P65Warnings.ca.govUser Manual for CHAMPION models including: Semi Trash Pump, 100743
Read this operator's manual before operating your water pump. Familiarize yourself with the location and function of the controls and features. Save this manual ...
2020-07-22 — READ AND SAVE ThiS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product. Failure to.
OPERATOR'S MANUAL MODEL #100743 3 IN. (7.5 CM) SEMI-TRASH PUMP REGISTER YOUR PRODUCT ONLINE at championpowerequipment.com or visit championpowerequipment.com READ AND SAVE THIS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product. Failure to do so could result in serious injury. This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice. Made in China - REV 20200520 Champion Power Equipment, Inc., Santa Fe Springs, CA USA 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP TABLE OF CONTENTS Introduction................................................... 3 Safety Definitions .......................................... 3 Important Safety Instructions ....................... 4 Fuel Safety ......................................................... 6 Safety and Dataplate Labels....................................... 7 Safety Symbols..................................................... 8 Operation Symbols ............................................... 10 Quickstart Label Symbols........................................ 10 Controls and Features ................................. 11 Parts Included .................................................... 12 Assembly ..................................................... 13 Remove the Water Pump from the Shipping Carton ............ 13 Install Handle, Wheels, and Support Legs ...................... 13 Add Engine Oil.................................................... 13 Add Fuel .......................................................... 14 Operation ..................................................... 15 Water Pump Location ............................................ 15 Connecting a Hose Kit ........................................... 16 Priming the Pump ................................................ 20 Before Starting the Engine....................................... 21 Starting the Engine............................................... 21 Stopping the Engine.............................................. 22 Operation at High Altitude ....................................... 22 Maintenance ................................................ 23 Cleaning the Water Pump ........................................ 23 Changing the Engine Oil ......................................... 23 Cleaning and Adjusting the Spark Plug(s) ....................... 24 Cleaning the Air Filter ............................................ 24 Cleaning the Spark Arrestor ..................................... 24 Adjusting the Governor........................................... 25 Maintenance Schedule........................................... 25 TABLE OF CONTENTS Storage ........................................................ 25 Water Pump Storage ................................... .......... 25 Short Term Engine Storage (Up to 30 Days) .................... 25 Mid Term Engine Storage ( 30 Days 1 year) ........ .......... 25 Long Term Storage..................................... .......... 26 Specifications.............................................. 27 Water Pump Specifications ...................................... 27 Engine Specifications ............................................ 27 Engine Oil Specifications............................... .......... 27 Fuel Specifications ............................................... 27 Spark Plug Specifications........................................ 27 Valve Specifications.................................... .......... 27 Important Message About Temperature............... .......... 27 Parts Diagram - Frame and Engine ................... .......... 28 Parts List ......................................................... 29 Engine Parts Diagram............................................ 31 Engine Parts List ....................................... .......... 32 Troubleshooting........................................... 34 2 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP INTRODUCTION Congratulations on your purchase of a Champion Power Equipment (CPE) product. CPE designs, builds, and supports all of our products to strict specifications and guidelines. With proper product knowledge, safe use, and regular maintenance, this product should bring years of satisfying service. Every effort has been made to ensure the accuracy and completeness of the information in this manual at the time of publication, and we reserve the right to change, alter and/or improve the product and this document at any time without prior notice. Since CPE highly values how our products are designed, manufactured, operated and are serviced, and also highly value your safety and the safety of others, we would like you to take the time to review this product manual and other product materials thoroughly and be fully aware and knowledgeable of the assembly, operation, dangers and maintenance of the product before use. Fully familiarize yourself, and make sure others who plan on operating the product fully familiarize themselves too, with the proper safety and operation procedures before each use. Please always exercise common sense and always err on the side of caution when operating the product to ensure no accident, property damage, or injury occurs. We want you to continue to use and be satisfied with your CPE product for years to come. When contacting CPE about parts and/or service, you will need to supply the complete model and serial numbers of your product. Transcribe the information found on your product's nameplate label to the table below CPE TECHNICAL SUPPORT TEAM 1-877-338-0999 MODEL NUMBER 100743 SERIAL NUMBER INTRODUCTION SAFETY DEFINITIONS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE NOTICE indicates information considered important, but not hazard-related (e.g., messages relating to property damaged). DATE OF PURCHASE PURCHASE LOCATION 3 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP IMPORTANT SAFETY INSTRUCTIONS WARNING Cancer and Reproductive Harm www.P65Warnings.ca.gov DANGER Water pump engine exhaust contains carbon monoxide, a colorless, odorless, poison gas. Breathing carbon monoxide will cause nausea, dizziness, fainting or death. If you start to feel dizzy or weak, get to fresh air immediately. OPERATE THE WATER PUMP OUTDOORS ONLY IN A WELL VENTILATED AREA AND POINT EXHAUST AWAY. DO NOT operate the water pump inside any building, including garages, basements, crawlspaces and sheds, enclosure or compartment, including the storage compartment of a recreational vehicle. DO NOT allow exhaust fumes to enter a confined area through windows, doors, vents or other openings. DANGER Using an engine indoors CAN KILL YOU IN MINUTES. Engine exhaust contains carbon monoxide. This is a poison you cannot see or smell. NEVER use inside a home or garage, EVEN IF doors and windows are open. ONLY use OUTSIDE and far away from windows, doors, and vents. Install battery-operated carbon monoxide alarms or plug-in carbon monoxide alarms with battery back-up according to the manufacturer's instructions. IMPORTANT SAFETY INSTRUCTIONS DANGER Rotating parts can entangle hands, feet, hair, clothing and/or accessories. Traumatic amputation or severe laceration can result. Keep hands and feet away from rotating parts. Tie up long hair and remove jewelry. Operate equipment with guards in place. DO NOT wear loose-fitting clothing, dangling drawstrings or items that could become caught. WARNING Spark from removed spark plug wire can result in fire or electrical shock. When servicing the water pump: Disconnect the spark plug wire and place it where it cannot contact the plug or any other metal object. DO NOT check for spark with the plug removed. Use only approved spark plug testers. WARNING Contact with electrical power source can cause electric shock or burn. NEVER spray in the direction of or near a power source/ electrical outlet. WARNING Running engines produce heat. Severe burns can occur on contact. Combustible material can catch fire on contact. DO NOT touch hot surfaces. Avoid contact with hot exhaust gases. Allow equipment to cool before touching. Maintain at least 3 ft. (91.4 cm) of clearance on all sides to ensure adequate cooling. Maintain at least 5 ft. (1.5 m) of clearance from combustible materials. DANGER DO NOT pump gasoline, fuel, fuel-oil mixtures, detergents, acids, chemicals, beverages, pesticides, fertilizers or any other flammable liquid or corrosive. 