Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2234446 |
| Application ID | 24lD0va81XEIZkwRfcHYlw== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 55.29kB (691144 bits) |
| Date Submitted | 2014-04-04 00:00:00 |
| Date Available | 2014-04-04 00:00:00 |
| Creation Date | 2014-04-01 19:58:21 |
| Producing Software | Microsoft® Word 2010 |
| Document Lastmod | 2014-04-01 19:58:21 |
| Document Title | BMD-200 |
| Document Creator | Microsoft® Word 2010 |
| Document Author: | Rigado, LLC |
Rigado LLC 2601 25th ST SE Suite 200 Salem, Oregon 97302 866-6-RIGADO (f) 971-208-9869 Blumod BMD-200 Module for Bluetooth 4.0 LE The blumod BMD-200 from Rigado is a powerful, highly flexible Bluetooth Smart module based on the nRF51822 SoC from Nordic Semiconductor. With a ARM® Cortex™ M0 CPU, embedded 2.4GHz transceiver, and on-module chip antenna, the BMD-200 provides a complete RF solution with no additional RF design, allowing faster time to market. The BMD-200 provides full use of the nRF51822’s on-chip peripherals, allowing for a wide range of applications without the need for an external host microcontroller; simplifying designs and reducing BOM costs. With an internal DC-DC converter and a voltage supply range of 2.1V to 3.6V, the BMD-200 can be powered directly from a coin cell or two AAA batteries with ultra-low power consumption. Features Based on the Nordic nRF51822 SoC Complete RF solution with integrated chip antenna Integrated DC-DC converter No external components required ARM® Cortex™-M0 32 bit processor Serial Wire Debug (SWD) S100 series SoftDevice ready 256 kB embedded flash program memory 16 kB RAM 8/9/10 bit ADC - 8 configurable channels 15 General Purpose I/O Pins One 32 bit and two 16 bit timers with counter mode SPI Master/Slave (4 Mbps) Low power comparator Temperature sensor Two-wire Master (I2C compatible) UART (w/ CTS/RTS) CPU independent Programmable Peripheral Interconnect (PPI) Quadrature Decoder (QDEC) AES HW encryption Real Timer Counter (RTC) Applications Appcessories iBeacons™ Low-Power Sensors Connected Appliances Lighting Products Health/Fitness devices Wearables BMD-200 V0.1 PRELIMINARY Page Page 1 of 9 Quick Specifications Bluetooth Version Security LE connections Radio Frequency Modulations Transmit power Receiver sensitivity Typical line-of-sight range Antenna 4.0 (Bluetooth Smart) AES-128 up to 8 2.402GHz to 2480GHz GFSK at 250 kbps, 1 Mbps, 2 Mbps data rates +4 dBm -93 dBm 30 - 150 meters Integrated ceramic chip Current Consumption TX only @ +4 dBm, 0 dBm, -4 dBm RX only @ 2 Mbps, 1 Mbps, 250 kbps CPU @ 16MHz from flash, from RAM System Off , w/ 16K RAM, 8K RAM, no RAM retention 16 mA, 10.5 mA, 8 mA 13.4 mA, 13 mA, 12.6 mA 4.4 mA, 2.4 mA 1.8 uA, 1.2 uA, 0.6 uA Dimensions Length Width Height 17.00 mm 17.00 mm 2.89 mm Hardware Interface Power supply SPI Master/Slave, UART, Two-Wire Master, GPIO 2.1V to 3.6V Certifications FCC FCC part 15 modular qualification BMD-200 V0.1 PRELIMINARY Page 2 of 9 Absolution Maximum Ratings Symbol Parameter Min. Max. Unit VCC_MAX Voltage on supply pin -0.3 3.9 VIO_MAX Voltage on GPIO pins -0.3 VCC + 0.3 Storage Temperature Range -40 125 °C TS Operating Conditions Symbol VCC TR_VCC TA Parameter Min. Typ. 2.1 3.0 3.6 60 ms -25 25 75 °C Operating supply voltage Supply rise time (0V to 1.8V) Operating Ambient Temperature Range Max. Unit GPIO Specifications Symbol Parameter Min. Typ. Max. Unit VIH Input High Voltage 0.7 x VCC VCC VIL Input Low Voltage VSS 0.3 x VCC VOH Output High Voltage VCC – 0.3 VCC VOL Output Low Voltage VSS 0.3 RPU Pull-up Resistance 11 13 16 kΩ RPD Pull-down Resistance 11 13 16 kΩ Note: GPIO have a standard drive strength of 0.5 mA, and a high drive strength of 5 mA. Maximum number of high drive strength pins is 3. Clocks The BMD-200 module requires two clocks, a high frequency clock and a low frequency clock. The high frequency clock is provided internally by a high-accuracy 16-MHz crystal as required by the nRF51822 for radio operation. The low frequency clock can be provided internally by an RC oscillator or synthesized from the fast clock; or externally by a 32.768 kHz crystal. An external crystal provides the lowest power consumption. BMD-200 V0.1 PRELIMINARY Page 3 of 9 32.768 kHz Crystal Specification Requirements Symbol fnom Ftol,BLE Parameter Crystal frequency Frequency tolerance, Bluetooth low energy applications. Typ. Max. Unit 32.768 kHz ±250 ppm Cl Load Capacitance 12.5 pF Co Shunt Capacitance pF Rs Equivalent series resistance 50 80 kΩ Cpin Input Capacitance on XTAL1 & XTAL2 pF 32.768 kHz Oscillator Comparison Symbol Parameter Typ. Max. Unit IX32k Current for 32.768kHz Crystal