This manual must be read and understood before the installation and operation of this dispenser. Taprite 3248 Northwestern Drive • San Antonio, TX 78238 210.662.8200 • Fax: 210.646.6009 • www.taprite.com Toll-Free 877.404.2488 Re: 1/24/2020 PN: 805-0039GB 3158001 disenser model No 950C instructional manual rattler beverage disenser / /
instructional manual rattler beverage dispenser dispenser model No. 950C Please refer to the Taprite website (www.taprite.com) for information relating to Taprite installation and Service Manuals, Instruction Sheets, Technical Bulletins, Service Bulletins, etc. Rev: 1/24/2020 PN: 805-0039GB 3158001 NOTICE: The information contained in this document is subject to change without notice. TAPRITE MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TAPRITE shall not be liable for errors contained herein or for incidental consequential damages in connection with the finishings, performance, or use of this material. This document contains proprietary information which is protected by copyright. All rights reserved. © Copyright 2019 by Taprite, all rights reserved. THIS DOCUMENT CONTAINS IMPORTANT INFORMATION This manual must be read and understood before the installation and operation of this dispenser. Taprite 3248 Northwestern Drive · San Antonio, TX 78238 210.662.8200 · Fax: 210.646.6009 · www.taprite.com Toll-Free 877.404.2488 / / TABLE OF CONTENTS SUBJECT Installation Setting Ratio Flow Control Cover Installation Butterfly Plate and Button Removal/Reassembly Removing and Replacing Stem O-Ring Cleaning and Maintenance Reattaching the Bar Gun Assembly Troubleshooting Line Configuration Juice and Energy Butterfly Plate Configurations 8 and 10 Butterfly Plate Configurations 12 and 14 Butterfly Plate Configurations Button Plate Configurations Accessories Handle Assembly Manifold Assembly Flow Control Module Assembly Mechanical Module Assembly Mounting Plate Screw Placement Patent & Patent Pending Numbers Part Number Format PAGE NUMBER 3 5 7 7 7 8-9 10 11 12 13 14 15-16 17 18-19 20-21 22-23 24-25 26-27 28 28 29 2 INSTALLATION Thank you for purchasing a Taprite 950C bar dispenser. All required mounting hardware, holster assembly, and ¼" stainless-steel input fittings (with o-rings) are included with each bar dispenser. The stainless-steel input fittings are installed on the product side of the bar dispenser manifold (Fig. 1). These fittings are secured in place using the red retainer clips. Fig. 1 IMPORTANT THIS EQUIPMENT MUST BE CONNECTED TO A POTABLE WATER SUPPLY AND INSTALLED WITH ADEQUATE BACK FLOW PREVENTION TO COMPLY WITH FEDERAL, STATE, AND LOCAL CODES. Attach the base plate (smooth side out) with provided #8 screws. Please see Page 26 for optimal screw placement. IMPORTANT THE BASEPLATE PROVIDES STABILITY FOR THE BAR DISPENSER AND SHOULD BE ATTACHED TO A FLAT SURFACE. FAILURE TO INSTALL THE BAR DISPENSER AND BASEPLATE ON A FLAT SURFACE WILL VOID THE WARRANTY AND MAY CAUSE THE VALVE MODULE ASSEMBLY TO LEAK. To install the fitting, press the barb side of the fitting into the tubing and past the last fittings barb. Secure the tubing to the fitting with an Oetiker clamp positioned upright. INSTALLER TIP: Do not install the tubing flush with the flange, this will cause the tubing to interfere with the retainer clip. Failure to install Oetikers as shown in Figure 1 will place stress on the valve module assembly and cause a leak. A. If a staggered setup is necessary, input fittings are available in two additional lengths: "medium" (1.5" length), and "long" (2.7" length) (Fig. 2). 