquuliasr mduaipinetaenatainngceet. utemEsqtuaabmli,sshendit,a rvoeuletsienqeuisibt aamsedduntonniscilailit arleitgnuolna-r duomstaon kuetaetipn uytoaut rnuwmavtoelrorcelreil ainr.ut sucmhseanduulteatinfourtatynouumr voslpoareriwl inatuetr Acpdaoraulcutislmeoesgatgndhdeioeidtnahutleo.l Rarattue,dmcriorsnataysnneddqifouiplittueincmriomnpwsileitisdloilbwla oferukis heuagrudeercriltishi.an mpraatiinetedniaonnuclel . umsandio consed dolumsandit at. Rat, consequi tinim Mialisini btlaaifneiunisgeugyueoruc rilisi. water quality helps the tEhmevyerniteileiqduiteon,dipamosnsuilblulyptactalaumscinorge mthineibmh etloesftiaoiln.um- sandip eraesectem diatio ercing ea cortis delissed dunt enEjmoyvemriteilniqtuioefndyiaomurnusllpupataat nladmceoxretmenindibsh yeloesutiro nsupma-'s Tuhtpeatisspi. a's heating system will only function with tUhtevelpurtowpiseartisanmonouullunttauogfiamwaautgearit lfolorewdoltohreroeurcgi the etahe lifseandbipy eprareesvecetnemtindgiatidoaemrcainggeeafrcoomrtis ndeeglislseecdt daunntd chuetpmatiicsia. l abuse. scyonssteeqmua.t. SeUcoetnvsepelaquugtawet.is6a1tisfnoornutlhluet asucghiaemdauulgeaitolforeredcoolomremerceintedeead SMeeet ppraatgeeer60sitfodorlofirltieriurreceletuaenr insi.gFienusmtmruycntiuollnams.core magna ad dio er sequamconum nis eu feugiamet, vent et maintenance. Met prate er sit dolor iriureetuer si. Feummy nullamcore wisis ero dolore dip exeraestie estie vel inisci elisl ut diat, cons magna ad dio er sequamconum nis eu feugiamet, vent et aut alit lut lore tin hent adiam iustrud molor sustis essit wis- wisis ero dolore dip exeraestie estie vel inisci elisl ut diat, cons cilit wisi. aut alit lut lore tin hent adiam iustrud molor sustis essit wis- cilit wisi. 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 58 Water Clarity Testing and Adjusting Spa Water You have two types of testing methods to choose from: · The reagent test kit is a method which provides a high level of accuracy. It is available in either liquid or tablet form. · Test strips are a convenient testing method commonly used by spa owners. Balancing the Total Alkalinity Total alkalinity (TA) is the measure of the total levels of carbonates, bicarbonates, hydroxides, and other alkaline substances in the water. TA can be considered a "pH buffer". It is the measure of the ability of the water to resist changes in pH level. The recommended total alkalinity is 80 - 120 ppm. If the TA is too low, the pH level will fluctuate widely from high to low. Low TA can be corrected by adding an alkalinity increaser If the TA is too high, the pH level will tend to be too high and may be difficult to bring down. High TA can be corrected by adding an alkalinity decreaser. When the TA is balanced, it normally remains stable, although adding water with high or low alkalinity will raise or lower the TA level. Balancing the Calcium Hardness Calcium hardness (CH) is a measure of the total amount of dissolved calcium in the water. Calcium helps control the corrosive nature of the spa's water and is why soft water is not recommended. The low calcium content of soft water is very corrosive to the equipment and can cause staining of the spa shell. The recommended calcium hardness is 150 200 ppm. If the CH is too low, add a calcium hardness increaser. If the CH is too high, dilute the spa water with soft water. When the CH is balanced, it normally remains stable, although adding soft water or very hard water will raise or lower the CH level. Balancing the pH The pH level is the measure of the balance between acidity and alkalinity. If the pH is too low, it can cause corrosion of metal fixtures and the heating element. Low pH can be corrected by adding a pH increaser. If the pH is too high, it can cause scaling by allowing metals or minerals to form deposits and stain spa surfaces. High pH can be corrected by adding a pH decreaser. www.calspas.com Ideal Water Chemistry Testing For: Total Alkalinity Calcium Hardness pH Ideal Range (ppm) Minimum Maximum 80 120 150 200 7.2 7.6 2020 Fitness Spa LTR20201146, Rev. K Water Clarity 59 Sanitation Sanitizers kill bacteria and other organic waste by breaking them down to non-harmful levels and are filtered out. Before you fill your spa, you need to decide which chemical sanitizer you wish to use. Consult your Cal Spas dealer for the right decision with regards to your lifestyle and spa usage. We recommend either bromine or chlorine as your sanitizer. Both work well when maintained regularly. DO NOT use trichlor. Trichlor is very acidic and the hot temperature of the spa causes it to dissolve too quickly. It will cause damage to your spa and will void your warranty. Whichever plan you decide on, follow it completely and don't take shortcuts. It will provide you with clean, safe, clear spa water with a minimum of effort. Spa owners with an ozonator still need to use a chemical sanitizer. See page 61 for a description of how the ozonator works. Using Chlorine as a Sanitizer If you choose to use chlorine as a sanitizer, only use granulated chlorine, not liquid chlorine. Once a week, check the chlorine level using either a test strip or a reagent kit. See the table on the following page for the ideal range. Add one or two tablespoons granulated chlorine to the spa water weekly. Note that chlorine dissipation rate will be faster at higher water temperatures and slower at lower temperatures. When you add chlorine, open all of the jets and run the spa at high speed with the cover open for at least 30 minutes. Follow the maintenance schedule on page 61. Using Bromine as a Sanitizer Bromine is a very effective sanitizer that produces low chemical odors. Unlike chlorine, it can break