4 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP WARNING DO NOT immerse the water pump in water. DANGER The water pump develops powerful force. DO NOT move the water pump when it is in use. DO NOT use hoses or connectors that are worn, damaged or frayed. DO NOT allow children or unqualified persons to operate or service the water pump. DO NOT open top plug or drain plug. WARNING Rapid retraction of the starter cord will pull hand and arm towards the engine faster than you can let go. Unintentional startup can result in entanglement, traumatic amputation or laceration. Broken bones, fractures, bruises or sprains could result. When starting engine, pull the starter cord slowly until resistance is felt and then pull rapidly to avoid kickback. WARNING DO NOT pump salt, sludge, sewer, sea, or any other type of water containing solid material. CAUTION Exceeding the pump specification for total head can damage the pump and/or hose kits connected to it. DO NOT modify the pump in any way. DO NOT attempt to exceed the rated flow. Attempting to increase the rated flow may damage the unit and/or shorten its life. NOTICE DO NOT run the pump dry. Running the pump dry can destroy the pump seals and will void the warranty. If the pump was running while dry, stop the engine and allow it to cool thoroughly before filling the chamber with water. IMPORTANT SAFETY INSTRUCTIONS CAUTION Improper treatment or use of the water pump can damage it, shorten its life and void your warranty. Use the water pump only for intended uses. Operate only on level surfaces. DO NOT expose water pump to excessive moisture, dust, or dirt. DO NOT allow any material to block the cooling slots. DO NOT use the engine if: Equipment sparks, smokes or emits flames Equipment vibrates excessively WARNING Use of this water pump can create wet, slippery walking surfaces. Use only on a level surface. Make sure there is proper drainage to dissipate water. 5 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP Fuel Safety DANGER GASOLINE AND GASOLINE VAPORS ARE HIGHLY FLAMMABLE AND EXPLOSIVE. Fire or explosion can cause severe burns or death. Gasoline and gasoline vapors: Gasoline is highly flammable and explosive. Gasoline can cause a fire or explosion if ignited. Gasoline is a liquid fuel but its vapors can ignite. Gasoline is a skin irritant and needs to be cleaned up immediately if spilled on skin or clothes. Gasoline has a distinctive odor, this will help detect potential leaks quickly. In any petroleum gas fire, flames should not be extinguished unless by doing so the fuel supply valve can be turned OFF. This is because if a fire is extinguished and a supply of fuel is not turned OFF, then an explosion hazard could be created. Gasoline expands or contracts with ambient temperatures. Never fill the gasoline tank to full capacity, as gasoline needs room to expand if temperatures rise. When adding or removing gasoline: DO NOT light or smoke cigarettes. Turn the engine off and let it cool for at least two minutes before removing the gasoline cap. Loosen the cap slowly to relieve pressure in the tank. Only fill or drain gasoline outdoors in a well-ventilated area. DO NOT pump gasoline directly into the engine at the gas station. Use an approved container to transfer the fuel to the engine. DO NOT overfill the gasoline tank. Always keep gasoline away from sparks, open flames, pilot lights, heat and other sources of ignition. When starting the engine: DO NOT attempt to start a damaged engine. Make certain that the gasoline cap, air filter, spark plug, fuel lines and exhaust system are properly in place. Allow spilled gasoline to evaporate fully before attempting to start the engine. Make certain that the water pump is resting firmly on level ground. When operating the water pump: DO NOT move or tip the water pump during operation. DO NOT tip the water pump or allow fuel or oil to spill. IMPORTANT SAFETY INSTRUCTIONS When transporting or servicing the water pump: Make certain that the fuel valve is in the OFF position, the gasoline tank is empty. Disconnect the spark plug wire. When storing the water pump: Store away from sparks, open flames, pilot lights, heat and other sources of ignition. Do not store water pump or gasoline near furnaces, water heaters, or any other appliances that produce heat or have automatic ignitions. WARNING NEVER use a gasoline container, gasoline tank, or any other fuel item that is broken, cut, torn or damaged. 6 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP IMPORTANT SAFETY INSTRUCTIONS Safety and Dataplate Labels These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement. A B D C Side Side LABEL DANGER PELIGRO DANGER A 2012-L-OP-A DESCRIPTION Safety Symbols/ CO Danger 2011-L-OP-A B C D 2 UNLEADED FUEL ONLY. Minimum octane rating of 87. Maximum 10% ethanol. GASOLINA REGULAR SOLAMENTE. 87 octanos como mínimo. Máximo de etanol de 10%. ESSENCE SANS PLOMB SEULEMENT. Indice d'octane minimal de 87. Maximum 10 % d'éthanol. WARNING ADVERTENCIA AVERTISSEMENT DO NOT TOUCH! Operation of this equipment may create sparks that can start Exhaust gases, muffler fires around dry vegetation. A spark arrestor may be and engine components required. The operator should contact local fire agencies for are extremely HOT and laws and regulations relating to fire prevention requirements. cause burns. If installed, clean every 100 hours or every season. ¡NO TOCAR! Los gases de La operación de este equipo puede producir chispas que pueden provocar escape, el silenciador y los incendios alrededor de la vegetación seca. Un supresor de chispas puede que compnonentes del motor están sea necesario. El operador debe comunicarse con las agencias locales de extremadamente CALIENTES y bomberos para las leyes y reglamentos relativos a los requisitos de prevención causan quemaduras. de incendios. Si está instalado, limpie cada 100 horas o cada temporada. NE PAS TOUCHER! Les gaz Cet équipement peut créer des étincelles et provoquer un incendie dans la d'échappement, le silencieux végétation sèche. Un pare-étincelles peut être requis. L'utilisateur doit et les pièces du moteur sont communiquer avec le service d'incendie local pour connaître les lois et extrêmement CHAUDS et les règlements en matière de prévention des incendies. Si elle est peuvent causer des brûlures. installée, nettoyez la génératrice toutes les 100 heures ou chaque saison. CHAMPION POWER EQUIPMENT, INC. 12039 SMITH AVENUE SANTA FE SPRINGS, CA 90670 USA / É.-U. 1-877-338-0999 WWW.CHAMPIONPOWEREQUIPMENT.COM MADE IN CHINA / FABRIQUÉ EN CHINE 2216-L-PR-A MODEL MODÈLE 100743 INLET DIAMETER DIAMÈTRE D'ENTRÉE FLOW (GPM / LPM) DÉBIT (GPM / LPM) 3 IN. 7.5 CM 264 / 1000 MANUFACTURE DATE DATE DE FABRICATION XXXX SERIAL NO. / N° DE SÉRIE XXXXXXXXXXXX 1035-L-SF-C Fuel Hot Surface Dataplate 7 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP IMPORTANT SAFETY INSTRUCTIONS Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product. SYMBOL MEANING Read Operator's Manual. To reduce the risk of injury, user must read and understand operator's manual before using this product. Eye and Ear Protection. Always wear safety goggles or safety glasses with side shields, and as necessary a full face-shield as well as full ear protection when operating this product. Footwear. Always wear safety shoes or heavy boots when operating the machine. Gloves. Always wear nonslip, heavy-duty protective gloves when operating this product. Safety Alert. Precautions that involve your safety. Risk of Fire. Fuel and its vapors are extremely flammable and explosive. Fire can cause severe burns or death. Do not add fuel while the product is operating or still hot. Hot Surface. To reduce the risk of injury or damage, avoid contact with any hot surface Open Flame alert. Fuel and its vapors are extremely flammable and explosive. Keep fuel away from smoking, open flames, sparks, pilot lights, heat, and other ignition sources. 8 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP IMPORTANT SAFETY INSTRUCTIONS SYMBOL MEANING Toxic Fumes. The engine exhaust from this product contains chemicals known to the state of California to cause cancer and birth defects and other reproductive harm. Risk of Asphyxiation. This engine emits carbon monoxide, an odorless, colorless poison gas. Breathing carbon monoxide can cause nausea, fainting or death. Use only in a well ventilated area. Clearance. Keep all objects including others at least 10 feet (3m) from this machine. Only one person should operate the water pump and load the logs 9 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP IMPORTANT SAFETY INSTRUCTIONS Operation Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product. SYMBOL MEANING Choke. Pull choke knob to "CHOKE" position. Run. Push choke knob to "RUN" position. Fuel/Gasoline Valve On/Off SYMBOL MEANING On Stop or Off Throttle Lever - Fast Fuel Gauge: Full Throttle Lever - Slow Fuel Gauge: Empty Quickstart Label Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product. 1 2 3 10W-30 8 9 10 4 11 5 6 7 1 2 3 4 2174-L-OP-A Starting the Engine DANGER Move water pump outside and far away from windows, doors and intake ventilation covers. 1. Check oil level. Recommended oil is 10W-30. 2. Check fuel level. 3. Connect inlet and outlet hoses 4. Connect inlet filter 5. Prime the water pump 6. Move the fuel valve to the "ON" position. 7. Move the choke lever to the "CHOKE" position by pulling out. 8. Move throttle to "FAST" position. 9. Press engine switch to "ON" position. 10. Pull the starter cord slowly until resistance is felt and then pull rapidly. 11. As engine warms up, move the choke to "RUN" by pushing in and adjust the throttle as needed Stopping 1. Move the fuel valve to the "OFF" position. 2. Press the engine switch to the "OFF" position. 3. Disconnect inlet and outlet hoses for storage. 4. Remove drain plug (bottom) before storage. 10 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP CONTROLS AND FEATURES CONTROLS AND FEATURES Read this operator's manual before operating your water pump. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. 