3 Fig. 2 B. Follow the labeling on the assembly to ensure proper product connection. C. Lock inlet line fittings into the valve module assembly before turning on syrup or water. To lock the fitting, lightly press down on the red clip. Lightly pull up on the clip to allow fitting removal. (Caution: Forcibly removing the red clip from the valve body may damage the clip). Fig. 3 D. The bar dispenser assembly comes from the factory pre-attached to the valve module assembly. Before proceeding to the next step verify that the red retainer clips are in the locked position (down) (Fig. 3). E. Rotate the yellow shut-off stem 90 degrees to "Off" position to check for inlet connection leaks (Fig. 4). Off Fig. 4 F. Slide Flow Control Module/Mechanical Module (FCM/MM) onto base plate and verify that the two bosses on the plate are lined up. Secure the manifold to the base plate with the two thumb screws. G. To install the holster use the screws provided. Install the holster and drain assembly 4 in close proximity to the bar gun location. Holster mounting plate must be placed so that the release tab is accessible. Plumb the holster using 1/2" standard drain hose and follow local plumbing codes. Refer to the cleaning and maintenance section for proper removal and cleaning of holster. Release Tab Fig. 5 IMPORTANT NEVER PLACE THE HOLSTER DIRECTLY OVER THE ICE BIN. HOLSTER INSERT CAN BE REMOVED AND USED WITH OTHER BAR DISPENSER HOLSTERS. INSTALLER TIP: Place your bar dispenser as close as possible to the product cooling source to minimize the dispensing of warm product and reduce foaming of the finished drinks. SETTING RATIO The Bar Dispenser has been thoroughly tested and sanitized prior to shipment. The installer will be required to set the ratio of the bar dispenser. INSTALLER TIP: Installer must cool or chill the product before setting the ratio of the system. Ratio will be different in cold product and warm product. IMPORTANT BEFORE SETTING RATIO, PURGE PRODUCT AND WATER THROUGH BAR DISPENSER TO ENSURE PROPER PRODUCT TEMPERATURE. A. Rotate the yellow shut-off stem to the "on" position (Fig. 4). B. To adjust water flow rate, press plain water button or carbonated water button on bar dispenser and capture water in a graduated cylinder or ratio cup, while timing the dispense. Divide the volume of water dispensed by the time. This will equal the flow rate in oz/s C. To adjust the flow, turn the red adjustment screw (Fig 6). To regulate a ceramic FCM, turn clockwise to increase flow and counterclockwise to decrease flow. If the flow control assembly contains a green adjustment screw it is a MM. To regulate flow, turn counterclockwise to increase flow and clockwise to decrease flow (opposite of ceramic flow control) (Fig. 7) 5 Adjustment Screw Fig. 6 Increase Decrease Fig. 7 Decrease Metering Screw Increase NOTE: The Bar Dispenser is designed to flow 1.50 oz/sec. finished drink. This is the proper setting for 5:1 ratio. D. To achieve the proper water flow rate, adjust the red screw within the flow control module. For the mechanical application adjust the green metering screw (Fig. 7). INSTALLER TIP: Depending on the pressure of the incoming plain water, the maximum flow for the dispens- er may not be achievable. There are two solutions to this problem. 1) Adjust the Brix/Ratio to account for the slower flow rate. 2) Add a water booster to the system. E. To Ratio/Brix the final product, remove dispensing nozzle on bar gun assembly. F. Replace the dispensing nozzle with the Taprite syrup separator nozzle. Line up the separator nozzle on the diffuser and turn to lock the nozzle in place. Ensure there is a tight seal against the diffuser. G. Use a ratio cup to measure the syrup to water ratio. Adjust the flow controls to achieve the target ratio. INSTALLER TIP: The Taprite Bar Dispenser is equipped with a secondary water ratio screw that is located on the bottom of the bar dispenser handle near the nozzle (Fig. 8). This may be used to slow the flow of water to maintain proper ratio for products with ratios 1:1 or 2:1 or any high-viscosity product. The screw comes from the factory in the open position and should be used only in the conditions noted. This screw only controls water flow to the products associated with the bottom