down bacteria and other impurities to a safe level with a low burn-out rate. Use granulated sodium bromide to establish your bromine base. When you begin with fresh water, add two ounces of granulated bromide. Open all of the jets and run the spa at high speed with the cover open for at least 30 minutes. Follow the maintenance schedule on page 61. Shocking the Water In addition to using a chemical sanitizer, you will periodically need to shock the water. Shocking the water helps remove burned-out chemicals, bacteria, and other organic material from your spa's water and improves your sanitizer's effectiveness. Do not use chlorinating shock, which will damage your spa's jets and pump seals. Only use an oxidizer shock. It can be used with either chlorine or bromine sanitizers. Add two ounces of oxidizer shock per 500 gallons once a week, after heavy bather loads, or if water has a strong odor. Spa must be running with all of the jets on high for 30 minutes with the cover open. If necessary, repeat oxidizer shock in 30 minute intervals. . Testing For: Chlorine level Without ozonator Ideal Range (ppm) Minimum Maximum 3.0 5.0 With ozonator 2.0 Bromine level Without ozonator 6.7 4.0 11.0 With ozonator 5.7 10.0 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com Water Clarity 60 Bather Load "Bather Load" is the term used to describe the number of people using a spa, combined with the length of usage, and the frequency of usage. All these factors have a great effect on the spa water. The higher the bather load, the more chemicals need to be added and a longer filtration time will be needed. Recommendations are designed for spas with average bather load (3 to 4 people, 15 minutes of usage, three times a week at 100 degrees) If your bather load exceeds these guidelines, and you experience water quality problems, increase the amount of filtration first, (go to the next higher filtration number) then if water quality is still not adequate, consult the advice of your Cal Spas dealer for additional chemical or system recommendations. Be sure to give them your bather load information. Filter Cleaning The filter is the part of your spa that removes the debris from the water and needs to be cleaned on a regular basis to maximize your spa's filtering performance and heating efficiency. In addition to spraying off the filter weekly to remove surface debris, your filter should be deep cleaned periodically to dissolve scale and particles that get lodged deep within the filter fibers and impede the filtration process. Even if the filter looks clean, scale and particles can clog the fibers and prevent water from flowing through the filter resulting in the most common spa problem--no heat, caused by a dirty filter. We recommend you clean your filter once a month and replace it once a year or as necessary. It is extremely important that you never run the spa without a filter. There is a possibility that debris may be sucked into the plumbing through the filter well. Cleaning the filter 1. Remove the filter by unscrewing it and pulling it up and out. 2. Place the dirty filter into a bucket of water deep enough to cover the filter. Add 8 oz of liquid filter cleaner to the bucket of water. Note: It is a good idea to keep a spare filter to use in the spa while the dirty filter is being deep cleaned. This way, you can rotate the filters and both will last longer. 3. Soak the filter for a minimum of 24 hours. 4. Spray the filter with a water hose. Spray each pleat carefully. 5. Reinstall the filter. Do not overtighten. Water Sanitation The spa's control system is factory-programmed with one filter cycle that will run in the evening when energy rates are often lower. The time and duration of the filter cycle can be set according to your needs. In addition, a second filter cycle can be enabled. Filtration time may need to be increased with heavy bather load. See instructions for setting filtration cycles on page 15. www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 61 Water Clarity Ozonator The ozone generator releases ozone into the spa water. You will still need to test for chlorine or bromine and occasionally replenish it to return the sanitizer level to the baseline. For spas without a circulation pump, pump 1 will run at low speed and the ozonator will run during filtration. For spas with a circulation pump, the ozonator will run with the circulation pump. The spa's control system is factory-programmed with one filter cycle that will run in the evening when energy rates are often lower. The time and duration of the filter cycle can be set according to your needs. In addition, a second filter cycle can be enabled. Filtration time may need to be increased with heavy bather load. See instructions for setting filtration cycles on page 15. Maintenance Schedule Each time you refill the spa Prior to each use Once a week Once a month Every two to four months Once a year Follow the section "Filling and Powering Up Your Portable Spa" on page 9. Test the spa water using either test strips a reagent test kit. Adjust chemical levels as necessary. Test the spa water using either test strips a reagent test kit. Adjust chemical levels as necessary. If your water source is high in calcium, add stain and scale preventer. Deep clean your spa's filter. (Follow filter cleaning instruction at beginning of this section.) Change the spa water. How often you change the water depends on how much you use the spa. When you change the water, you will need to: · Clean and polish the acrylic surface (see page 68) · Clean and treat the spa cover and pillows (see page 68) · Deep clean the filter (see page 60) · Refill your spa (see page 9) Replace filter cartridges if the pleats appear frayed. 