ruwido austria 761A Remote Control with BT 4.0 Low Energy User Manual CONFIDENTIAL

ruwido austria GmbH Remote Control with BT 4.0 Low Energy CONFIDENTIAL

User Manual

ruwido austria gmbh . Köstendorfer Str. 8 . Austria . t +43 6216 4571-0 . www.ruwido.com Page 1 of 3 This document is intellectual property of ruwido austria gmbh and contains confidential information. Reproduction, modification,. communication to third parties and any other use is strictly prohibited without prior written accordance of ruwido austria. © 2015. please note: this document must not be shared with third parties without prior written consent from ruwido firmware version: 0.1.1 product type: 2761-529 ble remote control guide
Confidential Document 2761-529 RCU guide-2015-11-10.docx Page 2 of 3 copyright 2015 ruwido austria gmbh – this document is the intellectual property of ruwido austria gmbh and contains confidential information. reproduction, modification, communication to third parties and any other use is strictly prohibited without prior written accordance of ruwido. 1 LED behaviour during regular operation stb LED:  red LED when BLE command is transmitted  green LED when IR command is transmitted tv LED:  green LED when IR command is transmitted 2 manual pairing  power on STB  press "On Demand" and "Play/Pause" keys for 3 sec to start pairing process (continues red flashing of LED)  LED will stop flashing red if pairing was successful  to delete pairing from remote control press 4 and 6 keys for 3 seconds  LED will flash 4 times red if pairing deletion was successful 3 factory settings  to set remote control back to factory mode press 7 and 9 keys for 3 seconds  LED will flash 4 times 4 notes  factory default setting: BLE mode  pairing information will remain if batteries are being removed / changed  mode settings will remain if batteries are being removed / changed
Confidential Document 2761-529 RCU guide-2015-11-10.docx Page 3 of 3 copyright 2015 ruwido austria gmbh – this document is the intellectual property of ruwido austria gmbh and contains confidential information. reproduction, modification, communication to third parties and any other use is strictly prohibited without prior written accordance of ruwido. DECLARATION User Information FCC 15.2: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Part 15 Statement. FCC 15.19/RSS Gen Issue 3 Sect. 7.1.3 This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Statement Class B Digital Device FCC 15.105: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: o Reorient or relocate the receiving antenna. o Increase the separation between the equipment and receiver. o Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. o Consult the dealer or an experienced radio/ TV technician for help.

Navigation menu