21 14 19 18 3 4 5 6 13 12 8 9 10 11 7 17 16 15 1. Gasoline Tank Cap 2. Gasoline Tank 3. Air Filter 4. Support Leg 5. Transport Handle 6. Throttle 7. Fuel Valve 8. Recoil Handle 9. Oil Drain Bolt (on each side) 10. Engine Oil Fill Cap/Dipstick 11. Wheels 12. Engine Switch 13. Choke 14. Fuel Gauge 15. Drain Plug (bottom) 16. Inlet 17. Muffler 18. Outlet 19. Priming Cap (top) 11 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP Parts Included Assembly Parts Part Wheels Support Leg Discharge hose (blue) Suction hose (green) Accessory Bag Engine oil funnel Teflon® tape Parts Not Included Engine Oil (10W-30) Part Qty. Hardware Needed Wheel cap 2 R-clip Roll pin Ø16×96 Bolt M6×40 2 Flange lock nut M6 Outlet hose adapter Outlet hose fitting 1 Gasket Silver colored hose clamp 3" 74-79 mm 1 Cam lock coupler (2 parts, coupler and fitting) Filter (2 parts) 1 Gold colored hose clamp 3" 80-85 mm 1 1 1 Hardware Qty. 2 2 2 4 4 1 1 1 1 1 1 3 N/A N/A N/A CONTROLS AND FEATURES Tool Needed N/A 1× 8mm wrench or socket 1× 10mm wrench or socket N/A 1× 13mm wrench or socket N/A 1× 13mm wrench or socket 12 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP ASSEMBLY Your water pump requires some assembly. This unit ships from the factory without oil. It must be properly serviced with fuel and oil before operation. For questions regarding the assembly of your water pump, call our help line at 1-877-338-0999. Please have your serial number and model number available. Remove the Water Pump from the Shipping Carton 1. Set the shipping carton on a solid, flat surface. 2. Remove all contents from the carton except the water pump. 3. Carefully cut each corner of the box from top to bottom. Install Handle, Wheels, and Support Legs Wheels 1. Before adding fuel and oil, carefully pivot the water pump up and forward so that it rests engine side down. Place a piece of cardboard from the packaging or moving blanket on the ground before tipping forward. 2. Slide the roll pin through the wheel from the outside. 3. Slide the roll pin through the mount point on the frame. 4. Secure with the R-clip. 5. Repeat to attach the second wheel. 6. Add wheel caps to protect the roll pins. ASSEMBLY Support Legs 1. Attach the supports legs to the water pump frame with (2) M6 × 40 flange bolts and (2) M6 flange lock nuts per leg. Tighten to 7.4±1.5 lbf-ft (10±2 Nm). 2. Repeat to attach the second leg. 3. Slowly tip the water pump back down so that it rests on the support legs. Add Engine Oil CAUTION DO NOT attempt to crank or start the engine before it has been properly filled with the recommended type and amount of oil. Damage to the engine as a result of failure to follow these instructions will void your warranty. NOTICE The engine rotor has a sealed, pre-lubricated ball bearing that requires no additional lubrication for the life of the bearing. NOTICE The recommended oil type is 10W-30 automotive oil. 1. Place the water pump on a flat, level surface. 2. Remove oil fill cap/dipstick to add oil. 3. Using a funnel, add up to 16.9 fl. oz (500 ml) of oil and replace oil fill cap/dipstick. DO NOT OVERFILL. 13 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP 4. Check engine oil level before every use and add as needed. MAX OIL DIP STICK ASSEMBLY NOTICE Synthetic oil may be used after the 5 hour initial break-in period. Using synthetic oil does not decrease the recommended oil change interval. Full synthetic 5W-30 oil will aid in starting in cold ambient < 41º F (5º C). Recommended Engine Oil Type 10W-30 5W-30 10W-40 5W-30 Synthetic °F -20 0 20 40 60 80 100 120 °C -28.9 -17.8 -6.7 4.4 15.6 26.7 37.8 48.9 Ambient temperature NOTICE Weather will affect engine oil and engine performance. Change the type of engine oil used based on weather conditions to suit the engine needs. NOTICE Once oil has been added, a visual check should show oil about 1-2 threads from running out of the fill hole. If using the dipstick to check oil level, DO NOT screw in the dipstick while checking. NOTICE Check oil often during the break-in period. Refer to the Maintenance section for recommended service intervals. CAUTION The engine is equipped with a low oil shut-off and will stop when the oil level in the crankcase falls below the threshold level. NOTICE The first 5 hours of run time is the break-in period for the engine. During the break in period, it is recommended to use standard automotive, non-synthetic blended oils. After the break-in period, synthetic oil can be used but is not required. Adjusting throttle setting will increase/ decrease engine speed helping to seat piston rings. Avoid bogging or lugging the engine down and avoid prolonged running at constant RPM. After the 5-hour break-in period, change the oil. Add Fuel Use clean, fresh, regular unleaded gasoline with a minimum octane rating of 87 and an ethanol content of less than 10% by volume. y b c DO NOT mix oil with gasoline. 1. Place the water pump on a flat, level surface. 2. Remove the gasoline cap. 3. Slowly add gasoline to the tank. DO NOT OVERFILL. Gasoline can expand after filling. A minimum of ¼ in. (6.4 mm) of space left in the tank is required for gasoline expansion, although more than ¼ in. (6.4 mm) is recommended. Gasoline can be forced out of the tank as a result of expansion if overfilled, and can affect the stable running condition of the water pump. The approximate fuel level is shown on the fuel gauge on top of the fuel tank. 14 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP EMPTY FULL 4. Screw on the gasoline cap and wipe away any spilled fuel. CAUTION Use regular unleaded gasoline with a minimum octane rating of 87 and an ethanol content of less than 10% by volume. DO NOT light cigarettes or smoke when filling the tank. DO NOT mix oil and gasoline. Fill tank to approximately ¼ in. (6.4 mm) below the top of the tank to allow for gasoline expansion. DO NOT pump gasoline directly into the water pump at the pump. Use an approved container to transfer the gasoline to the water pump. DO NOT fill tank indoors. DO NOT fill tank when the engine is running or hot. DO NOT overfill the tank. WARNING Pouring gasoline too fast through the fuel screen may result in blow back of gasoline at the operator while filling. OPERATION NOTICE Our engines work well with 10% or less ethanol blend gasoline. When using ethanol-gasoline blends there are some issues worth noting: Ethanol-gasoline blends can absorb more water than gasoline alone. These blends can eventually separate, leaving water or a watery goo in the tank, fuel valve and carburetor. With gravity-fed supplies, the compromised gasoline can be drawn into the carburetor and cause damage to the engine and/or potential hazards. There are only a few suppliers of fuel stabilizer that are formulated to work with ethanol-gasoline blends. Any damages or hazards caused by using improper gasoline, improperly stored gasoline, and/or improperly formulated stabilizers, are not covered by manufacturer's warranty. It is advisable to always shut off the gasoline supply, run the engine to starvation and drain the tank when the equipment is not in use for more than 30 days. OPERATION Water Pump Location DANGER Water pump engine exhaust contains carbon monoxide, a colorless, odorless, poison gas. Breathing carbon monoxide will cause nausea, dizziness, fainting or death. If you start to feel dizzy or weak, get to fresh air immediately. OPERATE THE WATER PUMP OUTDOORS ONLY IN A WELL VENTILATED AREA AND POINT EXHAUST AWAY. DO NOT operate the water pump inside any building, including garages, basements, crawlspaces and sheds, enclosure or compartment, including the storage compartment of a recreational vehicle. DO NOT allow exhaust fumes to enter a confined area through windows, doors, vents or other openings. 15 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP DANGER Using an engine indoors CAN KILL YOU IN MINUTES. Engine exhaust contains carbon monoxide. This is a poison you cannot see or smell. NEVER use inside a home or garage, EVEN IF doors and windows are open. ONLY use OUTSIDE and far away from windows, doors, and vents. Total Head Suction Head OPERATION Discharge Head Install battery-operated carbon monoxide alarms or plug-in carbon monoxide alarms with battery back-up according to the manufacturer's instructions. WARNING Running engines produce heat. Severe burns can occur on contact. Combustible material can catch fire on contact. DO NOT touch hot surfaces. Avoid contact with hot exhaust gases. Allow equipment to cool before touching. Maintain at least 3 ft. (91.4 cm) of clearance on all sides to ensure adequate cooling. Maintain at least 5 ft. (1.5 m) of clearance from combustible materials. Place the water pump on a flat, level surface. The pump should be placed close to the water level to ensure maximum pump performance. Pump output will be affected by the type, length, and size of the suction and discharge hoses. The pumping height, also known as the total head, is the distance from the water level to the point of discharge. As this distance increases, pump output decreases. The discharge capacity is greater than the suction capacity. Therefore, it is important that the suction head is less than the discharge head. The time required to draw water from the source to the pump (self-priming time) can be decreased by minimizing the suction head. Connecting a Hose Kit NOTICE Both the inlet and outlet ports are 3 in. (7.5 cm) NPT. Please ensure the connectors to the suction and discharge hose are 3 in. (7.5 cm) NPT threaded. Connect the Discharge Hose (Blue) 1. Locate (1) of the following: outlet hose adapter (C), gasket (A), and outlet hose fitting (B) and align for assembly. A B C 2. Thread the assembled connector to the outlet fitting (top of pump). Locate the blue "outlet" label on the pump. NOTICE Make sure the gasket is seated inside before threading the adapter on. 16 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP 3. Locate and slide the silver colored hose clamp (marked 7479) over the blue outlet hose. OPERATION 5. Slide the hose clamp in place about midway on the outlet hose adapter as shown. Tighten to 7.4±1.5 lbf-ft (10±2 Nm) with a 13mm wrench. The hose clamp should be placed behind the outlet adapter barbs on the smooth part of the adapter. 