Xplore XC6 User Guide Instruction Manual UG EN

User Manual: xplore XC6 - Instruction Manual Free User Guide for Xplore Tablet and eReader, Manual

Open the PDF directly: View PDF .
Page Count: 112

Download
Open PDF In Browser	View PDF

Contents
Welcome

About your computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Contacting Xplore – service and questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Getting Started

Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Back view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Left side view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Right side view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Bottom view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Top view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Quick-start guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Application, Windows, and hot keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Using the Tablet

Turning on the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Turning off the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using the Reset switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Suspending and resuming operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Suspending operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Resuming operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

XC6 User’s Handbook

Contents

Using the pen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Using the digitizer to perform mouse functions. . . . . . . . . . . . . . . . . . . . . . . 39
Changing the pen double-click speed . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Positioning the pen and pen tether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Using the fingerprint scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Changing the screen orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Adjusting the screen brightness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Enabling automatic backlight control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Optimizing screen settings for outdoor use . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Docking the tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Connecting devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Connecting to a local area network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Connecting USB-compatible devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Connecting an external microphone, headphone, or speakers . . . . . . . . . . . . 48
Adjusting microphone volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Adjusting headphone or speaker volume . . . . . . . . . . . . . . . . . . . . . . . . 48
Connecting a monitor or projection panel (optional). . . . . . . . . . . . . . . . . . . 49
Activating the monitor or projection panel. . . . . . . . . . . . . . . . . . . . . . . 49
Connecting a device to the serial port (standard). . . . . . . . . . . . . . . . . . . . . . 50
Connecting an XPL expansion module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Using the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Charging the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
If you do not have an external battery charger . . . . . . . . . . . . . . . . . . . . 51
If you have an external battery charger . . . . . . . . . . . . . . . . . . . . . . . . . 52
Removing and installing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Removing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Installing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Discarding batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Using power options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Displaying power options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

XC6 User’s Handbook

Contents

Checking battery power status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Selecting a power plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Selecting power options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Selecting Power (On/Off) / Backlight (On/Off) / Sleep/ Resume
button options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Tips for conserving battery power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Accessing the Solid State Drive (SSD) cartridge . . . . . . . . . . . . . . . . . . . . . . . . . 60
Re-installing the drive carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Accessing the MicroSD and SIM compartment . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Programming hot keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Programming hot keys to start applications,
open documents, or go to a website . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Programming hot keys to perform predefined functions . . . . . . . . . . . . . . . . 68
Programming hot keys to perform other key functions . . . . . . . . . . . . . . . . . 70

Maintaining the Tablet

Caring for the tablet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Checking power cords and connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Protecting the computer from damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Preventing the computer from overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Storing the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Caring for the display screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Protecting the display screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
When to replace the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Calibrating the digitizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Troubleshooting

XC6 User’s Handbook

Contents

Using BIOS and AOS Functions

Disabling the Auto Power feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Enabling automatic LCD backlight control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Glossary

Hardware Specifications

Agency Notices

Environmental Policy and Recycling Program

103

Environmental policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Risk reduction, prevention, and resource management . . . . . . . . . . . . 103
Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Continuous improvement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Take back and recycling program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Environmental and Sustainability Corporate Report . . . . . . . . . . . . . . . . . . . . . 105
Index

107

XC6 User’s Handbook

Disclaimer
Xplore Technologies® has made every effort to ensure the accuracy and
completeness of this document; however, because ongoing development
efforts are made to continually improve the capabilities of our products,
we cannot guarantee the accuracy of the contents of this document. We
disclaim liability for errors, omissions, or future changes herein.

Trademarks
Xplore and the Xplore logo are registered trademarks of Xplore
Technologies Corp.; iX104, XC6, XC6 Lite, and XC6 Dual Mode are
trademarks of Xplore Technologies Corp. Kensington and MicroSaver are
registered trademarks of the Kensington Technology Group. Microsoft is a
registered trademark of Microsoft Corporation. Windows 8.1, and
Windows 7 are trademarks of Microsoft Corporation. MicroSD is a
registered trademark of the Personal Computer Memory Card International
Association. Intel and Core, are registered trademarks of Intel
Corporation. Wi-Fi is a trademark of the Wireless Ethernet Compatibility
Alliance (WECA). ISODAMP is a registered trademark of Aearo
Company.
All other brands, product names, company names, trademarks and service
marks used herein are property of their respective companies.

Copyright
Copyright © 2003-2014 Xplore Technologies Corp. All rights reserved.
No part of this publication may be copied, reproduced, or translated,
without the prior written consent of Xplore Technologies. No part of this
publication may be stored or transmitted in any electronic form without
the prior consent of Xplore Technologies. Any unauthorized use is a
violation of copyright laws.

Publication information
PN: 95-01110, Rev. A
April 7 2014

XC6 User’s Handbook

Declaration of conformity
DECLARATION OF CONFORMITY according to FCC Part 15, IC ICES-003, and
RTT&E directives
Responsible Party Name: Xplore Technologies
Address: 14000 Summit Drive, Suite 900, Austin, Texas 78728
Telephone: 512.336.7797
Declares that product: Model Series: iX104C6 complies with Part 15 of the FCC Rules.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and, (2)
This device must accept any interference received, including interference that may
cause undesired operation.



WARNING
Changes or modifications to this unit not expressly approved by the party responsible for
compliance may void the user’s authority to operate this equipment.

For more information about FCC rules and their applicability to the XC6, see Appendix
E, “Agency Notices.”

Energy Star Partner

Warranty information
The XC6 is backed by a standard 36-month International Limited Warranty. An
extended International Limited Warranty is available. Check the service kit included
with your computer for warranty terms and conditions.

XC6 User’s Handbook

Important safety information
Before you use the XC6 (referred to as the tablet), read these safety instructions
and the operation instructions in this handbook.
Failure to observe all these instructions voids the Limited Warranty and may lead
to suspension or denial of services to the offender, or legal action, or both.
Follow any special regulations governing the use of the tablet and, if radio-enabled,
always switch it off in areas where radio devices are forbidden or when the radio device
can cause interference or danger.
Always follow any safety laws and regulations pertaining to the use of cell phones and
two-way radios, because these laws and regulations typically apply to the use of the
wireless-enabled tablet.
Observe all restrictions on the use of radio equipment in fuel depots (fuel storage and
distribution areas), chemical plants, and wherever blasting operations are in progress or
in any area in which restrictions on radio transmissions are imposed.
Switch off the tablet when in an aircraft. The tablet is not FAA-approved for use on
aircraft. The effect of the use of the tablet in aircraft is unknown. Using the tablet in an
aircraft may affect aircraft instrumentation, communication, and performance; may
disrupt the network; and may be illegal.
Operating the wireless-enabled tablet may interfere with the functioning of
inadequately protected medical devices such as pacemakers. Consult a physician or the
manufacturer of the medical device if you have any questions.
Radio signals from your tablet will not affect the operation of most modern equipment,
but certain electronic equipment, including automotive systems, may not be shielded
against radio signals from your tablet. Check with the manufacturer of your motor
vehicle or the manufacturer’s representative to determine whether using the tablet will
present any safety issues.
Avoid using the tablet in any environment that requires your full attention, such as
when driving a vehicle. If you need to use your tablet while driving, have a passenger
use it for you or find a safe location to halt your vehicle.



XC6 User’s Handbook

WARNING – BATTERIES
Use only battery types specified in this handbook. Using any other type of battery can be
dangerous and can disable the tablet. Do not drop or mishandle the batteries, immerse
them in water, or subject them to high heat. Doing so could increase the risk of explosion
or leakage, and possibly cause injury. The lithium-ion batteries used in this equipment
contain material that is hazardous to your health. If battery contents come in contact with
the eyes, IMMEDIATELY flush the affected area with clean water for 15 minutes and have
someone else summon medical attention for you. Unaffected persons should assist the
affected individual in the vital first flushing of the eyes. RECHARGING THE BATTERY
MUST ONLY BE CARRIED OUT IN ANON-HAZERDOUS AREA USING THE SUPPLIED
AC ADAPTOR. The definition of hazardous areas can be found in Standard EN 60079-10.



WARNING
When operating the tablet in a known explosive environment do not remove or replace the
battery while the circuit is live. Before removing the battery verify that the area is known to
be free of ignitable concentrations of flammable substances.
EXPLOSION HAZARD – DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS
AREA IS KNOWN TO BE NON-HAZARDOUS.
AVERISSEMENT – RISQUE D’EXPLOSION. NE PAS DÉBRANCHER TANT QUE LE
CIRCUIT EST SOUS TENSION, À MOINS QU’IL NE S’AGISSE D’UN EMPLACEMENT
NON DANGEREUX.



WARNING
EXPLOSION HAZARD – DO NOT REPLACE THE BATTERY UNLESS POWER HAS
BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
AVERTISSEMENT – RISQUE D'EXPLOSION – COUPER LE COURANT OU
S'ASSURER QUEL'EMPLACEMENT EST DESIGNE NON DANGEREUX AVANT DE
REPLACER LE BATTERY.



WARNING
EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR
SUITABILITY FOR CLASS I, DIViSION 2.
AVERTISSEMENT – RISQUE D'EXPLOSION – LA SUBSTITUTIOND E
COMPOSANTSP EUTR ENDRE CE MATERIEL INACCEPTABLE POUR LES
EMPLACEMENTS DE CLASSE I, DIVISION 2.



WARNING
EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS
BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
AVERTISSEMENT – RISQUE D'EXPLOSION – AVANT DE DECONNECTER
L'EQUIPEMENT, COUPER LE COURANT OU S'ASSURER QUE L'EMPLACEMENT
EST DESIGNE NON DANGEREUX.