right hand butterfly plate. Secondary Water Ratio Screw Fig. 8 6 FLOW CONTROL COVER INSTALLATION A. Loosen thumb screws keeping them evenly spaced for the cover to slide between. B. To install flow control cover, align the slots on the cover with the thumb screws on the valve/ bracket assembly. C. Align slot with thumb screws and tighten on each side of cover. *Note: Thumb screws do not have to be removed completely* BUTTERFLY PLATE AND BUTTON REMOVAL/REASSEMBLY Taprite Bar Dispenser can be configured for numerous combinations of carbonated and noncarbonated products. All combinations can be made without shutting down the product and soda/water system. The button plate can be removed while the bar dispenser is pressurized by simply removing the two screws on the bar dispenser head. A. To change butterfly plate, remove button plate. B. Remove both Phillips screws and butterfly retainers. C. Lift butterfly plates out of handle. D. Align the pivot balls of the replacement plates located on the bottom of the butterfly plate, with the depressions in the bar gun handle. INSTALLER TIP: The pivot balls on the butterfly plate must align with the depressions in the bar dispenser handle for the bar dispenser to work properly. E. Secure butterfly plates in position using the Phillips screws and butterfly retainers (BE CAREFUL NOT TO OVERTIGHTEN). F. Replace button plate and reattach with Phillips screws. REMOVE AND REPLACE STEM O-RING A. Rotate yellow Shut-off stem 90 degrees on module assembly to turn off water and prod- ucts. Press the buttons on the bar dispense to release the pressure. B. Place bar gun handle on flat surface, nozzle facing up. C. Remove the button and the butterfly plates. The valve stems are located under the plates. INSTALLER TIP: Carefully remove bottom plate, by lifting straight up. Small springs are located below the plate and may fall out. D. Remove Phillips screws and the bottom plate E. Using an appropriate tool, push valve stem down and out of the handle. F. Working from the botton plate side, use the spear end of the o-ring tool (P.N. 316-0003) to remove the o-ring (P.N. 208- 5003) G. Place new o-rings on the plain end of the tool, lubricate with a small amount of food grade lubricant. H. Install o-ring in the hole and make sure it is firmly seated. INSTALLER TIP: It is required to use a food grade lubricant. I. Replace valve stem, install springs in the valve handle. 7 INSTALLER TIP: ALL VALVE SPRINGS MUST BE SEATED IN THE RECESS OF THE BOTTOM PLATE TO PROPERLY ALIGN WITH THE HANDLE. J. Slowly press bottom plate into handle until it is completely seated. K. Hold the bottom plate and replace the retaining screws. INSTALLER TIP: DO NOT OVER TIGHTEN THE RETAINING SCREWS. L. Replace butterfly plates. M. Replace button plate. CLEANING AND MAINTENANCE The Bar Dispenser is shipped from the factory cleaned and sanitized in accordance with NSF guidelines. The bar dispenser must also be cleaned and sanitized after installation is complete. It is recommended that the operator provide continuous maintenance as required by the manual and/or state and local guidelines to ensure proper operation. IMPORTANT DO NOT CLEAN WITH OR ALLOW CONTACT WITH HARSH CHEMICALS CONTAINING ATBC (ACETYL TRIBUTYL CITRATE) OR OTHER ORGANIC SOLVENTS (CLEANER/ DEGREASERS, PESTICIDES AND PESTICIDE FOGGERS). THIS WILL CAUSE PERMANENT DAMAGE TO PLASTIC COMPONENTS. HANDLE IMPORTANT DO NOT SUBMERGE THE HANDLE IN HOT WATER. THIS WILL CAUSE PERMANENT DAMAGE TO THE DISPENSER AND ITS COMPONENTS. A.External Cleaning Cleaners (ivory liquid, calgon, etc.) should be mixed with clean potable water at a temperature of 90 to 110 degrees F. The acceptable mixture ratio is one ounce of cleanser to two gallons of water. Any NSF approved equivalent cleaner may be used. Rinse with clean potable water. IMPORTANT ONLY USE INTERNAL CLEANING SOLUTIONS THAT ARE APPROVED FOR BEVERAGE DISPENSER