4. Slide the blue discharge hose over the outlet hose fitting. NOTICE You may use a small amount of dish soap on the outlet hose fitting to help ease the outlet hose on the fitting. Work the soap around the fitting with your finger. Then work the blue hose on the outlet, by twisting and turning until it's fully seated. Connect the Suction Hose (Green) and Suction Filter 1. Locate the following: cam lock coupler (coupler and fitting together) (A), 80-85 marked hose clamps (B), Teflon® tape (C), green suction hose (D) and align for assembly. A B D C 2. Cut ties and uncoil the green hose and use some weight to help straighten the hose out. Best to do this on a warmer day in the sun. 17 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP 3. Separate the cam lock coupler and fitting. Align the green hose to the coupler and mark the locations of the ribs on the fitting. OPERATION 7. Insert the threaded or quick coupler in the green rigid suction hose until properly seated. 4. Mark the second rib on the coupler on the hose. NOTICE You may use a small amount of dish soap on the cam lock coupler to help ease the green hose on the fitting. Work the soap around the coupler with your finger. Then work the green hose on the fitting, by twisting and turning until it's fully seated. 8. Slide the clamps marked 80-85 over cam lock coupler just past the marks you made on the hose earlier. 5. Lay the green hose side by side and place the clamp marked 80-85 in their approximate location. 9. Rotate and align the clamp bolts so you have clearance for the cam levers to lock in place later. 6. Slide the clamps back and start to assemble the green hose to cam lock coupler. 18 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP 10. Tighten each clamp to 7.4±1.5 lbf-ft (10±2 Nm) with a 13mm wrench. If you do not have a torque wrench, hand tight then ¼ turn past full tight. 14. Attach the cam lock coupler to the fitting. OPERATION 11. Test connection is tight by twisting coupler in the hose to make sure it doesn't turn. If coupling turns, then tighten clamps further until coupling won't turn. 15. Lock in place with the cam levers. 12. Wrap the green inlet clockwise with the Teflon® tape provided with 4 complete wraps. NOTICE If the cam levers do not clamp down completely, rotate and align the clamp bolts so you have clearance for the cam levers to lock. See step 9 earlier. 16. Locate the following: filter (E) and 80-85 marked hose clamp (F). E F 13. Thread the fitting over the tape and hand tighten. If you have channel locks large enough, you can give it a ¼ turn past hand tight. 17. Snap the filter pieces together. 19 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP 18. Place the clamp marked 80-85 on the other end of the green hose. Attach the strainer to the green suction hose. 21. You should have everything connected. OPERATION NOTICE You may use a small amount of dish soap on the filter to help ease the green hose on the filter. Work the soap around the filter with your finger. Then work the green hose on the filter, by twisting and turning until it's fully seated. 19. Slide the clamp just before the end of the green hose. 20. Tighten the clamp to 7.4±1.5 lbf-ft (10±2 Nm) with a 13mm wrench. If you do not have a torque wrench, hand tight then ¼ turn past full tight. Priming the Pump NOTICE DO NOT run the pump dry. Running the pump dry can destroy the pump seals and will void the warranty. If the pump was running while dry, stop the engine and allow it to cool thoroughly before filling the chamber with water. NOTICE Ensure the priming plug is secure before pump operation, if not secure the priming plug could be ejected and water or other liquids could be pumped through the top of the outlet flange. 1. Remove the priming cap (top) and fill pump body to the very top of outlet flange with water. Reinstall the priming plug. DO NOT over tighten. 2. As the engine starts up, this will start the draw of liquid into the pump. Located within the pump assembly is the oneway valve. As you prime the pump housing this one-way flap valve shuts off the opening to the suction hose. The priming process is only required when the pump housing is not full of water. 20 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP Before Starting the Engine 1. Route the suction hose so that the filter is immersed completely in the water supply source. 2. DO NOT operate pump without the filter fully immersed. 3. DO NOT operate the pump without the filter attached to the hose. 4. Secure the suction hose to keep it from moving once the water pump is started. 5. Route the discharge hose to the desired location. Secure the discharge hose to keep it from moving once the water pump is started. 6. Place the water pump on a flat, level surface. 7. Check that the oil is at the full mark on the dipstick, and that fuel has been added to the fuel tank. 8. Review the water pump assembly and ensure fittings are properly secured and make sure there are no kinks, cuts, or damage to hoses. Starting the Engine NOTICE DO NOT run the pump without the unit primed and suction hose in the water. Damage to equipment resulting from failure to follow this instruction will void warranty. 1. Make certain the water pump is on a flat, level surface. 2. Move the fuel valve to the ON position OPERATION NOTICE Keep choke lever in "CHOKE" position for 2 pulls of the recoil starter. After second pull, move choke lever to the "RUN" position for up to the next 3 pulls of the recoil starter. Too much choke leads to spark plug fouling/engine flooding due to the lack of incoming air. This will cause the engine not to start. NOTICE If the engine starts but does not run make certain that the unit is on a flat, level surface. The engine is equipped with a low oil sensor that will prevent the engine from running when the oil level falls below a critical threshold. 4. Move the throttle lever to the "FAST" position. 5. Press engine switch to "ON" position. 3. Move the choke lever to the "CHOKE" position by pulling out. 6. Pull the starter cord slowly until resistance is felt and then pull rapidly. 21 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP WARNING Rapid retraction of the recoil cord will pull hand and arm towards the engine faster than you can let go. Unintentional startup can result in entanglement, traumatic amputation or laceration. Broken bones, fractures, bruises or sprains could result. 7. As engine warms up, move the choke to "RUN" by pushing in and adjust the throttle as needed OPERATION 2. Let the engine run until fuel starvation has stopped the engine. This usually takes a few minutes. 3. Press the engine switch to the "OFF" position. NOTICE Water pump performance can be adjusted using the throttle. To decrease pump output, slide the throttle to the slow the engine speed, towards "SLOW". To increase it, slide the throttle towards "FAST" WARNING DO NOT remove either top cap or bottom plug while the water pump is on and running. Loss of pressure and suction will occur. Injury may also occur. Stopping the Engine NOTICE If the engine will not be used for a period of two (2) weeks or longer, please see the Storage section for proper engine and fuel storage. 1. Turn the fuel valve to the "OFF" position. Important: Always ensure that the fuel valve and the engine switch are in the "OFF" position when the engine is not in use. Operation at High Altitude The density of air at high altitude is lower than at sea level. Engine power is reduced as the air mass and air-fuel ratio decrease. Engine power and water pump output will be reduced approximately 3½% for every 1000 ft. of elevation above sea level. This is a natural trend and cannot be changed by adjusting the engine. At high altitudes increased exhaust emissions can also result due to the increased enrichment of the air fuel ratio. Other high altitude issues can include hard starting, increased fuel consumption and spark plug fouling. To alleviate high altitude issues other than the natural power loss, CPE can provide a high altitude carburetor main jet. The alternative main jet and installation instructions can be obtained by contacting our Technical Support Team. Installation instructions are also available in the Technical Bulletin area of the CPE website. The part number and recommended minimum altitude for the application of the high altitude carburetor main jet is listed in the table below. In order to select the correct high altitude main jet it is necessary to identify the carburetor model. For this purpose, a code is stamped on the side of the carburetor. Select the correct high altitude jet part number corresponding to the carburetor code found on your particular carburetor. Carb. Code High Alt. Jet Part Number 16100Z2M011000M0 16161-Z152210-0000 16161-Z152010-0000 Altitude Range 3000-6000ft 914-1829 m 6000-8000ft 1829-2434 m 22 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP WARNING Operation using the alternative main jet at elevations lower than the recommended minimum altitude can damage the engine. For operation at lower elevations, the originally supplied standard main jet must be used. Operating the engine with the wrong engine configuration at a given altitude may increase its emissions and decrease fuel efficiency and performance. MAINTENANCE 4. Inspect all air vents and cooling slots to ensure that they are clean and unobstructed. Changing the Engine Oil Change oil when the engine is warm. Refer to the oil specification to select the proper grade for your operating environment. 