WARNING
Do not use any dock or any other accessory or attachment that is not manufactured or
supplied by Xplore or an authorized Xplore accessories supplier. Use of any accessory or
attachment that is not supplied or approved for use with the tablet by Xplore is not
permitted because it may cause hazards.

Operate the tablet only from the type of power source indicated on the marking label.
(See page 51 for more information about the battery and power supply.) Route power
supply cords so that they are not likely to be walked on or pinched by items placed
upon or against them. Pay particular attention to cords at plugs and convenience
receptacles, and at the point where cords exit from the tablet or its dock. Do not
overload wall outlets, extension cords, or integral convenience receptacles because this
can cause fire or electric shock.

XC6 User’s Handbook

Unplug the tablet and refer the tablet and dock for service to qualified
service personnel if any of the following conditions occur:
■ The power supply cord or plug is damaged.
■ The tablet or dock does not operate normally when you follow the

instructions in this book.
■ The tablet or dock exhibits a distinct change in performance.

Adjust only controls for which there are instructions in this book. An
improper adjustment of other controls can result in damage and may
require extensive work by a qualified technician to restore the tablet or
dock to normal operation.
CAUTION
Avoid prolonged physical contact with the exposed metal surfaces on
the front and back of the tablet. While the tablet may not feel hot to the
touch, if you maintain physical contact with the tablet for a long time
(for example, if you rest the tablet on your lap for a long time), your skin
may suffer low-heat injury. In addition, be careful when you remove a
PC card that has been used for a long time, because the card may be
hot.

XC6 User’s Handbook

Welcome
Welcome to the Xplore Technologies® XC6™tablet PC, the rugged
tablet designed, tested, and manufactured to meet the environmental
and physical real-world challenges faced by today’s mobile workers.
Based on years of experience in rugged mobile applications, the XC6
is designed to withstand the abuses of everyday wear and tear.
Advanced technology, innovative design, and a rugged case are just a
few highlights of your XC6 system.

Tablet with enhanced performance antennae

Note: This handbook assumes that you have basic experience
using computers and Microsoft® Windows®.

XC6 User’s Handbook

Welcome

About your computer
The XC6 is a high-performance tablet PC that runs on Microsoft
Windows 7 32-bit, Windows 7 64-bit, and Windows 8.1 64-bit
operating systems.
You can use any of the following methods to control the tablet:
■

Special, enhanced pen (included with the tablet)

■

Your finger

■

Any suitable pointing device

Note: In this handbook, all information applies to all models
unless otherwise noted.

All XC6 tablets have been engineered and tested to meet Military
Standards for Environmental Extremes (MIL STD 810G). Your tablet
includes the following features that make it exceptionally rugged and
durable:
■

Durable, long-lasting, rigid magnesium enclosure

■

Interior and exterior multi-layer magnesium structure

■

Bumper system and gasket protection mechanisms

■

Specialized drive technology

■

Removable, dual, Solid State Drive (SSD) cartridge

■

Integrated, protected wireless LAN and WAN antennas for dual
mode operation

■

Locked-in-place memory, cables, and connectors

■

Proprietary thermal management system

XC6 User’s Handbook

Welcome

Package contents
Check to make sure your package includes the following items:
■

Quick Start Guide

■

Battery pack

■

Power cord

■

AC adapter

■

Stylus pen (attached to tablet)

■

Stylus pen tether (attached to tablet)

■

XC6 tablet PC

■

Warranty information kit

■

Operating System Recovery Guide

Optional accessories
Your package also includes any optional accessories you ordered.
Docking options
■

xStand Desktop Docking Station

■

xDock Vehicle Docking Station

Carrying cases
■

Shoulder cases

■

Portfolio case

■

Dockable case

Memory
■

XC6 User’s Handbook

4, 8 or 16 GB DDR III RAM

Welcome

Storage
■

60, 120, or 240 GB Solid State Drive (SSD) single drive
configuration
Note: Drive bay carrier can be configured to use 2 SSDs,

Power options
■

AC adapter with U.S. cord

■

Extended life battery pack (80.75 watt hours)

■

Auto adapter (cigarette lighter adapter)

Additional accessories

■

Top-mounted Fast-Lock GPS II Pro (submeter accuracy)

■

Non-rugged USB optical disk drive

■

USB rugged, backlit keyboard (83-key)

■

Replaceable drive cartridges

■

Active stylus

XC6 User’s Handbook

Welcome

Contacting Xplore – service and questions
Note: To troubleshoot problems (including wireless and GPS
problems), before you call, read the FAQ page of the Xplore
Technologies website. Go to http://www.xploretech.com; then
select Customer Support; then FAQ.

If you purchased your tablet from an authorized Xplore dealer,
contact the dealer for service and support.
If you purchased your tablet directly from Xplore, use any of the
following methods to contact Xplore for service and support:
Website

http://www.xploretech.com

E-mail

customersupport@xploretech.com

Toll free

1-866-296-8541, extension 222

Fax

1-512-336-7791

Before you contact Xplore, have the following information ready so
that the customer support representative can quickly provide a
solution:
Product name: XC6
Product serial number
Purchase date
Conditions under which the problem occurred
Any error messages that were displayed
Type of device connected, if any

XC6 User’s Handbook

Getting Started
This chapter gives you an overview of your tablet and includes a
quick-start guide to tablet keys.

Front view

Reset switch
Built-in
microphone
Status indicator
Speaker

Auto Light sensor
SSD indicator
Digital camera
Speaker
Fingerprint scanner

Reset switch

Enables you to turn off the computer when using the Power (On/Off)/Backlight
(On/Off)/Resume key is not effective. (See page 33.)

Built-in microphone

Enables you to input mono audio with noise cancellation. (See page 48.)

Status indicator

Indicates the computer status (on, off, etc.). (See page 26.)

Speakers

Enable you to listen to stereo audio files. Sealed to provide protection from the
environment.

XC6 User’s Handbook

Chapter 1. Getting Started
Front view

Auto Light sensor

Detects ambient light conditions.

SSD indicator

Indicates hard drive activity. (See page 26.)

Digital camera

1-megapixel, auto-focus camera for taking color or black-and-white images
or videos.

Fingerprint scanner

Enables you to use fingerprint verification features. (See page 42.)

XC6 User’s Handbook

Chapter 1. Getting Started
Back view

Back view
Fan cover

Digital camera

SSD carrier

Antenna
cover

Removable
battery pack

Battery
lock
button

Pen

Pen holder

Fan cover

Plastic cover over the thermal transfer bay that manages heat movement out of the
computer.

Antenna cover

For optional wireless LAN and WAN models, protect and secure the radio antennas
(accessible by authorized service personnel only).

Digital camera

5-megapixel, auto-focus camera for taking color or black-and-white images or videos.

SSD carrier

User-accessible drive carrier for SSD storage (can accommodate 2 SSDs).

Removable battery pack

Powers the computer when AC power is unavailable.

Battery lock button

Secures the battery inside the tablet.

Pen

The main device you use to enter data and control applications (instead of a mouse or
a keyboard). Also called the stylus. See “Using the pen” on page 38.

Pen holder

Provides a place to secure the pen when you are not using it.

XC6 User’s Handbook

Chapter 1. Getting Started
Left side view

Left side view
Power On/Off,
Backlight On/Off,
Sleep/Resume button

Kensington
lock slot

Heat exchange

XPL side port

Power On/Off,
Backlight On/Off,
Sleep/Resume button

Press to power on the computer.
Press and hold for more than 4 seconds to force power off.
Momentarily press to toggle the backlight on or off.

Heat exchange

Helps prevent the computer from overheating by forcing heat away from the
computer. (Do not block the vents.)

XPL side port

Permits connection of special devices made expressly for the XC6.

Kensington™ lock slot

Connector for the optional Kensington MicroSaver™ or equivalent compatible
security cable.
Note: Contact your reseller for information about the Kensington security cable.

XC6 User’s Handbook

Chapter 1. Getting Started
Right side view

Right side view

Power
connector

USB ports

Headphones/speaker
mini-jack connector

LAN connector

9-pin serial connector or
optional connector for
external monitor

The connectors on the right side of the computer are located behind the outer doors.

Power connector

For the AC adapter or optional auto adapter. (See “Optional accessories” on
page 15.)

USB 3.0 ports

For Universal Serial Bus devices (compliant with USB Standard Revision 3.0).
Note: The optional Office and Vehicle Docks include additional USB ports. See
“Optional accessories” on page 15.

Headphone/speaker
mini-jack connector

For smartphone compatible headphones or speakers.

LAN connector

For connecting a standard RJ-45 connector to the tablet’s internal local area
network (LAN) card

9-pin serial connector
or
optional external monitor
connector

Serial connector for connecting terminals or other devices that use the RS-232,
RS-422, or RS-485 data transfer standard, or an optional connector for an external
monitor or projection panel.

XC6 User’s Handbook

Chapter 1. Getting Started
Bottom view

Bottom view
Docking connector for the
optional Xplore Tablet Dock

Guide pin receptacles

Docking connector

Enables you to connect the optional xStand Desktop Docking Station or xDock
Vehicle Docking Stations.

Guide pin receptacles

Help assure a secure connection of the optional xStand or xDock.
Note: See “Optional accessories” on page 15.

XC6 User’s Handbook

Chapter 1. Getting Started
Top view

Top view

XPL expansion port

Bumpers

XPL expansion port

A port that permits connection of special devices made expressly for the XC6.

Bumpers

Fabricated from rugged material. Raised to help protect the computer from damage.

XC6 User’s Handbook

Chapter 1. Getting Started
LED indicators

LED indicators
The LED indicator lights show the status of system functions.
Status LED
See Table 1 for
descriptions of LED states.

Table 1

SSD indicator
Solid or flashing green
indicates drive activity.

