It is a manual when there is /NS2, /NS25 and /NF2 in the ... The YTA temperature transmitter and this manual use the ... 2016 2017 2018 2019 2020 2021 2022.
Instrument Procedures Manual 5Th Edition Pdf - Statutory Instrument Practice - Legislation.gov.uk
YTA610-DA1A2NB | Yokogawa | YTA610 Temperature Transmitter
User's Manual
YTA610 and YTA710 Temperature Transmitters (Hardware)
IM 01C50G01-01EN
IM 01C50G01-01EN
5th Edition
YTA610 and YTA710 Temperature Transmitters (Hardware)
Toc-1
IM 01C50G01-01EN 5th Edition
CONTENTS
1. Preface........................................................................................................ 1-1
Notes on the User's Manual............................................................................. 1-2
Notes on Safety and Modifications................................................................... 1-2
For Safe Use of Product................................................................................... 1-2
Warranty............................................................................................................ 1-3
Trademarks....................................................................................................... 1-3
Control of Pollution Caused by the Product...................................................... 1-4
2. Notes on Handling..................................................................................... 2-1
2.1
Nameplate........................................................................................................... 2-1
2.2
Transport............................................................................................................. 2-1
2.3
Storage................................................................................................................ 2-1
2.4
Choosing the Installation Location.................................................................. 2-1
2.5
Use of a Transceiver.......................................................................................... 2-2
2.6
Insulation Resistance Test and Withstand Voltage Test............................... 2-2
2.6.1 Insulation resistance test procedure................................................... 2-2
2.6.2 Withstand voltage test procedure....................................................... 2-3
2.7
Installation of Explosion Protected Type Transmitters................................. 2-4
2.7.1 ATEX Certification............................................................................... 2-4
2.7.2 IECEx Certification.............................................................................. 2-8
2.7.3 FM Certification................................................................................. 2-10
2.7.4 CSA Certification............................................................................... 2-11
2.7.5 Control Drawing................................................................................ 2-14
2.8
EMC Conformity Standards............................................................................ 2-30
2.9
Safety Requirement Standards ..................................................................... 2-30
3. Part Names and Functions....................................................................... 3-1
3.1
Part Names......................................................................................................... 3-1
3.2
Hardware Error Burnout and Hardware Write Protect Switch (HART/BRAIN)
.............................................................................................................................. 3-1
3.3
Integral Indicator Display Function................................................................. 3-2
3.4
Local Parameter Setting.................................................................................... 3-3
3.4.1 Local Parameter Setting (LPS) Overview........................................... 3-3
3.4.2 Parameters Configuration................................................................... 3-6
5th Edition: June 2019 (YK) All Rights Reserved, Copyright © 2016, Yokogawa Electric Corporation
IM 01C50G01-01EN
Toc-2
4. Installation.................................................................................................. 4-1
5. Wiring.......................................................................................................... 5-1
5.1
Notes on Wiring.................................................................................................. 5-1
5.2
Loop Construction............................................................................................. 5-1
5.3
Cable Selection.................................................................................................. 5-2
5.3.1 Input signal Cable Selection............................................................... 5-2
5.3.2 Output Signal Cable Selection............................................................ 5-2
5.4
Cable and Terminal Connections..................................................................... 5-2
5.4.1 Input Terminal Connections................................................................ 5-2
5.4.2 Output Terminal Connection............................................................... 5-3
5.5
Wiring Cautions................................................................................................. 5-4
5.6
Grounding........................................................................................................... 5-4
6. Maintenance............................................................................................... 6-1
6.1
General................................................................................................................ 6-1
6.2
Calibration.......................................................................................................... 6-1
6.2.1 Selection of Equipment for Calibration............................................... 6-1
6.2.2 Calibration Procedure......................................................................... 6-2
6.3
Disassembly and Assembly............................................................................. 6-2
6.3.1 Replacement of Integral Indicator....................................................... 6-3
6.4
Troubleshooting................................................................................................. 6-4
6.4.1 Basic Troubleshooting Flow................................................................ 6-4
6.4.2 Example of Troubleshooting Flow...................................................... 6-4
6.5
Integral Indicator and Error Display................................................................. 6-6
7. General Specifications............................................................................. 7-1
7.1
Standard Specifications.................................................................................... 7-1
7.1.1 YTA710............................................................................................... 7-1
7.1.2 YTA610............................................................................................... 7-7
7.2
Model and Suffix Codes.................................................................................. 7-12
7.3
Optional Specifications (YTA610 and YTA710)............................................. 7-13
7.4
Dimensions (YTA610 and YTA710)................................................................ 7-24
Revision Information
IM 01C50G01-01EN
1. Preface
The YTA temperature transmitter is fully factorytested according to the specifications indicated on the order. In order for the YTA temperature transmitter to be fully functional and to operate in an efficient manner, the manual must be carefully read to become familiar with the functions, operation, and handling of the YTA. This manual gives instructions on handling, wiring, installation, maintenance, and general specifications. To ensure correct use, please read this manual and following user's manuals.
Document No. IM 01C50G01-01EN IM 01C50G01-02EN*1 IM 01C50G01-01P *2
IM 01C50G01-01K *3
IM 01C50T01-02EN IM 01C50T02-02EN IM 01C50T03-02EN GS 01C50G01-01EN GS 01C50H01-01EN
Explanation
Hardware (This manual)
For NEPSI Certification (Option code: /NS2, /NS25 and /NF2
For Transmissor de Temperaturas YTA610 e YTA710 (Hardware) (Option code: /UF1, /US1 and /US15)
YTA610 and YTA710 Temperature Transmitters (Hardware) (Option code: /PF2, /PS2 and /PS25)
For HART protocol type
For FOUNDATION Fieldbus communication type
For BRAIN protocol type
YTA710 Temperature Transmitter
YTA610 Temperature Transmitter
<1. Preface>
1-1
WARNING
When using the transmitter in a Safety Instrumented System (SIS) application, refer to Appendix 1 in either IM 01C50T01-02EN for the HART protocol. The instructions and procedures in this section must be strictly followed in order to maintain the transmitter for this safety level.
These manuals can be downloaded from the website of Yokogawa or purchased from the Yokogawa representatives.
Website address: http://www.yokogawa.com/fld/
*1: It is a manual when there is /NS2, /NS25 and /NF2 in the additional specifications.
*2: It is a manual when there is /UF1, /US1 and /US15 in the additional specifications. This IM 01C50G01-01P is only in Portuguese.
*3: It is a manual when there is /PF2, /PS2 and /PS25 in the additional specifications. This IM 01C50G01-01K is only in Korean.
IM 01C50G01-01EN
Notes on the User's Manual
· This manual should be delivered to the end user. · This manual and the identification tag attached
on packing box are essential parts of the product; keep them in a safe place for future reference. · The information contained in this manual is subject to change without prior notice. · The information contained in this manual, in whole or part, shall not be transcribed or copied without notice. · In no case does this manual guarantee the merchant ability of the transmitter or its adaptability to a specific client need. · Should any doubt or error be found in this manual, submit inquiries to your local dealer. · No special specifications are contained in this manual. When products whose suffix code or optional codes contain code "Z" and an exclusive document is attached, please read it along with this manual. · Changes to specifications, structure, and components used may not lead to the revision of this manual unless such changes affect the function and performance of the transmitter.
Notes on Safety and Modifications
· This product is designed to be used by a person with specialized knowledge.
· Before handling the YTA, it is absolutely imperative that users of this equipment read and observe the safety instructions mentioned in each section of the manual in order to ensure the protection and safety of operators, the YTA itself and the system containing the transmitter. We are not liable for any accidents arising out of handling that does not adhere to the guidelines established in the safety instructions.
· No maintenance should be performed on explosionproof type temperature transmitters while the equipment is energized. If maintenance is required with the cover open, always first use a gas detector to check that no explosive gases are present.
· If the user attempts to repair or modify an explosionproof type transmitter and is unable to restore it to its original condition, damage to the explosionproof features result, leading to dangerous conditions. Contact your authorized Yokogawa Electric Corporation representative for repairs or modifications of an explosionproof type transmitter.
<1. Preface>
1-2
For Safe Use of Product
Please give your attention to the followings.
(a) Installation
· The instrument must be installed by an expert engineer or a skilled personnel. The procedures described about INSTALLATION are not permitted for operators.
· In case of high process temperature, care should be taken not to burn yourself because the surface of the case reaches a high temperature.
· All installation shall comply with local installation requirement and local electrical code.
(b) Wiring
· The instrument must be installed by an expert engineer or a skilled personnel. The procedures described about WIRING are not permitted for operators.
· Please confirm that voltages between the power supply and the instrument before connecting the power cables and that the cables are not powered before connecting.
(c) Maintenance
· Please do not carry out except being written to a maintenance descriptions. When these procedures are needed, please contact nearest YOKOGAWA office.
· Care should be taken to prevent the build up of drift, dust or other material on the display glass and name plate. In case of its maintenance, soft and dry cloth is used.
(d) Modification
Yokogawa will not be liable for malfunctions or damage resulting from any modification made to this instrument by the customer.
(e) Product Disposal
The instrument should be disposed of in accordance with local and national legislation/ regulations.
(f) Authorized Representative in EEA
In relation to the CE Marking, The authorized representative for this product in the EEA (European Economic Area) is: Yokogawa Europe B.V. Euroweg 2, 3825 HD Amersfoort,The Netherlands
IM 01C50G01-01EN
(g) Morocco conformity mark This conformity mark indicates that the product complies with Moroccan safety and EMC requirements.
Symbols used in this manual
The YTA temperature transmitter and this manual use the following safety related symbols and signals.
WARNING
Contains precautions to protect against the chance of explosion or electric shock which, if not observed, could lead to death or serious injury.
CAUTION
Contains precautions to protect against danger, which, if not observed, could lead to personal injury or damage to the instrument.
IMPORTANT
Contains precautions to be observed to protect against adverse conditions that may lead to damage to the instrument or a system failure.
NOTE
Contains precautions to be observed with regard to understanding operation and functions.
Some of the diagrams in this manual are partially omitted, described in writing, or simplified for ease of explanation. The screen drawings contained in the instruction manual may have a display position or characters (upper/lower case) that differ slightly from the full-scale screen to an extent that does not hinder the understanding of functions or monitoring of operation.
<1. Preface>
1-3
Warranty
· The warranty period of the instrument is written on the estimate sheet that is included with your purchase. Any trouble arising during the warranty period shall be repaired free of charge.
· Inquiries with regard to problems with the instrument shall be accepted by the sales outlet or our local dealer representative.
· Should the instrument be found to be defective, inform us of the model name and the serial number of the instrument together with a detailed description of nonconformance and a progress report. Outline drawings or related data will also be helpful for repair.
· Whether or not the defective instrument is repaired free of charge depends on the result of our inspection.
Conditions not eligible for chargeexempt repair.
· Problems caused by improper or insufficient maintenance on the part of the customer.
· Trouble or damage caused by mishandling, misusage, or storage that exceeds the design or specification requirements.
· Problems caused by improper installation location or by maintenance conducted in a nonconforming location.
· Trouble or damage was caused by modification or repair that was handled by a party or parties other than our consigned agent.
· Trouble or damage was caused by inappropriate relocation following delivery.
· Trouble or damage was caused by fire, earthquake, wind or flood damage, lightning strikes or other acts of God that are not directly a result of problems with this instrument.
Trademarks
· HART is a trademark of the FieldComm Group. · Registered trademarks or trademarks
appearing in this manual are not designated by a TM or ® symbol. · Other company names and product names used in this manual are the registered trademarks or trademarks of their respective owners.
IM 01C50G01-01EN
<1. Preface>
1-4
Control of Pollution Caused by the Product
This is an explanation for the product based on "Control of Pollution caused by Electronic Information Products" in the People's Republic of China.
IM 01C50G01-01EN
<2. Notes on Handling>
2-1
2. Notes on Handling
The YTA temperature transmitter is fully factorytested upon shipment. When the YTA is delivered, check the appearance for damage, and also check that the transmitter mounting parts shown in Figure 2.1 are included with your shipment. If "No Mounting Bracket" is indicated, no transmitter mounting bracket is included.
Bracket fastening bolt
U-bolt nut
Vertical pipe mounting bracket Spring washer
Spring washer
U-bolt
Horizontal pipe mounting bracket
Transmitter fastening bolt
Bracket fastening nut
U-bolt nut
Figure 2.1 Transmitter mounting parts
F0201.ai
2.1 Nameplate
The model name and configuration are indicated on the nameplate. Verify that the configuration indicated in the "Model and Suffix Code" in Chapter 7 is in compliance with the specifications written on the order sheet.
Figure 2.2 Name plate
F0202.ai
2.2 Transport
To prevent damage while in transit, leave the transmitter in the original shipping container until it reaches the installation site.
2.3 Storage
When an extended storage period is expected, observe the following precautions: 1. If at all possible, store the transmitter in
factoryshipped condition, that is, in the original shipping container. 2. Choose a storage location that satisfies the following requirements. · A location that is not exposed to rain or water. · A location subject to a minimum of vibration or impact. · The following temperature and humidity range is recommended. Ordinary temperature and humidity (25°C, 65%) are preferable. Temperature:
No Integral indicator 40 to 85°C With Integral indicator 30 to 80°C Humidity: 0 to 100% RH (at 40°C) 3. The performance of the transmitter may be impaired if stored in an area exposed to direct rain and water. To avoid damage to the transmitter, install it immediately after removal from shipping container. Follow wiring instructions in Chapter 5.
2.4 Choosing the Installation Location
Although the temperature transmitter is designed to operate in a vigorous environment, to maintain stability and accuracy, the following is recommended:
(1) Ambient Temperature
It is preferable to not to expose the instrument to extreme temperatures or temperature fluctuations. If the instrument is exposed to radiation heat a thermal protection system and appropriate ventilation is recommended.
(2) Environmental Requirements
Do not allow the instrument to be installed in a location that is exposed to corrosive atmospheric conditions. When using the instrument in a corrosive environment, ensure the location is well ventilated. The unit and its wiring should be protected from exposure to rainwater.
IM 01C50G01-01EN
(3) Impact and Vibration
It is recommended that the instrument be installed in a location that is subject to a minimum amount of impact and vibration.
2.5 Use of a Transceiver
IMPORTANT
Although the temperature transmitter is designed to resist influence from high frequency noise; use of a transceiver in the vicinity of installation may cause problems. Installing the transmitter in an area free from high frequency noise (RFI) is recommended.
2.6 Insulation Resistance Test and Withstand Voltage Test
CAUTION
(1) Overvoltage of the test voltage that is so small that it does not cause an dielectric breakdown may in fact deteriorate insulation and lower the safety performance; to prevent this it is recommended that the amount of testing be kept to a minimum.
(2) The voltage for the insulation resistance test must be 500 V DC or lower, and the voltage for the withstand voltage test must be 500 V AC or lower. Failure to heed these guidelines may cause faulty operation.
(3) For with a lighting protector (option code:/A), please remove the lightning protector from terminal at the test. In case of testing with the lightning protector, the voltage for the insulation resistance test must be 100V DC or lower, and the voltage for the withstand voltage test must be 100V AC or lower. Failure to heed these guidelines may cause faulty operation.
Follow the steps below to perform the test, the wiring of the transmission line must be removed before initiating testing.
<2. Notes on Handling>
2-2
2.6.1 Insulation resistance test procedure
Testing between the output terminal and input terminal
1. Lay transition wiring between the + terminal, the terminal, and the check terminal of the terminal box.
2. Lay wiring across terminals 1, 2, 3, 4, and 5 of the terminal box.
3. Connect the insulation resistance meter (with the power turned OFF) between the transition wiring of Steps 1 and 2 above. The polarity of the input terminals must be positive and that of the output terminals must be negative.
4. Turn the power of the insulation resistance meter ON and measure the insulation resistance. The duration of the applied voltage must be the period during which 100M or more is confirmed (or 20M if the unit is equipped with a lightning protector).
5. Upon completion of the test, remove the insulation resistance meter, connect a 100K resistor between the transition wiring, and allow the electricity to discharge. Do not touch the terminal with your bare hands while the electricity is discharging for more than 1 second.
Testing between the output terminal and grounding terminal
1. Lay transition wiring between the + terminal, the - terminal, and the check terminal of the terminal box, then connect an insulation resistance meter (with the power turned OFF) between the transition wiring and the grounding terminal. The polarity of the transition wiring must be positive and that of the grounding terminal must be negative.
2. Turn the power of the insulation resistance meter ON and measure the insulation resistance. The duration of the applied voltage must be the period during which 100M or more is confirmed (or 20M if the unit is equipped with a lightning protector).
3. Upon completion of the test, remove the insulation resistance meter, connect a 100K resistor between the transition wiring and the grounding terminal, and allow the electricity to discharge. Do not touch the terminal with your bare hands while the electricity is discharging for more than 1 second.
IM 01C50G01-01EN
Testing between the input terminal and grounding terminal
1. Lay transition wiring between terminals 1, 2, 3, 4 and 5 of the terminal box, and connect the insulation resistor (with the power turned OFF) between the transition wiring and the grounding terminal. The polarity of the transition wiring must be positive and that of the grounding terminal must be negative.
2. Turn the power of the insulation resistance meter ON and measure the insulation resistance. The duration of the applied voltage must be the period during which 100M or more is confirmed (or 20M if the unit is equipped with a lightning protector).
3. Upon completion of the test, remove the insulation resistance meter, connect a 100K resistor between the transition wiring and the grounding terminal, and allow the electricity to discharge. Do not touch the terminal with your bare hands while the electricity is discharging for more than 1 second.
2.6.2 Withstand voltage test procedure
Testing between the output terminal and the input terminal
1. Lay transition wiring between the + terminal, the terminal, and the check terminal of the terminal box.
2. Lay transition wiring between terminals 1, 2, 3, 4 and 5 of the terminal box.
3. Connect the withstand voltage tester (with the power turned OFF) between the transition wiring shown in Steps 1 and 2 above.
4. After setting the current limit value of the withstand voltage tester to 10mA, turn the power ON, and carefully increase the impressed voltage from 0V to the specified value.
5. The voltage at the specified value must remain for a duration of one minute.
6. Upon completion of the test, carefully reduce the voltage so that no voltage surge occurs.
<2. Notes on Handling>
2-3
Testing between the output terminal and the grounding terminal
1. Lay the transition wiring between the + terminal, the - terminal and the check terminal of the terminal box, and connect the withstand voltage tester (with the power turned OFF) between the transition wiring and the grounding terminal. Connect the grounding side of the withstand voltage tester to the grounding terminal.
2. After setting the current limit value of the withstand voltage tester to 10mA, turn the power ON, and gradually increase the impressed voltage from 0V to the specified value.
3. The voltage at the specified value must remain for a duration of one minute.
4. Upon completion of the test, carefully reduce the voltage so that no voltage surge occurs.
Testing between the input terminal and the grounding terminal
1. Lay the transition wiring across terminals 1, 2, 3, 4, and 5 of the terminal box and connect the withstand voltage tester (with the power turned OFF) between the transition wiring and the grounding terminal. Connect the grounding side of the withstand voltage tester to the grounding terminal.
2. After setting the current limit value of the withstand voltage tester to 10mA, turn the power ON, and gradually increase the impressed voltage from 0V to the specified value.
3. The voltage at the specified value must remain for a duration of one minute.
4. Upon completion of the test, carefully reduce the voltage so that no voltage surge occurs.
IM 01C50G01-01EN
2.7 Installation of Explosion Protected Type Transmitters
In this section, further requirements and differences and for explosionproof type instrument are described. For explosionproof type instrument, the description in this chapter is prior to other description in this users manual.
CAUTION
To preserve the safety of explosionproof equipment requires great care during mounting, wiring, and piping. Safety requirements also place restrictions on maintenance and repair activities. Please read the following sections very carefully.
2.7.1 ATEX Certification
(1) Technical Data
a) ATEX intrinsically safe approval
Caution for ATEX intrinsically safe approval.
Note 1. Certification information 4 - 20mA type
· YTA610 and YTA710 with /KU2 temperature transmitter (4 - 20mA type) is applicable for use in hazardous locations.
[Intrinsically safe ia] · Applicable Standard:
EN 60079-0: 2012+A11:2013, EN 60079-11: 2012 · Certificate No. FM16ATEX0019X · Type of protection and marking code: II 1 G Ex ia IIC T5...T4 Ga · Ambient Temperature: 40 to 70°C for T4, 40 to 50°C for T5 · Enclosure: IP66/IP67 · Electrical parameters: Supply/Output circuit: Terminals: +, -
Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1,2,3,4,5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH · Dielectric strength: 500 V a.c.r.m.s.,1 min (See specific conditions of use)
<2. Notes on Handling>
2-4
[Intrinsically safe ic] · Applicable Standard:
EN 60079-0: 2012+A11:2013, EN 60079-11: 2012 · Certificate Not Applicable as per Annex VIII to ATEX 2014/34/EU · Type of protection and marking code: II 3 G Ex ic IIC T5...T4 Gc · Ambient Temperature: 30 to 70°C for T4, 30 to 50°C for T5 · Enclosure: IP66/IP67 · Overvoltage category: I · Electrical parameters: Supply/Output circuit: Terminals: +, -
Ui=30V, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1,2,3,4,5
Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH · Dielectric strength: 500 V a.c.r.m.s.,1 min (See specific conditions of use) Fieldbus type · YTA610 and YTA710 with /KU25 temperature transmitter (Fieldbus type) is applicable for use in hazardous locations. [Intrinsically safe ia] · Applicable Standard: EN 60079-0: 2012+A11:2013, EN 60079-11: 2012 · Certificate No. FM16ATEX0019X · Type of protection and marking code: II 1 G Ex ia IIC T4 Ga · Ambient Temperature: 55 to 60°C · Enclosure: IP66/IP67 · Electrical parameters: Supply/Output circuit: Terminals: +, FISCO field device or Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1,2,3,4,5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH · Dielectric strength: 500 V a.c.r.m.s.,1 min (See specific conditions of use) [Intrinsically safe ic ] · Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-11:2012 · Certificate Not Applicable as per Annex VIII to ATEX 2014/34/EU
IM 01C50G01-01EN
· Type of protection and marking code: II 3 G Ex ic IIC T4 Gc
· Ambient Temperature: 30 to 70°C · Enclosure: IP66/IP67 · Overvoltage category: I · Electrical parameters:
Supply/Output circuit: Terminals: +, FISCO field device or Ui=32V, Ci=2.2nF, Li=0mH
Sensor circuit: Terminals: 1,2,3,4,5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH
· Dielectric strength: 500 V a.c.r.m.s.,1 min (See specific conditions of use)
WARNING
Specification conditions of use · Electrostatic charges on the non-metallic parts (excluding glass parts) or coated parts of the Temperature Transmitter shall be avoided. · When the enclosure of the Temperature Transmitter is made of aluminum alloy, if it is mounted in an area where the use of Category 1G equipment is required, it must be installed such that, even in the event of rare incidents, an ignition source due to impact and/or friction sparks is excluded. · The dielectric strength of 500V r.m.s between the intrinsically safe circuit and the enclosure of the Temperature Transmitter is limited, only by the removable surge absorber F9220AR.