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 62 Water Clarity Troubleshooting Water Clarity Problems Problem Cloudy Water Water Odor Chlorine Odor Musty Odor Organic buildup / scum ring around spa Algae Growth Eye Irritation Skin Irritation / Rash Stains Scale Probable Causes Possible Solutions · Dirty filter · Clean filter · Excessive oils / organic matter · Shock spa with sanitizer · Improper sanitization · Add sanitizer · Suspended particles / organic matter · Overused or old water · Adjust pH and/or alkalinity to recommended range · Run jet pump and clean filter · Drain and refill the spa · Excessive organics in water · Shock spa with sanitizer · Improper sanitization · Add sanitizer · Low pH · Adjust pH to recommended range · Chloramine level too high · Shock spa with sanitizer · Low pH · Adjust pH to recommended range · Bacteria or algae growth · Shock spa with sanitizer if problem is visible or persistent, drain, clean and refill the spa · Buildup of oils and dirt · Wipe off scum with clean rag if severe, drain the spa, use a spa surface and tile cleaner to remove the scum and refill the spa · High pH · Shock spa with sanitizer and adjust pH · Low sanitizer level · Shock spa with sanitizer and maintain sanitizer level · Low pH · Adjust pH · Low sanitizer level · Shock spa with sanitizer and maintain sanitizer level · Unsanitary water · Shock spa with sanitizer and maintain sanitizer · Free chlorine level above 5 ppm level · Allow free chlorine level to drop below 5 ppm before spa use · Total alkalinity and/or pH too low · High iron or copper in source water · Adjust total alkalinity and/or pH · Use a stain and scale inhibitor · High calcium content in water · Adjust total alkalinity and pH if scale requires total alkalinity and pH too high removal, drain the spa, scrub off the scale, refill the spa and balance the water · Use a stain and scale inhibitor www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K Cleaning and Maintenance Removing and Reseating the Pillows You can remove the pillows for cleaning and maintenance quickly and easily. This method works for all types of pillows. Grab the lower edge of the pillow with both hands firmly and pull up. As you do this, the pillow inserts will pop out of the holes. Reseat the pillows by aligning the pillow inserts with the holes and striking the pillow hard enough to insert the pegs back into the holes. Jet Remove/Replace Jets can be easily removed for cleaning. Grasp the outer rim of the jet and turn it counter-clockwise. The jet will unscrew from the fitting until it is free. To replace the jet, place it in the fitting and turn it clockwise until it is snug in place. Do not overtighten the jet. Cleaning the Hydrostreamers To ensure proper flow through the hydrostreamers, follow this maintenance process should any jet(s) have diminished flow. 1. Turn the jet counter-clockwide to remove the chrome jet head. 2. Pull the chrome cap off. 3. Pull the plastic jet opening and its gasket off. 2020 Fitness Spa LTR20201146, Rev. K 63 www.calspas.com Cleaning and Maintenance 64 4. Pull out the inner plastic filter. 5. The plastic filter is shown completely removed from its housing. Cleaning and Maintenance 6. Tap the filter and/or blow out the debris to ensure all holes are clear. 7. Slide the plastic filter back in the jet. 8. Re-insert the gasket into clear plastic spout. 9. Place the gasket into the plastic spout and then insert the spout into the jet body. 10. Insert the plastic spout into the jet body. 11. Place the chrome ring cap back on and turn clockwise to tighten it down. Spa Cover and Locking System Installation Important! Keep the spa covered when not in use! · Covered spas will use less electricity in maintaining your set temperature. · Covering your spa will protect your spa's finish from the sun's ultraviolet rays. · You are required to keep the spa covered to maintain warranty coverage. · Covering your spa helps prevent children from drowning in the spa. In addition, while the spa cover is rigid, it is not designed to support any weight. Therefore, as a safety precaution and to preserve the life of your cover, you must not sit, stand, or lie on it, nor should you place objects of any kind on top of it. www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K Cleaning and Maintenance Step 1 - Place cover on spa. Make sure it is correctly positioned. 65 Step 2 - Position the tie-down hardware (attached to the straps of your cover) on the side of the spa so they are easily reached by the cover tie-down straps. Step 3 - With the straps pulled taut (but not overly tight), lightly drill the location for screw placement. Gently drill 3 holes - one for each screw slot in the lock. (If you do not have a low torque drill, use the lowest torque setting on the drill you have.) DO NOT drill all the way in but instead just make a guide for starters. Step 4 - Use a screwdriver to finish screwing in the 3 screws. (Repeat this process for the other 3 corners.) Step 5 - Keep the cover fastened down at all times when not in use. Locking hardware may be locked with a key (which is provided). 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com Cleaning and Maintenance 66 Step 6 - The provided key will allow you to lock down spa access. Draining Your Portable Spa Your spa should be drained every four to six months for cleaning and maintenance and refilled with fresh tap water. See page 68 for instructions on cleaning the shell, cover, and pillows. See page 9 for instructions on refilling your spa. Before you begin, turn off power to the spa at the breaker and remove all filters. 