1. Remove the oil drain bolt with a 10 mm socket (not included) and extension. MAINTENANCE Make certain that the water pump is kept clean and stored properly. Only operate the unit on a flat, level surface in a clean, dry operating environment. DO NOT expose the unit to extreme conditions, excessive dust, dirt, moisture or corrosive vapors. WARNING Never operate a damaged or defective water pump. WARNING Improper maintenance will void your warranty. NOTICE For emission control devices and systems, read and understand your responsibilities for service as stated in the Emission Control Warranty Statement of this manual. The owner/operator is responsible for all periodic maintenance. Complete all scheduled maintenance in a timely manner. Correct any issue before operating the water pump. For service or parts assistance, contact our Technical Support Team at 1-877-338-0999. Cleaning the Water Pump CAUTION DO NOT spray water pump with water. Water can contaminate the fuel system and can enter the engine through the cooling slots and damage the engine. 1. Use a damp cloth to clean exterior surfaces of the water pump. 2. Use a soft bristle brush to remove dirt and oil. 3. Use an air compressor (25 PSI) to clear dirt and debris from the water pump DRAIN BOLT 2. Allow the oil to drain completely into an appropriate container. 3. Replace the oil drain bolt. Tighten to 8.8 lbf-ft - 10.3 lbf-ft (12-14 Nm). 4. Add oil according to "Add Engine Oil" in Assembly section. DO NOT OVERFILL. Oil not included for routine maintenance. 5. Dispose of used oil at an approved waste management facility. NOTICE Once oil has been added, a visual check should show oil about 1-2 threads from running out of the fill hole. If using the dipstick to check oil level, DO NOT screw in the dipstick while checking. 23 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP Cleaning and Adjusting the Spark Plug(s) 1. Remove the spark plug cable from the spark plug. 2. Use a spark plug socket tool (not included), or a 13/16 in. (21 mm) (not included) socket to remove the plug. 3. Inspect the electrode on the plug. It must be clean and not worn to produce the spark required for ignition. 4. Make certain the spark plug gap is set within limits. Refer to the Specifications section for values. SPARK PLUG GAP 5. Refer to the spark plug section on the Specifications page when replacing the plug. 6. Carefully thread the plug into the engine. 7. Use the spark plug socket tool (not included), or a 13/16 in. (21 mm) (not included) socket to install the plug. 8. Attach the spark plug wire to the plug. Cleaning the Air Filter 1. Remove the cover holding the air filter (foam element) to the assembly. MAINTENANCE 2. Remove the foam element. 3. Wash the foam element in liquid detergent and water. Squeeze thoroughly dry. 4. Saturate in clean engine oil. 5. Squeeze in a clean, absorbent cloth to remove all excess oil. 6. Place the air filter (foam element) back into the assembly. 7. Reattach the air filter cover. Cleaning the Spark Arrestor CAUTION Failure to clean the spark arrestor will result in degraded engine performance. NOTICE Federal and local laws and administrative requirements indicate when and where spark arrestors are required. When ordered, spark arrestors are required for operation of this water pump in National Forest lands. In California, this water pump must not be used on any forest-covered land, brushcovered land, or grass-covered land unless the engine is equipped with a spark arrestor. 1. Allow the engine to cool completely before servicing the spark arrestor (if equipped). 2. Remove the screws holding the cover plate which retains the spark arrestor screen to the muffler. 3. Remove the spark arrestor screen. 4. Carefully remove the carbon deposits from the spark arrestor screen with a wire brush. 5. Replace the spark arrestor if it is damaged. 6. Position the spark arrestor on the muffler and attach with the screws. 24 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP Adjusting the Governor WARNING Tampering with the factory set governor will void your warranty. The air-fuel mixture is not adjustable. Tampering with the governor can damage your water pump and will void your warranty. Contact our Technical Support Team at 1-877-338-0999 for all other service and/or adjustment needs. Maintenance Schedule Follow the service intervals indicated in the following maintenance schedule. Service your water pump more frequently when operating in adverse conditions. Contact our Technical Support Team at 1-877-338-0999 to locate the nearest CPE certified service dealer for your water pump or engine maintenance needs. EVERY 8 HOURS OR PRIOR TO EACH USE Check oil level Clean around air intake and muffler FIRST 5 HOURS Change oil EVERY 50 HOURS OR EVERY SEASON Clean air filter Change oil if operating under heavy load or in hot environments EVERY 100 HOURS OR EVERY SEASON Change oil Clean/adjust spark plug Check/adjust valve clearance* Clean spark arrester Clean fuel tank and filter* STORAGE STORAGE Refer to the Maintenance section for proper cleaning instructions. Water Pump Storage 1. Allow the water pump to cool completely before storage. 2. Turn off the fuel supply at the fuel valve. 3. Clean the water pump according to the instructions in the Maintenance section. 4. Drain the pump chamber thoroughly. 5. Once the pump is dry, spray WD-40 or similar product into the pump housing through all ports and drainage hole. 6. Store the unit in a clean, dry area out of direct sunlight. Short Term Engine Storage (Up to 30 Days) 1. Allow the engine to cool completely before storage. 2. Clean engine according to the Maintenance section. 3. To extend the fuel storage life add a properly formulated fuel stabilizer to the fuel tank. 4. Ensure the fuel valve is in the "OFF" position. Mid Term Engine Storage ( 30 Days 1 year) 1. Add a properly formulated fuel stabilizer to the tank. 2. Run the engine for a few minutes so the treated fuel cycles through the fuel system and carburetor. 3. Turn the fuel valve to the "OFF" position. 4. Let the engine run until fuel starvation has stopped the engine. This usually takes a few minutes. The engine needs to cool completely before cleaning and storage. 5. Use a funnel (and appropriate hose if necessary) under the carburetor drain bolt to avoid spillage. Be sure to properly dispose of the drained gasoline according to local regulations or guidelines. EVERY 250 HOURS Clean combustion chamber* EVERY 3 YEARS Replace fuel line* * To be performed by knowledgeable, experienced owners or CPE certified service centers. 25 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP 6. Clean the engine according to the Maintenance section. 7. Change the oil. 8. Remove the spark plug and pour about 1/2 oz. (14.9 mL) of oil into the cylinder. Crank the engine slowly to distribute the oil and lubricate the cylinder. 9. Reattach the spark plug. Long Term Storage WARNING Never store the water pump indoors or next to appliances where there is a source of heat or open flame, spark or pilot light because they can ignite gasoline vapors. DO NOT store a water pump near fertilizer or any corrosive material. Even with an empty gas tank, gasoline vapors could ignite. STORAGE Protect your water pump from freezing. 1. Apply all storage instructions from previous sections. 2. Make sure water pump is free of all water before storing for winter. 3. In order to prevent the pump from freezing you will need to insert RV antifreeze. 4. You will need approximately 6 oz. (177.4 mL) of RV antifreeze, a funnel, and approximately 12 in. (30.5 cm) of garden hose or equivalent. 5. Pour the antifreeze into the funnel connected to the pump inlet or priming cap (top) with a small hose, then pull on the recoil starter. Pull the recoil several times to circulate the antifreeze. DANGER Engine exhaust contains odorless and colorless carbon monoxide gas. To avoid accidental or unintended ignition of the product during periods of storage, the following precautions should be followed: When storing the water pump for short or long periods of time make sure that the engine switch (where applicable) and the fuel valve are set in the "OFF" position. NOTICE Our engines work well with 10% or less ethanol blend gasoline. When using ethanol-gasoline blends there are some issues worth noting: Ethanol-gasoline blends can absorb more water than gasoline alone. These blends can eventually separate, leaving water or a watery goo in the tank, fuel valve and carburetor. With gravity-fed supplies, the compromised gasoline can be drawn into the carburetor and cause damage to the engine and/or potential hazards. There are only a few suppliers of fuel stabilizer that are formulated to work with ethanol-gasoline blends. Any damages or hazards caused by using improper gasoline, improperly stored gasoline, and/or improperly formulated stabilizers, are not covered by manufacturer's warranty. It is advisable to always shut off the gasoline supply, run the engine to starvation and drain the tank when the equipment is not in use for more than 30 days. 26 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP SPECIFICATIONS Water Pump Specifications Water Pump Type ....................................... Semi-trash Port Diameter (in./cm) ........................................ 