Note 2. Note for multiple types of protection (KU2 and KU25)
· For the installation of this transmitter, once a particular type of protection is selected, any other type of protection cannot be used. The installation must be in accordance with the description about the type of protection in this instruction manual. Cross out the unnecessary type of protection on the name plate in the following ways.
<2. Notes on Handling>
2-5
e.g. In case of selecting "ia" and crossing out "db" and "tb" and "ic"
e.g. In case of selecting "db" and "tb" and crossing out "ia" and "ic"
F0203.ai
Note 3. Installation Installation should be in accordance with Control Drawing IIE029-A63.
b) ATEX Flameproof Type and Dust Ignition Proof Type
Caution for ATEX Flameproof Type and Dust Ignition Proof Type
Note 1. Certificate information · YTA710 with /KF2, YTA610 and YTA710 with /KU2 and /KU25 temperature transmitters are applicable for use in hazardous locations. · No. KEMA 07ATEX0130 · Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-1:2014, EN 60079-31:2014 · Type of Protection and Marking Code: II 2 G Ex db IIC T6/T5 Gb, II 2 D Ex tb IIIC T70°C / T90°C Db · Ambient Temperature for Gas Atmospheres: 40 to 75°C (T6), 40 to 80°C (T5) · Ambient Temperature for Dust Atmospheres: 30 to 65°C (T70°C), 30 to 80°C (T90°C) · Degree of protection of enclosure: IP66/IP67 · Supply Voltage : 42 V dc max. (4 to 20 mA type) : 32 V dc max. (Fieldbus type) · Output Signal : 4 to 20 mA : 24 mA dc max. (Fieldbus type)
Note 2. Installation · Cable glands, adapters and/or blanking elements with a suitable IP rating shall be of Ex d IIC/Ex tb IIIC certified by ATEX and shall be installed so as to maintain the specific degree of protection (IP Code) of the equipment. · All wiring shall comply with local installation requirement.
IM 01C50G01-01EN
Note 3. Operation · Keep "WARNING" on the equipment as follows. WARNING: AFTER DE-ENERGIZING, DELAY 10 MINUTES BEFORE OPENING. WHEN THE AMBIENT TEMP.70°C, USE THE HEATRESISTING CABLES & CABLE GLANDS 90°C. POTENTIAL ELECTROSTATIC CHARGING HAZARD -SEE USER'S MANUAL · Take care not to generate mechanical spark when access to the instrument and peripheral devices in hazardous location.
Note 4. Special Conditions for Safe Use
WARNING
· Electrostatic charge may cause an explosion hazard. Avoid any actions that cause the generation of electrostatic charge, such as rubbing with a dry cloth on coating face of the product.
· If the YTA is mounted in an area where the use of Category 2D equipment is required, it shall be installed in such a way that the risk from electrostatic discharges and propagating brush discharges caused by rapid flow of dust is avoided.
· To satisfy IP66 or IP67, apply waterproof glands to the electrical connection port.
· If the equipment is affected by external sources of heating or cooling from plant facilities, make sure that the parts in contact with the equipment or in the near vicinity of the equipment do not exceed the ambient temperature range of the equipment.
Note 5. Maintenance and Repair · The instrument modification or parts replacement by other than authorized representative of Yokogawa Electric Corporation is prohibited and will void ATEX Flameproof Certification.
Note 6. Surge absorber · The surge absorber can be removed from, or added to the equipment.
<2. Notes on Handling>
2-6
(2) Electrical Connection
The type of electrical connection is stamped near the electrical connection port according to the following marking.
Screw Size ISO M20×1.5 female ANSI 1/2 NPT female
Marking M N
(3) Installation
Location of the marking
F0204.ai
WARNING
All wiring shall comply with local installation requirement and local electrical code.
(4) Operation
WARNING
· OPEN CIRCUIT BEFORE REMOVING COVER. INSTALL IN ACCORDANCE WITH THIS USER'S MANUAL
· Take care not to generate mechanical sparking when access to the instrument and peripheral devices in hazardous locations.
(5) Maintenance and Repair
WARNING
The instrument modification or parts replacement by other than authorized Representative of Yokogawa Electric Corporation is prohibited and will void the certification.
IM 01C50G01-01EN
(6) Name Plate YTA710 /KF2 Flameproof and Dust ignition proof type
No. KEMA 07ATEX0130 Ex db IIC T6/T5 Gb Ex tb IIIC T70°C/T90°C Db TEMP. CLASS T6/T5 Tamb (Gas) -40 to +75°C(T6)
-40 to +80°C(T5) (Dust) -30 to +65°C(T70°C)
-30 to +80°C(T90°C) ENCLOSURE: IP66/IP67
WARNING AFTER DE-ENERGIZING, DELAY 10 MINUTES BEFORE OPENING. WHEN THE AMBIENT TEMP.70°C, USE THE HEAT-RESISTING CABLES & CABLE GLANDS90°C. POTENTIAL ELECTROSTATIC CHARGING HAZARD -SEE USER' S MANUAL
<2. Notes on Handling>
2-7
Intrinsically safe approval and Flameproof and Dust ignition approval (Fieldbus type)
II 3 G
Ex ic IIC T4 Gc -30 Ta 70°C IP66/IP67 FISCO field device - - - - - - - - - - - - - - - - - - - - - - - - - Supply/Output: Ui=32V, Ci=2.2nF, Li=0mH Sensor: Uo=6.0V, Io=90mA, Po=135mW Co=10µF, Lo=3.9mH
WARNING WHEN THE AMBIENT TEMP.68°C, USE HEAT-RESISTING CABLES AND CABLE GLANDS75°C. POTENTIAL ELECTROSTATIC CHARGING HAZARD -SEE USERS MANUAL
F0205.ai
Intrinsically safe approval and Flameproof and Dust ignition approval (4 - 20 mA type)
II 3 G
Ex ic IIC T5...T4 Gc T4: -30 Ta 70°C T5: -30 Ta 50°C IP66/IP67 Supply/Output: Ui=30V, Ci=22nF, Li=0mH Sensor: Uo=6.0V, Io=90mA, Po=135mW Co=10µF, Lo=3.9mH
WARNING WHEN THE AMBIENT TEMP.68°C, USE HEAT-RESISTING CABLES AND CABLE GLANDS75°C. POTENTIAL ELECTROSTATIC CHARGING HAZARD -SEE USERS MANUAL
No. FM16ATEX0019X
II 1 G
No. KEMA 07ATEX0130
II 2 GD
Ex ia IIC T5...T4 Ga T4: -40 Ta 70°C T5: -40 Ta 50°C IP66/IP67 Supply/Output: Ui=30V, Ii=200mA, Pi=1.0W Ci=22nF, Li=0mH Sensor: Uo=6.0V, Io=90mA, Po=135mW Co=10µF, Lo=3.9mH
WARNING POTENTIAL ELECTROSTATIC CHARGING HAZARD -SEE USERS MANUAL
Ex db IIC T6/T5 Gb Ex tb IIIC T70°C/T90°C Db TEMP. CLASS T6/T5 Tamb (Gas) -40 to +75°C(T6)
-40 to +80°C(T5) (Dust) -30 to +65°C(T70°C)
-30 to +80°C(T90°C) ENCLOSURE: IP66/IP67
WARNING AFTER DE-ENERGIZING, DELAY 10 MINUTES BEFORE OPENING. WHEN THE AMBIENT TEMP.70°C, USE THE HEAT-RESISTING CABLES & CABLE GLANDS90°C. POTENTIAL ELECTROSTATIC CHARGING HAZARD -SEE USERS MANUAL
Cross out unnecessary marking other than the selected type of protection.
F0206.ai
II 1 G
II 2 GD
No. FM16ATEX0019X
No. KEMA 07ATEX0130
Ex ia IIC T4 Ga
Ex db IIC T6/T5 Gb
T4: -55 Ta 60°C
Ex tb IIIC T70°C/T90°C Db
IP66/IP67
TEMP. CLASS T6/T5
FISCO field device
Tamb (Gas) -40 to +75°C(T6)
Entity Parameters
-40 to +80°C(T5)
Supply/Output:
(Dust) -30 to +65°C(T70°C)
Ui=30V, Ii=300mA, Pi=1.2W
-30 to +80°C(T90°C)
Ci=2.2nF, Li=0mH
ENCLOSURE: IP66/IP67
Sensor:
Uo=6.0V, Io=90mA, Po=135mW
WARNING
Co=10µF, Lo=3.9mH
AFTER DE-ENERGIZING, DELAY
10 MINUTES BEFORE OPENING.
WARNING
WHEN THE AMBIENT TEMP.70°C,
POTENTIAL ELECTROSTATIC
USE THE HEAT-RESISTING
CHARGING HAZARD
CABLES & CABLE GLANDS90°C.
-SEE USERS MANUAL
POTENTIAL ELECTROSTATIC CHARGING
HAZARD -SEE USERS MANUAL
Cross out unnecessary marking other than the selected type of protection.
F0207.ai
MODEL: Specified model code. SUFFIX: Specified suffix code. STYLE: Style code. SUPPLY: Supply voltage. NO.: Serial number and year of production*1. OUTPUT: Output signal. FACTORY CAL: Specified calibration range.
TOKYO 180-8750 JAPAN: The manufacturer name and the address*2.
*1: The third figure from the left shows the production year. The relationship between the production year and the third figure is shown below.
The third figure S T U V W X Y
The year of Production
2016 2017 2018 2019 2020 2021 2022
For example, the production year of the product engraved in "NO." column on the name plate as follows is 2016.
C2S616294
The year 2016
*2: "180-8750" is a postal code which represents the following address.
2-9-32 Nakacho, Musashino-shi, Tokyo Japan
*3: The identification number of Notified Body.
IM 01C50G01-01EN
2.7.2 IECEx Certification
(1) Technical Data
a) IECEx intrinsically safe approval
Caution for IECEx intrinsically safe approval.
Note 1. Certification information 4 - 20mA type
· YTA610 and YTA710 with /SU2 temperature transmitter (4 - 20mA type) is applicable for use in hazardous locations.
· Applicable Standard: IEC 60079-0: 2011, IEC 60079-11: 2011
· Certificate No. IECEx FMG 16.0014X · Type of protection and marking code:
Ex ia IIC T5...T4 Ga Ex ic IIC T5...T4 Gc · Ambient Temperature: 40 to 70°C for T4, 40 to 50°C for T5 (Ex ia) 30 to 70°C for T4, 30 to 50°C for T5 (Ex ic) · Enclosure: IP66/IP67 · Overvoltage category: I · Electrial parameters (Ex ia): Supply/Output circuit: Terminals: +, -
Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH · Electrial parameters (Ex ic): Supply/Output circuit: Terminals: +, Ui=30V, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH · Dielectric strength: 500 V a.c.r.m.s.,1 min (See specific conditions of use) Fieldbus type · YTA610 and YTA710 with /SU25 temperature transmitter (Fieldbus type) is applicable for use in hazardous locations. · Applicable Standard: IEC 60079-0: 2011, IEC 60079-11: 2011 · Certificate No. IECEx FMG 16.0014X · Type of protection and marking code: Ex ia IIC T4 Ga Ex ic IIC T4 Gc · Ambient Temperature(Ex ia): 55 to 60°C · Ambient Temperature(Ex ic): 30 to 60°C · Enclosure: IP66/IP67 · Overvoltage category: I
<2. Notes on Handling>
2-8
· Electrical parameters (Ex ia): Supply/Output circuit: Terminals: +, FISCO field device or Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH
· Electrical parameters (Ex ic): Supply/Output circuit: Terminals: +, FISCO field device or Ui=30V, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH
· Dielectric strength: 500 V a.c.r.m.s.,1 min (See specific conditions of use)
WARNING
Specific conditions of use · Electrostatic charges on the non-metallic
parts (excluding glass parts) or coated parts of the Temperature Transmitter shall be avoided. · When the enclosure of the Temperature Transmitter is made of aluminum alloy, if it is mounted in an area where the use of EPL Ga equipment is required, it must be installed such that, even in the event of rare incidents, an ignition source due to impact and/or friction sparks is excluded. · The dielectric strength of 500 V r.m.s. between the intrinsically safe circuit and the enclosure of the Temperature Transmitter is limited, only by the removable surge absorber F9220AR.
Note 2. Note for multiple types of protection (SU2 and SU25)
· For the installation of this transmitter, once a particular type of protection is selected, any other type of protection cannot be used. The installation must be in accordance with the description about the type of protection in this instruction manual. Cross out the unnecessary type of protection on the name plate in the same ways of ATEX.
Note 3. Installation Installation should be in accordance with Control Drawing IIE029-A63.
IM 01C50G01-01EN
b) IECEx Flameproof Type and Dust Ignition Proof Type
Caution for IECEx flameproof type and Dust Ignition Proof Type
Note 1. Certification information · YTA710 with /SF2, YTA610 and YTA710 with /SU2 and /SU25 temperature transmitters are applicable for use in hazardous locations. · No. IECEx KEM 07.0044 · Applicable Standard: IEC 60079-0:2011, IEC 60079-1:2014-06, IEC 60079-31:2013 · Type of Protection and Marking Code: Ex db IIC T6/T5 Gb, Ex tb IIIC T70°C / T90°C Db · Ambient Temperature for Gas Atmospheres: 40 to 75°C (T6), 40 to 80°C (T5) · Ambient Temperature for Dust Atmospheres: 30 to 65°C (T70°C), 30 to 80°C (T90°C) · Enclosure: IP66/IP67 · Supply Voltage : 42 V dc max. (4 to 20 mA type) : 32 V dc max. (Fieldbus type) · Output Signal : 4 to 20 mA : 24 mA dc max. (Fieldbus type)
Note 2. Installation · Cable glands, adapters and/or blanking elements with a suitable IP rating shall be of Ex d IIC/Ex tb IIIC certified by IECEx and shall be installed so as to maintain the specific degree of protection (IP Code) of the equipment. · All wiring shall comply with local installation requirement.
Note 3. Operation · Keep strictly the "WARNING" on the label on the transmitter. WARNING: AFTER DE-ENERGIZING, DELAY 10 MINUTES BEFORE OPENING. WHEN THE AMBIENT TEMP.70°C, USE THE HEATRESISTING CABLES & CABLE GLANDS 90°C. POTENTIAL ELECTROSTATIC CHARGING HAZARD -SEE USER'S MANUAL · Take care not to generate mechanical spark when access to the instrument and peripheral devices in hazardous location.
<2. Notes on Handling> Note 4. Special Conditions for Safe Use
2-9
WARNING
· Electrostatic charge may cause an explosion hazard. Avoid any actions that cause the generation of electrostatic charge, such as rubbing with a dry cloth on coating face of the product.
· If the YTA is mounted in an area where the use of EPL Db equipment is required, it shall be installed in such a way that the risk from electrostatic discharges and propagating brush discharges caused by rapid flow of dust is avoided.
· To satisfy IP66 or IP67, apply waterproof glands to the electrical connection port.
· If the equipment is affected by external sources of heating or cooling from plant facilities, make sure that the parts in contact with the equipment or in the near vicinity of the equipment do not exceed the ambient temperature range of the equipment.
Note 5. Maintenance and Repair · The instrument modification or parts replacement by other than authorized representative of Yokogawa Electric Corporation is prohibited and will void IECEx Flameproof Certification.
Note 6. Surge absorber · The surge absorber can be removed from, or added to the equipment.
(2) Electrical Connection
The type of electrical connection is stamped near the electrical connection port according to the following marking.
Screw Size ISO M20×1.5 female ANSI 1/2 NPT female
Marking M N
Location of the marking
F0204.ai
IM 01C50G01-01EN
2.7.3 FM Certification
(1) Technical Data
a) FM (US) intrinsically safe approval/nonincendive approval
Caution for FM (US) intrinsically safe approval/nonincendive approval.
Note 1. Certification information 4 - 20mA type
· YTA610 and YTA710 with /FU1 temperature transmitter (4 - 20mA type) is applicable for use in hazardous locations.
· Applicable standard: FM Class 3600:2011, FM Class 3610:2015, FM Class 3611:2004, FM Class 3810:2005, ANSI/ISA-60079-0:2013, ANSI/ISA-60079-11:2014, ANSI/IEC 60529:2004, NEMA 250:2003
· Marking/Rating Intrinsically safe for Class I, II, III Division 1, Groups A, B, C, D, E, F, G, T5...T4 Class I, Zone 0 AEx ia IIC T5...T4 Non-incendive for Class I, II, Division 2, Groups A, B, C, D, F, G, T5...T4 Class III, Division 1 T5...T4 Class I, Zone 2 Group IIC T5...T4
· Ambient Temperature: 40 to 70°C for T4, 40 to 50°C for T5
· Enclosure Type 4X, IP66/IP67 · Electrical parameters:
Intrinsically safe for Supply/Output circuit: Terminals: +, Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH
Non-incendive for Supply/Output circuit: Terminals: +, Ui=30V, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH
· Dielectric strength: 500 V a.c.r.m.s.,1 min (See specific conditions of use)
<2. Notes on Handling>
2-10
Fieldbus type · YTA610 and YTA710 with /FU15 temperature transmitter (Fieldbus type) is applicable for use in hazardous locations. · Applicable standard: FM Class 3600:2011, FM Class 3610:2015, FM Class 3611:2004, FM Class 3810:2005, ANSI/ISA-60079-0:2013, ANSI/ISA-60079-11:2014, ANSI/IEC 60529:2004, NEMA 250:2003 · Marking/Rating Intrinsically safe for Class I, II, III Division 1 Groups A, B, C, D, E, F, G T4 Class I, Zone 0 AEx ia IIC T4 Non-incendive for Class I, II, Division 2, Groups A, B, C, D, F, G T4 Class III Division 1 T4 Class I Zone 2 Group IIC T4 · Ambient Temperature: 55 to 60°C · Enclosure Type 4X, IP66/IP67 · Electrical parameters: Intrinsically safe for Supply/Output circuit: Terminals: +, FISCO field device or Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Non-incendive for Supply/Output circuit: Terminals: +, Ui=32V, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH
· Dielectric strength: 500 V a.c.r.m.s.,1 min (See specific conditions of use)
IM 01C50G01-01EN
WARNING
Specific conditions of use · Electrostatic charges on the non-metallic parts (excluding glass parts) or coated parts of the Temperature Transmitter shall be avoided. · When the enclosure of the Temperature Transmitter is made of aluminum alloy, if it is mounted in Zone 0, it must be installed such that, even in the event of rare incidents, an ignition source due to impact and/or friction sparks is excluded. · The dielectric strength of 500 V r.m.s. between the intrinsically safe circuit and the enclosure of the Temperature Transmitter is limited, only by the removable surge absorber F9220AR.
Note 2. Note for multiple types of protection (FU1 and FU15)
· For the installation of this transmitter, once a particular type of protection is selected, any other type of protection cannot be used. The installation must be in accordance with the description about the type of protection in this instruction manual. Cross out the unnecessary type of protection on the name plate in the same ways of ATEX.
Note 3. Installation Installation should be in accordance with Control Drawing IIE029-A61.
b) FM Explosionproof Type
Caution for FM Explosionproof type
Note 1. Certification information · YTA710 with /FF1, YTA610 and YTA710 with /FU1 and /FU15 temperature transmitter are applicable for use in hazardous locations. · Applicable Standard: FM Class 3600: 2011, FM Class 3615: 2006, FM Class 3810: 2005, NEMA250: 2014 · Explosionproof for Class I, Division 1, Groups A, B, C, and D. · Dust-ignitionproof for Class II/III, Division 1, Groups E, F and G. · Enclosure rating: TYPE 4X. · Temperature Class: T6 · Ambient Temperature: 40 to 60°C · Supply Voltage: 42 V dc max. (4 to 20 mA type) : 32 V dc max. (Fieldbus type)
<2. Notes on Handling>
2-11
· Output Signal: 4 to 20 mA : 24 mA dc max. (Fieldbus type)
Note 2. Wiring · All wiring shall comply with National Electrical Code ANSI/NEPA70 and Local Electrical Codes. · "FACTORY SEALED, CONDUIT SEAL NOT REQUIRED".
Note 3. Operation · Keep strictly the "WARNING" on the nameplate attached on the transmitter. WARNING: OPEN CIRCUIT BEFORE REMOVING COVER. "FACTORY SEALED, CONDUIT SEAL NOT REQUIRED". AFTER DEENERGIZING, DELAY 2 MINUTES BEFORE OPENING. INSTALL IN ACCORDANCE WITH THE INSTRUCTION MANUAL IM 1C50G01-01EN. · Take care not to generate mechanical spark when access to the instrument and peripheral devices in hazardous location.
Note 4. Maintenance and Repair · The instrument modification or parts replacement by other than authorized representative of Yokogawa Electric Corporation is prohibited and will void Factory Mutual Explosionproof Approval.