APPLICATIONS, SUCH AS KAY-5®. (NO CAUSTIC CHEMICALS SUCH AS INDUSTRIAL KITCHEN CLEANING CHEMICALS SHOULD EVER BE USED) B. Sanitizing Sanitizing solutions must provide 50 to 100 parts per million (PPM) available chlorine. Any sanitizing solution may be used as long as it is prepared in accordance with the manufacturer's recommendations. C.Daily Cleaning 1. Dispenser Handle Remove nozzle from bar dispenser handle. Fill container about 6" with warm (never hot) water. Allow the dispenser handle and nozzle to soak in the water for 10 to 15 minutes. This will remove any syrup or soda residue from the nozzle and buttons. It should not be soaked overnight. 8 NOTE: It is recommended that the nozzle be removed and cleaned daily. 2. All external parts can be cleaned by wiping with a cloth soaked with warm cleansing detergent. Inspect the hose to ensure all residue is removed. D.Deep Cleaning of Bar Dispenser Whip 1. Rotate yellow Shut-off stem 90 degrees to turn off water/product (Fig. 9). 2. Turn the two (2) wing screws to release the FCM/MM from the base plate (Fig 10). 3. Slide FCM/MM module out of mounting plate. 4. Snap the red retainer clips to the open position (Fig 11). 5. Locate the two slotted red screw separators on the outside of the bar gun manifold and turn the screws clockwise. This will separate the bar gun dispenser from the FCM/MM module (Fig. 12). NOTE: Alternate turning red screw separator to evenly remove the bar gun manifold from the module. The Shut-off tool (P.N. 316-0005), or a screw driver, can be used to aid in removing the dispenser assembly but is not necessary. Fig. 9 Fig. 10 Fig. 11 Fig. 12 Red Clips Screws 6. Fill a bar sink or a 5 gal. bucket with sanitizing solution that is mixed to mfg. recommendations (50 to 100 PPM). Allow the bar gun whip assembly to soak in the solution for 10 to 15 minutes. Using a cloth and brush, wash and clean the hose. Inspect the hose to ensure all residue is removed. It should not be soaked overnight. 9 7. Rinse with warm water and allow to dry. E.Holster Cleaning 1. Daily Cleaning For daily cleaning, press carbonated water button or water button on bar handle while sitting in the holster to flush product residue down drain. You may also pour warm water down the receptacle to clean holster. 2. Bi-weekly Cleaning a. To remove holster assembly, push tab located behind the nozzle receptacle. Slide holster assembly forward (toward you) (Fig. 13-14). b. Separate the bar gun receptacle from the drip tray (Fig. 15). c. Refer to sanitizing section in 3-B. Fig. 13 Fig. 14 Fig. 15 NOTE: Check the back of the drip tray drain connector to ensure there is no damage to the o-rings (P.N. 208-5112-429) (Fig. 15) REATTACHING THE BAR GUN WHIP ASSEMBLY A. Adjust the red screw separators on the outside of the bar gun assembly so the small smooth shank is exposed. B. Slide the bar gun manifold into the FCM/MM module. C. Snap red retainers into the locked position. D. Slide FCM/MM module and bar dispenser into locked position on mounting plate and secure with wing screws E. Rotate yellow Shut-off stem 90 degrees to the open position and check for leaks. F. Depress all buttons on bar dispenser head to remove any trapped air or sanitizing solution. G. Bar Dispenser is ready for operation. 10 TROUBLE SHOOTING A. Push water - no water dispensed · Check water supply · Check Shut-off (is it open) · Check ratio/brix adjustment · Check for proper butterfly plate B. Push syrup - no syrup dispensed · Check C02 pressure · Check for product · Check Shut-off · Check ratio/brix adjustment · Line plugged C. Push soda - no soda dispensed · Check carbonator · Check water supply · Check C02 pressure · Check Shut-off · Check ratio/brix adjustment · Check for proper butterfly plate D. Push product - dispensing incorrect product · Check for proper plumbing · Check for proper butterfly plate E. Weak product taste · Check syrup C02 supply · Check