Status LED indicator states

LED state

AC adapter

Battery

Tablet mode

geen,
blinking
slowly

plugged in

charging

On, Off, or Hibernating

green/cyan,
blinking
slowly

plugged in

green,
breathing

not
plugged in

discharging

plugged in

removed

plugged in

fully charged

not
plugged in

removed

green,
continuous

Action required (if any)

fully charged
charging
Sleep mode

discharging

XC6 User’s Handbook

Chapter 1. Getting Started
LED indicators

Table 1

Status LED indicator states (continued)

LED state

AC adapter

Battery

Tablet mode

off (no light)

all
conditions

all conditions

Off or Hibernating (or
any Night Vision mode)

blue,
continuous

all
conditions

all conditions

On. Front or rear
camera is active.

red, blinking
quickly

not
plugged in

discharging
< 10%

Plug the tablet into an AC/DC power
source or install a charged battery.

red,
continuous

not
plugged in

discharging
< 3%

Plug the tablet into an AC/DC power
source or install a charged battery.

installed

Off

Battery is critically low.Plug the tablet
into an AC/DC power source or install
a charged battery.
or
The tablet has encountered a fault and
is not operating normally. Contact your
computer support personnel, such as
your help desk.

amber,
continuous

all
conditions

installed

High temperature
threshold has been
exceeded.

amber/green,
blinking
quickly

all
conditions

installed

Critical temperature
threshold has been
exceeded.

XC6 User’s Handbook

Action required (if any)

Chapter 1. Getting Started
Quick-start guide

Quick-start guide
This section is a quick guide to using the main features of your tablet.
(See Chapter 2 for detailed information.)

Application, Windows, and hot keys

Hot key 1

Secure Attention
Sequence key
Windows Start key

Function
key

Hot key 2

Hot key 3

Fingerprint scanner

XC6 User’s Handbook

Chapter 1. Getting Started
Quick-start guide

Note: Xplore pre-programs the P2, P2, and P3 hot keys and
Function mode hot key combinations to perform the functions
shown in Table 2, Table 3, and Table 4. However, you can
program them to perform different functions (see “Programming
hot keys” on page 63).

Table 2

Main keys

Press this key...

To perform this function
Log on after resuming operation from power
management, powering on, or locking.
After logging on, launch Windows Task Manager.
Display the Windows Start menu.
Use in combination with another key to perform
various functions.
Fingerprint scanner.

XC6 User’s Handbook

Chapter 1. Getting Started
Quick-start guide

Table 3

Key functions – Windows 7

Press these keys...

To perform this function
Take picture.
Change video ouput.
Rotate screen.
Take video.
Toggle GPS.
Put computer in Sleep mode.

Table 4

Key functions – Windows 8.1

Press these keys...

To perform this function
Open Charm bar.
Transition between open apps.
Change video output.

To define a function, see
“Programming hot keys” on
page 63.

[No pre-programmed function.]
[No pre-programmed function.]
Put computer in Sleep mode.

XC6 User’s Handbook

Using the Tablet
This chapter contains detailed instructions for using the tablet.

Turning on the computer
1.

Make sure the computer is off.
When the computer is off,
the Status LED is off.

Make sure the battery is charged or that the computer is plugged
in to an external power source.

Press the Power On/Off, Backlight On/Off, Sleep/Resume button.

Power On/Off,
Backlight On/Off,
Sleep/Resume
button

XC6 User’s Handbook

Chapter 2. Using the Tablet
Turning off the computer

Turning off the computer
When the computer is in
Sleep mode, the Status LED
is breathing green.

If the computer is in Sleep mode, press the Power On/Off,
button to resume operation. (See
page 35 for information about Sleep mode.)

Backlight On/Off, Sleep/Resume

Power On/Off,
Backlight On/Off and
Sleep/Resume
button

Make sure the battery is charged or that the computer is plugged
in to an external power source.

Save your work and close all programs.

From the Windows Start menu, click Turn Off Computer.

The Turn off computer dialog box opens.

Click Turn Off or press the Power button continuously for more
than 4 seconds.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Turning off the computer

Using the Reset switch
Use the Reset switch only if
you cannot turn off the
computer by any other
means, because you may
lose unsaved data.

If the computer does not seem to be accepting input and you cannot
turn it off by using the method described in “Turning off the
computer,” press the Reset switch. (Use the stylus or a similar
instrument to press the switch).
Reset switch

Note: If the computer does not reset after you press the Reset
switch, try pressing it again.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Suspending and resuming operation

Suspending and resuming operation
For more information, see
“Checking battery power
status” on page 55.

To conserve battery power when you do not want to turn off the
computer or when you need to install a charged battery pack, put the
computer into Sleep mode. (You can suspend operation without
closing any programs or Windows.)
When you suspend operation:
■

Programs that are running stop (but do not close).

■

Active data is saved.

■

The system enters one of the following low-power modes:
• Sleep (Suspend-to-RAM) mode – The Status LED light is
breathing green. Active data is saved in RAM and most other
components are turned off.
Although the computer uses very little power when in Sleep
mode, eventually the battery’s power does run out. If you do
not plan to use the computer for an extended period of time,
turn the computer off or put it in Hibernation mode instead of
Sleep mode.
• Hibernation mode – Active data is saved on the SSD and
power usage is reduced to the same level as when the
computer is turned off. In Hibernation mode, there is no
danger of losing data if battery power is lost.

Notes:
If you have set your computer to turn power off (in the Power Options
utility in Windows Control Panel), you cannot suspend operation. To
change power settings, see “Selecting Power (On/Off) / Backlight (On/
Off) / Sleep/ Resume button options” on page 58.
In the default configuration, the P3 key puts the computer in Sleep
mode and the Power button shuts down the computer. To change
these settings, see “Programming hot keys to perform predefined
functions” on page 68.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Suspending and resuming operation

If your computer is connected to a network, the network may
automatically log you off after a period of inactivity while system
operation is suspended. Contact your help desk or system
administrator to learn your log-off time limit.

Suspending operation
In order to suspend
operation, the Sleep
option must be enabled in
Windows Power Options.
See “Selecting Power
(On/Off) / Backlight (On/
Off) / Sleep/ Resume
button options” on
page 58.

Use one of the following methods to suspend operation:
Method 1

Press the P3 key.

P3 key

Method 2

XC6 User’s Handbook

Press the Windows Start button; then press the right arrow next to
the Shutdown button.

Press Sleep.

Chapter 2. Using the Tablet
Suspending and resuming operation

When operation is suspended, the Status LED displays a breathing
green light.
Windows Start button

Status LED

XC6 User’s Handbook

Chapter 2. Using the Tablet
Suspending and resuming operation

Resuming operation
To resume operation when the computer is in Sleep mode, press the
Power On/Off, Backlight On/Off, Suspend/Resume button.
Note: Press the button only once.

Power On/Off,
Backlight On/Off,
Sleep/Resume
button

Approximately 20 seconds later, the computer resumes normal
operation. When the Status LED displays a continuous green light,
you can begin using the computer.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using the pen

Using the pen
You can use any of the following methods to select items and to
navigate through programs.
■

■

Auto-Sense mode: Use either the multifunction pen or your
finger interchangeably. The computer distinguishes between the
two input modes and automatically adjusts accordingly. This is
the tablet’s default state.
Digitizer mode: Use only the special multifunction pen provided
with the computer.

For more information, see “Programming hot keys to perform
predefined functions” on page 68.
WARNING
Do not use items such as a ball point pen or a screwdriver that can
damage the tablet. Damage caused by using an item not provided with
the tablet is not covered by the tablet warranty.

Note: During the first use of the tablet, or if the action you are
trying to perform does not occur when you use the pen or your
finger to touch the screen, calibrate the digitizer as described in
“Calibrating the digitizer” on page 77.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using the pen

Using the digitizer to perform mouse functions
To perform this function...

Do this

Select an object
(left button click).

Tap the pen tip once on the object.

Perform a double-click.

Quickly tap the pen tip twice on the object.

Perform a right-click.

Hold the pen or your finger directly on the
object for 1 second.

Move or drag an object.

Place the pen tip or your finger on the
object; then continue to hold the pen tip or
your finger against the screen as you move
the pen or your finger.

Changing the pen double-click speed
The pen double-click speed is in sync with the mouse double-click
speed. To change the speed, follow the instructions below.
1.

Click the Windows Start button.

Click the Control Panel option.

In the Control Panel window, select Hardware and Sound >
Set up your Pen and Tablet.

XC6 User’s Handbook

Drag the slider to a faster or slower speed.

Chapter 2. Using the Tablet
Using the pen

Positioning the pen and pen tether
The pen tether helps prevent the loss of your pen. The following
illustrations show how to position the pen and pen tether.
Tether anchored at the bottom

pen tether

pen

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using the pen

Tether anchored on the side

pen tether

pen

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using the fingerprint scanner

Using the fingerprint scanner
The fingerprint scanner enables you to use fingerprint verification to
protect the security of your data.
Fingerprint scanner

The first step for using fingerprint verification is to enroll your
fingerprint to create an association between your username, password,
and fingerprint.
After fingerprint enrollment you will be able to:
■
■

■
■

Use your fingerprint as part of computer login security.
Register Web pages and Windows applications to use your
fingerprint instead of passwords.
Launch applications by swiping your finger the sensor.
Store confidential information in an encrypted form in a
protected folder.

To launch the Fingerprint application:
Tap the icon located on the Windows Desktop.
or
Follow the instructions that appear the first time you turn on the
computer.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Changing the screen orientation

Changing the screen orientation
To rotate the screen orientation from portrait (vertical) to landscape
(horizontal) mode or from landscape to portrait mode:
If your tablet is using Windows 7

Press the Windows Start button.
If your tablet is using Windows 8.1

Rotate the tablet.

portrait mode

XC6 User’s Handbook

landscape mode

Chapter 2. Using the Tablet
Adjusting the screen brightness

Adjusting the screen brightness
Use either of the following methods to adjust the screen brightness:
Method 1
1.