2.7.4 CSA Certification
(1) Technical Data
a) FM (Canada) intrinsically safe approval/nonincendive approval
Caution for FM (Canada) intrinsically safe approval/ non-incendive approval.
Note 1. Certification information 4 - 20mA type
· YTA610 and YTA710 with /CU1 temperature transmitter (4 - 20mA type) is applicable for use in hazardous locations.
· Applicable standard: CAN/CSA-C22.2 No. 94.2-07, C22.2 No.213:1987, CAN /CSA-C22.2 No. 60079-0:11, CAN/CSA-C22.2 No. 60079-11:14, CAN/CSA-C22.2 No. 60529:05, CAN/CSA-C22.2 No. 61010-1-12, CAN/CSA-C22.2 No. 61010-2-030-12
IM 01C50G01-01EN
· Marking/Rating Intrinsically safe for Class I, II, III Division 1, Groups A, B, C, D, E, F, G, T5...T4 Ex ia IIC T5...T4 Ga Non-incendive for Class I, II, Division 2, Groups A, B, C, D, F, G, T5...T4 Class III, Division 1 T5...T4
· Ambient Temperature: 40 to 70°C for T4, 40 to 50°C for T5
· Enclosure Type 4X, IP66/IP67 · Electrical parameters:
Intrinsically safe for Supply/Output circuit: Terminals: +,Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH
Non-incendive for Supply/Output circuit: Terminals: +,Ui=30V, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH
· Dielectric strength: 500 V a.c.r.m.s.,1 min (See specific conditions of use)
Fieldbus type · YTA610 and YTA710 with /CU15 temperature transmitter (Fieldbus type) is applicable for use in hazardous locations. · Applicable standard: CAN/CSA-C22.2 No. 94.2-07, C22.2 No.213:1987, CAN /CSA-C22.2 No. 60079-0:11, CAN/CSA-C22.2 No. 60079-11:14, CAN/CSA-C22.2 No. 60529:05, CAN/CSA-C22.2 No. 61010-1-12, CAN/CSA-C22.2 No. 61010-2-030-12 · Marking/Rating Intrinsically safe for Class I, II, III Division 1, Groups A, B, C, D, E, F, G T4 Ex ia IIC T4 Ga Non-incendive for Class I, II, Division 2, Groups A, B, C, D, F, G T4 Class III, Division 1 T4
<2. Notes on Handling>
2-12
· Ambient Temperature: 55 to 60°C · Enclosure Type 4X, IP66/IP67 · Electrical parameters:
Intrinsically safe for Supply/Output circuit: Terminals: +, FISCO field device or Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH
Non-incendive for Supply/Output circuit: Terminals: +/Ui=32V, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH
· Dielectric strength: 500 V a.c.r.m.s.,1 min (See specific conditions of use)
WARNING
Specific conditions of use · Electrostatic charges on the non-metallic parts (excluding glass parts) or coated parts of the Temperature Transmitter shall be avoided. · When the enclosure of the Temperature Transmitter is made of aluminum alloy, if it is mounted in Zone 0, it must be installed such that, even in the event of rare incidents, an ignition source due to impact and/or friction sparks is excluded. · The dielectric strength of 500 V r.m.s. between the intrinsically safe circuit and the enclosure of the Temperature Transmitter is limited, only by the removable surge absorber F9220AR.
Note 2. Note for multiple types of protection (CU1 and CU15)
· For the installation of this transmitter, once a particular type of protection is selected, any other type of protection cannot be used. The installation must be in accordance with the description about the type of protection in this instruction manual. Cross out the unnecessary type of protection on the name plate in the same ways of ATEX.
IM 01C50G01-01EN
Note 3. Installation Installation should be in accordance with Control Drawing IIE029-A62.
b) CSA Explosionproof Type
Caution for CSA Explosionproof type
Note 1. Certification information · YTA710 with /CF1, YTA610 and YTA710 with /CU1 and /CU15 temperature transmitters are applicable for use in hazardous locations. · Certificate 1089576 · Applicable Standard: C22.2 No. 0-10, C22.2 No. 0.4-04, C22.2 No. 25-M1966, C22.2 No. 30-M1986, C22.2 No. 94-M1991, C22.2 No. 142-M1987, C22.2 No. 157-92, C22.2 No. 213-M1987, C22.2 No.61010-1-12, C22.2 No. 61010-2-030-12 · Class I, Groups B, C and D; · Class II, Groups E, F and G; · Class III. · Enclosure: TYPE 4X · Temperature Class: T6 · Ambient Temperature: 40 to 60°C · Supply Voltage: 42 V dc max. (4 to 20 mA type) : 32 V dc max. (Fieldbus type) · Output Signal: 4 to 20 mA : 24 mA dc max. (Fieldbus type)
<2. Notes on Handling>
2-13
Note 2. Wiring · All wiring shall comply with Canadian Electrical Code Part I and Local Electrical Codes. · In hazardous location, wiring shall be in conduit as shown in the figure. WARNING: A SEAL SHALL BE INSTALLED WITHIN 50 cm OF THE ENCLOSURE. UN SCELLEMENT DOIT ÊTRE INSTALLÉ À MOINS DE 50 cm DU BOÎTIER. · When installed in Division 2, "FACTORY SEALED, CONDUIT SEAL NOT REQUIRED".
Note 3. Operation · Keep strictly the "WARNING" on the label attached on the transmitter. WARNING: OPEN CIRCUIT BEFORE REMOVING COVER. AFTER DEENERGIZING, DELAY 2 MINUTES BEFORE OPENING. OUVRIR LE CIRCUIT AVANT D'ENLEVER LE COUVERCLE. APRÈS POWEROFF, ATTENDRE 2 MINUTES AVANT D'OUVRIR. · Take care not to generate mechanical spark when access to the instrument and peripheral devices in hazardous location.
Note 4. Maintenance and Repair · The instrument modification or parts replacement by other than authorized representative of Yokogawa Electric Corporation is prohibited and will void Canadian Standards Explosionproof Certification.
Sensor
Hazardous Locations Division 1 50 cm Max. YTA610 and YTA710 50 cm Max.
Sealing Fitting Certified/Listed Temperature Sensor
Conduit
Sealing Fitting
Sensor
Hazardous Locations Division 2 YTA610 and YTA710
Conduit Sealing Fitting Certified/Listed Temperature Sensor Note: Temperature sensor shall be certified in type of Hazardous Locations.
Non-hazardous Locations
Non-hazardous Location Equipment 42 V DC Max. 4 to 20 mA DC Signal
Non-hazardous Locations
Non-hazardous Location Equipment 42 V DC Max. 4 to 20 mA DC Signal
F0208.ai
IM 01C50G01-01EN
2.7.5 Control Drawing Control Drawing for ATEX and IECEx Ex ia
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A63
Page
01
<2. Notes on Handling>
Model
YTAxxx
Revision
1
Date
2017-08-18
Control Drawing (ATEX, IECEx) Intrinsically Safe Installation for YTAxxx J or D (Ex ia)
2-14
Hazardous Area
Hazardous Area
Non-Hazardous Area
Intrinsically Safe Apparatus or
Simple Apparatus
Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
- C
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx J or D Supply/Output: Ui = 30 V Ii = 200 mA Pi = 1.0 W Ci = 22 nF Li = 0 mH
Associated Apparatus
+
+
-
-
Linear source
IM 01C50G01-01EN
Control Drawing for ATEX and IECEx Ex ia
<2. Notes on Handling>
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A63
Page
02
Model
Revision
3
Intrinsically Safe Installation for YTAxxx F or G (Ex ia)
YTAxxx
Date
2017-08-18
Hazardous Area
Terminator
Hazardous Area Field Device
Terminator Field Device
Non-Hazardous Area
Associated Apparatus
+
+
-
-
Linear source or FISCO power supply
2-15
Intrinsically Safe Apparatus or
Simple Apparatus
Model YTAxxx F or G Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
-
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx F or G Supply/Output: Ui = 30 V Ii = 300 mA Pi = 1.2 W Ci = 2.2 nF Li = 0 mH
FISCO field device
Specific Condition of Use: Electrostatic charges on the non-metallic parts (excluding glass parts) or coated parts of
the Temperature Transmitter shall be avoided. (ATEX) When the enclosure of the Temperature Transmitter is made of aluminium alloy, if it is
mounted in a potentially explosive atmosphere requiring apparatus of equipment category 1 G is required, it must be installed such that, even in the event of rare incidents, an ignition source due to impact and/or friction sparks is excluded. (IECEx) When the enclosure of the Temperature Transmitters is made of aluminium alloy, if it is mounted in a potentially explosive atmosphere requiring apparatus of equipment EPL Ga is required, it must be installed such that, even in the event of rare incidents, an ignition source due to impact and/or friction sparks is excluded. The dielectric strength of 500 V r.m.s. between the intrinsically safe circuit and the enclosure of the Temperature Transmitter is limited, only by the removable surge absorber F9220AR.
WARNINGELECTROSTATIC CHARGE MAY CAUSE AN EXPLOSION HAZARD. AVOID ANY ACTIONS THAT CAUSE THE GENERATION OF ELECTROSTATIC CHARGE, SUCH AS RUBBING WITH A DRY CLOTH ON COATING FACE OF THE PRODUCT.
Note: The surge absorber F9220AR can be removed from, or added to the equipment.
IM 01C50G01-01EN
Control Drawing ATEX Ex ic
<2. Notes on Handling>
Yokogawa Electric Corporation
Title Control drawing
No. IKE061-A07
Page
01
Model
Revision
1
Intrinsically Safe Installation for YTAxxx J or D (Ex ic)
YTAxxx
Date
2017-12-27
2-16
Hazardous Area
Hazardous Area
Non-Hazardous Area
Intrinsically Safe Apparatus or
Simple Apparatus
Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
- C
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx J or D Supply/Output: Ui = 30 V Ci = 22 nF Li = 0 mH
Associated Apparatus
+
+
-
-
IM 01C50G01-01EN
Control Drawing ATEX Ex ic
<2. Notes on Handling>
Yokogawa Electric Corporation
Title Control drawing
No. IKE061-A07
Page
02
Model
Revision
0
Intrinsically Safe Installation for YTAxxx F or G (Ex ic)
Hazardous Area
Hazardous Area
Terminator
YTAxxx
Date
2017-12-27
Terminator
Non-Hazardous Area
Associated Apparatus
+
+
-
-
Field Device
Field Device
2-17
Intrinsically Safe Apparatus or
Simple Apparatus
Model YTAxxx F or G Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
-
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx F or G --------------FISCO field device --------------Supply/Output: Ui = 32 V Ci = 2.2 nF Li = 0 mH
Specific Condition of Use: Electrostatic charges on the non-metallic parts (excluding glass parts) or coated parts of
the Temperature Transmitter shall be avoided. The dielectric strength of 500 V r.m.s. between the intrinsically safe circuit and the enclosure of
the Temperature Transmitter is limited, only by the removable surge absorber F9220AR.
WARNING WHEN THE AMBIENT TEMP. 68°C, USE HEAT-RESISTING CABLES AND CABLE GLANDS 75°C
WARNING ELECTROSTATIC CHARGE MAY CAUSE AN EXPLOSION HAZARD. AVOID ANY ACTIONS THAT CAUSE THE GENERATION OF ELECTROSTATIC CHARGE, SUCH AS RUBBING WITH A DRY CLOTH ON COATING FACE OF THE PRODUCT.
Notes: The surge absorber F9220AR can be removed from, or added to the equipment. The equipment must be installed so that pollution degree 2 in accordance with EN 60664-1 is
maintained inside the enclosure. Cable glands, adapters and/or blanking elements shall be of Ex "n", Ex "e" or Ex "d" and shall
be installed so as to maintain the specified degree of protection (IP Code) according to the environmental conditions. IP must be at least IP54.
IM 01C50G01-01EN
Control Drawing IECEx Ex ic
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A63
Page
03
<2. Notes on Handling>
Model
YTAxxx
Revision
1
Date
2017-08-18
Control Drawing (IECEx) Intrinsically Safe Installation for YTAxxx J or D (Ex ic)
2-18
Hazardous Area
Hazardous Area
Non-Hazardous Area
Intrinsically Safe Apparatus or
Simple Apparatus
Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
- C
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx J or D Supply/Output: Ui = 30 V Ci = 22 nF Li = 0 mH
Associated Apparatus
+
+
-
-
Linear source
IM 01C50G01-01EN
Control Drawing IECEx Ex ic
<2. Notes on Handling>
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A63
Page
04
Model
Revision
0
Intrinsically Safe Installation for YTAxxx F or G (Ex ic)
YTAxxx
Date
2017-08-18
Hazardous Area
Terminator
Hazardous Area
Terminator
Non-Hazardous Area
Associated Apparatus
+
+
-
-
Field Device
Field Device
2-19
Intrinsically Safe Apparatus or
Simple Apparatus
Model YTAxxx F or G Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
-
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx F or G Supply/Output: Ui = 32 V Ci = 2.2 nF Li = 0 mH
FISCO field device
Specific Condition of Use: Electrostatic charges on the non-metallic parts (excluding glass parts) or coated parts of
the Temperature Transmitter shall be avoided. The dielectric strength of 500 V r.m.s. between the intrinsically safe circuit and the enclosure of the
Temperature Transmitter is limited, only by the removable surge absorber F9220AR.
WARNING WHEN THE AMBIENT TEMP. 68°C, USE HEAT-RESISTING CABLES AND CABLE GLANDS 75°C
WARNING ELECTROSTATIC CHARGE MAY CAUSE AN EXPLOSION HAZARD. AVOID ANY ACTIONS THAT CAUSE THE GENERATION OF ELECTROSTATIC CHARGE, SUCH AS RUBBING WITH A DRY CLOTH ON COATING FACE OF THE PRODUCT.
Notes: The surge absorber F9220AR can be removed from, or added to the equipment. The equipment must be installed so that pollution degree 2 in accordance with IEC 60664-1 is
maintained inside the enclosure. Cable glands, adapters and/or blanking elements shall be of Ex "n", Ex "e" or Ex "d" and shall be
installed so as to maintain the specified degree of protection (IP Code) according to the environmental conditions. IP must be at least IP54.
IM 01C50G01-01EN
<2. Notes on Handling> Control Drawing for FM (US) intrinsically safe approval (4 - 20 mA type)
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A61
Page
01
Model
Revision
1
Control Drawing (US)
Intrinsically Safe Installation for YTAxxx J or D
YTAxxx
Date
2017-08-18
Hazardous (Classified) Location
Hazardous (Classified) Location
Class I, Division 1, Groups A, B, C, D Class II, Division 1, Groups E, F, G Class III, Division 1 Class I, Zone 0, Group IIC
Class I, Division 1, Groups A, B, C, D Class II, Division 1, Groups E, F, G Class III, Division 1 Class I, Zone 0, Group IIC Temperature Class: T5...T4
Intrinsically Safe Apparatus or
Simple Apparatus
See Note 4
Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
- C
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx J or D Supply/Output: Ui = 30 V Ii = 200 mA Pi = 1.0 W Ci = 22 nF Li = 0 mH
Unclassified Location
Associated Apparatus
+
+
-
-
See Note 4
Linear source
2-20
IM 01C50G01-01EN
<2. Notes on Handling> Control Drawing for FM (US) Division 2 installation (4 - 20 mA type)
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A61
Page
02
Model
YTAxxx
Revision
1
Date
2017-08-18
Division 2 Installation for YTAxxx J or D
Hazardous (Classified) Location
Hazardous (Classified) Location
Unclassified Location
Class I, Division 2, Groups A, B, C, D Class II, Division 2, Groups F, G Class III, Division 1 Class I, Zone 2, Group IIC
Class I, Division 2, Groups A, B, C, D Class II, Division 2, Groups F, G Class III, Division 1 Class I, Zone 2, Group IIC Temperature Class: T5...T4
Intrinsically Safe Apparatus or
Simple Apparatus
See Note 4
Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
- C
Associated Apparatus
+
+
-
-
See Note 7
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx J or D Supply/Output: Ui = 30 V Ci = 22 nF Li = 0 mH
2-21
IM 01C50G01-01EN
<2. Notes on Handling> Control Drawing for FM (US) intrinsically safe approval (Fieldbus type)
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A61
Page
03
Model
Revision
1
Intrinsically Safe Installation for YTAxxx F or G
YTAxxx
Date
2017-08-18
Hazardous (Classified) Location
Class I, Division 1, Groups A, B, C, D Class II, Division 1, Groups E, F, G Class III, Division 1 Class I, Zone 0, Group IIC
Hazardous (Classified) Location
Class I, Division 1, Groups A, B, C, D Class II, Division 1, Groups E, F, G Class III, Division 1 Class I, Zone 0, Group IIC Temperature Class: T4
Terminator
Terminator
Intrinsically Safe Apparatus or
Simple Apparatus
See Note 4
Model YTAxxx F or G Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
-
Field Device
Field Device
Unclassified Location
Associated Apparatus
+
+
-
-
See Note 4
Linear source or FISCO power supply
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx F or G Supply/Output: Ui = 30 V Ii = 300 mA Pi = 1.2 W Ci = 2.2 nF Li = 0 mH
FISCO field device
2-22
IM 01C50G01-01EN
<2. Notes on Handling> Control Drawing for FM (US) Division 2 installation (Fieldbus type)
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A61
Page
04
Division 2 Installation for YTAxxx F or G
Model
YTAxxx
Revision
2
Date
2017-08-18
Hazardous (Classified) Location
Class I, Division 2, Groups A, B, C, D Class II, Division 2, Groups F, G Class III, Division 1 Class I, Zone 2, Group IIC
Hazardous (Classified) Location
Terminator
Class I, Division 2, Groups A, B, C, D Class II, Division 2, Groups F, G Class III, Division 1 Class I, Zone 2, Group IIC Temperature Class: T4
Unclassified Location
Terminator
Associated Apparatus
+
+
-
-
See Note 7
Field Device
Field Device
2-23
Intrinsically Safe Apparatus or
Simple Apparatus
See Note 4
Model YTAxxx F or G Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
-
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx F or G Supply/Output: Ui = 32 V Ci = 2.2 nF Li = 0 mH
IM 01C50G01-01EN
<2. Notes on Handling>
Control Drowing for FM (US) intrinsically safe approval/non-incendive approval (4 - 20 mA & Fieldbus type)
2-24
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A61
Page
05
Model
YTAxxx
Revision
1
Date
2017-08-18
Specific Conditions of Use: Electrostatic charges on the non-metallic parts (excluding glass parts) or coated parts of
the Temperature Transmitter shall be avoided. When the enclosure of the Temperature Transmitter is made of aluminum alloy, if it is mounted in
Zone 0, it must be installed such that, even in the event of rare incidents, an ignition source due to impact and/or friction sparks is excluded. The dielectric strength of 500 V r.m.s. between the intrinsically safe circuit and the enclosure of the Temperature Transmitter is limited, only by the removable surge absorber F9220AR.
Notes: 1. No revision to this drawing without prior approval of FM.
2. Installation must be in accordance with the National Electric Code (NFPA70), ANSI/ISA-RP12.06.01, and relevant local codes.
3. The Associated Apparatus must be FM-approved.
4. The following conditions must be satisfied for each circuit. Voc (or Uo) Ui Isc (or Io) Ii Po Pi Ca (or Co) Ci + Ccable La (or Lo) Li + Lcable
5. Control equipment connected to the Associated Apparatus must not use or generate a voltage more than Um of the Associated Apparatus.
6. The control drawing of the Associated Apparatus must be followed when installing the equipment.
7. In case Nonincendive Field Wiring Concept is used for the interconnection, FM-approved Associated Nonincendive Field Wiring Apparatus, which meets the following conditions, must be used as the Power Supply / Control Equipment. Voc (or Uo) Ui Ca (or Co) Ci + Ccable La (or Lo) Li + Lcable
8. The surge absorber F9220AR can be removed from, or added to the equipment.
9. Dust-tight conduit seals must be used when installed in Class II or Class III environments.
10. FISCO/FNICO installation must be in accordance with ANSI/ISA-60079-25. 11. The terminator(s) must be FM approved.
12. WARNING ELECTROSTATIC CHARGE MAY CAUSE AN EXPLOSION HAZARD. AVOID ANY ACTIONS THAT CAUSE THE GENERATION OF ELECTROSTATIC CHARGE, SUCH AS RUBBING WITH A DRY CLOTH ON COATING FACE OF THE PRODUCT.
