nTAG Interactive 400-00200 Access Point Radio User Manual

Download:
Mirror Download [FCC.gov]
Document ID	699324
Application ID	FbSZcLGTWSkybl+HT76jYw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.84kB (197986 bits)
Date Submitted	2006-08-30 00:00:00
Date Available	2006-08-30 00:00:00
Creation Date	2006-08-16 10:28:16
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2006-08-16 10:28:16
Document Title	Microsoft Word - Operational Manual for the nTAG Access Point Model AP1000.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	EvH

Operational Manual for the nTAG Access Point Model
AP1000
nTAG Interactive
311 Summer Street
Boston, Massachusetts 02210
Page 1
Operational Manual for the nTAG Access Point Model AP1000
Copyright nTAG Interactive
Table of Contents
1.
NOTICES.......................................................................................................3
2.
LIST OF COMPONENTS ..............................................................................3
3.
CONTROLS AND CONNECTORS ...............................................................3
4.
BEFORE YOU BEGIN...................................................................................7
5.
OPERATION .................................................................................................8
6.
DISASSEMBLY.............................................................................................9
7.
CHANNELS SETTINGS ON RADIO MODULE.............................................9
8.
TROUBLESHOOTING ..................................................................................9
List of Figures
Figure 1 Back End Processor (BEP) Front View....................................................................................... 4
Figure 2 Back End Processor (BEP) Rear View ........................................................................................ 4
Figure 3 Radio Module Front View ............................................................................................................ 5
Figure 4 Radio Module Rear View.............................................................................................................. 6
Figure 5 Mounting Pole and Tripod ........................................................................................................... 7
Figure 6 Sample coverage diagram for Access Points............................................................................... 8
Page 2
Operational Manual for the nTAG Access Point Model AP1000
Copyright nTAG Interactive
1. Notices
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This Class [A] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
This device has been designed to operate only with a LinxTechnologys antenna, part
number ANT-2.4-CW-RCT, with a maximum gain of 2.90 dBi. Other antennas having a
gain greater than 2.90 dBi are strictly prohibited for use with this device. The required
antenna impedance is 50 ohms.
There are no end user serviceable parts inside the nTAG Access Point. Please return to
nTAG Interactive for any servicing or repair.
FCC Caution: To assure continued compliance, any changes or modifications not
expressly approved by the party responsible for compliance could void authority to
operate this equipment.
2. List of Components
The nTAG Access Point Model AP1000 consists of the following components:
• One Back End Processor (BEP)
• Two Radio Modules
o Data Channel Radio Module marked blue
o Census Channel Radio Module marked green
• One Mounting pole with tripod
• One Power Cable for BEP
• One Ethernet Cable to connect BEP to Event Server
3. Controls and connectors
The following section shows the key controls and connectors for the components
comprising the Access Point.
Page 3
Operational Manual for the nTAG Access Point Model AP1000
Copyright nTAG Interactive
Power indicator
Hard disk Active Indicator
indicator
Figure 1 Back End Processor (BEP) Front View
Back end Processor (BEP) front view
1. Power indicator
2. Hard Disk active indicator
2. Data Channel
Cable
5.Keyboard/Mouse port
indicator
1. Census
Channel Cable
8.Printer Port
10.Power connector
11.On/off Switch
7.VGA port
6.Ethernet port
9.USB port
3.Census Channel
Power Module
4.Data Channel
Power Module
Figure 2 Back End Processor (BEP) Rear View
Back end Processor (BEP) rear view
1. Census Channel Cable (Green) connected to COM Port 1 and COM Port 2 and
associated power supply module
2. Data Channel Cable (Blue) connected to COM Port 3 and COM Port 4 and
associated power supply module
3. Census Channel power module and power plug
Page 4
Operational Manual for the nTAG Access Point Model AP1000
Copyright nTAG Interactive
4. Data Channel power module and power plug
5. Keyboard/Mouse PS/2 type Port
6. RJ-45 Ethernet Port
7. VGA Monitor Port
8. 25 pin Printer port
9. USB Port
10. Power input connector
11. On/Off switch
2. Mounting
bracket
Antennae
Figure 3 Radio Module Front View
Radio Module Front View
1. Antennae
2. Mounting Bracket and screw
Page 5
Operational Manual for the nTAG Access Point Model AP1000