1. Locate your drain. All fitness spas have a cabinet mounted drain The location of the cabinet mounted drain is shown in the left photo by the arrow. (It is located to the right of the fitness spa's "door.") Pull the knob out of the cabinet. The cabinet drain is screwed into the drain pull knob. 2. Remove the cap Make sure the valve is in the closed position, then unscrew and remove the cap. www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K Cleaning and Maintenance 3. Connect valve to a garden hose. For all spas 67 Attach a garden hose to the hose-bib fixture. Place the other end of the garden hose where you would like the water to drain. 4. Drain the spa. Turn the valve on the hose-bib fixture to open the drain. When the spa has drained completely, turn the valve on the hose-bib fixture, remove garden hose, and replace the cap. Winterizing (Cold Climate Draining) In many areas of the country, the temperature drops below 32°F (0°C). We recommend that you always have your spa full of water and running at normal spa temperatures (80°F to 100°F, 26.7°C to 37.8°C). This will help reduce the risk of freezing in your spa and your spa's equipment. Warning: If you find the need to drain your spa, be aware of the potential of freezing in your spas equipment and plumbing. Even if the directions below are followed perfectly, there is no guarantee that your spa will not suffer freeze damage. Freeze damage is not covered by your warranty. 1. Open all filter covers. 2. Remove the filter baskets and filters. 3. Drain your spa completely as described in the instructions above. 4. Vacuum water from the spa's main drain fitting with a wet/dry vacuum. 5. Open the bleeder valves on the pumps. 6. Disconnect the unions from both sides of the pump. 7. Blow any remaining water out of the jets and equipment area with the wet/dry vacuum. 8. When it has completely finished draining, close the bleeder valves and re-connect the unions on the pumps. Replace the filter baskets and filters. 9. Cover your spa with a good spa cover and an allweather tarp to ensure that neither rain nor snow enters the spa. Cleaning and Replacing the Filter Filtration is one of the most important steps you can take to ensure clean, clear water. It is far less expensive to fix water clarity problems by filtering your spa than by using excessive amounts of chemicals, excessive filtration times, or by water replacement. See the section "Filter Cleaning" on page 60 for more information. Vacation Care You can leave your spa unattended for up to two weeks if you follow these instructions. ALWAYS lock your cover using the cover locks if you plan to be away from home and the spa is filled with water. 1. Select the Low Range temp choice used for vacation mode. (See instructions on page 14 for vacation setting.) 2. Following the water quality instructions starting on page 57, adjust the pH. 3. Shock the water (add either chlorine or bromine sanitizer). 4. When you return, check and adjust the pH and shock the water. If you will not be using your spa for longer than 14 days and a spa maintenance service is not available, we strongly recommend you drain or winterize your spa. 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com Cleaning and Maintenance 68 Cleaning Your Spa Spa Cover and Pillows Due to the constant punishment your spa cover and pillows receive, you should protect them by applying a vinyl and leather cleaner as part of your monthly maintenance plan. Use a product that is specifically designed to protect spa covers and pillows from chemical and ultraviolet light damage without leaving an oily residue behind that is normally associated with common automotive vinyl protectants. W arning: Do not use automotive vinyl protectants on spa covers or pillows. These products are generally oil-based and will cause severe water clarity issues that are difficult to correct. Spa Shell Each time you drain your spa, before you refill it you should clean your spa shell with an all-purpose cleaner and apply a coat of surface protectant. Use a low detergent, non-abrasive cleaner specifically formulated to clean the spa without damaging its acrylic finish. Use a non-oil based surface protectant that is specifically formulated to protect the spa's finish from the chemicals and minerals associated with normal spa use. Using the Freedom Sound System The Freedom Sound SystemTM entertainment option contains a Bluetooth-enabled speaker system that is available for certain Cal Spa models. Any Bluetooth-enabled device can be used to play audio through your spa. Before you can use the sound system, you need to pair the Bluetooth module with your device. The Bluetooth module is installed within the spa cabinet. Everything can be done with your device. The example shown below is from an iPhone device. Your device may appear differently. Before you begin, make sure Bluetooth in enabled on your device. 1. Select Bluetooth from your device's option list. 2. Select SWA8-6BT... from the list of available devices to pair. 3. Your iPhone device will ask for a code: the code is 0000. 4. Allow your device to pair with the spa's Bluetooth module. 5. When the devices have been connected, the device SWA8-6BT... will be highlighted. Only one Bluetooth device can be paired with the Freedom Sound SystemTM at any time. (For Android users, the systems will pair automatically - no code is needed.) Once your device is paired and connected, all sounds from your device will be played through the sound system, including system sounds and telephone. 