13. WARNING SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY AND SUITABILITY FOR HAZARDOUS LOCATIONS
IM 01C50G01-01EN
<2. Notes on Handling> Control Drawing for FM (Canada) intrinsically safe approval (4 - 20mA type)
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A62
Page
01
Model
Revision
1
Control Drawing (Canada)
Intrinsically Safe Installation for YTAxxx J or D
YTAxxx
Date
2017-08-18
Hazardous Location
Hazardous Location
Non-Hazardous Location
Class I, Division 1, Groups A, B, C, D Class II, Division 1, Groups E, F, G Class III, Division 1
Class I, Division 1, Groups A, B, C, D Class II, Division 1, Groups E, F, G Class III, Division 1 Temperature Class: T5...T4
Intrinsically Safe Apparatus or
Simple Apparatus
See Note 3
Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
- C
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx J or D Supply/Output: Ui = 30 V Ii = 200 mA Pi = 1.0 W Ci = 22 nF Li = 0 mH
Associated Apparatus
+
+
-
-
See Note 3
Linear source
2-25
IM 01C50G01-01EN
<2. Notes on Handling> Control Drawing for FM (Canada) Division 2 installation (4 - 20 mA type)
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A62
Page
02
Division 2 Installation for YTAxxx J or D
Model
Revision
1
Hazardous Location
Hazardous Location
YTAxxx
Date
2017-08-18
Non-Hazardous Location
Class I, Division 2, Groups A, B, C, D Class II, Division 2, Groups F, G Class III, Division 1
Class I, Division 2, Groups A, B, C, D Class II, Division 2, Groups F, G Class III, Division 1 Temperature Class: T5...T4
Intrinsically Safe Apparatus or
Simple Apparatus
See Note 3
Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
- C
Associated Apparatus
+
+
-
-
See Note 6
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx J or D Supply/Output: Ui = 30 V Ci = 22 nF Li = 0 mH
2-26
IM 01C50G01-01EN
<2. Notes on Handling> Control Drawing for FM (Canada) intrinsically safe approval (Fieldbus type)
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A62
Page
03
Model
Revision
1
Intrinsically Safe Installation for YTAxxx F or G
YTAxxx
Date
2017-08-18
Hazardous Location
Class I, Division 1, Groups A, B, C, D Class II, Division 1, Groups E, F, G Class III, Division 1
Terminator
Hazardous Location
Class I, Division 1, Groups A, B, C, D Class II, Division 1, Groups E, F, G Class III, Division 1 Temperature Class: T4
Terminator
Field Device
Field Device
Non-Hazardous Location
Associated Apparatus
+
+
-
-
See Note 3
Linear source or FISCO power supply
2-27
Intrinsically Safe Apparatus or
Simple Apparatus
See Note 3
Model YTAxxx F or G Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
-
Sensor Input: Uo = 6.0 V Io = 90 mA Po = 135 mW Co = 10 F Lo = 3.9 mH
Model YTAxxx F or G Supply/Output: Ui = 30 V Ii = 300 mA Pi = 1.2 W Ci = 2.2 nF Li = 0 mH
FISCO field device
IM 01C50G01-01EN
<2. Notes on Handling> Control Drawing for FM (Canada) Division 2 installation (Fieldbus type)
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A62
Page
04
Division 2 Installation for YTAxxx F or G
Model
YTAxxx
Revision
2
Date
2017-08-18
Hazardous Location
Class I, Division 2, Groups A, B, C, D Class II, Division 2, Groups F, G Class III, Division 1
Terminator
Hazardous Location
Class I, Division 2, Groups A, B, C, D Class II, Division 2, Groups F, G Class III, Division 1 Temperature Class: T4
Terminator
Non-Hazardous Location
Associated Apparatus
+
+
-
-
See Note 6
Field Device
Field Device
2-28
Intrinsically Safe Apparatus or
Simple Apparatus
See Note 3
Model YTAxxx F or G Temperature Transmitter
Sensor Input
1 2 3 4 5
Supply/Output
+
-
Model YTAxxx F or G
Sensor Input: Supply/Output: Uo = 6.0 V Ui = 32 V Io = 90 mA Ci = 2.2 nF Po = 135 mW Li = 0 mH
Co = 10 F
Lo = 3.9 mH
IM 01C50G01-01EN
<2. Notes on Handling>
Control Drawings for FM (Canada) intrinsically safe approval/non-incendive approval (4 - 20 mA & Fieldbus type)
2-29
Yokogawa Electric Corporation
Title Control Drawing
No. IIE029-A62
Page
05
Model
YTAxxx
Revision
1
Date
2017-08-18
Specific Condition of Use: Electrostatic charges on the non-metallic parts (excluding glass parts) or coated parts of
the Temperature Transmitter shall be avoided. When the enclosure of the Temperature Transmitter is made of aluminum alloy, if it is mounted in
Zone 0, it must be installed such that, even in the event of rare incidents, an ignition source due to impact and/or friction sparks is excluded. The dielectric strength of 500 V r.m.s. between the intrinsically safe circuit and the enclosure of the Temperature Transmitter is limited, only by the removable surge absorber F9220AR.
Notes: 1. No revision to this drawing without prior approval of FM.
2. Installation must be in accordance with the Canadian Electrical Code Part I (C22.1), ANSI/ISA RP12.06.01, and relevant local codes.
3. The following conditions must be satisfied for each circuit. Voc (or Uo) Ui Isc (or Io) Ii Po Pi Ca (or Co) Ci + Ccable La (or Lo) Li + Lcable
4. Control equipment connected to the Associated Apparatus must not use or generate a voltage more than Um of the Associated Apparatus.
5. The control drawing of the Associated Apparatus must be followed when installing the equipment.
6. In case Nonincendive Field Wiring Concept is used for the interconnection, Nonincendive Field Wiring Apparatus, which meets the following conditions, must be used as the Power Supply / Control Equipment. Voc (or Uo) Ui Ca (or Co) Ci + Ccable La (or Lo) Li + Lcable
7. The surge absorber F9220AR can be removed from, or added to the equipment.
8. Dust-tight conduit seal must be used when installed in Class II and Class III environments.
9. FISCO/FNICO installation must be in accordance with CAN/CSA-C22.2 No. 60079-25.
10. WARNING ELECTROSTATIC CHARGE MAY CAUSE AN EXPLOSION HAZARD. AVOID ANY ACTIONS THAT CAUSE THE GENERATION OF ELECTROSTATIC CHARGE, SUCH AS RUBBING WITH A DRY CLOTH ON COATING FACE OF THE PRODUCT.
11. WARNING SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY AND SUITABILITY FOR HAZARDOUS LOCATIONS
IM 01C50G01-01EN
2.8 EMC Conformity Standards
EN61326-1 Class A, Table 2 EN61326-2-3 EN61326-2-5 (for Fieldbus) Immunity influence during the test: Output shift is specified within ±1% of full span.
CAUTION
This instrument is a Class A product, and it is designed for use in the industrial environment. Please use this instrument in the industrial environment only.
NOTE
YOKOGAWA recommends customer to apply the Metal Conduit Wiring or to use the twisted pair Shield Cable for signal wiring to conform the requirement of EMC Regulation, when customer installs the YTA Transmitter to the plant.
2.9 Safety Requirement Standards
EN61010-1, C22.2 No.61010-1 · Altitude of installation site: Max. 2,000 m above sea level · Installation category: I (Anticipated transient overvoltage 330 V) · Pollution degree: 2 · Indoor/Outdoor use
EN61010-2-030, C22.2 No.61010-2-030 · Measurement category: O(Other) (Measurement Input voltage: 150mVdc max)
<2. Notes on Handling>
2-30
IM 01C50G01-01EN
<3. Part Names and Functions>
3-1
3. Part Names and Functions
3.1 Part Names
Hardware error burnout direction switch Write protect switch
SW1
1
O BOUT
2
N WP
TEMP assembly
O-ring Name plate
Stud bolt
MAIN assembly Stud bolt
Terminal cover
Indicator assembly
Nut Amplifer cover
(HART/BRAIN)
Grounding terminal
Tag plate
Lock screw (for ATEX and IECEx flameproof type)
O-ring Integral indicator display
(FF)
Grounding terminal
Wiring connector (input signal side)
1
2 SW2
SIM O N
WP
Simulate enable switch Write lock switch
Output signal terminal
Wiring connector (output signal side)
Input signal terminal
Figure 3.1 Part Names
3.2 Hardware Error Burnout and Hardware Write Protect Switch (HART/BRAIN)
There are two slide switches on the MAIN assembly board. One sets the hardware error burnout direction, and the other sets a hardware write protection function which disables parameter changes through the use of a handheld terminal or some other communication method.
Lightning protector
F0301.ai
IM 01C50G01-01EN
The temperature transmitter is equipped with a hardware error burnout function used to set the output direction upon hardware error, and a sensor burnout function that sets the direction of the output in the event of burnout of the temperature sensor. When factory-shipped under standard specification or suffix code /C3, the output of both hardware error burnout and sensor burnout are set to HIGH, but if suffix code /C1 or /C2 is specified, the hardware error burnout is set to LOW (-5%) output, and sensor burnout is set to LOW (-2.5%) output, respectively. The setting of the direction of output from burnout can be changed.
To change the direction of output arising from burnout, set the swich on the MAIN assembly (see Figure 3.1 and Table 3.1). To change the direction of output arising out of sensor burnout, a dedicated hand-held terminal is required to rewrite the parameters within the transmitter.
For details, refer to the separate instruction manual, IM 01C50T01-02EN "HART Protocol" or IM 01C50T03-02EN "BRAIN Protocol".
NOTE
1. Turn off the power supply before changing the switches
2. To change the switches, it is necessary to remove the integral indicator assembly. Refer to " 6.3.1 Replacement of Integral Indicator" about the procedures.
Table 3.1
Burnout Direction and Hardware Write Protect Swich
Burnout direction (BOUT) and hardware write protect (WP) switch position Hardware error burnout direction Hardware error burnout output
Remark
Hardware write protect swich
SW1
1
O BOUT
2
N WP
SW1
1
O BOUT
2
N WP
HIGH
LOW
110% or more (21.6 mA DC)
-5% or less (3.2 mA DC)
Set to HIGH when standard Set to LOW when specification or suffix code /C1 or suffix code /C3 is /C2 is provided
provided
OFF Write enabled
ON Write disabled
<3. Part Names and Functions>
3-2
3.3 Integral Indicator Display Function
(1) Integral Indicator Display When Powering On
All segments display
Model name
Communication Protocol Communication Protocol
(HART or FF)
(BRAIN)
Device revision (HART or FF)
Software revision Process variable display
F0302.ai
IM 01C50G01-01EN
(2) Process Variable Display
Process variables that can be displayed in YTA are shown in the Table 3.2. A cycle of up to four displays can be shown by assigning variables to the parameters. Indicates values of process variables with the indication limits 99999 to 99999.
Table 3.2 Process Variable Display
Process variable Sensor1 Sensor1 - Terminal Terminal Sensor2 Sensor2 - Terminal Sensor1 - Sensor2 Sensor2 - Sensor1 Sensor Average Sensor Backup PV SV TV QV % of RANG mA of RANGE AI1 AI2 AI3 AI4
HART
BRAIN
F0303.ai
FF
3.4 Local Parameter Setting
WARNING
The local push button on the integral indicator must not be used in a hazardous area. When it is necessary to use the push button, operate it in a non- hazardous location.
<3. Part Names and Functions>
3-3
IMPORTANT
· Do not turn off the power to the temperature transmitter immediately after performing parameter setting. Powering off within 30 seconds of performing this procedure will return the parameter to its previous setting.
· LCD update will be slower at low ambient temperature, and it is recommended to use LPS function at temperatures above -10 degrees C.
· To implement local parameter settings, it is necessary to turn off the software Write protect and the hardware write protect switch on the MAIN assembly.
3.4.1 Local Parameter Setting (LPS) Overview
Parameter configuration by the 3 push button on the integral indicator offers easy and quick setup for parameters of Tag number, Unit, PV Damping, Display out 1, and etc. There is no effect on measurement signal (analog output or communication signal) when Local Parameter Setting is carried out.
Table 3.3 Action
Activate Move Edit Save
Cancel
Abort
Exit
Time out
Action
Operation
Push or button
Push or button
Push SET button
After parameter setting Push SET button "SAVE?" Push SET button "SAVED" If "FAILED" appear, retry or check the specificasions.
After parameter setting Push SET button "SAVE?" Push or button "CANCL?" Push SET button "CANCLD"
Hold down the SET button for over 2 seconds "ABORT" and move to the process measurement display
Push button (When the first parameter is selected) or Push button (When the last parameter is selected)
no operation for 10 minutes
IM 01C50G01-01EN
Table 3.4 Parameters List (HART)
Item Tag number Long tag number PV unit
PV damping time constant Sensor 1 type
Indicator Display TAG
LNG.TAG PV.UNIT
Write Mode RW RW RW
PV.DAMP
RW
S1.TYPE
RW
Sensor 1 wire
S1.WIRE
RW
Sensor 2 type
S2.TYPE
RW
Sensor 2 wire
S2.WIRE
RW
PV lower range
PV LRV
RW
PV upper range
PV URV
RW
Sensor burnout direction
BUN.DIR
RW
Sensor burnout value
BUN mA
RW
(mA)
Sensor burnout value
BUN %
RW
(%)
Display out 1
DISP.1
RW
Write protect
WRT.PRT
RW
Model
MODEL
R
HART revision
HART
R
Device revision
DEV.REV
R
Software revision
SW.REV
R
<3. Part Names and Functions>
3-4
Write Mode: RW=read/write, R=read only
Setting Type
Remarks
Character
up to 8 characters
Character
up to 32 characters
Selection
K, °C, °F, °R, mV, ohm, mA, %, NOUNIT
Numeric
0.00 to 100.00 seconds
Selection
Selection Selection Selection Numeric Numeric Selection
mv, ohm, Pt100, JPt100, Pt200, Pt500, Pt1000, Cu10, Ni120, TYPE.B, TYPE.E, TYPE.J, TYPE.K, TYPE.N, TYPE.R, TYPE.S, TYPE.T, TYPE.L, TYPE.U, TYPE.W3, TYPE.C, USR. TBL, NO.CNCT, S.MATCH 2, 3, 4 same as sensor1 type same as sensor1 wire
HIGH, LOW, USER, OFF
Numeric
3.6 to 21.6 mA
Numeric
-2.5 to 110%
Selection
Selection, Character
SENS.1, S.1-TER., TERM, SENS.2, S.2 - TER., S.1 - S.2, S2 - S.1, AVG, BACKUP, PV, SV, TV, QV, OUT %, OUT.mA
ON, OFF, Up to 8 Characters
Table 3.5 Parameters List (FF)
Item PD TAG Disp Out 1
Indicator Display PD.TAG DISP.1
Write Mode R RW
Local Write Lock
HW.LOCK
RW
Simulation Model Dev Rev Software Rev
HW SIM
RW
MODEL
R
DEV.REV.
R
SW.REV
R
Write Mode: RW=read/write, R=read only
Setting Type
Remarks
Selection
SENS.1, S.1-TER., TERM, SENS.2, S.2 - TER., S.1 - S.2, S2 - S.1, AVG, BACKUP, AI1.OUT, AI2.OUT, AI3.OUT, AI4.OUT
Selection, Character
ON, OFF, Up to 8 Characters
Selection
ON, OFF
IM 01C50G01-01EN
Table 3.6 Parameters List (BRAIN)
Item Tag number PV unit
PV damping time constant Sensor 1 type
Indicator Display TAG
PV.UNIT
Write Mode RW RW
PV.DAMP
RW
S1.TYPE
RW
Sensor 1 wire
S1.WIRE
RW
Sensor 2 type
S2.TYPE
RW
Sensor 2 wire
S2.WIRE
RW
PV lower range
PV LRV
RW
PV upper range
PV URV
RW
Sensor burnout direction
BUN.DIR
RW
Sensor burnout value
BUN mA
RW
(mA)
Sensor burnout value
BUN %
RW
(%)
Display out 1
DISP.1
RW
Write protect
WRT.PRT
RW
Model
MODEL
R
Software revision
SW.REV
R
<3. Part Names and Functions>
3-5
Write Mode: RW=read/write, R=read only
Setting Type
Remarks
Character
up to 16 characters
Selection
K, °C, °F, °R, mV, ohms, mA, %, NOUNIT
Selection
0,1,2,...,100 seconds
Selection
Selection Selection Selection Numeric Numeric Selection
TYPE.B, TYPE.E, TYPE.J, TYPE.K, TYPE.N, TYPE.R, TYPE.S, TYPE.T, TYPE.C, TYPE.W3, TYPE.L, TYPE.U, Pt100, Pt200, Pt500, Pt1000, JPt100, Ni120, Cu10, S.MATCH, ohms, mV, NO.CNCT 2, 3, 4 same as sensor1 type same as sensor1 wire
HIGH, LOW, USER, OFF
Numeric
3.6 to 21.6 mA
Numeric
-2.5 to 110%
Selection Selection, Character
PV, SV, TV, QV ON, OFF, Up to 8 Characters
IM 01C50G01-01EN
3.4.2 Parameters Configuration
(1) Activating Local Parameter Setting
Push the or button on the integral indicator to activate the local parameter setting mode. The transmitter will exit automatically from the local parameter setting mode if no operation is carried out for 10 minutes.
(2) Parameter Setting Review
As you press the button, you will be shown in the order of the Parameter list in each communication table. Press to back to previous Parameter. Press on the first Parameter or on the last Parameter to back to the process value display screen.
(3) Character Configuration
Character parameter Push SET button Change the first character by pushing / button Push SET button to go to the second character Change the second character by pushing / button Set all other characters in the same way Hold down the SET button "SAVE?" Push SET button "SAVED"
(4) Selection Configuration
Selection parameter Push SET button Use / button to select Push SET button "SAVE?" Push SET button "SAVED"
(5) Numeric Configuration
Numeric parameter Push SET button Change the first digit by pushing / button Push SET button to go to the second digit Change the second figure by pushing / button Set all other digits in the same way Hold down the SET button "SAVE?" Push SET button "SAVED"
Available numbers
Number of digits
Selection
Remarks
1 0, 1, 2, 3, 4, 5, 6, Determine plus and minus
7, 8, 9, -9, -8, -7, in the first digit. Return
-6, -5, -4, -3, -2, cannot be selected. In
-1, -0
case of integer a minus
cannot be selected.
2 to 5
0, 1, 2, 3, 4, 5, 6, A dot uses a one digit. 7, 8, 9, Dot(.), r* Two dots cannot use.
In case of integer a dot cannot be selected.
6 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, r*
*: Press the SET button at the time of r display, one digit will return.
<3. Part Names and Functions>
3-6
(6) Selection, Character Configuration
Select the Selection Character parameter to display the current status. Press the SET button to enter the character configuration. See 3. Character Configuration.
(7) Parameter Setting Lock
To disable parameter changes by the local parameter setting there are two different ways.
· Communication parameter write protect = On · Hardware write protection switch on MAIN
assembly = ON Reviewing local parameter setting by push button on the integral indicator is available at any time even when the local parameter setting is locked.
IM 01C50G01-01EN
4. Installation
IMPORTANT
· When performing on-site pipe fitting work that involves welding, use care to prevent outflow of the welding current into the transmitter.
· Do not use the transmitter as a foothold for installation.
Horizontal Pipe Mounting
· When using a horizontal pipe mounting bracket
<4. Installation>
4-1
· For details of choosing the installation location, refer to the guidelines outlined in Section 2.4, "Choosing the installation location".
· The mounting bracket shown in Figure 4.1 is used for the transmitter and is installed on 50A (2B) pipe. It can be installed either on a horizontal pipe and a vertical pipe or on a wall.
· To install the mounting bracket on the transmitter, torque the transmitter lock screw to about 20 to 30N·m.
Vertical Pipe Mounting
U-bolt nut Horizontal pipe mounting bracket Spring washer
Transmitter fastening bolt
U-bolt
· When using a vertical pipe mounting bracket
Wall Mounting
Bracket fastening bolt Vertical pipe mounting
bracket
Spring washer
Spring washer Transmitter fastening bolt
U-bolt nut
U-bolt
Bracket fastening nut
Figure 4.1 Mounting the Transmitter
Note: Wall mounting bolts are user-supplied.
F0401.ai IM 01C50G01-01EN
5. Wiring
5.1 Notes on Wiring
IMPORTANT
· Apply a waterproofing sealant to the threads of the connection port. (It is recommended that you use non-hardening sealant made of silicon resin for waterproofing.)
· Lay wiring as far away as possible from electrical noise sources such as large transformers, motors and power supplies.
· Remove the wiring connection dust-caps before wiring.
· To prevent electrical noise, the signal cable and the power cable must not be housed in the same conduit.
· The terminal box cover is locked by an Allen head bolt (a shrouding bolt) on ATEX and IECEx flameproof type transmitters. When the shrouding bolt is driven clockwise by an Allen wrench, it is going in and cover lock is released, and then the cove can be opened by hands. See Subsection 6.3 "Disassembly and Assembly" for details.
<5. Wiring>
5-1
5.2 Loop Construction
The YTA temperature transmitter is a two-wire temperature transmitter that uses the output power supply wiring and signal wiring alternately.
The transmission loop requires DC power. Connect the transmitter with the distributor as shown in Figure 5.1.
For the transmission loop, the load resistance of the distributor or other instrument to be installed in the loop and the lead wire must be within the range shown in Figure 5.2.
For details of communication requirements, refer to the additional reference materials, IM 01C50T0102EN "YTA610 and YTA710 Temperature Transmitter (HART Protocol)" and IM 01C50T0302EN "YTA710 Temperature Transmitter Functions (BRAIN Protocol)" .
<Hazardous location>
Input signal (thermocouple, RTD, mV, etc.)
<Nonhazardous location>
Distributor (power supply unit) Receiver +
Figure 5.1
Output signal
F0501.ai
Loop Construction (for General-use Type and Flameproof Type)
600
External load
resistance
R 250 ()
R=
E10.5 0.0244
Communication applicable range
for HART and BRAIN
Figure 5.2
10.5 16.6 25.2
42
Power supply voltage E (V DC)
F0502.ai
Relation Between Power Supply Voltage and External Load Resistance
Note: For intrinsic safe explosion-proof type units, the internal resistance of the safety barrier is also included in the load resistance.
IM 01C50G01-01EN
5.3 Cable Selection
5.3.1 Input signal Cable Selection
A dedicated cable is used for connection between the temperature sensor and the temperature transmitter. When a thermocouple is used as the temperature sensor, a compensation wire must be used that it appropriate for the type of thermocouple (refer to compensating cables for JIS C 1610/IEC60584-3 thermocouples). When a RTD is used as the temperature sensor, 2-core/3-core/4-core cable must be used (refer to JIS C 1604/IEC60751). The terminal of the dedicated cable is a 4 mm screw.
5.3.2 Output Signal Cable Selection
· With regard to the type of wire to be used for wiring, use twisted wires or cables with performance equivalent of 600V vinyl insulated cable (JIS C3307).
· For wiring in areas susceptible to electrical noise, use shielded wires.
· For wiring in high or low temperature areas, use wires or cables suitable for such temperatures.
· For use in an atmosphere where harmful gases or liquids, oil, or solvents are present, use wires or cables made of materials resistant to those substances.
· It is recommended that a self-sealing terminal with insulation sleeve (4-mm screw) be used for lead wire ends.