Click Start.

Open the Control Panel.

In the Hardware and Sound area, select Adjust commonly used
mobility settings. Use the Brightness slider to adjust the
brightness.
Display brightness slider

Method 2

In the Windows taskbar, click the power management icon; then
select Adjust screen brightness.

Move the slider bar (located at the bottom of the window) to
change the screen brightness.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Adjusting the screen brightness

Enabling automatic backlight control
When the Auto Light sensor is enabled, the computer automatically
controls the amount of backlight sent to the screen to provide
optimum brightness for the lighting conditions in which you are
working.
Auto Light sensor

To enable automatic backlight control, see page 82.

Optimizing screen settings for outdoor use
1.

Click Start > Control Panel > Appearance and Personalization >
Personalization > Change desktop background.

XC6 User’s Handbook

In the My Themes area, select High Contrast White.

Click the Back button.

Click Display.

Click Medium - 125% to enlarge the icon size; then click Apply.

Click Adjust Resolution. Make sure the screen resolution setting is
1024 by 768 pixels; then click OK.

Chapter 2. Using the Tablet
Docking the tablet

Docking the tablet
If you have the optional xStand office dock or xDock vehicle dock,
connect it to the tablet at the docking port. (See the iX104 Docking
Stations Handbook.)
Docking port

Guide pin receptacles

XC6 User’s Handbook

Chapter 2. Using the Tablet
Connecting devices

Connecting devices
Refer to the following subsections for information about connecting
external devices to your computer.
Note: If the device you want to use does not appear to be
working with your computer, the device may need to be enabled
in the computer’s configuration program. Contact your local help
desk or Xplore reseller.

Connecting to a local area network
Connect a local area network (LAN) cable’s RJ-45 connector to the
internal LAN interface card. (See your network system administrator
for more information.)

LAN connector

Connecting USB-compatible devices
Connect any USB-compatible devices to the computer’s USB ports.

USB ports

XC6 User’s Handbook

Chapter 2. Using the Tablet
Connecting devices

Connecting an external microphone, headphone, or
speakers
Microphone/headphones
mini-jack connector

Note: The connector is
compatible with
smartphones.

Adjusting microphone volume
If necessary, adjust the volume of the microphone as follows:
1.

Press the Windows Start key; then open the Control Panel.

Select Hardware and Sound; then select Sound.

Select the Recording tab.

Select Microphone; then select Properties.

Select the Levels tab.

Adjust the microphone volume or boost.

Click OK.

Adjusting headphone or speaker volume
1.

Click the audio icon
taskbar.

in the Status area of the Windows

The volume control area opens.

If the Mute button indicates that sound is muted, click the button
to turn on the sound.

Move the slider bar up or down to increase or decrease the
volume.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Connecting devices

Connecting a monitor or projection panel (optional)
Monitor/projection
panel connector

Activating the monitor or projection panel
If your tablet includes the optional monitor/projection panel
connector, you can change the video output as follows:
To change the video output to the monitor or projection
panel:

Press the Fn-P1 key combination.
To change the video output back to the computer:

Press the Fn-P1 key combination again.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Connecting devices

Connecting a device to the serial port (standard)
If your tablet includes the standard serial port, you can connect a
terminal or other device that uses the RS-232, RS-422, or RS-485
data transfer standard.
9-pin serial port

Connecting an XPL expansion module
XPL expansion port

Tablet with optional GPS II

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using the battery

Using the battery
You can recharge, remove, and replace the battery pack.

Charging the battery pack
If you do not have an external battery charger
Follow these steps to charge the battery while it is installed in the
computer:
1.

Connect a power source, such as an AC adapter or cigarette
lighter adapter, to the power connector on the computer.

Power connector

If the battery charge is below 95%, the battery begins charging
and the Status LED flashes green. (If the battery charge is higher
than 95%, the battery will not charge, preventing battery
overcharge.)
2.

Check the level of charge. (See “Checking battery power status”
on page 55.)

The charging process continues until the battery charge
reaches 100%.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using the battery

Table 5 shows the approximate time required to charge the battery
level to 100%.
Table 5

Approximate battery charge time

Battery pack capacity

Charge time

Battery pack P/N

55 watt hours (7600 mAh)

1.5 hours

11-01018

68.5 watt hours (9250 mAh)

2.5 hours

11-01019

80.75 watt hours (10625 mAh)

2.5 hours

11-01022

If you have an external battery charger
1.

Remove the battery pack (see page 52).

Use the external battery charger to charge the battery.

Install the battery (see page 54).

Removing and installing the battery
You can remove the battery and use an (optional) external charger to
charge it.
Removing the battery
1.

To swap with a charged battery:

Use one of the methods described in “Suspending operation”
on page 35 to suspend operation.
If a charged battery is not available:

Save your work and close all running programs; then shut
down the computer or put the computer in Hibernation mode
(see “Suspending operation” on page 35).

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using the battery

Note:

To avoid losing unsaved data, wait until the computer
has completed switching to Hibernation mode before
removing the battery.

Use the stylus or a pen to depress the battery lock button.
The battery release latch returns to its original position.

Removable
battery
Battery release
latch
Battery lock
button

Pull the battery away from the computer and remove it.

Note: After removing the battery, you must replace the battery
or connect the computer to an external power supply within
3 to 5 minutes or the computer completely loses power.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using the battery

Installing the battery
1.

Orient the battery with the slides in the empty battery tray.

Slide the battery into the tray and press it firmly until it is seated.

Slide the battery release latch to its original position.
The lock button pops back into the locked position, securing the
battery in place.

Discarding batteries
Dispose of batteries in accordance with your local government
regulations. Under federal, state, or local law, it may be illegal to put
batteries in the trash. Contact your system administrator, municipal
waste disposal department/provider for information.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using power options

Using power options

Displaying power options
On the Windows taskbar, click the battery icon; then select More
The Power Options window opens.

power options.

Checking battery power status
On the Windows taskbar, click the battery icon.
The following window opens, displaying the percentage of power
remaining in the battery:

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using power options

Selecting a power plan
1.

On the Windows taskbar, click the battery icon.
The following window opens:

Select one of the following power plans: (select More power
options in necessary)
Balanced

life.

– Balance between computer performance and battery

Power Saver

– Longer battery life and lower performance.

High performance

– Higher performance and shorter battery life.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using power options

Selecting power options
1.

On the Windows taskbar, right-click the battery icon.

Select Power Options.
The following window opens.

XC6 User’s Handbook

Under the selected power plan, press Change plan settings.

Select the power options you want to use.

Chapter 2. Using the Tablet
Using power options

Selecting Power (On/Off) / Backlight (On/Off) / Sleep/
Resume button options

Power (On/Off)/
Backlight (On/Off)/
Sleep/Resume button

To change what happens when you press the button:
1.

On the Windows taskbar, right-click the battery icon.

Select Power Options.
The following window opens.

Press Choose what the power buttons do.

Select the options you want to use.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Using power options

Tips for conserving battery power
The following tips help you extend the life of your battery by
conserving battery power:
■

■

XC6 User’s Handbook

Use an external power source such as the AC or auto adapter
whenever available.
Suspend operation if you know that you will not be using the
system for a while. (See page 35.)
If you do not plan to use the computer for an extended period of
time, turn it off.
Adjust power options to automatically conserve power. (See
page 57.)
Adjust the display brightness to no brighter than necessary for
comfortable viewing. The display can consume a large portion of
the computer’s power. (See page 44.)
Set the LCD Brightness range to “Power Saving” in the BIOS
Setup Utility. (See page 81.)

Chapter 2. Using the Tablet
Accessing the Solid State Drive (SSD) cartridge

Accessing the Solid State Drive (SSD) cartridge
When you install a new storage drive, follow the instructions in this
section to access the hard drive carrier.
WARNING

Turn off the computer.

Remove all power from the unit, including batteries and other
power sources such as power supplies, cigarette lighter adapters,
and mobile power sources.

Pinch the two center pins with one hand while pushing down on
the lever with the other. The drive carrier will pop up (like the
battery) and permit removal.
Note:

Failure to follow this procedure can result in
damage to the case and the cover, which is not
covered under the Xplore Technologies warranty.
Xplore recommends that you use an
approved Xplore Technologies service center
for this procedure.

Your drive carrier may have two screws installed. If so,
remove them before you exchange the drive carrier.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Accessing the Solid State Drive (SSD) cartridge

Re-installing the drive carrier
1.

Insert the drive with smooth edge into the bay at a slight angle.

Press down until the carrier clicks into place, while pinching the
two center pins.

If your unit had the screws in place, re-attach them.
Note:

XC6 User’s Handbook

Do not use power tools.

Chapter 2. Using the Tablet
Accessing the MicroSD and SIM compartment

Accessing the MicroSD and SIM compartment
Note: This compartment can
handle most MicroSD and
SIM cards.

When you install a MicroSD or SIM card, follow the instructions in
this section to access the compartment.
WARNING

Opening the compartment

Failure to follow this procedure can result in damage
to the case and the cover, which is not covered under
the Xplore Technologies warranty. Xplore
recommends that you use an approved Xplore
Technologies service center for this procedure.

Turn off the computer.

Remove all power from the unit, including batteries and other
power sources such as power supplies, cigarette lighter adapters,
and mobile power sources.

Remove the battery. (See “Removing and installing the battery”
on page 52.)

Lift up on the D-ring and turn it clockwise ¼ of a rotation. Once
the lock is disengaged lift the door to open the compartment.

Installing a MicroSD card

Installing a SIM card

XC6 User’s Handbook

Chapter 2. Using the Tablet
Programming hot keys

Programming hot keys
Xplore pre-programs the P1, P2, and P3 hot keys and Function mode
hot key combinations to perform certain functions by default (see
“Application, Windows, and hot keys” on page 28). However, you
can program them to perform different functions, as described in this
section

Programming hot keys to start applications,
open documents, or go to a website
1.