1 2 3 4 www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K Keeping Fit With Your Swim Spa 69 Keeping Fit With Your Swim Spa Air Injection System Use the control panel to start and stop the Air Injection System. The JET 1 and JET 2 buttons control the top and bottom jets. Use the air venturi valves to inject air in the water streams for even more power. Swim Tether The swim tether pole has three pieces and assembles easily. Slide the ends of the top and middle sections into the middle and bottom sections. Insert the tether in the anchor hole when you are ready to use it. Buckle the strap around your waist. It is easily adjustable and can accommodate most sizes. Exercise Equipment IMPORTANT: Always consult your physician before starting any exercise activity or program. The Ultimate Fitness series spas feature rubber exercise bands. When stretched, these bands create a high tension condition. Improper use or failure to connect the exercise bands properly may cause injury. Always inspect all of the exercise equipment prior to beginning any exercise. Do not use any damaged equipment. This equipment attaches to the exercise anchors located on the spa walls. Connecting the Exercise Equipment The drawings below show different ways the exercise kit can be connected depending on the exercises you wish to do. 2020 Fitness Spa LTR20201146, Rev. K For 14 foot spas and model F-1222 The exercise kit contains: · Two hand grips · Two ankle braces · Two 6" elastic bands · Two 18" elastic bands · Two 25" elastic bands · Two rowing bars For 16 and 17 foot spas The exercise kit contains: · Two hand grips · Two ankle braces · Two 18" elastic bands · Two 25" elastic bands · Two 56" elastic bands · Two rowing bars www.calspas.com Keeping Fit With Your Swim Spa 70 When attaching the rowing bar, place the hook into the eye pad as shown. Elastic bands6a"ttabcahnds with to the eye pad ahsand grips shown. Typic1a8l "cboannfdiguration for F-1222 spa 25" bands 56" bands with hand grips 18" band Elastic bands attach to the eye pad as shown. 18" band 25" bands All elastic bands can be connected to the end of the s5p6a" baanndds used with either hand grips or ankle braces. All elastic bands can be connected to All elastic bands can be connected to Alleeitlhaesrteicndbaonf tdhsecsapna aanlsdoubseeduwsiethdhwanitdh the end of either hand the grips sopraanaknledburasceeds.2w5it"h bands eitghreiprshoar nadnkgleribprascoers.ankle braces. All elastic bands can also be used with Typical configuration for 16' and 17' spa When attaching the rowing bar, place the hook into the eye pad as shown. either hand grips or ankle braces. 6" bands with hand grips 18" band 56" bands with hand grips All elastic bands can be connected to the end of the spa and used with either hand grips or ankle braces. Typical configuration for 12', 13', 14' spa When attaching the rowing bar, place the All elastic bands can also be used with 18" either hand grips or ankl6e"brbaacensd. s with band hook into thEelaesytiec pbaadnds attach hand grips as shown. to the eye pad as shown. 25" bands 56" bands with hand grips Elastic with ha 25" bands 18" band Elastic bands attach to the eye pad as shown. 18" band 25" bands All elastic bands can be connected to the end of the spa and used with either hand grips or ankle braces. All elastic bands can also be used with either hand grips or ankle braces. www.calspas.com All elastic bands can be connected to the end of the spa and used with either hand grips or ankle braces. 25" bands 18" band 25" bands 18" band 2020 Fitness Spa LTR20201146, Rev. K Please visit www.quickspaparts.com to order your replacement parts. 71 Appendix Appendix Replacement Parts Jets Inserts - Screw-in ELE 2" Euro No Eyeball PLUCS2295021SL Jets Inserts - Screw-in PSD 5" Power Storm PLUCS2295131SL MED 3" XL Cluster Storm Directional PLUCS2295031SL mfd 3" Micro Flow Directional PLUCS2295061SL MM 3" Mini Storm Massage PLUCS2297061SL-8 PSR 5" Power Storm Riffed PLUCS2295141SL PST 5" Power Storm Wagon Wheel PLUCS2295191SL MFD 3.5" Maxi Flow Directional PLUCS2295091SL River Jet Assembly Black with Stainless Steel Rim 210-5101SCS PLU210-5101SCS 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com Appendix 72 Jets Inserts - Screw-in Power Stream Swim Jet PLU210-0821S Pillows Y Pillow recess ACC01401101 Jets Inserts - Snap-in SQR SQN candy cane, 2" neck jet, 100% shut-off Candy cane w/clear center PLU29923-144-000 Infinity Pillow Plain Black ACC01401061 Water Diverter Valves Diverter Valve 2" Black/Titanium Waterfall Flush Mount Water Feature Assembly (Clear) PLU210-9288S PLU21300465 Diverter Valve 1" Black/Titanium PLU21300453 Diverter Valve 1½" On/Off ASSY (600-4601) PLU21100045 Pillows Air Control Valve Air Control Black/Titanium Cascade Pillow No Insert Black ACC01401031 Drains Drain Super Hi Flo Suction 2½" Black (640-3581LGV) PLU21400146 www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K Drains Low Profile Drain ¾" Black (640-0511) PLU21400401 Teleweir Skimmer Teleweir filter skimmer 50 sq. ft. (510-4601) FIL11700006 Filter 50 sq ft female threaded antibacterial (for Teleweir skimmer shown above) FIL11100208 LED Lights 1-LED light string LIT16100330 2-LED light string LIT16100331 2020 Fitness Spa LTR20201146, Rev. K Please visit www.quickspaparts.com to order your replacement parts. 