3/7.5 Port Connection Type .......................................... NPT Discharge Rate (gal/min - L/min)........................ 264/1000 Total Head (ft/m) ............................................. 92/28 Suction Head (ft/m) .......................................... 26 / 8 Solids Handling (in/mm)..................................... 0.75/19 Impeller Material .......................................... Cast Iron Volute Material ............................................ Cast Iron Self-Priming ..................................................... Yes Hose Kit Included................................................ Yes Discharge Hose Length (ft/m) ............................... 25/7.6 Suction Hose Length (ft/m) .................................. 12/3.7 Overall Dimensions Net Weight............................................. 90 lb. (41kg) Length .............................................. 21.7 in. (55 cm) Width ................................................. 22 in. (56 cm) Height............................................... 21.3 in. (54 cm) Engine Specifications Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R224P Displacement ................................................. 224 cc Type................................................... 4-Stroke OHV Start Type .................................................... Recoil Engine Oil Specifications DO NOT OVERFILL. Type................................................ See chart below Capacity ........................................ 16.9 fl. oz (500 ml) Recommended Engine Oil Type 10W-30 5W-30 10W-40 5W-30 Synthetic °F -20 0 20 40 60 80 100 120 °C -28.9 -17.8 -6.7 4.4 15.6 26.7 37.8 48.9 Ambient temperature SPECIFICATIONS Fuel Specifications Use regular unleaded gasoline with a minimum octane rating of 87 and an ethanol content of less than 10% by volume. DO NOT USE E15 or E85. DO NOT OVERFILL. Gasoline Capacity .................................... 3 gal. (11.5 L) Spark Plug Specifications OEM Type.............................................. NHSP F6RTC Replacement Type...................... NGK BPR6ES or equivalent Gap ..................................0.028-0.031 in. (0.7-0.8 mm) Valve Specifications Intake Clearance .............. 0.0004 - 0.0006 in. (0.1-0.15 mm) Exhaust Clearance ............ 0.0006 - 0.0008 in. (0.15-0.2 mm) NOTICE A technical bulletin regarding valve adjustment procedures is available at www.championpowerequipment.com. Important Message About Temperature Your product is designed and rated for continuous operation at ambient temperatures up to 104°F (40°C). When your product is needed it may be operated at temperatures ranging from 2°F (-10°C) to 122°F (50°C) for short periods of time. If exposed to temperatures outside this range during storage, it should be brought back within this range before operation. In any event, the product must always be operated outdoors, in a well-ventilated area and away from doors, windows and vents. NOTICE Weather will affect engine oil and engine performance. Change the type of engine oil used based on weather conditions to suit the engine needs. 27 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP Parts Diagram - Frame and Engine 14 11 12 10 16 33 17 18 12 13 42 2 43 3 4 5 45 6 7 46 49 8 65 47 9 48 50 44 73 44 66 67 51 68 52 53 54 74 75 76 69 71 70 72 27 26 15 20 19 21 8 22 24 23 39 55 56 57 59 58 60 64 61 1 62 63 33 28 28 29 30 37 38 31 40 33 32 41 28 25 77 34 26 35 36 SPECIFICATIONS 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP Parts List SPECIFICATIONS # Part Number Description Qty. 1 R225MP000Q3-CMP304 Engine, 224cc 1 2 15150-Y1Z0110-00A0 Valve, One Way 1 3 16730-Z810110-0001 Fuel Tank Cap 1 4 16652-Z0M0110-00A1 Fuel Filter 1 5 90007-0625-0301 Hexagon Flange Bolt, M6 x 25, Black Zinc 4 6 90408-Y020110-0006 Flat Washer, Black Zinc 4 7 90683-Y020210-0000 Bushing 4 8 16601-Y020120-0001 Rubber, Fuel Tank 6 9 16600-V580110-L400 Fuel Tank Assembly 1 10 37200-Y1Y0110-00A1 Fuel Gauge 1 11 16804-V580110-0001 Fuel Steam Rubber Hose 1 12 90698-Y1Z0110-0001 Protective Rubber Sleeve 2 13 90685-Z030410-0001 Clamp, Ø10.7 x 0.6 x 8 1 14 30431-YBW0210-0000 Rubber Sleeve 1 15 16750-Y900111-0001 Fuel Valve Assembly 1 16 90406-0800-E109 Flat Washer 2 17 51005-V580110-0000 Vibration Mount 1, Frame 2 18 51005HV090210-0000 Vibration Mount 2, Frame 2 19 16080-V580110-0001 Choke Handle Subassembly 1 20 35541-V330310-0000 Engine Stop Wire 1 21 35160-Y450110-0000 Switch Assembly 1 22 44001-V580110-L401 Cover, Hub Decorated 2 23 44020-V580110-0300 Roll Pin, L=96, Black Zinc 2 24 44110-V580110-0000 Wheel 2 25 90722-Y9X0110-0000 End Plug 2 26 90583-YGK0110-03A0 R Pin, Black Zinc 4 27 51100-V530210-H7A0 Frame Assembly, Ø25, 510 x 395 x 450 1 28 90305-0600-0301 Hexagon Flange Nut, M6, Black Zinc 6 29 90001-0640-0301 Hexagon Flange Bolt, M6 x 40, Black Zinc 4 30 51016-V580110-H700 Support Leg 2 31 51014HY3Y0110-0000 Vibration Mount, Support Leg 2 32 90001-0625-0306 Hexagon Flange Bolt, M6 x 25, Black Zinc 2 # Part Number 33 90305-0800-0102 34 53438-V580110-QCA0 35 54101-Y9P0110-0001 36 54110-V580110-H7A0 37 18250-V580110-0000 38 90124-Y2C0110-0100 39 90303-0800-3101 40 18100-V580110-H3A0 41 90001-0835-0102 42 70107-V580110-L400 43 90001-1025-51 44 70122-V260110-0000 45 70108-V340510-0K00 46 90001-1030-01 47 90001-1020-51 48 70116-V340210-0K00 49 70115-V340110-0000 50 70107-V330110-L400 51 70109-V340110-000 52 70105-V340810-0K00 53 70104-V340110-0000 54 70103-V340110-0000 55 70102-V340210-0000 56 70119-V340110-0000 57 70125-V260210-0000 58 70309-V330110-0000 59 70300-V330110-0000 60 70300HV330110-0000 61 90001-V020110-0000 Description Qty. Hexagon Flange Nut, M8, Blue White Zinc 9 Pin Shaft, Ø8 x 65 2 Handle Sheath 1 Handle, Ø25 x 1.2 1 Spark Arrestor 1 Screw,ST4.2×9.5 4 Nut, M8, Blue White Zinc 2 Muffler Assembly 1 Hexagon Flange Bolt, M8 x 35, Blue White 1 Zinc Plug, Outlet 1 Hexagon Flange Bolt, M10 x 25, Blue White 4 Zinc Sealing Ring, Plug 2 Outlet 1 Hexagon Flange Bolt, M10 x 30, Blue White 4 Zinc Hexagon Flange Bolt, M10 x 20, Blue White 3 Zinc Inlet 1 Inlet Gasket 1 Plug, Pump Body 1 Outlet Gasket 1 Pump Body 1 Sealing Ring, Whorl Case Seal 1 Whorl Case 1 Water Pump Impeller 1 Sealing Ring, Water Pump Joint 1 Sealing Ring, Impeller 1 Friction-Piece, Silicon Carbide 1 Water Seal, Silicon Carbide 1 Seal Assembly, Mechanism 1 Hexagon Flange Bolt, 5/16-24UNF, L=60, 4 Blue White Zinc 29 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP Parts List # Part Number 62 90409-V260110-0000 63 90505-0618-00 64 70118-V340110-0K00 65 70100-V530110-WT00 66 70113-V270210-0000 67 70114-V270310-0000 68 70400-V530210-0200 69 70400-V530110-0100 70 70111-V270710-0K00 71 93161-V580110-0000 72 70134-V530110-0P00 73 71108-V530110-0000 74 71311-V530110-0000 75 70112-V340210-0000 76 70131-V270310-0000 77 94026-V530110-00E0 Description Qty. Sealing Ring, Bolt 4 Pin 2 Water Pump Joint 1 Water Pump Assembly 1 Filter Cover 1 Filter 1 Hose Clamp, Ø80-Ø85 3 Hose Clamp, Ø74-Ø79 1 Outlet hose adapter 1 Teflon Tape 1 Cam Lock Coupler 1 Suction Hose, Green 1 Discharge Hose, Blue 1 Outlet hose fitting 1 Gasket, Hose Coupler 1 Accessory Bag, 1000 x 730 mm 1 SPECIFICATIONS 30 31 7 5 6 21 22 49 42 8 11 13 87 12 14 9 47 46 45 67 79 86 62 61 44 59 60 64 57 56 58 55 54 53 65 52 63 6766 29 85 28 62 43 20 22 25 24 16 17 21 48 49 42 14 2 4 6 7 8 10 11 13 1 15 12 9 27 19 23 26 62 50 18 51 75 76 62 74 78 77 84 3 5 68 80 1 29 35 34 91 30 31 32 33 69 70 71 36 41 37 88 89 38 39 90 81 72 82 83 73 40 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP Engine Parts Diagram SPECIFICATIONS 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP Engine Parts List SPECIFICATIONS # Part Number 1 90001-0612-0101 2 12410-Z440110-0001 3 17004-Z510110-0001 4 12004-Z440110-00A0 5 14312-Z010110-0000 6 14314-Z010110-0000 7 14311-Z010110-0000 8 14313-Z010110-0000 9 14090-Z010110-0000 10 12003-Z010110-0001 11 12109-Z810110-0000 12 12112-Z810210-0000 13 12103-Z010110-0000 14 12101-Z810210-0000 15 12140-Z810210-0BA0 16 30010-Z010110-0000 17 12131-Z530320-0000 18 90502-1114-00 19 14071-Z440110-0000 20 12110-Z810120-0099 21 12121-Z810120-0000 22 12111-Z810110-0000 23 14081-Z040110-0000 24 13200-Z140210-00A9 25 13122-Z510210-0000 26 13111-Z810120-00A0 27 13121-Z810110-0000 28 13010-Z810210-00A0 29 90204-Z010210-0000 30 16002-Z050110-0000 31 16003-Z010110-0000 32 16001-Z010110-0000 Description Qty. Hexagon Flange Bolt, M6 x 12, Blue White 8 Zinc Cylinder Head Cover Subassembly, Blue 1 White Zinc Breather Tube, Ø8 x Ø12 x 100 1 Cylinder Head Cover Gasket 1 Valve Lock Nut 2 Valve Adjusting Nut 2 Valve Rocker 2 Valve Adjusting Bolt 2 Lifter Stopper Plate Subassembly, Blue 1 White Zinc Cylinder Head Bolt, M8 x 60, Blue White Zinc 4 Valve Lock Clamp 4 Valve Spring Set 2 Valve Spring 2 Seal Guide 1 Cylinder Head Subassembly 1 Spark Plug 1 Cylinder Head Gasket 1 Pin, 11 x 14 2 Valve Lifter 2 Valve Set 1 Exhaust Valve 1 Intake Valve 1 Valve Tappet 2 Piston Ring Assembly 1 Piston Pin Clip 2 Piston 1 Piston Pin, Ø13 x 45.9 1 Connecting Rod 1 Stud, M6 x 96, Black Zinc 2 Carburetor Insulator Gasket 1 Carburetor Insulator Plate 1 Carburetor Gasket 1 # Part Number 33 16100-Z2M0110-00M0 34 90686-Z510110-00M1 35 90685-Z030610-01A1 36 17001-Z010110-0000 