ratio/brix adjustment · Check for plugged line · Check Shut-off - open completely · Check syrup supply F. Strong product taste · Check ratio/brix adjustment · Check carbonator pressure · Check syrup C02 G. Continuous dispense · Check butterfly plates - damaged or too tight · Check for debris in syrup or water passages H. Product leaking from bottom plate · Defective stem o-ring · Bottom plate screws are loose · Warped or damaged button plate 11 LINE CONFIGURATION 8 Button UP 808-0054 S5 SODA S6 S1 S3 S4 S2 WATER END OF HANDLE 808-0055 S1 S2 SODA S3 S4 S5 S6 WATER INLET END S7 S5 S1 S3 SODA WATER S4 S2 S6 S8 10 Button UP 808-0054 S5 SODA S6 S1 S3 S4 S2 S7 WATER S8 END OF HANDLE 808-0055 S1 S2 SODA S3 S4 S5 S6 WATER S7 S8 INLET END S7 S5 S1 S3 SODA WATER S4 S2 S6 S8 12 Button UP 808-0061 S5 S6 S7 SODA S8 S1 S3 S4 S2 S9 S10 WATER END OF HANDLE 808-0063 S1 S2 SODA S3 S4 S5 S6 S7 S8 WATER S9 S10 INLET SIDE S11 S9 S7 S5 S1 S3 SODA WATER S4 S2 S6 S8 808-0062 S10 S12 14 Button UP 808-0071 S7 S5 S6 S8 S9 SODA S10 S1 S3 S4 S2 S11 WATER S12 END OF HANDLE 808-0064 S1 S2 SODA S3 S4 S5 S6 S7 S8 S9 S10 WATER S11 S12 INLET SIDE S11 S9 S7 S5 S1 S3 SODA WATER S4 S2 S6 S8 808-0062 S10 S12 12 JUICE AND ENERGY BUTTERFLY PLATE CONFIGURATION 950-J066 Button 3HL 2H 950-J088 Button 3HL 2H 950-J1010 Button 950-J1212 Button 3HL 3HR 3HL 3HR * * 1HL 2H 1HL 2H * * #H 1HL 1HR 2H 3HL 3HR 4HL 4HR 4H#3 4H#4 Butterfly Plate Assy Part Number 634-0001 634-0002 634-0003 634-0004 634-0005 634-0006 634-0007 634-0008 634-0009 * * 2H 2H 3HR 3HL * * * 950-011001 Button 1HR 1HL 950-022002 Button 1HR 1HL = Carbonated Positions = Non-Carbonated Positions = Secondary Water Metering Screw Affects These Positions ® = Requires Soda/Water Button Foot (P.N. 265-0039/265-0040) Extensions Into Bottom Of Button Where Symbol Appears. 13 8 AND 10 BUTTON BUTTERFLY PLATE CONFIGURATIONS 950-108008 Button Carbonated 0 Button Non-Carbonated 0 Pre-Mix 950-107107 Button Carbonated 1 Button Non-Carbonated 0 Pre-Mix 950-10620- & 950-086006 Button Carbonated 2 Button Non-Carbonated 0 Pre-Mix 4HL 4HR 4HL 3HR 3HL 3HR ® ® ® 1HR 1HL 1HR * * 950-10530- & 950-085105 Button Carbonated 3 Button Non-Carbonated 0 Pre-Mix 3HL 2H * 2H 1HL * 950-104404 Button Carbonated 4 Button Non-Carbonated 0 Pre-Mix 2H 2H * 2H 2H * 950-103503 Button Carbonated 5 Button Non-Carbonated 0 Pre-Mix 1HL 2H * * 2H 3HL * 950-102602 Button Carbonated 6 Button Non-Carbonated 0 Pre-Mix 1HR 1HL * * 3HR 3HL * 950-101701 Button Carbonated 7 Button Non-Carbonated 0 Pre-Mix * 1HR ® * * 3HR 4HL * 950-100800 Button Carbonated 8 Button Non-Carbonated 0 Pre-Mix * ® ® * * 4HR 4HL * = Carbonated Positions = Non-Carbonated Positions #H = See Chart on Page 12 for Part Number = Secondary Water Metering Screw Affects These Positions ® = Requires Soda/Water Button Foot (P.N. 265-0039/265-0040) Extensions Into Bottom Of Button Where Symbol Appears. 14 BUTTERFLY PLATE CONFIGURATIONS 12 AND 14 BUTTON BUTTERFLY PLATE CONFIGURATIONS 950-128208 Button Carbonated 2 Button Non-Carbonated 0 Pre-Mix 950-127307 Button Carbonated 3 Button Non-Carbonated 0 Pre-Mix 950-126406 Button Carbonated 4 Button Non-Carbonated 0 Pre-Mix 4H#3 4H#4 4H#3 3HR 3HL 3HR * 2H 1HL 1HR 1HL * * * 2H 2H * 950-125505 Button Carbonated 5 Button Non-Carbonated 0 Pre-Mix 2H 3HR 3HR * 2H * 950-124604 Button Carbonated 6 Button Non-Carbonated 0 Pre-Mix 2H 2H * 3HR 3HL * * 950-123703 Button Carbonated 7 Button Non-Carbonated 0 Pre-Mix 1HR 2H * * 4H#4 3HL * * = Carbonated Positions = Non-Carbonated Positions #H = See Chart on Page 12 for Part Number = Secondary Water Metering Screw Affects These Positions ® = Requires Soda/Water Button Foot (P.N. 265-0039/265-0040) Extensions Into Bottom Of Button Where Symbol Appears. 