73 LED Lights Appendix 4-LED light string LIT16100332 1 to 3 ext. cord LIT16100335 1 to 1 port ext. cord LIT16100338 Interior light with logic (7 LED) LIT16100333 Interior light without logic (7 LED) LIT16100337 Main light housing, LED lens, fitting nut LIT16100336 www.calspas.com Please visit www.quickspaparts.com 74 to order your replacement parts. Appendix Exercise Equipment Exercise Kit for 12 Foot and 14 Foot Spas EXC12000008 Exercise Kit for 16 Foot and 17 Foot Spas EXC12000007 Exercise Kit Attachment Plate EXC11000065 Cover Lock and Keys ACC01800026 www.calspas.com Replacement Cabinet Panels The complete selection of replacement cabinets for all models is very extensive and too lengthy for this owner's manual. To order replacement panels for your spa, visit www.quickspaparts.com. Covers All spa covers are designed with a tapered height, angling downward from the center to the sides to drive off rain and prevent water from pooling. The covers listed below are filled with either 1 lb, 1.5 lb, or 2.0 lb foam. Deluxe 5" - 3" 2.0 Lb. foam 93" x 141" Fits spa models: F-1222 COV93141DBK-3 Deluxe Taper Black COV93141DDB-3 Deluxe Taper Dark Brown COV93141DG-3 Deluxe Taper Gray 93" x 171" Fits spa models: F-1420, F-1437 COV93171DBK-3 Deluxe Taper Black COV93171DDB-3 Deluxe Taper Dark Brown COV93171DG-3 Deluxe Taper Gray 93" x 200" Fits spa models: F-1640, F-1770 COV93200DBK-3 Deluxe Taper Black COV93200DDB-3 Deluxe Taper Dark Brown COV93200DG-3 Deluxe Taper Gray 93" x 210" Fits spa model F-1896DL COV93210DBK-3 Deluxe Taper Black COV93210DDB-3 Deluxe Taper Dark Brown COV93210DG-3 Deluxe Taper Gray 93" x 151" Fits spa model F-1335 COV93151DBK-3 Deluxe Taper Black COV93151DDB-3 Deluxe Taper Dark Brown COV93151DG-3 Deluxe Taper Gray 2020 Fitness Spa LTR20201146, Rev. K Appendix 75 Basic Troubleshooting The troubleshooting guidance provided here is intended to cover the most common problems a spa owner may encounter. For more in-depth troubleshooting, go to www.calspas.com/troubleshooting. Symptom Problems starting up Pump won't prime Breaker keeps shutting off Power and system problems System won't start up or breaker keeps shutting off Control panel doesn't respond Spa does not turn off Message on the control panel Heat problems Spa water does not get hot Spa overheats - temperature greater than 110°F / 43°C Water pressure problems Low water pressure Possible Solutions See priming instructions on pages 10 and 11. Reset the GFCI breaker. If this continues, contact your dealer or a qualified spa technician. Power may be shut off. Turn on GFCI circuit breaker. If this continues, contact your dealer or a qualified spa technician. Turn on or reset the GFCI circuit breaker. If this does not solve the problem, contact your dealer or a qualified spa technician. If you hear the pump running but the control panel doesn't respond, contact your dealer. Spa may be trying to heat up. In cold climates, if spa is not equipped with full foam or any kind of insulation, it will try to maintain the set temperature. Set the spa to low temperature range and set the temperature to 80°F. Spa may be in filter cycle. If it is, this is normal and no adjustment is necessary. There may be a problem. See Error Screens on page 16. Spa may be in low temperature range. Set the spa to high temperature range. The filter may be dirty or may need to be replaced. Clean or replace the filter. The water level may be too low. Fill the spa with water level at 4 to 6 inches from the top. The temperature is not turned up high enough. Raise temperature on topside control. Cover the spa. The cover will keep heat in the spa and help keep heat from escaping. Make sure cover is on at all times when spa is not in use. The heater element may be old, deteriorated, coated with scale, or defective. Contact your dealer for more assistance. The gate valves may be partially or completely closed. NEVER OPERATE YOUR SPA WITH THE GATE VALVES CLOSED! Overheating can occur during summer months and may not necessarily indicate a malfunction. When it occurs, a message code may also appear on the control panel. Temperature may be set too high. Turn the set temperature down to a lower temperature. Filtration time may be too long. Turn the filtration cycles down during the warm months. The spa may not be properly ventilated. Make sure the front of the spa is not blocked to allow air flow. High speed pumps may have been running too long. Limit pump running time to no more than 15 to 30 minutes. Jet valves may be partially or fully closed. Open the jet valves. Filter cartridge may be dirty. Clean or replace the filter. Pump may have airlock. Remove airlock by priming spa (pages 10 and 11). The suction fittings may be blocked. Remove any debris that may be blocking them. The filter skimmer may be blocked. Remove the blockage. Gate valves may be closed. Open gate valves. Note: Never operate your spa with the gate valves closed! 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 76 Please visit www.quickspaparts.com to order your replacement parts. Appendix Symptom No water pressure (no water stream from any jets) Jets surge on and off Possible Solutions Power may be switched off. Turn the power back on. The pump may be defective. After you have tried all other troubleshooting, contact your dealer for assistance. Water level may be too low. Add water to normal level. Pump problems Pump runs constantly will not shut off Noisy pump Pump turns off during operation Pump has a burning smell while running Pump does not run "Thermal Creep" There may be a problem with circuit board. Contact your dealer. The water level may be too low. Fill the spa with water level at 4 to 6 inches from the top. Filter cartridge may be dirty. Clean or replace the filter. Pump may have airlock. Remove airlock by priming spa (pages 10 and 11). The suction fittings may be blocked. Remove any debris that may be blocking the suction fittings. Gate valves may be closed. Open gate valves. Note: Never operate your spa with the gate valves closed! Air may be leaking into the suction line. Contact your dealer for assistance. Debris