37 17100-Z810510-0000 38 90001-0612-0101 39 17003-Y110130-0000 40 90305-0600-33 41 17151-Z300310-00A0 42 90203-Z010110-0000 43 18001-Z440110-0000 44 90502-0912-00 45 15010-Z290110-L401 46 11411-Z441310-0BA0 47 90001-0832-0101 48 11310-Z810210-0BA0 49 90682-Z300110-0001 50 90408-Z010110-0000 51 11007-Z010110-0001 52 16061-Z010110-0000 53 90408-Z010210-0000 54 90501-Z010110-0001 55 16070-Z010110-0001 56 90305-0600-3101 57 16072-Z010110-0001 58 16063-Z010310-0100 Description Qty. Carburetor Assembly 1 Fuel Pipe, Ø4.5 x Ø8.5 x 190 1 Clamp, Ø8 x 7 x 0.6 2 Air Cleaner Gasket 1 Air Cleaner 1 Hexagon Flange Bolt, M6 x 12, Blue White 1 Zinc Air cleaner Support 1 Hexagon Flange Nut, M6, Black Zinc 2 Air Cleaner Element 1 Stud, M8 x 34, Black Zinc 2 Exhaust Gasket 1 Pin, 9 x 12 2 Oil Dipstick Subassembly 1 Crankcase Cover 1 Hexagon Flange Bolt, M8 x 32, Blue White 6 Zinc Crankcase Subassembly 1 Oil Seal, Ø25 x Ø41.25 x 6 2 Washer, Ø10 x Ø15.8 x 1.5 2 Drain Plug Bolt, M10 x1.25 x15, Blue White 2 Zinc Governor Arm 1 Washer, Ø6.2 x Ø15 x 0.6 1 Pin, Blue White Zinc 1 Governor Support Subassembly, Blue 1 White Zinc Hexagon Flange Nut, M6, Blue White Zinc 1 Governor Support Bolt, M6 x 21, Blue White 1 Zinc Governor Spring 1 32 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP # Part Number 59 16062-Z010110-0001 60 16012-Z010310-0000 61 16520-Z440410-0101 62 90001-0610-0101 63 37060-Z010120-0001 64 90001-0614-01 65 90305-Z010210-0101 66 16400-Z810210-0000 67 90547-0205-00 68 13510-Z440410-0000 69 19352-Z440110-0001 70 28002-Z0L0110-0000 71 13501-Z010110-0000 72 30400-Z440410-0001 73 90001-0625-01 74 19304-Z010610-0001 75 90684-Z010510-0000 76 19340-Z011010-0000 77 90001-0616-01 78 37050-Z010210-0001 79 11001-Z440110-00A0 80 28110-Z010610-L400 81 28200-Z141010-H301 82 90408-0600-03 83 90001-0608-03 84 30009-Z010210-0000 85 14200-Z810310-0000 86 13300-Z811910-0000 Description Qty. Governeor Rod, Blue White Zinc 1 Throttle Valve Returning Spring 1 Throttle Control Assembly, Blue White 1 Zinc Hexagon Flange Bolt, M6 x 10, Blue White 5 Zinc Engine oil Sensor, W/O Nut 1 Hexagon Flange Bolt, M6 x 14, Blue White 2 Zinc Hexagon Flange Nut, M10, Blue White Zinc 1 Governor Gear Assembly 1 Bearing 2 Flywheel Subassembly 1 Impeller 1 Starter Pulley, Blue White Zinc 1 Flywheel Nut, M14 x 1.5, Blue White Zinc 1 Ignition Coil 1 Hexagon Flange Bolt, M6 x 25, Blue White 2 Zinc Cylinder Body Shroud 1 Clip 1 Lower Shield 1 Hexagon Flange Bolt, M6 x 16, Blue White 1 Zinc Oil Protector, Blue White Zinc 1 Crankcase Gasket 1 Shroud 1 Recoil Starter Assembly 1 Washer, Black Zinc 3 Hexagon Flange Bolt, M6 x 8, Black Zinc 3 Grounding Wiring 1 Camshaft Assembly 1 Crankshaft Assembly 1 SPECIFICATIONS # Part Number Description Qty. 87 210P-001 Cylinder Head Subassembly 1 16161-Z152410-0000 Main Jet, Standard 1 88 16161-Z152210-0000 Main Jet, Altitude 3000-6000 Feet / 16161-Z152010-0000 Main Jet, Altitude 6000-8000 Feet / 89 16112-Z010110-0000 Seal Ring, Float 1 90 90681-Z010610-0000 Seal Ring 1 91 30431-Y020110-0001 Rubber Sleeve 1 33 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP TROUBLESHOOTING TROUBLESHOOTING Problem Pump will not start. Pump will not pump. Pump will not prime. Priming takes a long time. Pump does not perform as well as it should. Pump loses prime. Cause No fuel. Low oil. Faulty spark plug or cable Fuel valve lever is in the OFF position. Ignition switch is in the OFF position. Choke is in the wrong position. Air leak in suction hose. The suction and/or discharge line(s) may be blocked. The end of the suction line is not submerged. Total head is too high for this pump to work against Allow more time Hose clamps on inlet hose are not tight. Excessive suction lift (*1). Excessive head lift. Water not added through the top prime cap. Suction line is quite long. Air pockets or leaks in the suction line. Flow is restricted due to debris build-up. Insufficient submergence of the end of suction hose. Excessively worn impeller (*2). Seal is damaged (*3). Liquid will be leaking through the middle of the adapter. Air pockets or leaks in the suction hose. Clogged impeller. Engine throttle is in SLOW position. Water level drops below the end of the suction line. Solution Allow engine to cool for 2 minutes, then fill fuel tank. Fill or check oil is to the proper level; place water pump on a flat, level surface. Replace spark plug or check spark plug cable is seated properly. Turn the fuel valve lever to the ON position. Turn the ignition switch to the ON position. Slide choke lever to the CHOKE position. Make sure suction hose is double clamped at joints, clamps are tight, fittings have thread compound and are tight, with no nicks or cuts in hose. Check to see that the hoses and filter are in good working order. Increase its length, or move pump closer to source of liquid. Reduce total head or use a higher head pump. It may take up to 6 minutes to prime water up to the pump, depending on suction lift height. Even small pinhole leak can result in vacuum loss preventing pump from priming. Check hose clamps to ensure they are tight. Adjust clamp position if necessary." Move the pump closer to liquid source. Relocate pump so suction head is less than discharge head. Review "Priming the Pump" section. Move pump closer to source. Check the line for loose connections. Make sure suction hose is submerged. Clean the hoses, fittings and filter. The end of the suction line must be submerged. Replace impeller. Replace the seal. Check suction hose. Remove casing to clean out. Move throttle to FAST position. Increase length of suction line or move the pump closer to the water source. 34 100743 - 3 IN. (7.5 CM) SEMI-TRASH PUMP TROUBLESHOOTING Problem Pump starts, but runs roughly. Pump shuts down during operation. Excessive suction lift must take into consideration: A. Size and length of pipe B. Pipe fitting C. Elevation above sea level Including all of the above, we recommend that the total suction head not exceed 26' Cause Choke is in the wrong position. Spark plug wire is loose. Faulty spark plug. Fuel is contaminated (water, debris, etc.). No fuel. Low oil sensor shuts down unit. An excessively worn impeller is mainly caused from cavitation, which is caused by a number of situations, such as: Solution Slide choke lever to the RUN position. Attach wire to spark plug securely. Replace spark plug. Allow engine to cool for 2 minutes, then drain fuel tank and carburetor. Fill tank with fresh fuel. Allow engine to cool for 2 minutes, then fill fuel tank. Make sure unit is on flat surface. Check oil level and add more if necessary. A. Restricted suction B. Excessive suction lift The seal may be damaged due to: A. Normal wear B. Overheating C. Pumping chemicals that this seal is not designed for. For further technical support: Technical Support Team Mon-Fri 8:30 AM-5:00 PM (PST/PDT) Toll Free 1-877-338-0999 support@championpowerequipment.com 35 WARRANTY* CHAMPION POWER EQUIPMENT 2 YEAR LIMITED WARRANTY Warranty Qualifications To register your product for warranty and FREE lifetime call center technical support please visit: https://www.championpowerequipment.com/register To complete registration you will need to include a copy of the purchase receipt as proof of original purchase. Proof of purchase is required for warranty service. Please register within ten (10) days from date of purchase. Repair/Replacement Warranty CPE warrants to the original purchaser that the mechanical and electrical components will be free of defects in material and workmanship for a period of two years (parts and labor) from the original date of purchase and 90 days (parts and labor) for commercial and industrial use. Transportation charges on product submitted for repair or replacement under this warranty are the sole responsibility of the purchaser. This warranty only applies to the original purchaser and is not transferable. Do Not Return The Unit To The Place Of Purchase Contact CPE's Technical Service and CPE will troubleshoot any issue via phone or e-mail. If the problem is not corrected by this method, CPE will, at its option, authorize evaluation, repair or replacement of the defective part or component at a CPE Service Center. CPE will provide you with a case number for warranty service. Please keep it for future reference. Repairs or replacements without prior authorization, or at an unauthorized repair facility, will not be covered by this warranty. Warranty Exclusions This warranty does not cover the following repairs and equipment: Normal Wear Products with mechanical and electrical components need periodic parts and service to perform well. This warranty does not cover repair when normal use has exhausted the life of a part or the equipment as a whole. Installation, Use and Maintenance This warranty will not apply to parts and/or labor if the product is deemed to have been misused, neglected, involved in an accident, abused, loaded beyond the product's limits, modified, installed improperly or connected incorrectly to any electrical component. Normal maintenance is not covered by this warranty and is not required to be performed at a facility or by a person authorized by CPE. Other Exclusions This warranty excludes: Cosmetic defects such as paint, decals, etc. Wear items such as filter elements, o-rings, etc. Accessory parts such as hoses, hose fittings, etc. Failures due to acts of God and other force majeure events beyond the manufacturer's control. Problems caused by parts that are not original Champion Power Equipment