<5. Wiring>
5-2
5.4 Cable and Terminal Connections
5.4.1 Input Terminal Connections
NOTE
Turn off the power when installing the sensor. Please make sure that the sensor will not affect the host system in case not turning off the power.
NOTE
It is recommended that the terminals be connected in the order of STEP 1 and STEP 2.
CAUTION
When wiring, pay attention not to damage the cable and cores. All the cores of the cable must have the sufficient insulation around them.
STEP 1 (1)
a. Cable connection to RTD 3-wire
STEP 2 (2)
b. Output signal cable connection Figure 5.3 Terminal Connection Procedure
F0503.ai
IM 01C50G01-01EN
The temperature sensor is to be connected as shown in Figures 5.5.
Figure 5.4 Terminal Diagram
F0504.ai
Single input
1
2
(+)
3
()
4
5
1
(A)
2
3
(B)
4
5
Thermocouple and DC voltage
RTD and resistance (2-wire)
1
(A)
2
(B)
3
(B)
4
5
1
(A)
2
(A)
3
(B)
4
(B)
5
RTD and resistance RTD and resistance
(3-wire)
(4-wire)
Dual input
1
(+)
2
3
()
4
5
(+)
Thermocouple and DC voltage
1
(A1)
2
(B1) (B1)
3
4
(B2) (B2)
5
(A2)
RTD and resistance (3-wire)
1
(+)
2
()
3
(B2)
4
(B2)
5
(A2)
1
(A1)
2
(B1)
3
4
(B2)
5
(A2)
Thermocouple + RTD and resistance
(3-wire)
1
(A1) (B1)
2 (B1)
3
()
4
5
(+)
RTD and resistance (2-wire)
RTD and resistance (3-wire)
+ Thermocouple
F0505.ai
Figure 5.5 Wiring Connection Diagram
<5. Wiring>
5-3
5.4.2 Output Terminal Connection
(1) Connection of output signal/power supply cable
Connect the output signal cable (shared with the power supply cable) to the terminal and the + terminal. For details, refer to Figure 5.1, "Loop construction".
(2) Connection of wiring for field indicator
Connect the lead wire for the field indicator with the terminal and the C terminal.
Note: Use a field indicator with an internal resistance of 10 or less. Field indicator
Figure 5.6
Power + supply
+
Connection to Field Indicator
F0506.ai
(3) Connection of check meter
Connect the check meter with the terminal and the C terminal. The current signal of output signal 4 to 20 mA DC is output from the terminal and the C terminal.
Note: Use a check meter with internal resistance of 10 or less.
Check meter
Figure 5.7
Power + supply
Check Meter Connection
F0507.ai
IM 01C50G01-01EN
5.5 Wiring Cautions
(1) General-use Type and Intrinsically Safe Type
Use metal conduit wiring or a waterproof gland (metal wiring conduit JIS F 8801) for cable wiring.
· Apply nonhardening sealant to the threads of the wiring tap and a flexible fitting for secure waterproofing. Figure 5.8 shows an example of wiring on the output side. This example also applies to the wiring on the input side.
Flexible fitting
Wiring conduit
Apply a nonhardening sealant to the threads for waterproofing.
Tee Drain plug
F0508.ai
Figure 5.8 Example of Wiring Using a Wiring Conduit
(2) Flameproof Type
Wire cables through a flameproof packing adapter, or using a flameproof metal conduit.
· A seal fitting must be installed near the terminal box connection port for a sealed construction.
· Apply a nonhardening sealant to the threads of the terminal box connection port, flexible metal conduit and seal fitting for waterproofing.
Flameproof flexible metal conduit
Non-hazardous area
<5. Wiring>
5-4
5.6 Grounding
Grounding is always required for the proper operation of transmitters. Follow the domestic electrical requirements as regulated in each country. For a transmitter with a lightning protector, grounding should satisfy ground resistance of 10 or less.
Ground terminals are located on the inside and outside of the terminal box. Either of these terminals may be used.
CAUTION
To use an external arrester, carry out the interlocked grounding as shown below, and perform grounding work (ground resistance: 10 or less) in the arrester side.
Equipment
Arrester
F0510.ai
Grounding terminal (Inside)
Grounding terminal (Outside)
Figure 5.10 Grounding Terminal
F0511.ai
Gas sealing device
Hazardous area
Apply a nonhardening sealant to the threads of these fittings for waterproofing
Flameproof heavy-gauge steel conduit
Tee Drain plug
Seal fitting
After wiring, impregnate the fitting with a compound to seal tubing.
F0509.ai
Figure 5.9 Typical Wiring Using Flameproof Metal Conduit
IM 01C50G01-01EN
6. Maintenance
6.1 General
Each component of this instrument is configured in units to make maintenance easier.
This chapter contains disassembly and assembly procedures associated with calibration, adjustment and part replacement required for maintenance of the affected instrument.
IMPORTANT
1. Maintenance of this instrument should be performed in a service shop where the necessary tools are provided.
2. Handling the MAIN and Indicator assembly Some of the parts contained in the MAIN and Indicator assembly are susceptible to static electricity damage. Before performing maintenance, use a ground wrist band or other antistatic measures, and avoid touching the electronic components and circuits with bare hands.
<6. Maintenance>
6-1
6.2 Calibration
This instrument is fully factory-tested and is guaranteed for the intended accuracy, eliminating the need for calibration. When calibration needs to be varified, the following equipment and calibration procedure is recommended.
6.2.1 Selection of Equipment for Calibration
Table 6.1 lists the equipment required for calibration. The calibration equipment traceable to a verifying agency standard should be used.
Table 6.1 Calibration Equipment List
Name
Power supply
Recommended
SDBT, SDBS distributor
Load resistance
Voltmeter
2792 standard resistor (250 ±0.005%)
Universal calibrator
Variable resistor
279301 6-dial variable resistor (accuracy: ±(0.01% of rdg + 2m))
Remark 4 to 20mA DC (Output voltage: 26.5±1.5V DC, drop by internal 250 resistance included) For 4 to 20mA DC
For 4 to 20mA DC signal For calibration of DC voltage and thermocouple For calibration of RTD input
IM 01C50G01-01EN
6.2.2 Calibration Procedure
To conduct calibration required to evaluate the uncertainty while using the instrument, follow the steps below:
1. In accordance with the example wiring shown in Figure 6.1, connect each equipment, and warm up for 3 minutes or more. Lay wiring on the input side according to the sensor to be used.
a. Wiring of power supply and output + Output signal
Load
resistance
Voltmeter
b. Example of wiring for thermocouple or DC voltage input (when 1 input type is used)
1
2
(+)
3
()
4
5
DC voltage generator
c. Example of wiring for RTD 4-core type (when 1 input type is used)
1 2 3 4 5
Figure 6.1
(A) (A) (B) (B)
Variable resistor
F0601.ai
Example of Wiring for Calibration Equipment
2. For DC voltage input With a voltage generator, deliver input signals corresponding to 0, 25, 75, or 100% of the input span to the temperature transmitter. Measure the resulting input signal with the voltmeter (digital multimeter) and check the output value relative to the input value.
3. For thermocouple input Since this instrument is equipped with a reference junction compensating function, use a reference junction compensating function in universal calibrator in order to compensate for this function upon calibration. According to the reference millivolt table for thermocouple, obtain millivolt corresponding to 0, 25, 50, 75, or 100% of the span, and use that power as the input value, then deliver it from the universal calibrator to the temperature transmitter. Measure the resulting output signal with the voltage meter (digital multimeter) and check the output value relative to the input value.
<6. Maintenance>
6-2
4. RTD Using a RTD as input, calibration of the temperature transmitter is carried out via a 4-core wire connection. As defined the reference resistor value table of the RTD, obtain resistance values corresponding to 0, 25, 50, 75 or 100% of the span, and use the obtained resistance as the input value, then deliver it to the temperature transmitter by means of a variable resistor. Measure the resulting output signal with the voltmeter (digital multimeter) and check the output value relative to the input value.
5. In Steps 2 through 4, if the output signal deviates from the given range of accuracy when a given input signal is delivered, adjust the output using the handheld terminal. For details of how to adjust the output, refer to the additional reference, "HART Protocol" IM 01C50T01-02EN, or "BRAIN Protocol" IM 01C50T03-02EN and the instruction manual for each terminal.
6.3 Disassembly and Assembly
This section details the procedure for part replacement or disassembly and assembly of each component depending on the maintenance process.
Before starting disassembly and assembly work, turn off the power, and use a tool suited to the associated work.
Table 6.2 lists the tools required for disassembly and assembly of the instrument.
Table 6.2 Tools for Disassembly and Assembly
Tool name
Phillips screwdriver Standard screwdriver Hexagonal wrench Crescent wrench Torque wrench Box wrench Box screwdriver Forceps
Quantity
1 1 1 1 1 1 1 1
Remark For M10 screw
IM 01C50G01-01EN
CAUTION
Precautions for ATEX and IECEx Flameproof Type Transmitters
· For a withstand flameproof type transmitter, as a rule, move the transmitter to a nonhazardous location, then proceed with maintenance and restore the instrument to the original condition.
· For a withstand ATEX and IECEx flameproof type transmitter, turn the lock bolt (hexagon socket bolt) clockwise with a wrench for hexagon head, unlock and remove the cover. When installing the cover, it is the must to turn the lock bolt counterclockwise and lock the cover (locked to a torque of 0.7 Nm).
· For a withstand flameproof type transmitter, in no case should the user be allowed to modify the transmitter. Therefore, no user is allowed to add a integral indicator, or use the transmitter with the indicator removed. Contact us for any modification.
Terminal cover
TEMP assembly MAIN assembly Indicator assembly
Amplifer cover
Stud bolt
Lock screw (for ATEX and IECEx flameproof type)
Figure 6.2
Nut
F0602.ai
Mounting and Removal of Integral Indicator Assembly
<6. Maintenance>
6-3
6.3.1 Replacement of Integral Indicator
Removal of integral indicator
1. Remove the cover. 2. Remove two nuts while using your hand to
support the integral indicator. 3. Remove the indicator assembly from the
MAIN assembly. At this time, straighten and pull the indicator assembly forward so that the connector connecting the MAIN assembly and the indicator assembly is not damaged.
Mounting the Integral indicator
Integral Indicator can be installed in the following three directions.
Figure 6.3
F0603.ai
Installation Direction of Indicator
1. Place the Indicator assembly in desired direction over the MAIN assembly.
2. Align the mounting hole of the Indicator assembly with the stud bolt hole, and carefully insert the indicator into the connector in a straight manner so that the connector is not damaged.
3. Tighten the two nuts that secure the indicator. 4. Mount the cover.
IM 01C50G01-01EN
6.4 Troubleshooting
When the measured value is found abnormal, follow the troubleshooting flowchart below. If the complex nature of the trouble means that the cause cannot be identified using the following flowchart, refer the matter to our service personnel.
6.4.1 Basic Troubleshooting Flow
When the process measurement is found to be abnormal, it is necessary to determine whether the input temperature is out of range, the sensor has failed or being damaged, or the unit has been improperly wired. If it is suspected that the measurement system is the source of the problem, use the flowchart to identify the affected area and determine how to proceed.
In these troubleshooting steps, the self diagnostic function provides helpful solutions to the problem, refer to the instructions in Section 6.5 for details.
: Part supported by self-diagnosis
Measured value is found faulty
YES Inspect the process
Error in process
variable? NO
Error in measurement system
Faulty area in measurement
system
YES Inspect receiver
Receiver error NO
Environmental condition
Transmitter
Environmental condition: check, study, correction
Check the transmitter Operating requirements
Operating requirements: check, study, correction
Figure 6.4 Basic Flow and Self-diagnosis
F0604.ai
<6. Maintenance>
6-4
6.4.2 Example of Troubleshooting Flow
The following phenomena indicate that this instrument may be out of operation. [Example]
· No output signal is delivered. · Process variable changes but the output
signal remains unchanged. · The assessed value of the process variable
and the output are not coincident.
· If a integral indicator is attached, check the display of the error code.
· Connect a hand-held terminal and check self-diagnosis.
Was a faulty area found with self-
diagnosis?
YES
NO
Refer to the error code list and
check for recovery measures.
Is the polarity
NO
of the power supply
correct?
YES
Check the polarity between the power supply and terminal box and correct it.
Are the power supply voltage and load
NO
resistance correct?
YES
Refer to Section 5.2 and set the specified voltage and load resistance.
Is the sensor
NO
correctly connected?
YES
Check the sensor connection and correct it.
Is there a
disconnection in the loop?
NO
Do the loop numbers
correspond to the
counterpart?
YES
Check for disconnection or faulty wiring and take corrective measures.
Refer to our service personnel for details.
Figure 6.5
F0605.ai
Example of Troubleshooting Flow
IM 01C50G01-01EN
<6. Maintenance>
6-5
Table 6.3 Problems and Causes
Observed Problems Output fluctuates greatly.
Transmitter outputs fixed current.
Output is reversed. (See note 1) Parameters cannot be changed. Sensor backup function doesn't work correctly.
Output damping doesn't work.
Possible Cause Span is too narrow.
Input adjustment by user was not corrctly done. Output adjustment by user was not correctly done. The transmitter is in manual (test output) mode. Output adjustment by user was not correctly done. LRV is greater than URV.
The transmitter is in write protect status. Configuration of Sensor1 and Sensor2 is not correct.
Sensor backup mode is not enabled. Damping time constant is set to "0 second."
Related Parameter (HART)
PV LRV PV URV reset Sensor1(2) Trim reset AO Trim
exec Loop Test enable Dev Var Sim
reset AO Trim
PV LRV PV URV Write Protect
Sns1(2) Probe Type Sns1(2) Wire Status group2 Mask Status group3 Mask
PV is
AO Damping
Related Parameter (FF)
Sensor1 Trim Sensor2 Trim
SIM_ENABLE_MSG
WRITE_LOCK
SENSOR_TYPE_1(2) SENSOR_
CONNECTION_1(2) SENSOR_STATUS_
MASK_3 SENSOR_STATUS_
MASK_4
BACKUP_VALUE
PV_FTIME
Related Parameter (BRAIN)
E10:PV LRV E11:PV URV I16:S1 ADJ CLR I26:S2 ADJ CLR I33:OUT ADJ CLR
F10:OUTPUT MODE I30:OUTPUT
I33:OUT ADJ CLR
E10:PV LRV E11:PV URV G40:WRT PROTECT G41:WRT ENABLE D10:SENSOR1 TYPE D11:SENSOR1 WIRE D30:SENSOR2 TYPE D31:SENSOR2 WIRE K10:S1 FAIL MASK K11:S2 FAIL MASK K12:S1 SHRT MASK K13:S2 SHRT MASK K23:BKUP S1 MASK K24:BKUP S2 MASK B10:PV is
E20:AO DAMP
Note 1: If the reversed output is desired and necessary setting was done by user, it is not considered as a problem.
Table 6.4 Problems and Countermeasures
Observed Problems Output fluctuates greatly.
Transmitter outputs fixed current.
Output is reversed. (See note 1) Parameters cannot be changed. Sensor backup function doesn't work correctly.
Output damping doesn't work.
Possible Cause Span is too narrow.
Input adjustment by user was not corrctly done. Output adjustment by user was not correctly done. The transmitter is in manual (test output) mode. Output adjustment by user was not correctly done. LRV is greater than URV.
Countermeasure
Check the range, and change the settings to make the span larger.
Clear the user adjustment (Sensor trim) value or set it to off.
Clear the user adjustment (output trim) value or set it to off.
Release manual mode. (Make the transmitter return to Automatic Mode)
Clear the user adjustment (output trim) value or set it to off.
Set the correct value to URV and LRV.
The transmitter is in write protect status. Configuration of Sensor1 and Sensor2 is not correct.
Sensor backup mode is not enabled. Damping time constant is set to "0 second."
Release write protect.
· Check the type and wire settings for Sensor1 and Sensor2.
· Check the connection of Sensor1 and Sensor2.
Change PV mapping "Sensor Backup."
Set correct value.
Note 1: If the reversed output is desired and necessary setting was done by user, it is not considered as a problem.
IM 01C50G01-01EN
<6. Maintenance>
6-6
6.5 Integral Indicator and Error Display
For temperature transmitters equipped with an integral indicator, errors in the temperature sensor or the transmitter cause an integral indicator to call up the applicable error code. Table 6.5 lists the error codes for HART and BRAIN. Table 6.7 lists the error codes for Foundation fieldbus.
Table 6.5 List of Error Codes (HART and BRAIN)
Alarm Number
Indicator Message
AL.00 CPU.ERR
AL.01 AL.02 AL.03 AL.04*3 AL.05 AL.06 AL.07 AL.08
SENSOR TMP.MEM AD.CONV CAL.ERR CAL.ERR TMP.ERR COM.EEP TMP.MEM
AL.09 COM.ERR
AL.10 AL.11 AL.12*1 AL.13*1 AL.14*1 AL.15*1 AL.20 AL.21 AL.22*4
S.1.FAIL S.2.FAIL S.1.SHRT S.2.SHRT S.1.CORR S.2.CORR S.1.SGNL S.2.SGNL TERMNL
AL.23 S.1.FAIL
AL.24 AL.25 AL.26*1
S.2.FAIL DRIFT S.1.CYCL
AL.27*1 S.2.CYCL
AL.30 AL.31 AL.40 AL.41 AL.42 AL.43 AL.44 AL.45 AL.50
PV LO PV HI S.1 LO S.1 HI S.2 LO S.2 HI AMBNT.L AMBNT.H LRV LO
Cause
Output operation during error
MAIN CPU failed
Sensor non-volatile memory verifies alarm Non-volatile memory of the TEMP ASSY verify alarm Input circuit hardware failed MAIN ASSY memory failed TEMP ASSY memory failed TEMP ASSY voltage failed Communication non-volatile memory verifies alarm Non-volatile memory of the TEMP ASSY verifies alarm Internal communication failed
Sensor 1 failed or disconnected from terminal block Sensor 2 failed or disconnected from terminal block Sensor 1 short-circuited Sensor 2 short-circuited Sensor 1 corroded Sensor 2 corroded Sensor 1 input is out of measurable range. Sensor 2 input is out of measurable range. Terminal block temperature is abnormal. Or terminal block temperature sensor failed During sensor backup operation, Sensor1 fails, it has output Sensor2
During sensor backup operation, Sensor2 fails Sensor drift Temperature cycling times of Sensor1 exceeds the threshold Temperature cycling times of Sensor2 exceeds the threshold PV value is below the range limit setting PV value is above the range limit setting Measured temperature of sensor 1 is too low Measured temperature of sensor 1 is too high Measured temperature of sensor 2 is too low Measured temperature of sensor 2 is too high Ambient temperature is below-40 degree C Ambient temperature is above 85 degree C LRV setting is below the sensor operating temperature range
According to the transmitter failure output (burnout) Communacation disabled According to the transmitter failure output (burnout) Communication enabled
Continue to operate and output
According to the transmitter failure output (burnout) Communication enabled Refar table 6.6 Refar table 6.6 Refar table 6.6 Refar table 6.6 Continue to operate and output Continue to operate and output Continue to operate and output Continue to operate and output Refar table 6.6
Operating to the backup side. When the backup side also fails, output is according to burnout setting. Continue to operate and output Continue to operate and output Continue to operate and output
Continue to operate and output
Lower limit 3.68mA (-2%) Upper limit 20.8mA (105%) Continue to operate and output Continue to operate and output Continue to operate and output Continue to operate and output Continue to operate and output Continue to operate and output Continue to operate and output
IM 01C50G01-01EN
<6. Maintenance>
6-7
Alarm Number
Indicator Message
AL.51 LRV HI
AL.52 URV LO
AL.53 URV HI
AL.54 AL.60
SPAN.LO PV.CFG
AL.61*2 AL.62*2
S.1 CFG S.2 CFG
Cause
LRV setting is above the sensor operating temperature range URV setting is below the sensor operating temperature range URV setting is above the sensor operating temperature range It is set below recommended minimum span There is a setting error in the sensor that is mapped to the PV
There is a false set to sensor1 There is a false set to sensor2
Output operation during error Continue to operate and output
Continue to operate and output
Continue to operate and output
Continue to operate and output Hold the output of the previous error When it occurs at startup, hold at 4mA Continue to operate and output Continue to operate and output
*1: Applicable only for YTA710. *2: Applicable only for HART. *3: In software revision HART R1.03.01 or earlier or BRAIN R1.01.01, AL04 may be generated even when abnormality or
disconnection of the terminal block temperature sensor occurs. *4: In software revision HART R1.03.01 or earlier or BRAIN R1.01.01, even if abnormality or disconnection of the terminal block
temperature sensor occurs, AL22 may not be output and AL04 may be generated.
Table 6.6 Output operation (HART and BRAIN)
Current output mapping
SENS.1 S.1-TER TERM SENS.2 S.2-TER S.1-S.2 S.2-S.1 AVG BACKUP
S.1.FAIL
Sensor Burnout Sensor Burnout
*1
*1
*1
Sensor Burnout Sensor Burnout Sensor Burnout
*2
S.2.FAIL
*1
*1
*1
Sensor Burnout Sensor Burnout Sensor Burnout Sensor Burnout Sensor Burnout
*2
S.1.SHRT*3
Sensor Burnout Sensor Burnout
*1
*1
*1
Sensor Burnout Sensor Burnout Sensor Burnout
*2
S.2.SHRT*3
*1
*1
*1
Sensor Burnout Sensor Burnout Sensor Burnout Sensor Burnout Sensor Burnout
*2
TERMNL
*1*4
Sensor Burnout*4 Sensor Burnout*4
*1*4
Sensor Burnout*4
*1*4 *1*4 *1*4 *1*4
*1: Continue to operate and output. *2: When both sensor1 and sensor2 occur error, output is burnout. *3: Applicable only for YTA710. *4: In software revision HART R1.03.01 or earlier or BRAIN R1.01.01, fixed output value just before the alarm occurred.