Oscillator 0.4 uA IRC32k Current for 32.768kHz RC Oscillator 0.8 1.1 uA ISYNT32k Current for 32.768kHz Synthesized Oscillator 15 uA FTOL,X32k Frequency Tolerance, 32.768kHz Crystal Oscillator ±250 ppm F TOL,RC32k Frequency Tolerance, 32.768kHz RC Oscillator ±2 F TOL,SYNT32k Frequency Tolerance, 32.768kHz Synthesized Oscillator ±34 ppm Note: FTOL,X32k is max tolerance allowed for BLE applications. Actual tolerance depends on the crystal used. BMD-200 V0.1 CONFIDENTIAL Page 4 of 9 Pinout Top View Name P0.24 P0.25 P0.26 P0.27 P0.00 P0.01 P0.02 P0.03 P0.04 P0.05 P0.06 P0.08 P0.09 P0.10 P0.11 SWDIO SWDCLK VCC GND Pin description (PRELIMINARY) Pin Direction Description In/Out GPIO In/Out GPIO In/Out GPIO/AIN1/XTAL2 (32.768kHz) In/Out GPIO/AIN0/XTAL1(32.768kHz) 11 In/Out GPIO/AREF0 12 In/Out GPIO/AIN2 13 In/Out GPIO/AIN3 14 In/Out GPIO/AIN4 15 In/Out GPIO/AIN5 16 In/Out GPIO/AIN6 17 In/Out GPIO/AIN7/AREF1 20 In/Out GPIO 21 In/Out GPIO 22 In/Out GPIO 23 In/Out GPIO 24 In/Out SWD IO/ ̅̅̅̅̅̅̅̅̅ 25 18 1, 2, 3, 4, 7, 10, 19, 26, (27, 28 opt.) In Pwr SWD Clock 1 +2.1 to +3.6VDC input 2 Pwr Electrical Ground Note 1: SWDCLK has a 12 kΩ pull-down resistor. Note 2: An external capacitor for VCC is not strictly required, however using a 1µF - 4.7µF ceramic capacitor is recommended. BMD-200 V0.1 CONFIDENTIAL Page 5 of 9 Mechanical Dimensions Recommended PCB Land Pad (Top view) (All dimensions are in mm) BMD-200 V0.1 CONFIDENTIAL Page 6 of 9 Recommended Copper Keepout The area under and extending out from the antenna portion of the module should be kept clear of copper and other metal. The module should be placed at the edge or, ideally, at the corner of the PCB with the antenna edge facing out. BMD-200 V0.1 CONFIDENTIAL Page 7 of 9 FCC Certification The BMD-200 module has a certification from the FCC to be used as a modular transmitter. Devices that include the BMD-200 must state on the label that it “Contains FCC ID: 2AA9B01”. FCC Statement This device has been tested and found to comply with part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Operation is subjected to the following two conditions: (1) This device may no cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Modification to this product will void the user’s authority to operate this equipment. Note: Modification to this product will void the users’ authority to operate this equipment. FCC Important Notes: (1) FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter should be installed and operated with a minimum distance of 20 Centimeter between the radiator and your body and must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with Part 15 of the FCC Rules. Operation is subject the following two conditions： (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. BMD-200 V0.1 CONFIDENTIAL Page 8 of 9 The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. Modular could be only used in mobile or fix device, and could not be used in any portable device. Caution! The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modification could void the user authority to operate the equipment. (2) Co-location Warning: This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. (3) OEM integration instructions： This device is intended only for OEM integrators under the following conditions： The antenna must be installed such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmit or antenna. The module shall be only used with the integral antenna(s) that has been originally tested and certified with this module. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirement with this module installed(for example, digital device emission, PC peripheral requirements, etc.) (4) OEM integration instructions： In the event that these conditions cannot be met (for example certain laptop configuration or colocation with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these and circumstance, the OEM integrator will be responsible for reevaluating. The end product (including the transmitter) and obtaining a separate FCC authorization. (5) End product labeling： This transmitter module is authorization only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following： “Contains Transmitter Module FCC ID: 2AA9B01 (6) Information that must be placed in the end user manual： The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. BMD-200 V0.1 CONFIDENTIAL Page 9 of 9
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 9 Language : en-US Title : BMD-200 Author : Rigado, LLC Creator : Microsoft® Word 2010 Create Date : 2014:04:01 19:58:21-07:00 Modify Date : 2014:04:01 19:58:21-07:00 Producer : Microsoft® Word 2010EXIF Metadata provided by EXIF.tools