Copyright nTAG Interactive
5. Power Jumper Connector
1. RJ45 connector
2. LED Enable Switch
3. Channel Selection Switch
4. LED Status Indicators
Figure 4 Radio Module Rear View
Radio Module Rear View
1.
2.
3.
4.
5.
RJ45 Serial Communications and 5 VDC Power Connector
LED Enable Switch
8 position Channel Selection Switch
LED Status Indicators
Power Jumper Connector. Note: These Jumper Connectors should not be used
Page 6
Operational Manual for the nTAG Access Point Model AP1000
Copyright nTAG Interactive
4. Mounting pole Screw
3. Telescopic Mounting pole
2. Leg Mounting Screw
1. Tripod Legs
Figure 5 Mounting Pole and Tripod
Mounting Pole and Tripod
1. Tripod Legs
2. Leg mounting screw
3. Telescopic Mounting Pole
4. Screw to secure Telescopic Mounting pole
4. Before you Begin
1. Place the Access Points at predetermined locations to ensure adequate coverage
over for the venue. See sample coverage diagram below.
2. Ensure that power and network connection is available at the location of each
Access Point.
3. Check areas for overhead clearance where Access Points are to be located to
ensure there are no obstructions preventing Radio Modules to be raised.
Page 7
Operational Manual for the nTAG Access Point Model AP1000
Copyright nTAG Interactive
Figure 6 Sample coverage diagram for Access Points
5. Operation
1. Assemble the mounting tripod by extending the legs to form a firm base. Lock the
legs in place by tightening the mounting screw.
2. Attach the two Radio Modules to the top of the mounting pole. Ensure that the
antenna for the radio modules are pointing downward.
3. Rotate the two Radio Modules so that the distance between the Data Channel
antennae and the Census Channel antennae are at least 20 cms. Secure the two
Radio Modules by tightening the Mounting Bracket screws.
4. Unpack the BEP from the packing container and uncoil the attached cables.
5. Attach the enclosed power cable to the power connector on the BEP. The BEP
must be located at the base of the Antenna to meet FCC requirements.
6. Plug in the end of the blue Data Channel cable into the RJ45 Ethernet port on the
Data Channel Radio Module.
7. Plug in the end of the green Census Channel cable into the RJ45 Ethernet port on
the Census Channel Radio Module.
8. Plug one end of the Ethernet Cable into the RJ45 port on the BEP and connect the
other end to the event network.
9. Insert the Data and Census power plugs into appropriate power outlets.
10. Extend the Telescopic Pole to the fullest extent in the available location and
tighten the Mounting Pole screw to secure the pole.
11. Do not turn on power to the BEP until all Access Points have been positioned and
connected to the network. Once all the Access Points have been positioned, turn
on the BEP by plugging the power cable into an power outlet and switching on
the Power switch.
Page 8
Operational Manual for the nTAG Access Point Model AP1000
Copyright nTAG Interactive
6. Disassembly
1. Ensure that all the attendees have handed in their tags to registration and no
further wireless communication is required.
2. Ensure that the event Server has been shut down.
3. Switch off power to the BEP from the BEP Power switch and unplug the power
cable from power outlet.
4. Unplug the Data and Census power modules from the power outlets.
5. Unplug the Ethernet cable from the RJ45 port on the BEP and the other end from
the event network.
6. Loosen the Mounting Pole screw and retract the Telescopic pole.
7. Unplug the Data Channel and Census Channel cables from the RJ45 ports on the
Data and Census Radio Modules.
8. Dismount the Radio modules from the Mounting pole by unscrewing the
Mounting Bracket screws and place in packing container.
9. Disconnect the power cable from the BEP.
10. Coil the Data and Census Channel cables and place in packing container together
with the BEP.
11. Loosen the Leg mounting screws and collapse the tripod legs.
7. Channels Settings on Radio Module
The channel utilized by the Radio Module can be changed by using a screwdriver to
rotate the setting screw. The Data and Census Radio Modules are set to different
channels. By default the Census Radio Module is set to channel 0 and the Data Radio
Module is set to channel 2. Data and Census Radio Modules used in the same event
should be at least two channels apart. Do not change the settings for the Radio Modules
unless directed by nTAG Interactive.
8. Troubleshooting
If the BEP looses contact with either Radio Module, disconnect the Ethernet cable to the
Radio Module and reinsert firmly.
Page 9
Operational Manual for the nTAG Access Point Model AP1000
Copyright nTAG Interactive

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 9
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2006:08:16 10:28:16
Modify Date                     : 2006:08:16 10:28:16
Title                           : Microsoft Word - Operational Manual for the nTAG Access Point Model AP1000.doc
Creator                         : PScript5.dll Version 5.2
Author                          : EvH

EXIF Metadata provided by EXIF.tools