may be inside the pump. Contact your dealer for assistance. Noise may be a sign of damage. Contact your dealer for service. Automatic timer may have completed its cycle. Press JET 1 or JET 2 button to start the cycle again. Pump may have overheated due to the vents on the equipment door being blocked. Make sure the front of the spa is not blocked to allow air flow. The pump motor may be defective. Contact your dealer for assistance. A burning smell may be a sign of damage. Contact your dealer for service. Pump may have over heated. Let it cool for an hour and try operating the spa for a shorter time. Power to the spa may be shut off. Turn on or reset the GFCI circuit breaker. If this does not solve the problem, contact your dealer or a qualified spa technician. Cal Spas are designed with energy-efficient components and systems that are meant to sustain heat generated by the equipment, which is then cycled back into the spa water. In hot weather or in situations where the spa is set to extended run times, Thermal Creep may occur. Thermal Creep is a condition where the measured water temperature can be higher than the set temperature. To manage Thermal Creep you may: Vent your cover. This means placing a folded cloth about ¾" (2cm) thick under all four corners of the cover before you lock the cover down. Open your cover. Opening the cover at night will also quickly cool the water down if desired. Open all air controls. Set your filtration cycles to run during the cooler times of the day or night. Reduce the length of your filter cycles. Visit your local dealer for additional guidance. Since Thermal Creep only occurs in well-insulated hot tubs, it is not indicative of something that is wrong with your spa or its equipment. www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 77 Appendix Limited Warranty This Limited Warranty is extended to the original purchaser of a Cal Spa brand portable spa manufactured after January 1, 2020 and installed for residential use in the United States of America and Canada. This warranty begins on the date of delivery of the spa, but in no event later than one year from the date of manufacture. Shell Structural Warranted against water loss due to defects in the spa shell. Shell Finish Warranted against blistering, cracking, or delaminating of the interior surface of the spa shell. Equipment and Controls Electrical equipment components specifically limited to the pumps, standard titanium heater, and control system are warranted against malfunctions due to defects in workmanship or materials. Plumbing Warranted against leaks due to defects in workmanship or materials. Cabinet - synthetic or fiberglass Warranted against defects in workmanship or materials. Normal wear and weathering of the finish will occur naturally over time and are not defects. 10 years 7 years 5 years 5 years 5 years Warranties for Other Components The fuses, headrests, cabinet finish, and filters are warranted to be free of defects in workmanship and material at the time of delivery. The factory installed water purification system is warranted against malfunction due to defects in workmanship or material for one year from the original date of delivery. All stereo-related components (receiver, speakers, sub-woofer, stereo media locker, power supply, wireless remote control etc.) are warranted against malfunction due to defects in workmanship or material for one year from the original date of delivery. All other factory-installed components not mentioned specifically, including, but not limited to the wood frame, jets, diverter valves, LED lighting systems, filter lids, and mechanical components, are warranted against malfunction due to defects in workmanship and material for two years from the original date of delivery. The insulating spa cover delivered with the fitness spa is warranted to be free from defects in workmanship and material for one year. Genuine Cal Spas Parts & Accessories This Limited Warranty is void if Cal Spas (the "Manufacturer") or its designated representative determines that the spa has been subjected to damage or failure due to installation of aftermarket parts that are not genuine Cal Spas branded parts and accessories. This disclaimer includes, but is not limited to filters, ozone systems, salt systems, repair parts and other accessories. Genuine Cal Spas brand parts and accessories are built to our highest standards of quality, durability and performance, and they are designed to work with your spa to ensure optimal performance and function. Performance This warranty begins on the date of delivery of the spa, but in no event later than one year from the date of manufacture. To obtain service in the event of a defect covered by this Limited Warranty, notify your Cal Spa dealer or Cal Spas as soon as possible and use all reasonable means to protect the spa from further damage. Upon proof of purchase, a designated service representative will correct the defect subject to the terms and conditions contained in this Limited Warranty. There will be no charge for parts or labor to repair the defect, although providing access to affect the repair is your responsibility as the spa owner. Freight charges for replacement parts is the responsibility of the spa owner. You may be assessed reasonable repairman travel mileage charges. In the event that the spa is removed to a repair facility for repair and reinstalled, the cost of removal and reinstallation will be your responsibility as the spa owner. If the Manufacturer determines that repair of the 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com Appendix 78 covered defect is not feasible, it reserves the right