In the Status area of the Windows taskbar, click the
XC6 Configuration icon.
The Launch Button QuickShow dialog box opens.

XC6 User’s Handbook

Click the Configure button.

Chapter 2. Using the Tablet
Programming hot keys

The Panel Control Center window opens.

Click the Change button next to the key or key combination you
want to program.
The following options appear:

XC6 User’s Handbook

Chapter 2. Using the Tablet
Programming hot keys

Click Launch an Application, Document or Web site.
The following options appear:

XC6 User’s Handbook

Chapter 2. Using the Tablet
Programming hot keys

To start an application:
a.

Click Launch an Application.

Press Browse to find the application you want the hot key or
Function mode hot key combination to start (for example:
word.exe, notepad.exe, excel.exe).

Click Change.

To open a document:
a.

In the Click Open a Document.

Press Browse to find the document you want the hot key or
Function mode hot key combination to open. (For example:
spreadsheet.xls, airports.doc, wiringdiagram.jpg)

Click Change.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Programming hot keys

XC6 User’s Handbook

To open a multimedia file:
a.

Click Open a Multimedia file.

Press Browse to find the name of the multimedia file you
want the hot key or Function mode hot key combination to
open. (For example: 911training.dir, demo.ppt)

Click Change.

To open a Web page:
a.

Click Open a Web page.

Press Browse to find the URL of the Web page you want the
hot key or Function mode hot key combination to open. (For
example: http://www.xploretech.com)

Click Change.

Program more hot keys, or click Close to close the Panel Control
Center window.

Chapter 2. Using the Tablet
Programming hot keys

Programming hot keys to perform predefined
functions
1.

In the Status area of the Windows taskbar, click the
XC6 Configuration icon.
The Launch Button QuickShow dialog box opens.

Click the Configure button.
The Panel Control Center window opens.

Next to the key or key combination you want to program, click
the Change button.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Programming hot keys

The following options appear:

XC6 User’s Handbook

Click Start a predefined function.

In the Function selection drop-down list, select an option.

Program more hot keys, or click Close to close the Panel Control
Center window.

Chapter 2. Using the Tablet
Programming hot keys

Programming hot keys to perform other key
functions
1.

In the Status area of the Windows taskbar, click the
XC6 Configuration icon.
The Launch Button QuickShow dialog box opens.

Click the Configure button.
The Panel Control Center window opens.

Next to the key or key combination you want to program, click
the Change button.

XC6 User’s Handbook

Chapter 2. Using the Tablet
Programming hot keys

The following options appear:

Click Press a key or key combination.
The following options appear:

XC6 User’s Handbook

Chapter 2. Using the Tablet
Programming hot keys

If you want the hot key or hot key combination to perform the
function of a single key:
a.

If the Ctrl, Alt, or Shift boxes are checked, uncheck them.

Click the key you want the hot key or hot key combination to
perform. (For example: F6, G, or Caps Lock)

If you want the hot key or hot key combination to perform the
function of a key combination:
a.

Check the Ctrl, Alt, or Shift box.

From the drop-down list, select the additional key, or click
the key on the keyboard.
Examples

To cause the hot key to perform the print screen function
(Alt-Print Scrn): Check the Alt check box; then select PrtScr
from the drop-down list.
To cause the hot key to perform the paste function (Ctrl-V):
Check the Ctrl check box; then click the V key.
6.

Program more hot keys, or click Close to close the Panel Control
Center window.

XC6 User’s Handbook

Maintaining the Tablet
This chapter provides instructions for maintaining your tablet.

Caring for the tablet
This section provides information about how to keep your tablet in
top working condition.

Checking power cords and connectors
Check AC and DC power cords and power connectors periodically for
damage. Replace the power cord immediately if you find any damage.

Protecting the computer from damage
■

■

Do not place heavy objects on the computer.

■

Do not disassemble the computer.

■

XC6 User’s Handbook

Your computer is designed to sustain a multiple-axis drop to a
non-yielding surface. Do not intentionally drop the computer,
because the cumulative effects of multiple drops may damage the
computer.

Keep the computer at least 5 inches (13 centimeters) away from
any electrical appliance that generates a strong magnetic field,
such as a motor, magnet, TV, refrigerator, or large audio speakers.

Chapter 3. Maintaining the Tablet
Caring for the tablet

Preventing the computer from overheating
The computer monitors its internal temperature. As the internal
temperature approaches the tolerable limits of heat-sensitive
components, system functions are automatically limited or turned off
to prevent damage.
To prevent the computer from overheating, do not obstruct the
computer’s air vents.

air vent area

air vents

XC6 User’s Handbook

Chapter 3. Maintaining the Tablet
Caring for the tablet

Storing the computer
You can store the computer in the Off state for about 30 days with a
fully charged battery installed. After this period, recharge the battery
or replace it with a charged battery.
If you intend to store the computer for more than 30 days, remove the
battery pack and keep it in a cool place.

Caring for the display screen
To clean the display screen, dampen a soft cotton cloth with water
and gently wipe the screen surface.
Note: Do not use isopropyl alcohol to clean the screen. Alcohol
may damage the surface of the screen.

Protecting the display screen
The screen protector is a durable, replaceable writing surface that
protects the display screen from abrasion.
To obtain additional screen protectors, check with your reseller, or go
to the Xplore Web site at www.xploretech.com for ordering
information. Additional information about installation is included
with the screen protectors.

XC6 User’s Handbook

Chapter 3. Maintaining the Tablet
When to replace the pen

Removing the screen protector

Slide your fingernail under the edge of the screen protector and pull
the protector away from the screen.

edge
Installing a new screen protector

Follow the instructions included with your screen protector
replacement kit.
Note: If a screen protector is already installed on the display
screen, remove it before installing the new screen protector.

When to replace the pen
With use, the pen tip may become worn and can scratch the screen.
If your pen exhibits one of the following problems, replace the pen:

■

The pen does not move freely across the screen.

■

The pen does not perform as expected.

XC6 User’s Handbook

Chapter 3. Maintaining the Tablet
Calibrating the digitizer

Calibrating the digitizer
Calibrating the digitizer adjusts the cursor position on the screen
relative to the position of the pen tip or finger. Calibrate the digitizer
to adjust the distance error between where the pen or finger is actually
touching the screen and where the computer is registering the pen or
finger touch.
You may need to calibrate the digitizer in the following situations:
■
■

You are using the computer for the first time.
The previous user of the computer writes with the opposite hand or
at a different pen angle.

■

The computer has not been used for some time.

■

The computer has been serviced.

From the Start menu, select Control Panel.
The Control Panel opens.

XC6 User’s Handbook

Chapter 3. Maintaining the Tablet
Calibrating the digitizer

Select Hardware and Sound.

Hardware and Sound

In the Tablet PC Settings area, select Calibrate the screen for pen
then follow the instructions that appear on the
screen..

or touch input;

Calibrate the
screen for pen
or touch input

XC6 User’s Handbook

Troubleshooting
Table 6 contains solutions to some problems. If you cannot solve the
problem by taking the actions described, contact your local help desk
or your reseller for further assistance.

Table 6

Troubleshooting

Problem

Possible cause and solution

Computer will not start.

• The battery may be defective or discharged to a critically low level.
Connect an external power supply (such as the AC adapter) or
install a charged battery. See “Using the battery” on page 51.
• Internal components may be above or below the acceptable
operating range (below -20° C or above 60° C). After the
temperature returns to safe operating range the computer will start.

The computer will not resume operation
after being suspended.

• The battery may be defective or discharged to a critically low level.
When the battery reaches a critically low level, the computer is
forced into Sleep mode to avoid a total system power failure.
Connect an external power supply (such as the AC adapter) or
install a charged battery. See “Using the battery” on page 51.
• The computer may be at the critical thermal limit. To avoid damage
to heat-sensitive components, the computer enters Sleep mode
when the computer operates above 60° C. Operation automatically
resumes when the computer cools to below 60° C. Move the
computer to a cooler location.

The Status LED is red, continuous.

• The computer is on, running under battery power, and the charge
level in the battery has reached a critical level. Plug the computer
into an AC/DC power source or install a charged battery.
• The system has encountered a fault and is preventing normal
operation. Contact your local help desk.

The Status LED is red, blinking.

XC6 User’s Handbook

The computer is powered on, running under battery power, and the
charge level in the battery is at a minimum warning level. Plug the
computer into an AC/DC power source or install a charged battery.

Appendix A. Troubleshooting

Table 6

Troubleshooting (continued)

Problem

Possible cause and solution

Display screen is blank or difficult to
read.

• Confirm that the computer is on (the Power icon is displayed
continuously in the Status area).
• The brightness may be set too low, causing the screen to appear too
dark. To change system brightness, press the Fn and Start keys to
open the Xplore menu and adjust the brightness. (See page 28.)
• An external monitor may be selected. Press the Fn and P1 keys to
select the computer display screen. (See page 28.)
• The video time-out may have expired. Tap the display screen to
reactivate the display.
Note: This is a normal, power-saving feature.
• If the Status light is blinking red, the computer is in Sleep mode
because the temperature is below -20° C or above 60° C. When the
temperature returns to a safe operating range, the display screen
automatically comes back on. If possible, move the computer to a
warmer or cooler location.
• If the Status light is continually yellow, the computer is in Sleep or
Hibernate mode. Press the Power On/Off key to resume.

Cursor is not tracking the pen.

Calibrate the pen. See “Calibrating the digitizer” on page 77.

Computer is not responding to the pen.

Connect an external USB keyboard to the computer. If the computer
does not respond to the external keyboard, the application or
operating system may have been corrupted. Press the Reset key.
(See page 33.) If the system responds to a keyboard but not to the
pen, contact your local help desk or reseller for further assistance.