IM 01C50G01-01EN
<6. Maintenance>
6-8
Table 6.7 List of Error Codes (FF)
Alarm Number AL.00 AL.01 AL.02 AL.03 AL.04 AL.05 AL.06 AL.07 AL.08 AL.09 AL.10 AL.11 AL.12*1 AL.13*1 AL.14*1 AL.15*1 AL.20 AL.21 AL.22
Indicator Message CPU.ERR SENSOR TMP.MEM AD.CONV CAL.ERR CAL.ERR TMP.ERR COM.EEP TMP.MEM COM.ERR S.1.FAIL S.2.FAIL S.1.SHRT S.2.SHRT S.1.CORR S.2.CORR S.1.SGNL S.2.SGNL TERMNL
AL.23 AL.24 AL.25 AL.26*1 AL.27*1 AL.40 AL.41 AL.42 AL.43 AL.44 AL.45 AL.61 AL.62 AL.100 AL.101 AL.101 AL.102 AL.102 AL.103 AL.103 AL.104 AL.104 AL.105 AL.105 AL.106 AL.106 AL.110 AL.111 AL.112 AL.113 AL.114 AL.115 AL.116
S.1.FAIL S.2.FAIL DRIFT S.1.CYCL S.2.CYCL S.1 LO S.1 HI S.2 LO S.2 HI AMBNT.L AMBNT.H S.1 CFG S.2 CFG NOT.RDY AI1 HH AI1 LL AI2 HH AI2 LL AI3 HH AI3 LL AI4 HH AI4 LL PID1.HH PID1.LL PID2.HH PID2.LL RS O/S STB O/S LTB O/S MTB O/S AI1 O/S AI2 O/S AI3 O/S
Cause
MAIN CPU failed Sensor non-volatile memory verifies alarm Non-volatile memory of the TEMP ASSY verifies alarm Input circuit hardware failed MAIN ASSY memory failed TEMP ASSY memory failed TEMP ASSY voltage failed Communication non-volatile memory verifies alarm Non-volatile memory of the TEMP ASSY verifies alarm Internal communication failed Sensor 1 failed or disconnected from terminal block Sensor 2 failed or disconnected from terminal block Sensor 1 short-circuited Sensor 2 short-circuited Sensor 1 corroded Sensor 2 corroded Sensor 1 input is out of measurable range. Sensor 2 input is out of measurable range. Terminal block temperature is abnormal. Such as abnormal or disconnection of the terminal block temperature sensor During sensor backup operation, Sensor1 fails, it has output Sensor2 During sensor backup operation, Sensor2 fails Sensor drift Temperature cycling times of Sensor1 exceeds the threshold Temperature cycling times of Sensor2 exceeds the threshold Measured temperature of sensor 1 is to low Measured temperature of sensor 1 is to high Measured temperature of sensor 2 is to low Measured temperature of sensor 2 is to high Ambient temperature is below-40 degree C Ambient temperature is above 85 degree C There is a false set to sensor1 There is a false set to sensor2 Any function block is not scheduled HI HI alarm occurs in AI1 block LO LO alarm occurs in AI1 block HI HI alarm occurs in AI2 block LO LO alarm occurs in AI2 block HI HI alarm occurs in AI3 block LO LO alarm occurs in AI3 block HI HI alarm occurs in AI4 block LO LO alarm occurs in AI4 block HI HI alarm occurs in PID1block LO LO alarm occurs in PID1 block HI HI alarm occurs in PID2 block LO LO alarm occurs in PID2 block The actual mode of the RS block is O/S. The actual mode of the STB block is O/S. The actual mode of the LTB block is O/S. The actual mode of the MTB block is O/S. The actual mode of the AI1 block is O/S. The actual mode of the AI2 block is O/S. The actual mode of the AI3 block is O/S.
IM 01C50G01-01EN
<6. Maintenance>
Alarm Number AL.117 AL.118 AL.119 AL.120 AL.121 AL.122 AL.130 AL.130 AL.130 AL.130 AL.131 AL.131 AL.131 AL.131 AL.132 AL.132 AL.132 AL.132 AL.133 AL.133 AL.133 AL.133 AL.134 AL.134 AL.134 AL.134 AL.135 AL.135 AL.135 AL.135 AL.136 AL.136 AL.136 AL.137 AL.137 AL.137 AL.138 AL.138 AL.138 AL.150 AL.151 AL.152 AL.153 AL.154 AL.155 AL.156 AL.157
Indicator Message AI4 O/S SCHEDL SCHEDL SCHEDL SCHEDL STB.MAN DI1 O/S DI1.MAN SCHEDL DI1.SIM DI2 O/S DI2.MAN SCHEDL DI2.SIM DI3 O/S DI3.MAN SCHEDL DI3.SIM DI4 O/S DI4.MAN SCHEDL DI4.SIM PID1.O/S PID.MAN SCHEDL PID.BYP PID2.O/S PID.MAN SCHEDL PID.BYP SC O/S SC MAN SCHEDL IS O/S IS MAN SCHEDL AR O/S AR MAN SCHEDL AI1.SIM AI2.SIM AI3.SIM AI4.SIM AI1.MAN AI2.MAN AI3.MAN AI4.MAN
Cause
The actual mode of the AI4 block is O/S. Execution of AI1 is not scheduled. Execution of AI2 is not scheduled. Execution of AI3 is not scheduled. Execution of AI4 is not scheduled. The actual mode of the STB block is Man. The actual mode of the DI1 block is O/S. The actual mode of the DI1 block is Man. Execution of DI1 is not scheduled. Simulate of the DI1 block is active. The actual mode of the DI2 block is O/S. The actual mode of the DI2 block is Man. Execution of DI2 is not scheduled. Simulate of the DI2 block is active. The actual mode of the DI3 block is O/S. The actual mode of the DI3 block is Man. Execution of DI3 is not scheduled. Simulate of the DI3 block is active. The actual mode of the DI4 block is O/S. The actual mode of the DI4 block is Man. Execution of DI4 is not scheduled. Simulate of the DI4 block is active. The actual mode of the PID1 block is O/S. The actual mode of the PID1 block is Man. Execution of PID1 is not scheduled. The bypass action for PID1 is active. The actual mode of the PID2 block is O/S. The actual mode of the PID2 block is Man. Execution of PID2 is not scheduled. The bypass action for PID2 is active. The actual mode of the SC block is O/S. The actual mode of the SC block is Man. Execution of SC is not scheduled. The actual mode of the IS block is O/S. The actual mode of the IS block is Man. Execution of IS is not scheduled. The actual mode of the AR block is O/S. The actual mode of the AR block is Man. Execution of AR is not scheduled. Simulate of the AI1 block is active. Simulate of the AI2 block is active. Simulate of the AI3 block is active. Simulate of the AI4 block is active. The actual mode of the AI1 block is Man. The actual mode of the AI2 block is Man. The actual mode of the AI3 block is Man. The actual mode of the AI4 block is Man.
*1: Applicable only for YTA710.
6-9
IM 01C50G01-01EN
<7. General Specifications>
7-1
7. General Specifications
7.1 Standard Specifications
7.1.1 YTA710
Performance Specifications
Accuracy HART and BRAIN communication type: A/D accuracy/span + D/A accuracy (See Table 7.1.) Fieldbus communication type: A/D accuracy (See Table 7.1.)
Cold Junction Compensation Accuracy (T/C) ±(0.32°C + 0.003 × |Tterm 23°C|) Tterm means the terminal temperature (40°C Tterm 85°C).
Ambient Temperature Effect (per 10°C change) See Table 7.2. for Standard type See Table 7.5. for /R1 option type
Stability (at 23±2°C) RTD: ±0.1% of reading or ±0.1°C per 2 years, whichever is greater. T/C: ±0.1% of reading or ±0.1°C per year, whichever is greater.
5 Year Stability (at 23±2°C) RTD: ±0.2% of reading or ±0.2°C, whichever is greater. T/C: ±0.4% of reading or ±0.4°C, whichever is greater.
Vibration Effect The YTA710 is tested to the following specifications with no effect on performance per IEC 60770-1 10 to 60 Hz : 0.21 mm peak displacement 60 to 2000 Hz : 3g
Power Supply Effect (HART and BRAIN Type) ±0.005% of calibrated span per volt
Functional Specifications
Input signals Input number: single and dual input Input type is selectable: Thermocouples, 2-, 3-, and 4-wire RTDs, ohms and DC millivolts. See Table 7.1.
Input signal source resistance (for T/C, mV) 1 k or lower
Input lead wire resistance (for RTD, ohm) 10 per wire or lower
Span & Range Limits See Table 7.1.
Output signals Two wire 4 to 20 mA DC Type Output range: 3.68 to 20.8 mA DC HART® or BRAIN protocol is superimposed on the 4 to 20 mA signal.
Fieldbus communication Type Output signal based on FOUNDATION fieldbusTM communication protocol.
Isolation Input/Output/GND isolated to 500V DC Except lightning protector option.
Manual Test Output Function The output value can be set manually.
Sensor Burnout (HART and BRAIN Type) High (21.6 mA DC) or Low (3.6 mA DC), user selectable.
Output in Transmitter Failure (HART and BRAIN Type) Down-scale: 5%, 3.2 mA DC or less (Optional code C1 or C2) Up-scale: 110%, 21.6 mA DC or more (Standard or Optional code C3)
IM 01C50G01-01EN
Update Time (HART and BRAIN Type) Approximately 0.5 seconds for a single sensor (0.8 second for dual sensors)
Turn-on Time (HART and BRAIN Type) Approximately 6 seconds for a single sensor (7 seconds for dual sensors)
Damping Time Constant Selectable from 0 to 100 seconds
Self-Diagnostics Self-diagnostic function based on the NAMUR NE107 standard detects failures.
Hardware-Diagnostics Hardware failure: Detect faiures in CPU, ADC, Memory, etc.
Sensor-Diagnostics Sensor failure: Detect the disconnection of sensor. Sensor short: Detect the short circuit of the sensor. Sensor Corrosion: Measure the loop resistance. Sensor line information: Measure the line resistance. Sensor drift: Detect the difference between sensor1 and sensor2. Temperature Cycle Diagnostics: Count the number of temperature fluctuations.
Fieldbus functions (Fieldbus Type) Functional specifications for Fieldbus communication conform to the standard specifications (H1) of FOUNDATION Fieldbus.
Function Block (Fieldbus Type)
Resource block The resource block contains physical transmitter information.
Transducer block The transducer block contains the actual measurement data and information about sensor type and configuration and diagnostics.
LCD display block The LCD display block is used to configure the local display, if an LCD display is being used.
<7. General Specifications>
7-2
Analog input (AI) Four independent AI blocks can be selected.
Digital input (DI) Four DI function blocks can be used as a limit switch for those temperature.
Other Function block As other Function blocks, Arithmetic (AR), Signal Characterizer (SC), Input Selector (IS), and two PID function blocks are available.
Function block AI DI SC IS AR PID
Execution time (ms) 30 30 30 30 30 45
Link master function This function enables backup of network manager and local control only by field devices.
Alarm function Fieldbus models securely support various alarm functions, such as High/Low alarm, notice of block error, etc. based on FOUNDATION fieldbus specifications.
Software download function This function permits to update YTA software via a FOUNDATION fieldbus. Based on Fundation fieldbus specifications (FF883) Download class: Class 1
EMC Conformity Standards EN61326-1 Class A, Table2 EN61326-2-3 EN61326-2-5 (for fieldbus type) Immunity influence during the test: Output shift is specified within ±1% of full span.
Functional Safety (HART Type) HART type is certified in compliance with IEC 61508: 2010. Functional Safety of Electrical/electronic/ programmable electronic related systems; SIL 2 capability for single transmitter use SIL 3 capability for dual transmitter use
IM 01C50G01-01EN
Safety Requirement Standards EN61010-1, C22.2 No.61010-1 · Altitude of installation site: Max. 2,000 m above sea level · Installation category: I (Anticipated transient overvoltage 330 V) · Pollution degree: 2 · Indoor/Outdoor use EN61010-2-030, C22.2 No.61010-2-030 · Measurement category: O (Other) (Measurement Input voltage: 150mVdc max)
EU RoHS Directive Applicable standard: EN 50581 Applicable production sites is shown below. The production sites of the RoHS compliant product are confirmed by the serial number shown in the frame of "NO." in the name plate of the product. Serial numbers (9 letters): NNYMnnnnn NN: Identification code of production site. Use "C2, U1, BH, Y3 or S5" Y: Year of production 2015: Use "R" 2016: Use "S" 2017: Use "T" 2018: Use "U" 2019: Use "V" M: Month of production January to September: Use "1" to "9" (January: 1, September: 9). October: Use "A". November: Use "B". December: Use "C". nnnnn: 5-digit number assigned sequentially in each production date by the production site.
<7. General Specifications>
7-3
Normal Operating Condition
(Optional features or approval codes may affect limits.)
Ambient Temperature Limits 40 to 85°C (40 to 185°F) 30 to 80°C (22 to 176°F) (with indicator model)
Ambient Humidity Limits 0 to 100% RH at 40°C (104°F)
Supply Voltage Requirements
HART and BRAIN Type 10.5 to 42 V DC for general use and flameproof type 10.5 to 32 V DC for lightning protector (option code /A) 10.5 to 30 V DC for intrinsically safe and non-incendive Minimum voltage limited at 16.6 V DC for digital communications HART and BRAIN With 24 V DC supply, up to a 550 load can be used. See graph below.
600
External load resistance
250 R ()
R=
E-10.5 0.0244
Digital Communication
range HART and BRAIN
Figure 7.1
10.5 16.6 25.2 Power supply voltage E (V)
42
F0701.ai
Relationship Between Power Supply Voltage and External Load Resistance
IM 01C50G01-01EN
Fieldbus Type 9 to 32V DC for general use, flameproof type, and non-incendive type 9 to 30 V DC for intrinsically safe type 9 to 17.5 V DC for FISCO field device Communication Requirements Supply Voltage: 9 to 32 V DC Current Draw: Steady state: 15 mA (max) Software download state: 24 mA (max)
Communication Requirements (BRAIN Type)
Communication Distance Up to 2 km (1.25 miles) when using CEV polyethylene-insulated PVC-sheathed cables. Communication distance varies depending on type of cable used.
Load Capacitance 0.22 F or less
Load Inductance 3.3 mH or less
Input Impedance of communicating device 10k or more at 2.4 kHz
Load Requirements (HART and BRAIN Type) 0 to 1290 for operation 250 to 600 for digital communication
<7. General Specifications>
7-4
Physical Specifications
Enclosure
Material & Coating · Low copper cast aluminum alloy [for aluminum housing] Polyester powder coating Mint-green paint (Munsell 5.6BG 3.3/2.9 or its equivalent) [for option code /P or /X2] Epoxy and polyurethane resin solvent coating · ASTM CF-8M Stainless steel
Degrees of Protection IP66/IP67, TYPE 4X
Name plate and tag 316 SST
Mounting Optional mounting brackets can be used either for two-inch pipe or flat panel mounting.
Terminal Screws M4 screws
Integral Indicator (with indicator model) 5-digit numerical display, 6-digit unit display and bar graph.
Local Parameter Setting (with indicator model) Parameter configuration by the push button offers easy and quick setup for parameters. Accessible parameters are different with each output signal cord.
Weight Alminum housing: 1.3 kg (2.9 lb) without integral indicator and mounting Integral indicator: 0.2 kg (0.4 lb) Bracket for horizontal pipe: 0.3 kg (0.7 lb) Bracket for vertical pipe: 1.0 kg (2.2 lb) Stainless housing: 3.1 kg (6.8 lb) without integral indicator and mounting Integral indicator: 0.3 kg (0.7 lb)
Connections Refer to "Model and Suffix Codes."
IM 01C50G01-01EN
<7. General Specifications>
7-5
Table 7.1 Sensor type, measurement range, and accuracy.
Sensor Type B E J K N
R
T/C
S
T
C
W3
L
U
RTD
Pt100 Pt200 Pt500 Pt1000 JPt100
Cu10
Ni120 mV ohm
Standard
IEC60584
ASTM E988 DIN43710 IEC60751
-- SAMA RC21-4
-- -- --
Measurement Range
°C
°F
100 to 300 300 to 1820
212 to 572 572 to 3308
-200 to -50 -50 to 1000
-328 to -58 -58 to 1832
-200 to -50 -50 to 1200
-328 to -58 -58 to 2192
-200 to -50 -50 to 1372
-328 to -58 -58 to 2501
-200 to -50 -50 to 1300
-328 to -58 -58 to 2372
-50 to 0 0 to 600 600 to 1768
-58 to 32 32 to 1112 1112 to 3214
-50 to 0 0 to 600 600 to 1768
-58 to 32 32 to 1112 1112 to 3214
-200 to -50 -50 to 400
-328 to -58 -58 to 752
0 to 400 400 to 1400 1400 to 2000 2000 to 2300
32 to 752 752 to 2552 2552 to 3632 3632 to 4172
0 to 400 400 to 1400 1400 to 2000 2000 to 2300
32 to 752 752 to 2552 2552 to 3632 3632 to 4172
-200 to -50 -50 to 900
-328 to -58 -58 to 1652
-200 to -50 -50 to 600
-328 to -58 -58 to 1112
-200 to 850
-328 to 1562
-200 to 850
-328 to 1562
-200 to 850
-328 to 1562
-200 to 300
-328 to 572
-200 to 500
-328 to 932
-70 to 150
-94 to 302
-70 to 320
-94 to 608
-10 to 120 [mV]
0 to 2000 []
Minimum Span
25°C (45°F)
10°C (18°F) 3 mV 20
Note 1: Note 2:
Total Accuracy = (A/D Accuracy / Span + D/A Accuracy). For Fieldbus type, accuracy = A/D Accuracy. For T/C input, add Cold Junction Compensation Error to the total accuracy. Example: when selecting Pt100 with measurement range of 0 to 200 °C 0.1°C / 200°C × 100% of span +0.02% of span = 0.07% of span T/C C type is same as W5 (ASTM E988).
A/D Accuracy
°C
°F
±3.0 ±0.75
±5.4 ±1.35
±0.35 ±0.16
±0.63 ±0.29
±0.25 ±0.20
±0.45 ±0.36
±0.5 ±0.25
±0.9 ±0.45
±0.4 ±0.35
±0.72 ±0.63
±1.0
±1.8
±0.6
±1.08
±0.4
±0.72
±1.0
±1.8
±0.5
±0.9
±0.4
±0.72
±0.25 ±0.14
±0.45 ±0.25
±0.7
±1.26
±0.5
±0.9
±0.7
±1.26
±0.9
±1.62
±0.8
±1.44
±0.5
±0.9
±0.6
±1.08
±0.9
±1.62
±0.3
±0.54
±0.2
±0.36
±0.35 ±0.25
±0.63 ±0.45
±0.1
±0.18
±0.22
±0.396
±0.14
±0.25
±0.1
±0.18
±0.1
±0.18
±1.0
±1.8
±0.08
±0.15
±0.012 [mV]
±0.35 []
D/A Accuracy
±0.02% of span
IM 01C50G01-01EN
<7. General Specifications>
Table 7.2 Temperature coefficient
Sensor Type
Thermocouples E, J, K, N, T, L, U
Thermocouples R, S, W3, C
Thermocouple B
100°C Reading < 300°C 300°C Reading
RTD
mV
ohm
Temperature Coefficient 0.08°C + 0.02% of abs.reading 0.25°C + 0.02% of abs.reading 1°C + 0.02% of abs.reading 0.5°C + 0.02% of abs.reading 0.08°C + 0.02% of abs.reading 0.002 mV + 0.02% of abs.reading 0.1 + 0.02% of reading
Note 1: Note 2:
Note 3:
The "abs.reading" for thermocouples and RTD means the absolute value of the reading in °C. Example of "abs.reading" When the temperature value is 250 Kelvin, "abs.reading" is 23.15. |250-273.15|= 23.15 Ambient Temperature Effect per 10 °C change is ±0.1% or ±(temperature coefficient/span), whichever is greater. Example of Ambient Temperature Effect Conditions:
1) Input Sensor: Pt100 2) Calibration Range: -100 to 100°C 3) Reading value: -50°C Ambient Temperature Effect per 10°C Temperature Coefficient/Span=(0.08°C+0.02/100×|-50°C|)/{100°C-(-100°C)}= 0.00045 0.045% Therefore, Ambient Temperature Effect is ±0.1%/10°C See Table 7.5 for R1 option type.
7-6
IM 01C50G01-01EN
7.1.2 YTA610
Performance Specifications
Accuracy HART communication type: A/D accuracy/span + D/A accuracy (See Table 7.3.) Fieldbus communication type: A/D accuracy (See Table 7.3.)
Cold Junction Compensation Accuracy ± 0.5°C (± 0.9 °F) for T/C only
Ambient Temperature Effect (per 10°C change) See Table 7.4.
Stability (at 23±2°C) RTD: ±0.1% of reading or ±0.1°C per 2 years, whichever is greater. T/C: ±0.1% of reading or ±0.1°C per year, whichever is greater.
5 Year Stability (at 23±2°C) RTD: ±0.25% of reading or ±0.25°C, whichever is greater. T/C: ±0.5% of reading or ±0.5°C, whichever is greater.
Vibration Effect The YTA610 is tested to the following specifications with no effect on performance per IEC 60770-1 10 to 60 Hz : 0.21 mm peak displacement 60 to 2000 Hz : 3g
Power Supply Effect (HART Type) ±0.005% of calibrated span per volt
Functional Specifications
Input signals Input number: single and dual input Input type is selectable: Thermocouples, 2-, 3-, and 4-wire RTDs, ohms and DC millivolts. See Table 7.3.
Input signal source resistance (for T/C, mV) 1 k or lower
Input lead wire resistance (for RTD, ohm) 10 per wire or lower
Span & Range Limits See Table 7.3.