to provide a replacement spa of equal value to the original purchase price. In such an event, reasonable costs for removal of the original spa, shipping costs from the factory for the replacement spa and delivery and installation of the replacement will be your responsibility as the spa owner. The replacement spa will carry the balance of the original spa's warranty. Spa covers are not included. This warranty ends either by specified time frame, owner-transfer, relocation, or installation of any component other than by manufacturer. Warranty Limitations This Limited Warranty is void if Cal Spas or its designated representative determines that the spa has been subjected to alteration, neglect, misuse or abuse, or freight damage caused by the common carrier; any repairs have been attempted by anyone other than a designated representative; the failure is caused by accident, acts of God or other causes beyond the control of the Manufacturer; neglect, misuse and abuse include any installation, operation or maintenance of the spa other than in accordance with the instructions contained in the owner's manual provided with the spa, including but not limited to the failure to maintain proper water chemistry and chemical balance and the use of abrasive or improper cleaners or non-genuine parts and accessories. This Limited Warranty does not provide coverage for any item attached to or installed on the spa after the date of manufacture or for gaining access to any component for repair or replacement. Spa units in commercial use are excluded from any coverage whatsoever. The spa owner accepts liability for repair work performed by anyone other than the Manufacturer or a designated Cal Spa representative. This Limited Warranty is void if damage occurs to the spa shell because of excessive heat buildup due to failure to cover a spa that is empty of water while exposed to direct sunlight. Proration of Warranty Units determined by the Company to be non-repairable will be replaced on a prorated basis with the same or a comparable unit. The user will be charged one percent of the current retail cost for each full month of ownership from the date of purchase through the date failure is determined to be non-repairable. This charge will be waived during the first twelve months of ownership. Limitations The Manufacturer disclaims all warranties, expressed or implied, in fact or in law, to the extent allowed by your State's Law, including the warranty of merchantability and fitness for use, except as stated specifically herein. All warranty service must be performed by the Manufacturer or its designated representative using authorized Cal Spa parts. No agent, dealer, distributor, service company or other party is authorized to change, modify or extend the terms of this limited warranty in any manner whatsoever. The Manufacturer will not be responsible for any statements or representations made in any form that go beyond, are broader than, or are inconsistent with any authorized literature or specifications furnished by Cal Spas. Disclaimers The Manufacturer and its representatives shall not be liable for any injury, loss, cost or other damage, whether incidental or consequential, arising out of any defect covered by this limited warranty, including without limitation, loss of use of the spa and cost for removal of defective product even if the Manufacturer was advised of the possibility of damage. The liability of the Manufacturer under this limited warranty, if any, shall not exceed the original amount paid for the defective product. Coverage under this limited warranty shall commence as of the original date of delivery and the duration of such coverage shall not extend for any reason whatsoever beyond the stated time periods. These disclaimers shall be equally applicable to any service provided by the Manufacturer and its designated representatives. Legal Rights This Limited Warranty gives you specific legal rights. You may also have other rights that vary from state to state. Some states do not allow limitations on how long an implied warranty lasts, so this limitation may not apply to you. www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 79 Appendix 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com 80 Appendix www.calspas.com 2020 Fitness Spa LTR20201146, Rev. K 81 Appendix 2020 Fitness Spa LTR20201146, Rev. K www.calspas.com Locating the product serial number The serial number of your spa is located on a metal plate attached to the inside of the door for the equipment area. You will need this number to properly register your spa and activate coverage. Write this information in the space provided below. Spa Model: ____________________________________________________________________________ Spa Serial Number: _____________________________________________________________________ Date Purchased: _______________________________________________________________________ Date Installed: _________________________________________________________________________ Dealer's Phone Number: _________________________________________________________________ Dealer's Address: _______________________________________________________________________ It is important that you register your Cal Spas product as soon as possible. By taking just a few quick minutes to register, you can enjoy product alerts, more efficient support, and quicker service. Go to https://calspas.com/register-your-spa.php. Fill in your information and click "SEND WARRANTY INFO" Please write a review to let us know how you feel about your spa. To post your review, go to www.calspas.com. LTR20201146, Rev. K 3/22/21Adobe PDF Library 15.0