Headphone or speaker volume is too
low.

• The volume may be in Mute mode or set too low. Follow the
instructions in “Adjusting headphone or speaker volume” on
page 48.
• Make sure the volume control in your audio software is set to an
audible level.

An external device is not working with
the computer.

The device may need to be enabled in the computer’s configuration
program (BIOS Setup). Contact your local help desk or reseller.

XC6 User’s Handbook

Using BIOS and AOS Functions

Note: Each button has its
own blue-light LED. No
matter which button you
press, every blue-light LED is
on for about 3 seconds, then
off. When in Shifted mode, all
blue-light LEDs flicker.

Table 7

This appendix explains how to use the application and navigation
buttons with the Basic Input-Output System (BIOS) program and the
Advanced Operating System (AOS) Options menu.
Note: These functions are typically for use only by your system
administrator or by authorized service technicians.

Using BIOS and AOS functions
In Shifted Mode

Button

BIOS Key

Function

BIOS Key

Function

F1 continues message.

Up Arrow

Navigate up through Multi Boot
options and BIOS menus.

Start the BIOS program: When the
computer is booting, press the P2
button and follow the instructions
that appear on the screen.

Down Arrow Navigate down through Multi
Boot options and BIOS menus.

Prompt Windows to select Safe
mode.

Right Arrow

F11
(Lock Fn)

• Press for less than one second for Release
F11 function.
Function

Navigate to the right.
Press once to exit Shifted mode.

• Press longer to enable Shifted
mode.
Start

Display Windows Start menu.

Ctrl+Alt+Del Reboot.

XC6 User’s Handbook

None

Enter

Enter.

Appendix B. Using BIOS and AOS Functions
Disabling the Auto Power feature

Disabling the Auto Power feature
When Auto Power is enabled, the tablet automatically turns on if you
dock it and the following conditions exist:

Note: When the tablet is in
the docking station, it will shut
down or go into Hibernation
or Sleep mode the same as it
does when not in the docking
station.

■

The tablet is off or in Hibernation or Sleep mode.

■

The dock or the tablet is connected to an external power source
(including power applied when a vehicle’s ignition is started).

If you dock the tablet and the tablet is off and no power is present, the
tablet turns on as soon as power is applied.
To disable the Auto Power feature:
1.

When the computer is booting, press the P2 button to access the
BIOS Setup Utility.

Select the Advanced tab.

Disable the Dock with Auto Power On option.

Enabling automatic LCD backlight control
When the LCD backlight control is in manual mode, the ambient light
sensor is disabled and the computer does not automatically control the
screen brightness.
Follow these steps to enable automatic LCD backlight control:

When the computer is booting, press the P2 button to start the
BIOS Setup Utility.

Select the Main tab.

In the LCD Backlight Control drop-down list, select Automatic.

Click OK.

XC6 User’s Handbook

Glossary
Adapter. A device that provides an interface between two dissimilar
electronic devices. For example, the AC adapter modifies the power
from a wall outlet for use by the computer.
Advanced Power Management (APM). A facility consisting of one
or more layers of software that support power management. The APM
software interface enables applications, operating systems, device
drivers, and the APM BIOS to work together to reduce power
consumption.
Alternating Current (AC). Electric current that reverses its direction
of flow at regular intervals.
Analog signal. A signal with characteristics such as amplitude and
frequency that vary in proportion to (are an analog of) the value to be
transmitted. Voice communications are analog signals.
Application. A program that performs specific tasks on your
computer, such as word processing or creating spreadsheets.
BIOS. Programs that contain such basic hardware operations as an
interaction with diskette drives, hard disk drives, and the memory.
Board. A circuit board. An internal card containing electronic
components called chips, which perform a specific function or
increase the capabilities of the system.
Boot. To load a program or operating system into system memory.
Bits Per Second (BPS). In serial transmission, the instantaneous bit
speed with which a device or channel transmits a character.
Card. Synonym for board; see board.
Compact Disk-Read Only Memory (CD-ROM). Stores data on
metal-plated plastic discs.

XC6 User’s Handbook

Appendix C. Glossary

Compatibility. 1.The ability of one computer to accept and process
data in the same method as another computer without modifying the
data or the media upon which it is being transferred. 2.The ability of
one device to connect or communicate with another system or
component.
Configuration. The specific combination of hardware components of
the computer, and their operating status. The configuration of your
computer includes predefined memory, type and speed of
microprocessor, type of and size of hard disk drive, etc.
Default. The preset parameter value automatically selected by the
computer when you or a program do not provide instructions.
Device driver. A program that controls communication between a
specific peripheral device (such as a printer or the pen/stylus) and the
computer.
Disk drive. The physical device that enables the computer to read
from, and write to, a disk.
Display. An image-producing device used to view computer output.
Double-click. To press and release the pen/stylus twice within a time
frame you define, without moving the pointer off the choice.
Hardware. The physical electronic and mechanical components of a
computer system. typically, the computer itself, CPU, memory, etc.
Hertz. A unit of wave frequency that equals one cycle per second.
Interface. 1. Hardware and/or software components used specifically
to connect one computer or device to another. 2. To physically
connect one system or device to another to exchange information. 3.
The point of contact between user, the computer, and the program (for
example, the pen/stylus or a menu).
JBOD. Two drives that appear in Window as two drives, Drive C and
Drive D.

XC6 User’s Handbook

Appendix C. Glossary

Kilobyte (KB). A unit of 1024 bytes measuring storage space,
typically in memory or on storage media such as a diskette or hard
disk drive.
Local area network (LAN). Assembly of separate computers into an
integrated network that connects the various computers together and
to common devices such as printers and fax machines.
Light Emitting Diode (LED). A semiconductor device that emits
light when a current is applied.
Liquid Crystal Display (LCD). liquid crystal sealed between two
sheets of glass coated with transparent conducting material. Applying
a voltage between the glass sheets darkens the liquid crystal to
provide contrast to lighted portions of the display.
Megabyte (MB). A unit of data storage equal to 1024 kilobytes.
Megahertz (MHz). a unit of wave frequency that equals 1 million
cycles per second.
Modem. A device that connects your computer to a telephone line,
allowing it to communicate with another computer at another
location.
Pen. See stylus.
Peripheral device. An input/output device that is external to the
central processor and/or main memory such as a printer or scanner.
Pixel. Picture elements (tiny dots) that compose a screen image.
Port. The electrical connection through which the computer sends
and receives data to and from devices or other computers.
Program. A set of instructions a computer can execute to tell the
system what to do and how to do it.
RAID 0. Two drives appear in Windows as one larger drive (two
80GB drives appear as one 160GB drive).

XC6 User’s Handbook

Appendix C. Glossary

RAID 1. One drive has information mirrored to a duplicate drive. For
example, information from one 80GB drive is mirrored to another
80GB drive. The two drives appear in Windows as a single drive.
Random Access Memory (RAM). A hardware component of your
computer that temporarily stores active program code and data.
Reset. The act of hard stopping/shutting down the operating system.
Resolution. The number of pixels displayed on the screen. A higher
resolution provides greater clarity and allows more information to be
displayed on the screen at once.
Restart. Resetting a computer without turning it off (also called
warm boot or soft reset).
Resume. The act of returning the computer to an active, operational
state.
Read Only Memory (ROM). The portion of your computer’s
memory that contains permanent instructions, and which cannot be
modified.
Sleep mode. A power conservation mode in which electrical current
is removed from most components of the computer.
Solid State Drive (SSD). A sealed mass storage device used for
storage and fast retrieval of programs and data. The SSD is contained
in a drive cartridge for easy removal.
Status Indicator (LED). a light above the LCD screen which
indicates the current status of a particular device or hardware
component.
Stylus. A writing instrument. For pen computers, the stylus is used to
interface with the LCD and digitizer.

XC6 User’s Handbook

Appendix C. Glossary

Subscriber Identity Module (SIM). A smart card inside a GSM
(Global System for Mobile communications) cellular device that
encrypts voice and data transmissions and stores data about the
specific user so that the user can be identified and authenticated by
the network supplying the phone service. A SIM can be moved from
one device to another and/or different SIMS can be inserted into any
GSM radio.
Universal Serial Bus (USB). A serial interface that enables
communication between devices and the computer.

XC6 User’s Handbook

Hardware Specifications

Physical
Dimensions

11.20” x 8.25” x 1.6” (WxHxD)
283.9mm x 209.3mm x 40.8mm

Weight

5.40 lbs. (2.45 kgs)*

Processing
CPU / chipset *

Intel® Core® i7-4650IU

Intel Core i5-4300U

Intel Celeron® 2980U

Cores / threads

2/4

2/2

Clock / turbo speed

1.7 / 3.3 GHz

1.9 / 2.9 GHz

1.6 GHz

L2 cache

4 MB

3 MB

2 MB

Graphics

Intel HD Graphics 5000

Intel HD Graphics 4400

Intel HD Graphics

Graphics frequency

200 MHz - 1.1 GHz

200 MHz - 1.0 GHz

Number of displays supported

Intel vPro technology

Yes

Intel Hyper-Threading
technology

Yes

Trusted Execution technology

Yes

* Varies according to your computer’s configuration.

XC6 User’s Handbook

Appendix D. Hardware Specifications

Memory/storage
Main RAM

• 4 GB, 8 GB, or 16 GB DDR III RAM (4GB standard)
• 144-pin SODIMM modules

BIOS ROM

16 Mb

Storage

60 GB SSD, 120 GB SSD or 240 GB SSD, single or dual; RAID 0/1 and AHCI support

* Varies according to your computer’s configuration.