parts. When applicable, this warranty does not apply to products used for prime power in place of a utility. Limits of Implied Warranty and Consequential Damage Champion Power Equipment disclaims any obligation to cover any loss of time, use of this product, freight, or any incidental or consequential claim by anyone from using this product. THIS WARRANTY AND THE ATTACHED U.S. EPA and/or CARB EMISSION CONTROL SYSTEM WARRANTIES (WHEN APPLICABLE) ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. A unit provided as an exchange will be subject to the warranty of the original unit. The length of the warranty governing the exchanged unit will remain calculated by reference to the purchase date of the original unit. This warranty gives you certain legal rights which may change from state to state or province to province. Your state or province may also have other rights you may be entitled to that are not listed within this warranty. Contact Information Address Champion Power Equipment, Inc. 12039 Smith Ave. Santa Fe Springs, CA 90670 USA www.championpowerequipment.com Customer Service Toll Free: 1-877-338-0999 info@championpowerequipment.com Fax no.: 1-562-236-9429 Technical Service Toll Free: 1-877-338-0999 tech@championpowerequipment.com 24/7 Tech Support: 1-562-204-1188 *Except as otherwise stipulated in any of the following enclosed Emission Control System Warranties (when applicable) for the Emission Control System: U.S. Environment Protection Agency (EPA) and/or California Air Resources Board (CARB). CHAMPION POWER EQUIPMENT, INC. (CPE) AND THE UNITED STATES ENVIRONMENTAL PROTECTION AGENCY (U.S. EPA) EMISSION CONTROL SYSTEM WARRANTY Your Champion Power Equipment (CPE) engine complies with U.S. EPA emissions regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The US EPA and CPE are pleased to explain the Federal Emission Control Systems Warranty on your 2020 small off-road engine (SORE) and engine powered equipment. New engines and equipment must be designed, built and equipped, at the time of sale, to meet U.S. EPA regulations for small off-road engines (SORE). CPE warrants the emission control system on your small off-road engine (SORE) and equipment for the period of time listed below, provided there has been no abuse, neglect, unapproved modification, or improper maintenance of your equipment. Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition system, catalytic converter and fuel lines. Also included may be hoses, belts, connectors and other emission related assemblies. Where a warrantable condition exits, CPE will repair your small off-road engine (SORE) at no cost to you including diagnosis, parts and labor. MANUFACTURER'S EMISSION CONTROL SYSTEM WARRANTY COVERAGE: This emission control system is warranted for two years, subject to provisions set forth below. If, during the warranty period, an emission related part on your engine is defective in materials or workmanship, the part will be repaired or replaced by CPE. OWNER WARRANTY RESPONSIBILITIES: As the small off-road engine (SORE) owner, you are responsible for the performance of the required maintenance listed in your Owner's Manual. CPE recommends that you retain all your receipts covering maintenance on your small off-road engine, but CPE cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the small off-road engine (SORE) owner, you should however be aware that CPE may deny you warranty coverage if your small, off-road engine (SORE) or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications. You are responsible for presenting your small off-road engine (SORE) to an Authorized CPE service outlet or alternate service outlet as described in (3)(f.) below, CPE dealer or CPE, Santa Fe Springs, Ca. as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and responsibilities, you should contact: Champion Power Equipment, Inc. Customer Service 12039 Smith Ave. Santa Fe Springs, CA 90670 1-877-338-0999 tech@championpowerequipment.com EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1997 and later model year small off-road engines (SORE). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter. 2. GENERAL EMISSIONS WARRANTY COVERAGE CPE warrants to the original, end-use purchaser of the new engine or equipment and to each subsequent purchaser that each of its small off-road engines (SORE) is: 2a. Designed, built and equipped so as to conform to U.S. EPA emissions standards for spark-ignited engines at or below 19 kilowatts. 2b. Free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material respects to the part as described in the engine manufacturer's application for certification for a period of two years. 3. THE WARRANTY ON EMISSION-RELATED PARTS WILL BE INTERPRETED AS FOLLOWS: 3a. Any warranted part that is not scheduled for replacement as required maintenance in the Owners Manual shall be warranted for the ECS Warranty Period. If any such part fails during the ECS Warranty Period, it shall be repaired or replaced by CPE according to Subsection "d" below. Any such part repaired or replaced under the ECS Warranty shall be warranted for any remainder of the ECS Warranty Period. 3b. Any warranted, emissions-related part which is scheduled only for regular inspection as specified in the Owners Manual shall be warranted for the ECS Warranty Period. A statement in such written instructions to the effect of "repair or replace as necessary", shall not reduce the ECS Warranty Period. Any such part repaired or replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty Period. 3c. Any warranted, emissions-related part which is scheduled for replacement as required maintenance in the Owner's Manual shall be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part shall be repaired or replaced by CPE according to Subsection "d" below. Any such emissionsrelated part repaired or replaced under the ECS Warranty, shall be warranted for the remainder of the ECS Warranty Period prior to the first scheduled replacement point for such emissions-related part. 3d. Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall be performed at no charge to the owner at a CPE Authorized Service Outlet. 3e. The owner shall not be charged for diagnostic labor which leads to the determination that a part covered by the ECS Warranty is in fact defective, provided that such diagnostic work is performed at a CPE Authorized Service Outlet. 3f. CPE shall pay for covered emissions warranty repairs at non-authorized service outlets under the following circumstances: i. The service is required in a population center with a population over 100,000 according to U.S. Census 2000 without a CPE Authorized Service Outlet AND ii.The service is required more than 100 miles from a CPE Authorized Service Outlet. The 100 mile limitation does not apply in the following states: Alaska, Arizona, Colorado, Hawaii, Idaho, Montana, Nebraska, Nevada, New Mexico, Oregon, Texas, Utah and Wyoming. 3g. CPE shall be liable for damages to other original engine components or approved modifications proximately caused by a failure under warranty of an emission-related part covered by the ECS Warranty. 3h. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted emission-related parts sufficient to meet the expected demand for such emission-related parts. 3i. Any CPE Authorized and approved emission-related replacement part may be used in the performance of any ECS Warranty maintenance or repair and will be provided without charge to the owner. Such use shall not reduce CPE's warranty obligation. 3j. Unapproved add-on or modified parts may not be used to modify or repair a CPE engine. Such use voids this ECS Warranty and shall be sufficient grounds for disallowing an ECS Warranty claim. CPE shall not be liable hereunder for failures of any warranted parts of a CPE engine caused by the use of such an unapproved add-on or modified part. EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list applicable to the engine) Systems covered by this warranty Fuel Metering System Air Induction System Ignition System Exhaust System Miscellaneous Parts Evaporative Emissions Parts Description Fuel regulator, Carburetor and internal parts Air cleaner, Intake manifold Spark plug and parts, Magneto ignition system Exhaust manifold, catalytic converter Tubing, Fittings, Seals, Gaskets, and Clamps associated with these listed systems. Fuel Tank, Fuel Cap, Fuel Lines (for liquid fuel and fuel vapors), Fuel Line Fittings, Clamps, Pressure Relief Valves, Control Valves, Control Solenoids, Electronic Controls, Vacuum Control Diaphragms, Control Cables, Control Linkages, Purge Valves, Gaskets, Liquid/Vapor Separator, Carbon Canister, Canister Mounting Brackets, Carburetor Purge Port Connector TO OBTAIN WARRANTY SERVICE: You must take your CPE engine or the product on which it is installed, along with your warranty registration card or other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours. Alternate service locations defined in Section (3)(f.) above must be approved by CPE prior to service. Claims for repair or adjustment found to be caused solely by defects in material or workmanship will not be denied because the engine was not properly maintained and used. If you have any questions regarding your warranty rights and responsibilities, or to obtain warranty service, please write or call Customer Service at Champion Power Equipment, Inc. Champion Power Equipment, Inc. 12039 Smith Ave. Santa Fe Springs, CA 90670 1-877-338-0999 Attn.: Customer Service tech@championpowerequipment.com