15 BUTTERFLY PLATE CONFIGURATIONS 12 AND 14 BUTTON BUTTERFLY PLATE CONFIGURATIONS 950-122802 Button Carbonated 8 Button Non-Carbonated 0 Pre-Mix 1HR 1HL * 4H#4 * 4H#3 * * 950-146606 Button Carbonated 6 Button Non-Carbonated 0 Pre-Mix 3HL 3HR 950-148408 Button Carbonated 4 Button Non-Carbonated 0 Pre-Mix 4H#3 4H#4 * 2H 2H * 950-145705 Button Carbonated 7 Button Non-Carbonated 0 Pre-Mix 2H 3HR 950-147507 Button Carbonated 5 Button Non-Carbonated 0 Pre-Mix 4H#3 3HR * 3HL * 2H * 950-144804 Button Carbonated 8 Button Non-Carbonated 0 Pre-Mix 2H 2H 3HR * 3HL 4H#4 * * * 3HL 4H#4 * * * * 4H#3 * * = Carbonated Positions = Non-Carbonated Positions #H = See Chart on Page 12 for Part Number = Secondary Water Metering Screw Affects These Positions ® = Requires Soda/Water Button Foot (P.N. 265-0039/265-0040) Extensions Into Bottom Of Button Where Symbol Appears. 16 BUTTON PLATE CONFIGURATIONS 015 014 659-0015 8 BUTTON 6C/0NC 019 659-0014 10 BUTTON 5C/3NC, 6C/2NC, 8C/0NC 020 659-0019 12 BUTTON 6C/4NC, 7C/3NC 659-0020 14 BUTTON 6C/6NC, 8C/4NC PLEASE CONTACT CUSTOMER SERVICE FOR OTHER PLATE CONFIGURATIONS 17 ACCESSORIES 1 2 7 3 5 6 8 4 9 11 12 10 15 10 16 13 14 10 10 17 10 10 10 18 ACCESSORIES ITEM SCHROEDER PN 1 675-0017-SP 2 315-0016 3 265-0151 4 265-0152 5 208-5112-SP 6 265-0153 7 316-0004-SP 8 316-0003-SP 9 316-0005-SP 10 208-5010-SP 11 625-0065-SP 12 625-0066-SP 13 625-0067-SP 14 625-0068-SP 15 625-0069-SP 16 625-0070-SP 17 625-0071-SP 18 030-0017 ACCESSORIES PARTS LIST DESCRIPTION KIT, HOLSTER ASSY, W/SCREWS/BG, BLACK, 5/PK INSERT, HOLSTER, SHORT, BARGUN HOLSTER, BARGUN, BLACK DRIPTRAY, BARGUN, BLACK KIT, O-RING, 2-112, EPDM, 100/PK BRACKET, MOUNTING, BARGUN, BLACK SEPARATOR, BARGUN, 5/PK TOOL, INSERT/EXTRACTOR, O-RING, 5/PK TOOL, SHUTOFF, 5/PK KIT, O-RING, 2-010, EPDM, 100/PK KIT, FITTING ASSY, 3/8 BARB x 2.70"L, W/FLANGE, 25/PK KIT, FITTING ASSY, 3/8 BARB x 1.50"L, W/FLANGE, 25/PK KIT, FITTING ASSY, 1/4 BARB x 1.25"L, W/FLANGE, 25/PK KIT, FITTING ASSY, 1/2 BARB x 2.70"L, W/FLANGE, 25/PK KIT, FITTING ASSY, 1/2 BARB x 1.50"L, W/FLANGE, 25/PK KIT, FITTING ASSY, 1/4 BARB, ELBOW, W/FLANGE, 25/PK KIT, FITTING ASSY, 3/8 BARB, ELBOW, W/FLANGE, 25/PK DRAIN TUBE, BARGUN (NOT SHOWN) 19 HANDLE ASSEMBLY 1 2 3 45 6 16 24 23 22 21 20 20 10 11 12 13 14 15 16 17 18 19 7 8 9 HANDLE ASSEMBLY ITEM SCHROEDER PN 1 265-0039-SP 265-0040-SP 2 220-0012-SP 265-0229-SP 265-0223-SP 265-0205-SP 3 265-0196-SP 265-0202-SP 265-0009-SP 265-0089-SP 265-0092-SP 4 265-0007-SP 265-0083-SP 5 265-0004-SP 6 279-0014-SP 7 220-0009-SP 220-0015-SP 8 220-0010-SP 631-0028-SP 9 631-0010-SP 631-0023-SP 10 208-5008-SP 11 208-5003-SP 12 625-0040-SP 13 215-0001-SP 14 208-5007-SP 645-0065-SP 15 645-0011-SP 645-0068-SP 645-0071-SP 16 220-0001-SP 17 808-0018-SP 18 208-5003-SP 19 625-0001-SP 20 265-0194-SP 21 210-0006-SP 22 808-0388-SP 23 808-0278-SP 24 265-0001-SP BARGUN HANDLE PARTS LIST DESCRIPTION KIT, BUTTON, WATER, OVAL, 50/PK KIT, BUTTON, SODA, OVAL, 50/PK KIT, SCREW, 6-32 x .500, PH, PHD, SS, 50/PK KIT, PLATE, BUTTON, 3B, BLACK, 5/PK KIT, PLATE, BUTTON, 5B, BLACK, 5/PK KIT, PLATE, BUTTON, 6B, JUICE, BLACK, 5/PK KIT, PLATE, BUTTON, 8B, BLACK, 5/PK KIT, PLATE, BUTTON, 8B, JUICE, BLACK, 5/PK KIT, PLATE, BUTTON, 10B, BLACK, 5/PK KIT, PLATE, BUTTON, 12B, BLACK, 5/PK KIT, PLATE, BUTTON, 14B, BLACK, 5-PK KIT, ACTUATOR, SINGLE, 50/PK KIT, ACTUATOR, SINGLE, PREMIX, 50/PK KIT, ACTUATOR, WATER/SODA, 50/PK KIT, EXTENSION, ACTUATOR, WATER/SODA, 100/PK KIT, SCREW, 6-32 x 1.125, SL, FHD, SS, (3B, 5B, 10B), 100/PK KIT, SCREW, 6-32 x 1.562, SL, FHD, SS, (12B, 14B), 100/PK KIT, SCREW, 6-32 x .500, SL, FHD, SS 100/PK KIT, HEEL ASSY, HANDLE, 6B, BLACK, 5/PK KIT, HEEL ASSY, HANDLE, 10B, BLACK, 5/PK KIT, HEEL ASSY, HANDLE, 12/14B, BLACK, 5/PK KIT, O-RING, 2-008, EPDM, 100/PK KIT, O-RING, 2-003, EPDM, 100/PK KIT, STEM & O-RING ASSY, BARGUN, 25/PK KIT, SPRING, STEM, 25/PK KIT, O-RING, 2-007, EPDM, 100/PK KIT, PLATE ASSY, PLUNGER, RETAINER, 6B, BLACK, 5/PK KIT, PLATE ASSY, PLUNGER, RETAINER, 10B, BLACK, 5/PK KIT, PLATE ASSY, PLUNGER, RETAINER, 12B, BLACK, 5/PK KIT, PLATE ASSY, PLUNGER, RETAINER, 14B, BLACK, 5/PK KIT, SCREW, 6-32 