Display
Display

• 10.4” TFT XGA (1024x768), 16M colors, 32-bit True-color LCD
• Active digitizer / pen
• Advanced matrix resistive touch panel with ten-finger multi-touch
• Dual mode operation of digitizer and touch panel
• Brightness: 100 levels
• 1300 nits max before touch (sunlight-readable)
• 340 nits max before touch (indoor-readable)
• Viewing angle:
- Horizontal: 80 degrees
(typical, contrast ratio > 10)
- Vertical: 80 degrees
(typical, contrast ratio > 10)
• Contrast Ratio: Typ. 600:1, Min 400:1

XC6 User’s Handbook

Appendix D. Hardware Specifications

User Interface
Wireless Radio Bays

• One M.2 PCI Express slot for WWAN (4G / LTE)
• One half mini-PCI Express slot for WiFi

Integrated Interfaces

• DC-in
• USB 3.0 (2)
• Microphone / headset combination jack
• LAN (RJ-45)
• 9-pin serial port (standard)
or
15-pin D-SUB VGA connector (optional)
or
HDMI connector (optional)

KeyPad / User Controls

• Application buttons with primary and secondary functions
• Power On/Off/Suspend/Resume button
• Emergency Shutoff/Reset button

Audio

• Realtec ALC283
• On-board microphone with noise cancellation
• On-board integrated stereo speakers (1W each)

Status Indicators

XC6 User’s Handbook

Power, Charge, DC-in, Warning, Camera Active

Appendix D. Hardware Specifications
Power
Main Battery

• 10 cell, Xplore part number 11-01022
• Removable Lithium Ion
• 7.4V @ 10.625 Ah (80.75 Whr)
• Warm-swappable
• Recharge time: 2.5 hours (100%)
• Life: Up to 8 hours. (Battery life is dependent on operating system, power
management, and applications in use.)
• Suspend life: Min. 67 days
• Off state: Approximately 90 days

Bridge Battery

• 6-cell Li Ion, 45mAh
• Life: (with Suspend-to-RAM on bridge battery only): 3 to 5 minutes from full
charge

AC Adapter

• Xplore part number 11-50048
• FSP part number FSP065-REB
• Power adapter, 100-240V AC input (auto-sensing), 19V DC @ 3.42A output,
ROHS, Energy Star, CE, UL, TUV

XC6 User’s Handbook

Appendix D. Hardware Specifications

Environmental
Temperature

• Operating:
-7o to 140o F (-20o to 60o C) (XC6 minimum is -49o F,-45o C)
• Storage:
-40o to 167o F (-40o to 75o C)

Humidity

0% to 95% non-condensing

Shock/Drop

Four-foot drop to concrete, all surfaces, edges and corners

Vibration

0.04g^2/Hz, 20 Hz - 1000 Hz
-6dB/octave 1000 Hz - 2000 Hz

Enclosure Class

Blowing rain:
4”/hr, 40 mph wind and
MIL-STD-810G Method 506.5 Procedure 1
Ingress protection:
IEC (60529) ingress tested to an IP67 standard
Sand and dust:
Particle size < 149 µm, 10 + 7 g/m3 particle density 1.5 m/s to 8.9 m/s wind speed
MIL-STD-810G Method 506.5 Procedure 1
Salt Fog:
5% saline for 48 hr (12 hr wet, 12 hr dry, 2 cycles)
MIL-STD-810G Method 506.5
Contamination by fluids:
Detergents, brake fluid, aromatic hydrocarbons
MIL-STD-810G Method 506.5
Solar radiation:
1120 W/m2 (355 Btu/ft2/hr) UVB @ 50° C, 7x24 hr cycles
MIL-STD-810G Method 506.5

XC6 User’s Handbook

Appendix D. Hardware Specifications

Agency approvals
EMC

• CFR 47, FCC part 15B, IC ICES-003
• European Union Directive 2004/108/EC RTT&E

Safety

• TUV Bauart, RoHS, 2002/95/EC, WEEE
• IEC600950-1 2nd Ed., EN60950-1 2nd Ed., UL60950-1 2nd Ed.
• ETL Listed: ANSIISA-12.12.01-2007, C22.2 No. 213
• UL1604

Operating system
Operating Systems

• Microsoft Windows 7 Professional, 32-bit, English
• Microsoft Windows 7 Professional, 64-bit, English
• Microsoft Windows 8 Professional, 64-bit, English

XC6 User’s Handbook

Agency Notices
FCC notices
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Modifications not expressly approved by Xplore Technologies could void this
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

XC6 User’s Handbook

Appendix E. Agency Notices

IC regulations
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement."
The device could automatically discontinue transmission in case of absence
of information to transmit, or operational failure. Note that this is not intended
to prohibit transmission of control or signaling information or the use of
repetitive codes where required by the technology.
The device for the band 5150-5250 MHz is only for indoor usage to reduce
potential for harmful interference to co-channel mobile satellite systems; the
maximum antenna gain permitted (for devices in the bands 5250-5350 MHz
and 5470-5725 MHz) to comply with the e.i.r.p. limit; and The maximum
antenna gain permitted (for devices in the band 5725-5850 MHz) to comply
with the e.i.r.p. limits specified for point-to-point and non point-to-point
operation as appropriate, as stated in section A9.2(3). In addition, High-power
radars are allocated as primary users (meaning they have priority) of the band
5250-5350 MHz and this radar could cause interference and/or damage to LELAN devices.
The County Code Selection feature is disabled for products marketed in the
US/Canada. For product available in the USA/ Canada markets, only channel
1~11 can be operated. Selection of other channels is not possible.
IC radiation exposure statement
This EUT is compliance with SAR for general population/uncontrolled
exposure limits in IC RSS-102 and had been tested in accordance with the
measurement methods and procedures specified in IEEE 1528.

XC6 User’s Handbook

Appendix E. Agency Notices

RF exposure
Tests for SAR are conducted using standard operating positions specified by
the FCC with the tablet PC transmitting at its highest certified power level in
all tested frequency bands. Although the SAR is determined at the highest
certified power level, the actual SAR level of the tablet PC while operating
can be well below the maximum value. This is because the tablet PC is
designed to operate at multiple power levels so as to use only the power
required to reach the network. In general, the closer you are to a wireless base
station antenna, the lower the power output.
Before a tablet PC model is available for sale to the public, it must be tested
and certified to the FCC that it does not exceed the limit established by the
government-adopted requirement for safe exposure. The tests are performed
in positions and locations (e.g., on the body) as required by the FCC for each
model. (Body-worn measurements may differ among tablet PC models,
depending upon available accessories and FCC requirements). While there
may be differences between the SAR levels of various tablet PCs and at
various positions, they all meet the government requirement for safe
exposure.
This device was evaluated and shown to comply with FCC SAR guidelines.
Avoid covering or holding antennas when transmitting. Antenna locations are
shown in the following figure.
Antennas

Bluetooth
antenna

XC6 User’s Handbook

Appendix E. Agency Notices

Health and Safety Information
Exposure to Radio Frequency (RF) Signals
Your wireless tablet PC is a radio transmitter and receiver. It is designed and
manufactured not to exceed the emission limits for exposure to radio
frequency (RF) energy set by the Federal Communications Commission of
the U.S. Government as well as the RTT&E directive. These limits are part of
comprehensive guidelines and establish permitted levels of RF energy for the
general population. The guidelines are based on the safety standards
previously set by both U.S. and international standards bodies:
■
American National Standards Institute (ANSI) IEEE. C95.1-1992
■
National Council on Radiation Protection and Measurement (NCRP).
Report 86. 1986
■
International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1996
■
Ministry of Health (Canada), Safety Code 6. The standards include a
substantial safety margin designed to assure the safety of all persons,
regardless of age and health.
■
European Union RTT&E Directive for SAR
The exposure standard for wireless mobile tablet PCs employs a unit of
measurement known as the Specific Absorption Rate, or SAR. The SAR limit
set by the FCC is 1.6W/kg. The SAR limit set by the RTT&E is 2.0W/kg.
Note: In the U.S. and Canada, the SAR limit for mobile tablet PCs used by
the public is 1.6 watts/kg (W/kg) averaged over 1 gram of tissue. In Europe the
SAR limit for mobile table PCs used by the public is 2.0 watts/kg (W/kg)
averaged over 10 grams of tissue.The standard incorporates a substantial
margin of safety to give additional protection for the public and to account for
any variations.

DOC (Industry Canada Notices)
Notice to Users of Radio and Television
This Class B digital apparatus meets all requirements of Canadian
Interference-Causing Equipment Regulations per the ICES-003
CET appareil numérique de la class B respecte toutes les exigence du
Réglement sur le matérial brouilleur du Canada.

XC6 User’s Handbook

Appendix E. Agency Notices

Notice to Users of the Canadian Telephone Network
Notice: This equipment meets the applicable Industry Canada Terminal
Equipment Technical Specifications. This is confirmed by the registration
number. The abbreviation, IC, before the registration number signifies that
registration was performed based on a Declaration of Conformity indicating that
Industry Canada technical specifications were met. It does not imply that
Industry Canada approved the equipment.

Before connecting this equipment to a telephone line the user should ensure
that it is permissible to connect this equipment to the local telecommunication
facilities. The user should be aware that compliance with the certification
standards does not prevent service degradation in some situations.
Repairs to telecommunication equipment should be made by a Canadian
authorized maintenance facility. Any repairs or alterations not expressly
approved by Xplore or any equipment failures may give the
telecommunication company cause to request the user to disconnect the
equipment from the telephone line.
Notice: The Ringer Equivalence Number (REN) for this terminal equipment is
0.0. The REN assigned to each terminal equipment provides an indication of
the maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the Ringer Equivalence
Numbers of all the devices does not exceed five.

UL Notice
This unit requires an AC adapter to operate. Use only UL Listed
Class 2 Adapters with an output rating of 19 VDC, with a current of 3.75 A.
AC Adapter output polarity:

For authorized repair technicians only



XC6 User’s Handbook

WARNING
For continued protection against risk of fire, replace only with the same
type and rating fuse.