<7. General Specifications>
7-7
Output signals Two wire 4 to 20 mA DC Type Output range: 3.68 to 20.8 mA DC HART® protocol is superimposed on the 4 to 20 mA signal.
Fieldbus communication Type Output signal based on FOUNDATION fieldbusTM communication protocol.
Isolation Input/Output/GND isolated to 500V DC Except lightning protector option.
Manual Test Output Function The output value can be set manually.
Sensor Burnout (HART Type) High (21.6 mA DC) or Low (3.6 mA DC), user selectable.
Output in Transmitter Failure (HART Type) Down-scale: 5%, 3.2 mA DC or less (Optional code C1 or C2) Up-scale: 110%, 21.6 mA DC or more (Standard or Optional code C3)
Update Time (HART Type) Approximately 0.5 seconds for a single sensor (0.8 second for dual sensors)
Turn-on Time (HART Type) Approximately 6 seconds for a single sensor (7 seconds for dual sensors)
Damping Time Constant Selectable from 0 to 100 seconds
Self-Diagnostics Self-diagnostic function based on the NAMUR NE107 standard detects failures.
Hardware-Diagnostics Hardware failure: Detect in CPU, ADC, Memory, etc.
Sensor-Diagnostics Sensor failure: Detect the disconnection of sensor. Sensor line information: Measure the line resistance. Sensor drift: Detect the difference between sensor1 and sensor2.
IM 01C50G01-01EN
Fieldbus functions (Fieldbus Type) Functional specifications for Fieldbus communication conform to the standard specifications (H1) of FOUNDATION Fieldbus.
Function Block (Fieldbus Type)
Resource block The resource block contains physical transmitter information.
Transducer block The transducer block contains the actual measurement data and information about sensor type and configuration and diagnostics.
LCD display block The LCD display block is used to configure the local display, if an LCD display is being used.
Analog input (AI) Four independent AI blocks can be selected.
Digital input (DI) Four DI function blocks can be used as a limit switch for those temperature.
Other Function block As other Function blocks, Arithmetic (AR), Signal Characterizer (SC), Input Selector (IS), and two PID function blocks are available.
Function block AI DI SC IS AR PID
Execution time (ms) 30 30 30 30 30 45
Link master function This function enables backup of network manager and local control only by field devices.
Alarm function Fieldbus models securely support various alarm functions, such as High/Low alarm, notice of block error, etc. based on FOUNDATION fieldbus specifications.
Software download function This function permits to update YTA software via a FOUNDATION fieldbus. Based on Fundation fieldbus specifications (FF883) Download class: Class 1
<7. General Specifications>
7-8
EMC Conformity Standards EN61326-1 Class A, Table2 EN61326-2-3 EN61326-2-5 (for fieldbus) Immunity influence during the test: Output shift is specified within ±1% of full span.
Functional Safety Hart communication type is certified in compliance with IEC 61508: 2010. Functional Safety of Electrical/electronic/ programmable electronic related systems; SIL 2 capability for single transmitter use SIL 3 capability for dual transmitter use
Safety Requirement Standards EN61010-1, C22.2 No.61010-1 · Altitude of installation site: Max. 2,000 m above sea level · Installation category: I (Anticipated transient overvoltage 330 V) · Pollution degree: 2 · Indoor/Outdoor use EN61010-2-030, C22.2 No.61010-2-030 · Measurement category: O (Other) (Measurement Input voltage: 150mVdc max)
EU RoHS Directive Applicable standard: EN 50581 Applicable production sites is shown below. The production sites of the RoHS compliant product are confirmed by the serial number shown in the frame of "NO." in the name plate of the product. Serial numbers (9 letters): NNYMnnnnn NN: Identification code of production site. Use "C2, U1, BH, Y3 or S5" Y: Year of production 2015: Use "R" 2016: Use "S" 2017: Use "T" 2018: Use "U" 2019: Use "V" M: Month of production January to September: Use "1" to "9" (January: 1, September: 9). October: Use "A". November: Use "B". December: Use "C". nnnnn: 5-digit number assigned sequentially in each production date by the production site.
IM 01C50G01-01EN
Normal Operating Condition
(Optional features or approval codes may affect limits.)
Ambient Temperature Limits 40 to 85°C (40 to 185°F) 30 to 80°C (22 to 176°F) (with indicator model)
Ambient Humidity Limits 0 to 100% RH at 40°C (104°F)
Supply Voltage Requirements
HART Type 10.5 to 42 V DC for general use and flameproof type 10.5 to 32 V DC for lightning protector (option code /A) 10.5 to 30 V DC for intrinsically safe and non-incendive Minimum voltage limited at 16.6 V DC for digital communications HART With 24 V DC supply, up to a 550 load can be used. See graph below.
600
External load resistance
250 R ()
R=
E-10.5 0.0244
Digital Communication
range HART
Figure 7.2
10.5 16.6 25.2 Power supply voltage E (V)
42
F0702.ai
Relationship Between Power Supply Voltage and External Load Resistance
Fieldbus Type 9 to 32V DC for general use, flameproof type, and non-incendive type 9 to 30 V DC for intrinsically safe type 9 to 17.5 V DC for FISCO field device Communication Requirements Supply Voltage: 9 to 32 V DC Current Draw: Steady state: 15 mA (max) Software download state: 24 mA (max)
Load Requirements (HART Type) 0 to 1290 for operation 250 to 600 for digital communication
<7. General Specifications>
7-9
Physical Specifications
Enclosure
Material & Coating · Low copper cast aluminum alloy [for aluminum housing] Polyester powder coating Mint-green paint (Munsell 5.6BG 3.3/2.9 or its equivalent) [for option code /P or /X2] Epoxy and polyurethane resin solvent coating · ASTM CF-8M Stainless steel
Degrees of Protection IP66/IP67, TYPE 4X
Name plate and tag 316 SST
Mounting Optional mounting brackets can be used either for two-inch pipe or flat panel mounting.
Terminal Screws M4 screws
Integral Indicator (with indicator model) 5-digit numerical display, 6-digit unit display and bar graph.
Local Parameter Setting (with indicator model) Parameter configuration by the push button offers easy and quick setup for parameters. Accessible parameters are different with each output signal cord.
Weight Alminum housing: 1.3 kg (2.9 lb) without integral indicator and mounting Integral indicator: 0.2 kg (0.4 lb) Bracket for horizontal pipe: 0.3 kg (0.7 lb) Bracket for vertical pipe: 1.0 kg (2.2 lb) Stainless housing: 3.1 kg (6.8 lb) without integral indicator and mounting Integral indicator: 0.3 kg (0.7 lb)
Connections Refer to "Model and Suffix Codes."
IM 01C50G01-01EN
<7. General Specifications>
7-10
Table 7.3 Sensor type, measurement range, and accuracy
Sensor Type B E J K N
R T/C
S T C
W3
L
RTD
U Pt100 Pt200 Pt500 Pt1000 JPt100
Cu10
Ni120 mV ohm
Standard
IEC60584
ASTM E988 DIN43710 IEC60751
-- SAMA RC21-4
-- -- --
Measurement Range
°C
°F
100 to 300 300 to 1820
212 to 572 572 to 3308
-200 to -50 -50 to 1000
-328 to -58 -58 to 1832
-200 to -50 -50 to 1200
-328 to -58 -58 to 2192
-200 to -50 -50 to 1372
-328 to -58 -58 to 2501
-200 to -50 -50 to 1300
-328 to -58 -58 to 2372
-50 to 0 0 to 600 600 to 1768
-58 to 32 32 to 1112 1112 to 3214
-50 to 0 0 to 1768
-58 to 32 32 to 3214
-200 to -50 -50 to 400
-328 to -58 -58 to 752
0 to 2000 2000 to 2300
32 to 3632 3632 to 4172
0 to 400 400 to 1400 1400 to 2000 2000 to 2300
32 to 752 752 to 2552 2552 to 3632 3632 to 4172
-200 to -50 -50 to 900
-328 to -58 -58 to 1652
-200 to 600
-328 to 1112
-200 to 850
-328 to 1562
-200 to 850
-328 to 1562
-200 to 850
-328 to 1562
-200 to 300
-328 to 1562
-200 to 500
-328 to 932
-70 to 150
-94 to 302
-70 to 320
-94 to 608
-10 to 120 [mV]
0 to 2000 []
Minimum Span
25°C (45°F)
10°C (18°F) 3 mV 20
A/D Accuracy
°C
°F
±3.0 ±0.77
±5.4 ±1.39
±0.4
±0.72
±0.2
±0.36
±0.35 ±0.25
±0.63 ±0.45
±0.5
±0.9
±0.3
±0.54
±0.5
±0.9
±0.4
±0.72
±1.0
±1.8
±0.7
±1.26
±0.5
±0.9
±1.0
±1.8
±0.6
±1.08
±0.35 ±0.2
±0.63 ±0.36
±0.7
±1.26
±1.0
±1.8
±0.9
±1.62
±0.6
±1.08
±0.7
±1.26
±1.0
±1.8
±0.35 ±0.3
±0.63 ±0.54
±0.35
±0.63
±0.14
±0.25
±0.25
±0.45
±0.18
±0.324
±0.18
±0.324
±0.16
±0.29
±1.3
±2.23
±0.14
±0.25
±0.015[mV]
±0.45 []
Note 1: Note 2:
Total Accuracy = (A/D Accuracy / Span + D/A Accuracy) or (± 0.1% of calibrated span), whichever is greater. Accuracy of Fieldbus type: A/D Accuracy. For T/C input, add Cold Junction Compensation Error (± 0.5°C) to the total accuracy. Example: when selecting Pt100 with measurement range of 0 to 400 °C 0.14°C / 400°C×100% of span +0.03% of span = 0.065% of span Since the value is smaller than ±0.1% of span, the total accuracy is ±0.1%. T/C C type is same as W5 (ASTM E988).
D/A Accuracy
±0.03% of span
IM 01C50G01-01EN
<7. General Specifications>
Table 7.4 Temperature coefficient
Sensor Type
Thermocouples E, J, K, N, T, L, U
Thermocouples R, S, W3, C
Thermocouple B
100°C Reading < 300°C 300°C Reading
RTD
mV
ohm
Temperature Coefficient 0.08°C + 0.02% of abs.reading 0.25°C + 0.02% of abs.reading 1°C + 0.02% of abs.reading 0.5°C + 0.02% of abs.reading 0.08°C + 0.02% of abs.reading 0.002 mV + 0.02% of abs.reading 0.1 + 0.02% of reading
Note 1: Note 2:
The "abs.reading" for thermocouples and RTD means the absolute value of the reading in °C. Example of "abs.reading" When the temperature value is 250 Kelvin, "abs.reading" is 23.15. |250-273.15|= 23.15 Ambient Temperature Effect per 10 °C change is ±0.1% or ±(temperature coefficient/span), whichever is greater. Example of Ambient Temperature Effect Conditions:
1) Input Sensor: Pt100 2) Calibration Range: -100 to 100°C 3) Reading value: -50°C Ambient Temperature Effect per 10°C Temperature Coefficient/Span=(0.08°C+0.02/100×|-50°C|)/{100°C-(-100°C)}= 0.00045 0.045% Therefore, Ambient Temperature Effect is ±0.1%/10°C
7-11
IM 01C50G01-01EN
<7. General Specifications>
7.2 Model and Suffix Codes
Model
Codes
YTA610 YTA710
· · · · · · · · · · · · · · · ·
Output Signal
-D*2 · · · · · · · · · · · · · -J · · · · · · · · · · · · · · -F · · · · · · · · · · · · · ·
--
A · · · · · · · · · · · · ·
Sensor input
1 · · · · · · · · · · · · 2 · · · · · · · · · · · ·
Housing code
A · · · · · · · · · · C · · · · · · · · · ·
Electrical Connection 0 · · · · · · · · · 2 · · · · · · · · · 4 · · · · · · · · ·
Integral Indicator
D · · · · · · N · · · · · ·
Mounting Bracket
B · · · · · D · · · · · J · · · · · · K · · · · · N · · · · ·
Option codes
/
Description
Temperature Transmitter
4 to 20 mA DC with digital communication BRAIN protocol 4 to 20 mA DC with digital communication HART protocol Digital communication (FOUNDATION Fieldbus protocol)
Always A (Global)
Single Double
Aluminum Stainless
G 1/2 female 1/2 NPT female M20 female
Digital indicator with Local Operating Switch None SUS304 stainless steel 2-inch horizontal pipe mounting bracket *1 SUS304 stainless steel 2-inch vertical pipe mounting bracket SUS316 stainless steel 2-inch horizontal pipe mounting bracket *1 SUS316 stainless steel 2-inch vertical pipe mounting bracket None
Optional specification
*1: For flat-panel mounting, please prepare bolts and nuts. *2: Applicable only for YTA710.
7-12
IM 01C50G01-01EN
<7. General Specifications>
7-13
7.3 Optional Specifications (YTA610 and YTA710)
Item
Description
Lightning protector *4 Allowable current: Max. 6000A (8×20s), repeating 1000A (8×20s), 100 times
Painting *1*6*13
Color and coating change Amplifier cover only *3
Color: Munsell code N1.5 Black Coating: High anti-corrosion coating
Color: Munsell code 7.5BG4/1.5, Jade green Coating: High anti-corrosion coating
Color: Metallic silver Coating: High anti-corrosion coating
Color and coating change
Color: Munsell code 7.5 R4/14, Red
Amplifier and terminal covers *3 Coating: High anti-corrosion coating
Coating change
High anti-corrosion coating
Output signal Low-side Output signal Low-side: 5%, 3.2 mA DC or less. in Transmitter failure *10 Sensor burnout is also set to `Low': 2.5%, 3.6 mA DC.
NAMUR NE43 Compliant *10
Output signal limits: 3.8 mA to 20.5 mA
Failure alarm down-scale: output status at CPU failure and hardware error is 5%, 3.2 mA or less. Sensor burnout is also set to Low: 2.5%, 3.6 mA DC.
Failure alarm up-scale: output status at CPU failure and hardware error is 110%, 21.6 mA or more. In this case Sensor burnout is High: 110%, 21.6 mA DC
Data Configuration *2 Description into "Descriptor" parameter of HART protocol (max. 16 characters)
Wired tag plate
SUS316 stainless steel tag plate wired onto transmitter
Sensor matching
RTD sensor matching function
Attached flameproof packing adapter*5*7
Electrical connection G1/2 female Applicable cable: O.D.8.0 to 12 mm
2pc.
EAC approval and
EAC approval and Russian pattern approval marking
Russian pattern
approval marking*9*11*13
EAC approval marking EAC approval marking without Russian pattern approval marking
without Russian pattern approval marking*9*11*13
High ambient-temp
Refer to Table 7.5 Temperature coefficient
characteristic type*8*13
Manufacturing*12*14
Optional code to specify the manufacturing factory
Code A P1 P2 P7 PR X2 C1
C2
C3 CA N4 CM1 V52
VR
VE
R1 SG
Note: The indication of the nameplate shows an initial shipment state. *1: Not applicable for Stainless housing. *2: Applicable for only HART type. *3: Except for Amplifier and terminal cover, color and coating are general specification. *4: Lightning protector (surge absorber) can be removed from, or added to the equipment. *5: Combination with other Explosion protected other than TIIS flameproof is not possible. *6: The combination of X2 and P is not possible. *7: Applicable for Electrical Connection code 4. (The thread of connection between YTA and CABLE GLAND is M20, and the thread of
connection between CABLE GLAND and CABLE is G1/2.) *8: Applicable for only YTA710. *9: Not applicable for BRAIN type. *10: Not applicable for Fieldbus type. *11: Combination with other Explosion protected other than EAC Explosion-proof type is not applicable. *12: If SG is not attached, it is made in China. (It includes English name plate and English IM.) *13: Selection of SG is required. *14: In principle when this code is specified, the product made in Singapore will be delivered.
IM 01C50G01-01EN
<7. General Specifications>
7-14
Table 7.5 Temperature coefficient (R1)
Sensor Type
B
E
J
K
N
R T/C
S
T
C
W3
L
U Pt100 Pt200 Pt500 RTD Pt1000 JPt100 Cu10 Ni120 mV ohm
Input Range °C
100 to 300 300 to 1000 1000 to 1820
-200 to 0 0 to 1000 -200 to 0 0 to 1200 -200 to 0 0 to 1372 -200 to 0 0 to 1300 -50 to 0 0 to 200 200 to 1768 -50 to 0 0 to 200 200 to 1768 -200 to 0 0 to 400 0 to 1400 1400 to 2300 0 to 1400 1400 to 2300 -200 to 0 0 to 900 -200 to 0 0 to 600 -200 to 850 -200 to 850 -200 to 850 -200 to 300 -200 to 500 -70 to 150
-70 to 320
-10 to 120 [mV] 0 to 2000 []
A/D Coefficient
±(0.586°C - 0.1433% of reading) ±(0.187°C - 0.0103% of reading) ±(0.038°C + 0.0046% of reading) ±(0.007°C + 0.0158% of abs.reading) ±(0.007°C + 0.0065% of reading) ±(0.009°C + 0.0172% of abs.reading) ±(0.009°C + 0.0065% of reading) ±(0.011°C + 0.0218% of abs.reading) ±(0.011°C + 0.0078% of reading) ±(0.017°C + 0.0265% of abs.reading) ±(0.017°C + 0.0063% of reading) ±(0.088°C + 0.1273% of abs.reading) ±(0.088°C - 0.0142% of reading) ±(0.048°C + 0.0058% of reading) ±(0.088°C + 0.0517% of abs.reading) ±(0.088°C - 0.0106% of reading) ±(0.054°C + 0.0063% of reading) ±(0.011°C + 0.0195% of abs.reading) ±(0.011°C + 0.0044% of reading) ±(0.034°C + 0.0069% of reading) ±( -0.157°C + 0.0205% of reading) ±(0.044°C + 0.0053% of reading) ±( -0.214°C + 0.0237% of reading) ±(0.009°C + 0.0117% of abs.reading) ±(0.009°C + 0.0052% of reading) ±(0.011°C + 0.0148% of abs.reading) ±(0.011°C + 0.0046% of reading) ±(0.015°C + 0.005% of reading) ±(0.023°C + 0.012% of reading) ±(0.015°C + 0.005% of reading) ±(0.015°C + 0.005% of reading) ±(0.015°C + 0.005% of reading) ±(0.320°C + 0.120% of reading)
±(0.010°C + 0.005% of reading)
±(0.441uV + 0.0065% of abs.reading) ±(0.040 + 0.0088% of reading)
D/A Coefficient
±{0.0088% of span + 0.007% of(reading - LRV)}
Note: HART and BRAIN Temperature Effect = A/D coefficient + D/A coefficient Fieldbus Temperature Effect = A/D coefficient (The data in the table is the coeffcient per 10°C change.)