x .375, 100 DEG FHP, 100/PK KIT, LABEL, PLATE, BOTTOM, 50/PK KIT, O-RING, 2-003, EPDM, 100/PK KIT, SCREW ASSY, WATER, BRIX, 25/PK KIT, BODY, NOZZLE, BLACK, 5/PK KIT, SEAL, HANDLE, 5/PK KIT, LABEL, DOMED, BG, RATTLER, 8/SHEET KIT, LABEL, TWIST-ON, BARGUN, 25/PK KIT, RETAINER, BUTTERFLY, 100/PK 21 MANIFOLD ASSEMBLY 2 3 1 4 7 22 6 5 MANIFOLD ASSEMBLY ITEM SCHROEDER PN 1 265-0076-SP 808-0054-SP 2 808-0061-SP 808-0071-SP 3 808-0361-SP 808-0384-SP 4 208-5010-SP 5 224-0019-SP 808-0055-SP 6 808-0063-SP 808-0064-SP 7 224-0018-SP BARGUN MANIFOLD PARTS LIST DESCRIPTION KIT, SCREW, SEPARATOR, 10/PK KIT, LABEL, HANDLE LAYOUT, 10B, 5/PK KIT, LABEL, HANDLE LAYOUT, 12B, 5/PK KIT, LABEL, HANDLE LAYOUT, 14B, 5/PK KIT, LABEL, HOUSING LAYOUT, 10B, COMPACT BG, 4/PK KIT, LABEL, HOUSING LAYOUT, 14B, COMPACT BG, 4/PK KIT, O-RING, 2-010, EPDM, 100/PK KIT, SCREW, 8-16 x .688, PH, FHD, PLS, SS, 100/PK KIT, LABEL, BUTTON LAYOUT, 10B, 5/PK KIT, LABEL, BUTTON LAYOUT, 12B, 5/PK KIT, LABEL, BUTTON LAYOUT, 14B, 5/PK KIT, SCREW, 8-16 x 1.125, PH, FHD, PLS, SS, 100/PK 23 FLOW CONTROL MODULE ASSEMBLY FLOW CONTROL MODULE ASSEMBLY 1 2 3 1 4 14 5 5 6 13 7 12 8 11 10 9 24 FLOW CONTROL MODULE ASSEMBLY BARGUN FLOW CONTROL MODULE PARTS LIST ITEM SCHROEDER PN DESCRIPTION 1 224-0005-SP KIT, SCREW, 6-19 x .375, PLASTITE, PH, PHD, 100/PK 808-0363-SP KIT, LABEL, SODA, VALVE, COMPACT BG, 16/SHEET 808-0364-SP KIT, LABEL, WATER, VALVE, COMPACT BG, 16/SHEET 808-0365-SP KIT, LABEL, S1, VALVE, COMPACT BG, 16/SHEET 808-0366-SP KIT, LABEL, S2, VALVE, COMPACT BG, 16/SHEET 808-0367-SP KIT, LABEL, S3, VALVE, COMPACT BG, 16/SHEET 808-0368-SP KIT, LABEL, S4, VALVE, COMPACT BG, 16/SHEET 2 808-0369-SP 808-0370-SP KIT, LABEL, S5, VALVE, COMPACT BG, 16/SHEET KIT, LABEL, S6, VALVE, COMPACT BG, 16/SHEET 808-0371-SP KIT, LABEL, S7, VALVE, COMPACT BG, 16/SHEET 808-0372-SP KIT, LABEL, S8, VALVE, COMPACT BG, 16/SHEET 808-0373-SP KIT, LABEL, S9, VALVE, COMPACT BG, 16/SHEET 808-0374-SP KIT, LABEL, S10, VALVE, COMPACT BG, 16/SHEET 808-0375-SP KIT, LABEL, S11, VALVE, COMPACT BG, 16/SHEET 808-0376-SP KIT, LABEL ,S12, VALVE, COMPACT BG, 16/SHEET 3 208-5111-SP KIT, O-RING, 2-111, EPDM, 100/PK 4 208-5107-SP KIT, O-RING, 2-107, EPDM, 100/PK 5 265-0759-SP KIT, RETAINER, COMPACT, CLIP, 1/4" FITTING, 50/PK 6 208-5014-SP KIT, O-RING, 2-014, EPDM, 100/PK 639-0060-SP VALVE ASSY, FC, LONG-OUTLET, SYRUP, COMPACT BG 639-0061-SP VALVE ASSY, FC, SHORT-OUTLET, SYRUP, COMPACT BG 7 639-0062-SP VALVE ASSY, FC, SODA, COMPACT BG 639-0063-SP VALVE ASSY, FC, WATER, COMPACT BG 639-0064-SP VALVE ASSY, FC, LONG-OUT, DIET, COMPACT BG 8 265-0771 265-0772 HOUSING, VALVES, 10B, COMPACT BG HOUSING, VALVES, 12/14B, COMPACT BG 9 265-0762 265-0766 PLATE, MOUNTING, 10B, W/INSERTS, COMPACT BG PLATE, MOUNTING, 12/14B, W/INSERTS, COMPACT BG 10 224-0020-SP KIT, SCREW, 8-16 x .250, PLASTITE, PH, PHD, 100/PK 11 808-0361-SP 808-0384-SP KIT, LABEL, HOUSING LAYOUT, 10B, COMPACT BG, 4/PK KIT, LABEL, HOUSING LAYOUT, 14B, COMPACT BG, 4/PK 12 625-0067-SP KIT, FITTING ASSY, 1/4 BARB x 1.25"L, W/FLANGE, 25/PK 13 208-5010-SP KIT, O-RING, 2-010, EPDM, 100/PK 14 208-5108-SP KIT, O-RING, 2-108, EPDM, 100/PK 25 MMEECCHHAANNIICCAL MMOODUULLEEAASSSSEEMMBBLYLY 1 2 1 3 14 4 5 5 6 13 12 7 8 11 10 9 26 MMECHANICAL MODULE ASSEMBLYY BARGUN MECHANICAL MODULE PARTS LIST ITEM SCHROEDER PN DESCRIPTION 1 224-0005-SP KIT, SCREW, 6-19 x .375, PLASTITE, PH, PHD, 100/PK 808-0363-SP KIT, LABEL, SODA, VALVE, COMPACT BG, 16/SHEET 808-0364-SP KIT, LABEL, WATER, VALVE, COMPACT BG, 16/SHEET 808-0365-SP KIT, LABEL, S1, VALVE, COMPACT BG, 16/SHEET 808-0366-SP KIT, LABEL, S2, VALVE, COMPACT BG, 16/SHEET 808-0367-SP KIT, LABEL, S3, VALVE, COMPACT BG, 16/SHEET 808-0368-SP KIT, LABEL, S4, VALVE, COMPACT BG, 16/SHEET 808-0369-SP KIT, LABEL, S5, VALVE, COMPACT BG, 16/SHEET 2 808-0370-SP KIT, LABEL, S6, VALVE, COMPACT BG, 16/SHEET 808-0371-SP KIT, LABEL, S7, VALVE, COMPACT BG, 16/SHEET 808-0372-SP KIT, LABEL, S8, VALVE, COMPACT