Appendix E. Agency Notices



WARNING
Danger of explosion if Lithium (clock) battery is incorrectly replaced.
Replace only with the same equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer’s instruction.
System disposal
In the event of system disposal, observe the following information regarding
proper procedures in the State of Vermont.
The liquid crystal display (LCD) lamps used in this system contain mercury.
In the event of system disposal, be sure to follow local guidelines.

Intel Dual Band Wireless-AC 7260 country-specific-compliance
statements
Hereby, Xplore Technologies, declares that the Intel Dual Band Wireless-AC
7260 complies with the essential requirements and other relevant provisions of
Directive 1999/5/EC. This equipment is marked with the CE symbol and can
be used throughout the European community.
Sierra EM7305 country-specific compliance statements
Hereby, Xplore Technologies, declares that the Sierra EM7305 complies with
the essential requirements and other relevant provisions of Directive
1999/5/EC. This equipment is marked with the CE symbol and can be used
throughout the European community.
Intel Dual Band Wireless-AC 7260 - Regulatory USA

100

XC6 User’s Handbook

Appendix E. Agency Notices

Intel Dual Band Wireless-AC 7260 - Regulatory Europe

XC6 User’s Handbook

101

Appendix E. Agency Notices

102

XC6 User’s Handbook

Environmental Policy and Recycling Program

Environmental policy
Xplore Technologies is committed to managing health, safety and
environmental (HS&E) matters as an integral part of our business. In
particular, it is our policy to assure the HS&E integrity of our
processes and facilities at all times and at all places. We will do so by
adhering to the following principles:
Compliance
We will comply with applicable laws and regulations and will
implement programs and procedures to assure compliance.
Compliance with HS&E standards will be a key ingredient in the
training, performance reviews, and incentives of all employees.
Risk reduction, prevention, and resource management
We will seek opportunities, beyond compliance requirements, for
reducing risk to human health and the environment, and we will
establish and meet our own HS&E quality standards where
appropriate.
We will employ management systems and procedures specifically
designed to prevent activities and/or conditions that pose a threat to
human health, safety, or the environment. We will look for ways to
minimize risk and protect our employees and the communities in
which we operate by employing clean technology, including safe
technologies and operating procedures, as well as being prepared for
emergencies.
We will strive to minimize releases to the air, land, or water through
use of cleaner technologies and the safer use of chemicals. We will
minimize the amount and toxicity of waste generated and will ensure
the safe treatment and disposal of waste. We will manage scarce
resources, such as water, energy, land, and forests in an
environmentally sensitive manner.

XC6 User’s Handbook

103

Appendix F. Environmental Policy and Recycling Program
Take back and recycling program

Communication
We will communicate our commitment to HS&E quality to our
employees, vendors, and customers. We will solicit their input in
meeting our HS&E goals and in turn will offer assistance to meet
their goals.
Continuous improvement
We will measure our progress as best we can. We will review our
progress at least on an annual basis. We will continuously seek
opportunities to improve our adherence to these principles, and will
periodically report progress to our stakeholders.

Take back and recycling program
Send us your unwanted Xplore products and/or batteries or find a
recycling center near you. If your old Xplore product and/or batteries
have no value or you want to recycle in a socially and
environmentally responsible manner, go to http://www.xploretech.com;
then select Customer Support and submit a technical support request
as follows:
1. Navigate to the Technical Support form and enter information in
the form’s fields.
2. Under Message, type I want to recycle my product.
3. Click Submit.
An Xplore Technologies specialist will contact you with shipping
instructions.
Alternatively, you can leave your unwanted Xplore products at a local
recycling center. For batteries, Xplore Technologies has partnered
with Call2Recycle® (http://www.call2recycle.org/). Call2Recycle is
a program of the Rechargeable Battery Recycling Corporation
(RBRC) that promotes environmental sustainability by providing free
battery and cell phone recycling in North America. RBRC is a
501(c)4 nonprofit public service organization.

104

XC6 User’s Handbook

Appendix F. Environmental Policy and Recycling Program
Environmental and Sustainability Corporate Report

If you prefer to have Xplore Technologies recycle your battery packs,
submit a technical support request as described above.
For the return of any Xplore product other than batteries, Xplore
Technologies has partnered with R2 Solutions (http://
www.r2solutions.org/). R2 Solutions (R2S) is a non-profit
organization established to promote R2 practices as a major step
towards making responsible electronics recycling business as usual
across the United States and abroad. To find a location near you, go to
R2 certified recycler locations (http://asoft552.accrisoft.com/
certified/electronic-recyclers-with-r2-certified-facilities/).
If you do not have access to the Internet, contact our technical support
at (866) 296-8541 ext. 222.

Environmental and Sustainability Corporate Report
As the manufacturer of the world’s most advanced ruggedized tablet
PC and peripherals, Xplore Technologies is recognized for the
efficient design and manufacturing of it products. In our inaugural
Environmental and Sustainability Corporate Report we outline our
plans and aspirations to sustain our environment. As you review this
report, we welcome your candid feedback. We know that CSER is a
journey and your input will help us along the way.
In 2011, Xplore Technologies Corporation of America established the
Xplore Technologies Environmental committee to proactively work
with stakeholders including customers, nongovernmental
organizations (NGOs), and other interested groups on environmental
issues. As a result of the committee's work, we have implemented
initiatives to improve our performance across the spectrum of
corporate environmental responsibility issues. Our progress on
implementing these issues is outlined in this report.
Although the Xplore Technologies Environmental committee has
only been active since 2012, we have always cared for the
environment and this has been a core value since Xplore
Technologies was founded more than 15 years ago. We are proud of
our accomplishments to date and, we are committed to continuously
improve in the future.

XC6 User’s Handbook

105

Appendix F. Environmental Policy and Recycling Program
Environmental and Sustainability Corporate Report

Publishing this report is a significant step toward the goal of
becoming an environmental sustaining leader of our industry. Going
forward, we will persist to perfect our environmental performance
and transparency. We will also leverage our role as an industry leader
and actively support international organizations and industry
associations working to improve environmental conditions.
The Xplore Technologies 2012 Environmental and Sustainability
Corporate Report is located at http://www.xploretech.com/
environment. To obtain the report, click Environmental Sustainability
Report 2012. Feel free to save this to your personal files. If you do not
have access to the Internet, call Xplore technical support at (866) 2968541 ext. 222 and request that a digital copy be sent to your email
address.

106

XC6 User’s Handbook

Index
A

air flow vents, location 22
ambient light sensor
location 19
antenna covers, location 21
Auto Light sensor, disabling 45
Auto Power feature, disabling 82

Environmental and Sustainability Corporate
Report 105
Environmental policy 103

B
battery pack
charge time 52
charging 51
checking the charge 51
conserving power 59
installing 54
location 21
removing 52
battery release latch, location 21
BIOS Setup Utility, using 81
Bluetooth toggle 30

C
camera hot key 30
Charm bar, open 30
convection air flow cover, location 21

D
digitizer
calibrating 77
using to perform mouse functions 39
double-click, performing with pen 39
dragging and dropping, performing with pen 39

CX6 User’s Handbook

G
GPS, toggle 30

H
headphone volume, adjusting 48
Hibernation mode
description 34
hot keys, programming 63
hot keys, programming,
see keys, programming hot keys

K
Kensington lock slot, location 22
keys
Ctrl-Alt-Del, description 29
descriptions 29
Function
description 29
location 28
Function mode hot key combinations
descriptions 30
P1, location 28
P2, location 28
P3, location 28
Power On/Off/Sleep/Resume
location 58

107

Index

programming hot keys 63
to perform other key functions 70
to perform pre-defined functions 68
quick-start diagram 28
Screen Rotation, location 28

L
LAN connector, location 23
LCD backlight
disabling automatic control 45
enabling manual control 82
LEDs, Status LED meanings 26
left button click, performing with pen 39
local area network (LAN), connecting to 47
logging on 29

M
microphone
connecting external 48
location 19
volume, adjusting 48
monitor
activating 49
connecting 49
mouse functions, performing 39

P
pen
double-click speed, changing 39
dragging and dropping 39
holder, location 21
location 21
performing a double-click 39
performing a right-click 39
performing left button click 39
positioning in holder 40
replacing 76
tether, using 40
108

Power (On/Off)/Backlight (On/Off)/Sleep/
Resume key, location 58
power connector, location 23
Power On/Off/ Suspend/Resume key
location 22
power use, managing 55
projection panel
activating 49
connecting 49

Q
quick-start guide 28

R
recycling program 104
Reset switch
location 19
using 33
resuming operation 37
right-click, performing with pen 39
RJ-45 connector 23
rotate screen 30

S
screen
protecting 75

rotating 30
screen orientation
changing 43
landscape 43
portrait 43
screen protector
installing 76
removing 76
replacing 76

CX6 User’s Handbook

Index

serial port
compatible devices 50
location 50
Sleep mode
ending 37
starting 35
Sleep mode, description 34
Sleep mode, hot keys 30
speaker volume, adjusting 48
speakers, location 19
storing the computer 75
support, contacting 17
suspending operation 35

volume
adjusting headphone 48
adjusting microphone 48
adjusting speaker 48

W
Windows Task Manager, launching 29

X
XPL expansion module, connecting 50
XPL2 port 22 25
Xplore Technologies, contacting 17

T
tablet
accessories 15
preventing overheating 74
protecting from damage 73
storing 75
transition between open apps 30
troubleshooting 79
turning off the computer 32
turning on the computer 31

U
USB port, location 23
USB-compatible device, connecting 47

V
video output
changing from monitor to computer 49
changing to monitor 49
video output, change 30
video, hot keys 30

CX6 User’s Handbook

109

110

CX6 User’s Handbook

Xplore XC6 User Guide Instruction Manual UG EN

Navigation menu

Versions of this User Manual:

Views

Navigation