Example 1; Pt100, 0 to 200°C calibration range, 50°C reading (0.015°C + 50°C × 0.005%) + [200°C × 0.0088% + (50 - 0) × 0.007%] = (0.015°C + 0.0025°C) + (0.0176°C + 0.0035°C ) = ± 0.0386°C [ per 10°C change ]
Example 2; T T/C, -100 to 100°C calibration range, -50°C reading (0.011°C + | -50°C | × 0.0195%) + {200°C × 0.0088% + [-50 - (-100)] × 0.007%} = (0.011°C + 0.00975°C) + (0.0176°C + 0.0035°C ) = ± 0.04185°C [ per 10°C change ]
IM 01C50G01-01EN
<7. General Specifications>
7-15
[For Explosion Protected Type]
Item ATEX
Description
[4-20mA & Fieldbus: Flameproof and dust ignition proof approval] Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-1:2014, EN 60079-31:2014 Certificate: KEMA 07ATEX0130 II 2 G Ex db IIC T6/T5 Gb, II 2 D Ex tb IIIC T70°C, T90°C Db Ambient Temperature for Gas Atmospheres: 40 to 75°C for T6, 40 to 80°C for T5 Ambient Temperature for Dust Atmospheres: 30 to 65°C for T70°C, 30 to 80°C for T90°C Enclosure: IP66/IP67 Electrical Connection: 1/2 NPT female and M20 female*1
4-20mA: [Intrinsically safe ia approval]
Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-11:2012 Certificate No. FM16ATEX0019X II 1 G Ex ia IIC T5...T4 Ga Ambient Temperature: 40 to 70°C for T4, 40 to 50°C for T5 Enclosure: IP66/IP67 Electrical parameters:
Supply/Output circuit: Terminals: +, Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min(Without /A) [Intrinsically safe ic] Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-11:2012 Certificate Not Applicable as per Annex VIII to ATEX 2014/34/EU II 3 G Ex ic IIC T5...T4 Gc Ambient Temperature: 30 to 70°C for T4, 30 to 50°C for T5 Enclosure: IP66/IP67 Overvoltage category: I Electrical parameters: Supply/Output circuit: Terminals: +, Ui=32V, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min(Without /A) [Flameproof and Dust Ignition Proof Approval] Same as KF2
Fieldbus: [Intrinsically safe ia approval]
Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-11:2012 Certificate No. FM16ATEX0019X II 1 G Ex ia IIC T4 Ga Ambient Temperature: 55 to 60°C Enclosure: IP66/IP67 Electrical parameters:
Supply/Output circuit: Terminals: +, FISCO field device or Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min(Without /A) [Intrinsically safe ic] Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-11:2012 Certificate: Not Applicable as per Annex VIII to ATEX 2014/34/EU II 3 G Ex ic IIC T4 Gc Ambient Temperature: 30 to 70°C Enclosure: IP66/IP67 Overvoltage category: I Electrical parameters: Supply/Output circuit: Terminals: +, FISCO field device or Ui=32V, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) [Flameproof and Dust Ignition Proof Approval] Same as KF2
Code KF2*5 KU2
KU25
IM 01C50G01-01EN
Item IECEx*8
<7. General Specifications>
Description
[4-20mA & Fieldbus: Flameproof and dust ignition proof approval] Applicable standard: IEC 60079-0:2011, IEC 60079-1:2014, IEC 60079-31:2013 Certificate: IECEx KEM 07.0044 Ex db IIC T6/T5 Gb, Ex tb IIIC T70°C / T90°C Db Ambient Temperature for Gas Atmospheres: 40 to 75°C (40 to 167°F) for T6, 40 to 80°C (40 to 176°F) for T5 Ambient Temperature for Dust Atmospheres: 30 to 65°C (22 to 149°F) for T70°C, 30 to 80°C (22 to 176°F) for T90°C Enclosure: IP66/IP67 Electrical Connection: 1/2 NPT female and M20 female*1
4-20mA: [Intrinsically safe ia, ic pproval]
Applicable Standard: IEC 60079-0:2011, IEC 60079-11:2011 Certificate No. IECEx FMG 16.0014X Ex ia IIC T5...T4 Ga Ex ic IIC T5...T4 Gc Ambient Temperature: 40 to 70°C for T4, 40 to 50°C for T5(Ex ia) Ambient Temperature: 30 to 70°C for T4, 30 to 50°C for T5(Ex ic) Enclosure: IP66/IP67 Overvoltage category: I Electrical parameters(Ex ia)
Supply/Output circuit: Terminal: +, Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Electrical parameters(Ex ic) Supply/Output circuit: Terminal: +, Ui=30V, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) [Flameproof and Dust Ignition Proof Approval] Same as SF2
Fieldbus: [Intrinsically safe ia approval]
Applicable Standard: IEC 60079-0: 2011, IEC 60079-11: 2011 Certificate No. IECEx FMG 16.0014X Ex ia IIC T4 Ga Ex ic IIC T4 Gc Ambient Temperature: 55 to 60°C (Ex ia) Ambient Temperature: 30 to 70°C (Ex ic) Enclosure: IP66/IP67 Overvoltage category: I Electrical parameters (Ex ia)
Supply/Output circuit: Terminals: +, FISCO field device or Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Electrical parameters (Ex ic) Supply/Output circuit: Terminals: +, FISCO field device or Ui=32V, Ci=2.2nF, Li=0mH Sensor circuit:Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) [Flameproof and Dust Ignition Proof Approval] Same as SF2
7-16
Code SF2*5
SU2
SU25
IM 01C50G01-01EN
Item FM (US)
<7. General Specifications>
Description
[4-20mA & Fieldbus: Explosionproof approval] Applicable standard: FM Class 3600: 2011, FM Class 3615: 2006, FM Class 3810: 2005, NEMA250: 2014 Class I, Division 1, Groups A, B, C and D.; Class II/III, Division 1, Groups E, F and G. "FACTORY SEALD, CONDUIT SEAL NOT REQUIRED." Enclosure Ratings: TYPE 4X Temperature Class: T6 Ambient Temperature: 40 to 60°C (40 to 140°F) Electrical Connection: 1/2NPT female*2
4-20mA: [Intrinsically safe approval/non-incendive approval]
Applicable standard: FM Class 3600:2011, FM Class 3610:2015, FM Class 3611:2004, FM Class 3810:2005, ANSI/ISA-60079-0:2013, ANSI/ISA-60079-11:2014, NEMA 250:2003, ANSI/IEC 60529:2004 Intrinsically safe for Class I, II, III Division 1, Groups A, B, C, D, E, F, G, T5...T4 Class I Zone 0 AEx ia IIC T5...T4 Non-incendive for Class I, II, Division 2, Groups A, B, C, D, F, G, T5...T4 Class III, Division 1 T5...T4 Class I Zone 2 Group IIC T5...T4 Ambient Temperature: 40 to 70°C for T4, 40 to 50°C for T5 Enclosure Type 4X, IP66/IP67 Electrical parameters: Intrinsically safe for
Supply/Output circuit: Terminals: +, Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Non-incendive for Supply/Output circuit: Terminals: +, Ui=30V, Ci=22nF, Li=0mH Sensor circuit:Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) [Explosionproof approval] Same as FF1
Fieldbus: [Intrinsically safe approval/non-incendive approval]
Applicable standard: FM Class 3600:2011, FM Class 3610:2015, FM Class 3611:2004, FM Class 3810:2005, ANSI/ISA-60079-0:2013, ANSI/ISA-60079-11:2014, NEMA 250:2003, ANSI/IEC 60529:2004 Intrinsically safe for Class I, II, III Division 1, Groups A, B, C, D, E, F, G T4 Class I Zone 0 AEx ia IIC T4 Non-incendive for Class I, II, Division 2, Groups A, B, C, D, F, G T4 Class III, Division 1 T4 Class I Zone 2 Group IIC T4 Ambient Temperature: 55 to 60°C Enclosure Type 4X, IP66/IP67 Electrical parameters: Intrinsically safe for
Supply/Output circuit: Terminals: +, FISCO field device or Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Non-incendive for Supply/Output circuit: Terminals: +, Ui=32V, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) [Explosionproof approval] Same as FF1
7-17
Code FF1*5
FU1
FU15
IM 01C50G01-01EN
<7. General Specifications>
Item CSA*3*7
FM (Canada)*4*7
Description
[4-20mA & Fieldbus: Explosionproof approval] Applicable standard: C22.2 No. 0-10, C22.2 No. 0.4-04, C22.2 No. 25-M1966, C22.2 No. 30-M1986, C22.2 No. 94-M1991, C22.2 No. 142-M1987, C22.2 No. 157-92, C22.2 No. 213-M1987, C22.2 No.61010-1-12, C22.2 No. 61010-2-030-12 Class I, Groups B, C and D, Class II, Groups E, F and G, Class III. For Class I, Division2 Groups ABCD Locations "FACTORY SEALED, CONDUIT SEAL NOT REQUIRED" Enclosure TYPE 4X Temperature Class: T6 Ambient Temperature: 40 to 60°C Electrical Connection: 1/2 NPT female*2
4-20mA: [Intrinsically safe approval/non-incendive approval]
Applicable standard: CAN/CSA-C22.2 No. 94.2-07, C22.2 No.213:1987, CAN /CSA-C22.2 No. 60079-0:11, CAN/CSA-C22.2 No. 60079-11:14, CAN/CSA-C22.2 No. 60529:05, CAN/CSA-C22.2 No. 61010-1-12, CAN/CSA-C22.2 No. 61010-2-030-12 Intrinsically safe for Class I, II, III, Division 1, Groups A, B, C, D, E, F, G, T5...T4 Ex ia IIC T5...T4 Ga Non-incendive for Class I, II, Division 2, Groups A, B, C, D, F, G T5...T4 Class III Division 1 T5...T4 Ambient Temperature: 40 to 70°C for T4, 40 to 50°C for T5 Enclosure Type: 4X, IP66/IP67 Electrical parameters: Intrinsically safe for
Supply/Output circuit: Terminals: +, Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Non-incendive for Supply/Output circuit: Terminals: +, Ui=30V, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) [Explosionproof approval] Same as CF1
7-18
Code CF1*5
CU1
IM 01C50G01-01EN
<7. General Specifications>
Item CSA*3*7
FM (Canada)*4*7
Description
Fieldbus: [Intrinsically safe approval/non-incendive approval]
Applicable standard: CAN/CSA-C22.2 No. 94.2-07, C22.2 No.213:1987, CAN /CSA-C22.2 No. 60079-0:11, CAN/CSA-C22.2 No. 60079-11:14, CAN/CSA-C22.2 No. 60529:05, CAN/CSA-C22.2 No. 61010-1-12, CAN/CSA-C22.2 No. 61010-2-030-12 Intrinsically safe for Class I, II, III, Division 1, Groups A, B, C, D, E, F, G T4 Ex ia IIC T4 Ga Non-incendive for Class I, II, Division 2, Groups A, B, C, D, F, G T4 Class III Division 1 T4 Ambient Temperature : 55 to 60°C Enclosure Type: 4X, IP66/IP67 Electrical parameters: Intrinsically safe for
Supply/Output circuit: Terminals: +, FISCO field device or Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Non-incendive for Supply/Output circuit: Terminals: +, Ui=32V, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) [Explosionproof approval] Same as CF1
7-19
Code
CU15
IM 01C50G01-01EN
Item NEPSI*8
<7. General Specifications>
7-20
Description
4-20mA and Fieldbus: [Flameproof and Dust Ignition Proof Approval]
Applicable Standard: GB3836.1-2010, GB3836.2-2010, GB12476.1-2013, GB12476.5-2013 Certificate No. GYJ16.1396X Ex d IIC T6/T5 Gb, Ex tD A21 IP66/IP67 T70°C/T90°C Ambient Temperature for Gas Atmospheres: 40 to 75°C for T6, 40 to 80°C for T5 Ambient Temperature for Dust Atmospheres: 30 to 65°C for T70°C, 30 to 80°C for T90°C Enclosure: IP66/IP67 Electrical Connection: 1/2 NPT female and M20 female*1
4-20mA: [Intrinsically safe approval]
Applicable Standard: GB 3836.1-2010, GB 3836.4-2010 GB 3836.20-2010 Certificate No. GYJ16.1423X Ex ia IIC T4/T5 Ga Ambient Temperature: 40 to 70°C for T4, 40 to 50°C for T5 Enclosure: IP66/IP67 in accordance with only IEC 60529 Entity Parameters: Supply/Output circuit: Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit: Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min [+, -, C, 1, 2, 3, 4, 5] to Earth terminal [+, -, C] to [1, 2, 3, 4, 5]
Fieldbus: [Intrinsically safe approval]
Applicable Standard: GB 3836.1-2010, GB 3836.4-2010, GB3836.20-2010 Certificate No. GYJ16.1423X Ex ia IIC T4 Ga Ambient Temperature: 55 to 60°C for T4 Enclosure: IP66/IP67 in accordance with only IEC 60529 FISCO field device Entity Parameters: Supply/Output circuit: Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min [+, -, 1, 2, 3, 4, 5] to Earth terminal [+, -] to [1, 2, 3, 4, 5]
Code NF2 NS2
NS25
IM 01C50G01-01EN
<7. General Specifications>
Item INMETRO*7*8
Description
[4-20mA & Fieldbus: Flameproof and dust ignition proof approval] Applicable Standard: ABNT NBR IEC 60079-0:2013 Versão Corrigida 2: 2016, ABNT NBR IEC60079-1:2016, ABNT NBR IEC 60079-31:2014 Certificate: DEKRA 16.0009 Ex db IIC T6/T5 Gb, Ex tb IIIC T70°C/ 90°C Db Ambient Temperature for Gas: 40 to +75°C for T6, 40 to +80°C for T5 Ambient Temperature for Dust: 30 to +65°C for T70°C, 30 to +80°C for T90°C Enclosure: IP66/IP67 Electrical Connection: 1/2 NPT female and M20 female*1
4-20mA: [Intrinsically safe approval]
Applicable Standard: ABNT NBR IEC 60079-0:2013 Versão Corrigida 2:2016, ABNT NBR IEC 60079-11:2013 Certificate: ABNT 17.0001X Ex ia IIC T5...T4 Ga Ambient Temperature: 40 to 70 °C for T4, 40 to 50 °C for T5 Enclosure: IP66/IP67 Supply/Output circuit:
Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit:
Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A)
Fieldbus: [Intrinsically safe approval "ia" ]
Applicable Standard: ABNT NBR IEC 60079-0:2013 Versão Corrigida 2:2016, ABNT NBR IEC 60079-11:2013 Certificate: ABNT 17.0001X Ex ia IIC T4 Ga Ambient Temperature: 55 to 60 °C Enclosure: IP66/IP67 Supply/Output circuit:
FISCO field device and Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) [Intrinsically safe approval "ic" ] Applicable Standard: ABNT NBR IEC 60079-0:2013 Versão Corrigida 2:2016, ABNT NBR IEC 60079-11:2013 Certificate: ABNT 17.0001X Ex ic IIC T4 Gc Ambient Temperature: 30 to 70 °C Enclosure: IP66/IP67 Overvoltage category: I Supply/Output circuit: FISCO field device and Ui=32V, Ci=2.2nF, Li=0mH Sensor circuit: Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A)
7-21
Code UF1 US1
US15
IM 01C50G01-01EN
Item KOSHA*8
<7. General Specifications>
7-22
Description
[4-20mA & Fieldbus: Flameproof and dust ignition proof approval] Applicable Standard: Notice of Ministry of Labor No. 2016-54, harmorized with IEC 60079-0:2011, IEC 60079-1:2014, IEC 60079-31:2013 Certificate: 17-AV4BO-0457 (Flameproof) 17-AV4BO-0458 (Dust Ignition Proof) Ex d IIC T6/ T5, Ex tD A21 IP66/IP67 T70°C/ T90°C Ambient Temperature for Gas Atmospheres: 40 to 75°C for T6, 40 to 80°C for T5 Ambient Temperature for Dust Atmospheres: 30 to 65°C for T70°C, 30 to 80°C for T90°C Enclosure: IP66/IP67 Electrical Connection: 1/2 NPT female and M20 female*1
4-20mA: [Intrinsically safe approval]
Applicable Standard: Notice of Ministry of Labor No. 2016-54, harmorized with IEC 60079-0: 2011, IEC 60079-11: 2011 Certificate: 17-AV4BO-0459X Ex ia IIC T5...T4 Ambient Temperature: 40 to 70 °C for T4, 40 to 50 °C for T5 Enclosure: IP66/IP67 Supply/Output circuit: Terminals: +, , c
Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5
Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) Electrical Connection: 1/2 NPT female and M20 female *1
Fieldbus: [Intrinsically safe approval]
Applicable Standard: Notice of Ministry of Labor No. 2016-54, harmorized with IEC 60079-0: 2011, IEC 60079-11: 2011 Certificate: 17-AV4BO-0459X Ex ia IIC T4 Ambient Temperature: 55 to 60°C Enclosure: IP66/IP67 Supply/Output circuit: Terminals: +,
FISCO field device and Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) Electrical Connection: 1/2 NPT female and M20 female *1
Code PF2 PS2
PS25
IM 01C50G01-01EN
<7. General Specifications>
7-23
Item EAC*7*8
Description
[4-20mA & Fieldbus: Flameproof and dust ignition proof approval] Applicable Standard: 31610.0-2014 IEC 60079-1-2013 IEC 60079-31-2013 Certificate: TC RU C-JP.98.B.00040 1Ex db IIC T6...T5 Gb, Ex tb IIIC T70°C...T90°C Db Ambient Temperature for Gas Atmospheres: 40 to 75°C for T6, 40 to 80°C for T5 Ambient Temperature for Dust Atmospheres: 30 to 65°C for T70°C, 30 to 80°C for T90°C Enclosure: IP66/IP67 Electrical Connection: 1/2 NPT female and M20 female*1
4-20mA: [Intrinsically safe approval]
Applicable Standard: 31610.0-2014 31610.11-2014
Certificate: TC RU C-JP.98.B.00040 0Ex ia IIC T4...T5 Ga X Ambient Temperature: 40 to 70 °C for T4, 40 to 50 °C for T5 Enclosure: IP66/IP67 Supply/Output circuit: Terminals: +,
Ui=30V, Ii=200mA, Pi=1.0W, Ci=22nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5
Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) Electrical Connection: 1/2 NPT female and M20 female*1
Fieldbus: [Intrinsically safe approval]
Applicable Standard: 31610.0-2014 31610.11-2014
Certificate: TC RU C-JP.98.B.00040 0Ex ia IIC T4 Ga X Ambient Temperature: 55 to 60°C Enclosure: IP66/IP67 Supply/Output circuit: Terminals: +,
FISCO field device and Ui=30V, Ii=300mA, Pi=1.2W, Ci=2.2nF, Li=0mH Sensor circuit: Terminals: 1, 2, 3, 4, 5 Uo=6V, Io=90mA, Po=135mW, Co=10F, Lo=3.9mH Dielectric strength: 500 V a.c.r.m.s.,1 min (Without /A) Electrical Connection: 1/2 NPT female and M20 female*1
*1: Applicable for Electrical Connection Code 2 and 4. *2: Applicable for Electrical Connection Code 2. *3: For Explosionproof approval. *4: For Intrinsically safe approval/non-incendive approval. *5: Not applicable for YTA610. *6: GF1, /GS1 and /GS15 shall be combined with either /VE or /VR. *7: Not applicable for BRAIN type. *8: Selection of SG is required.
Code GF1*6 GS1*6
GS15*6
IM 01C50G01-01EN
<7. General Specifications>
7-24
7.4 Dimensions (YTA610 and YTA710)
2-inch horizontal pipe mounting
Electrical Connection (Output signal)
111(4.37)
Electrical Connection (Input signal)
With Indicator (Optional)
Unit: mm (Approx. inch)
65.4(2.57) 66.1(2.60)
47.1 (1.85)
18.5 (0.73)
Terminal Cover
164(6.46) 102(4.02)
40 (1.57) 25 (0.98)
ø93(3.66)
Shrouding Bolt (For Explosionproof type)
56(2.21)
2-inch pipe ø60.5(ø2.38)
Ground Terminal Tag Plate
Horizontal Pipe Mounting Bracket
(Optional)
2-inch vertical pipe mounting
Electrical Connection (Output signal)
111(4.37)
Electrical Connection (Input signal)
With Indicator (Optional)
Shrouding Bolt (For Explosionproof type)
65.4(2.57) 66.1(2.60)
47.1 (1.85)
18.5 (0.73)
Terminal Cover
ø93(3.66)
191.5(7.54) 209.5(8.25)
Ground Terminal
Tag Plate
Vertical Pipe Mounting Bracket
(Optional)
46 (1.81)
2-inch pipe ø60.5(ø2.38)
Terminals
Communication Terminals Connection hook CHECK METER Connection hook *1
101(3.98)
70(2.76) 98(3.86)
64(2.52)
F0703.ai
M10×1.5 12-deep female for mounting bracket
Terminal Configuration
Power supply and output terminal
External indicator (ammeter) termial *1
Ground terminal *1 : When using an external indicator or a check meter,
the internal resistance must be 10 or less. The hook is not available for Fieldbus communication type.
F0704.ai
IM 01C50G01-01EN
Revision Information
Title
: YTA610 and YTA710 Temperature Transmitters (Hardware)
Manual No. : IM 01C50G01-01EN
Rev-1
Edition Date 1st June 2016 2nd Oct. 2016
3rd Dec. 2017
Page -- -- 1-1 1-5 2-4 2-5
2-6 & 2-7 2-7 2-9 2-10
2-13 to 2-24 3-4 6-1 6-3
6-6 & 6-7 6-7
6-8 & 6-9 7-1 7-2
7-3 7-4 7-5 to 7-9 7-10
7-11 to 7-15
7-16 1-1 2-4 2-5 & 2-8
2-6 & 2-7 2-7
2-15 & 2-16 2-27 3-4 7-2 7-4 7-7
7-9 7-12 7-13 7-16 7-17 7-18
Revised Item New publication. Add YTA610. Incorporate manual change 16-028 and 16-045. Add document No. of GS 01C50H01-01EN. Add YTA610 to the table. Add ATEX Intrinsically safe approval. Revise the name plate. Add name plate (intrinsically safe approval and Flameproof and Dust ignition approval). Add IECEx intrinsically safe approval. Add FM (US) intrinsically safe approval/non-incendive approval. Add FM (Canada) intrinsically safe approval/non-incendive approval. Add "2.7.5 Control Drawing". Add note for Ni120. Revise the description of IMPORTANT. Delete "6.3.2 Replacement of MAIN and TEMP Assembly". Add *1 to the Table 6.4. Add *3 to the Table 6.5. Add *1 to the Table 6.6. Revise 5 year stability. Revise Sensor-Diagnostics. Add software download class. Add SIL certification. Revise supply voltage requirements. Revise accuracy of type N. Delete Ni120. Add YTA610 specifications. Add YTA610. Add *3 to the optional specifications table. Add intrinsically safe and non-incendive type (KU2, KU25, SU2, SU25, FU1,
FU15, CU1, and CU15). Add YTA610. Add document No. of IM 01C50G01-02EN, IM 01C50G01-01P and IM 01C50G01-01K. Add Fieldbus Type. Change applicable standards and Type of Protection and Marking Code,
Add Supply Voltage and Output Signal specifications. Change Name Plate. IECEx intrinsically safe approval Items to be changed. Add Control Drawing. Add Immunity influence during the test. Delete *1 Applicable only for YTA610. Add Immunity influence during the test, Add EU RoHS Directive. Add Ni120. Add Immunity influence during the test, Add EU RoHS Directive and
add SIL Certification. Change Note1. Revise ATEX Intrinsically safe. Revise IECEx. Add NEPSI (NF2, NS2, NS25). Add INMETRO (UF1, US1, US15). Add KOSHA (PF2, PS2, PS25).
IM 01C50G01-01EN
Rev-2
Edition Date 4th Mar. 2018
5th June 2019
Page 2-5
2-8
2-10 2-11 2-14 to 2-29 6-5 7-1 to 7-4 7-13 7-14 7-15
7-16
7-17 7-18 7-23 1-1 3-1 3-2 3-4, 3-5 3-6 5-2 6-5 6-6,6-7 7-1 to 7-13
Revised Item Revise ATEX intrinsically safe approval Add "Ex ic" of ATEX intrinsically safe approval 4-20mA type Add "Ex ic" of IECEx intrinsically safe approval Revise IECEx intrinsically safe approval Revise FM (US) intrinsically safe approval/nonincendive Revise FM (Canada) intrinsically safe approval/nonincendive approval Revise Control Drawing Add Table 6.4 Add BRAIN Type. Add R1 Option and VE, VR Option. Add Table 7.5 Revise ATEX Add Ex ic Revise IECEx Add Ex ic Revise FM (US) Revise CSA, FM (Canada) Add EAC (GF1, GS1, GS15) Add reference for functional safety Add Nut to 3.PART Delete (HART/BRAIN) Add FF Add Character and Selection. Change Parameters Configuration Add Note Delete (HART/FF) Correction of errors Change Standard specification contents
IM 01C50G01-01EN
Adobe PDF Library 15.0