BG, 16/SHEET 808-0373-SP KIT, LABEL, S9, VALVE, COMPACT BG, 16/SHEET 808-0374-SP KIT, LABEL, S10, VALVE, COMPACT BG, 16/SHEET 808-0375-SP KIT, LABEL, S11, VALVE, COMPACT BG, 16/SHEET 808-0376-SP KIT, LABEL ,S12, VALVE, COMPACT BG, 16/SHEET 3 208-5111-SP KIT, O-RING, 2-111, EPDM, 100/PK 4 208-5107-SP KIT, O-RING, 2-107, EPDM, 100/PK 5 265-0759-SP KIT, RETAINER, COMPACT, CLIP, 1/4" FITTING, 50/PK 6 208-5014-SP KIT, O-RING, 2-014, EPDM, 100/PK 639-0065-SP VALVE ASSY, MC, LONG-OUTLET, COMPACT BG 639-0066-SP VALVE ASSY, MC, SHORT-OUTLET, COMPACT BG 7 639-0068-SP VALVE ASSY, MECHANICAL, WATER, COMPACT BG 639-0069-SP VALVE ASSY, MECHANICAL, SODA, COMPACT BG 265-0771 HOUSING, VALVES, 10B, COMPACT BG 8 265-0772 HOUSING, VALVES, 12/14B, COMPACT BG 265-0762 PLATE, MOUNTING, 10B, W/INSERTS, COMPACT BG 9 265-0766 PLATE, MOUNTING, 12/14B, W/INSERTS, COMPACT BG 10 224-0020-SP KIT, SCREW, 8-16 x .250, PLASTITE, PH, PHD, 100/PK 808-0361-SP KIT, LABEL, HOUSING LAYOUT, 10B, COMPACT BG, 4/PK 11 808-0384-SP KIT, LABEL, HOUSING LAYOUT, 14B, COMPACT BG, 4/PK 12 625-0067-SP KIT, FITTING ASSY, 1/4 BARB x 1.25"L, W/FLANGE, 25/PK 13 208-5010-SP KIT, O-RING, 2-010, EPDM, 100/PK 14 208-5108-SP KIT, O-RING, 2-108, EPDM, 100/PK 27 MOUNTING PLATE SCREW PLACEMENT PATENT & PATENT PENDING NUMBERS UNITED STATES 7,658,006 8,109,413 8,123,079 8,336,736 8,387,829 8,418,888 8,479,954 8,770,442 8,807,395 8,814,003 9,840,406 D697,753 D717,590 D717,591 D717,592 D717,593 D786,616 D758,795 UNITED KINGDOM GB2468792 GB2474741 GB2476347 GB2480531 GB2480532 AUSTRALIA 346264, 346389, AU201912368S MEXICO 41390, 317084, 31399 EUROPE 2300353, 2336076, 002159194, RCD NO. 006408092-0001 28 NEW BAR GUN PART NUMBER FORMAT Bar Gun part numbers are formatted to capture all relevant information about a product so that it can be tracked manufacturing, sale, troubleshooting and warranty purposes. As of 01/01/19, the format for the Bar Gun part number will be as follows: The legacy part number will still be referenced in your order confirmation, packing lists, and invoices. 95 is a legacy component of the part number. All of Schroeder America's finished bar gun part numbers will start with "95", no matter their age. All serial number labeling for complete guns will show "950" as the model number. If/when necessary, a letter may be used in this position to designate a non-standard bar gun type where special This position represents the number of carbonated flavors/buttons on the bar gun. Numbers range from 0 through 10. For Juice Dispenser with 3/8" input fittings use "J" in place of the two digits. The first digit after the second dash represents the bar gun's sheath length. The final set of three digits represents the button plate configuration that will be used on the gun. 95 1 C 08 6 0 3 F 007 This digit represents the customer/bottler for which the bar gun is/was produced and, therefore, designates the bargun handle color scheme. The two digits in the first position after the first dash represent the total number of buttons on the finished bar gun and will range from 01 through 14. This position represents the number of non-carbonated flavors/buttons on the bar gun and range from 0 through 10. This letter identifies the control module type that will be included with the completed bar gun assembly NO. DESCRIPTION 1 Coca - Cola (Red) 2 General Beverage (Black) 3 Pepsi (Blue) 4 - 9 (OTHER) LETR DESCRIPTION B Marine Rattler C Rattler NO. DESCRIPTION 1 36" 3 48" 4 60" LETR DESCRIPTION F All Flow Control Moule M Fully Mechanical Control Module 952C - 0860 - 3F007 represents a General Beverage, Rattler Bar Dispenser with 8 Buttons. 6 buttons are for carbonated flavors and 0 buttons are for non-carbonated flavors. The unit has a 48" sheath and an all flow control module assembly. It uses button plate configuration 007. (Old PN 950-08600-1-01-48-007) 29Adobe PDF Library 15.0 Adobe InDesign 14.0 (Macintosh)