zBoost ZB570-PCS-CEL Part 20 Wideband Consumer Booster User Manual ZB560P Manual indd
zBoost, LLC Part 20 Wideband Consumer Booster ZB560P Manual indd
zBoost >
Contents
- 1. ZB450_Manual
- 2. ZB540_Manual
- 3. ZB540iP_Manual
- 4. ZB545_Manual
- 5. ZB545M_Manual
- 6. ZB545x_Manual
- 7. ZB560P_Manual
- 8. ZB560SL_Manual
- 9. ZB560Y_Manual
- 10. ZB645-Platinum_Manual
- 11. ZB645SL_Manual
- 12. ZB645SL-CM_Manual
- 13. ZB645-Ultra-Platinum_Manual
- 14. ZBC745_Manual
- 15. ZBC745SL_Manual
- 16. ZBC745SL-CM_Manual
- 17. ZBC3500_Manual
ZB560P_Manual
zBoost REACH ZB560P Manual zBoost® products have a 30-day money back guarantee when purchased directly from zBoost. If product is purchased from a reseller or third party, the purchaser is subject to the policies of the third party. 2 year manufacturer warranty. Warranty registration at www.zBoost.com v.0314 zBoost® REACH ZB560P Manual zBoost® REACH ZB560P Manual FCC Requirements About zBoost® zBoost, a leader in cell phone signal boosters manufactures zBoost, the award-winning line of cell phone signal boosters that enhance the performance of your cell phone, smartphone and wireless data card. Compatibility – Dual Band zBoosts are compatible with 800 MHz and 1900 MHz regardless of technology- including CDMA and GSM. This is a CONSUMER Device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. AT&T, Sprint, T-Mobile, Verizon and 90 additional carriers have already given consent for all consumers to use this device. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. Uses patented technologies and protects the carrier network. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. 2-year manufacturer warranty – Warranty registration at www.zBoost.com. FCC Information WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. FCC ID: SO4ZB570-PCS-CEL FCC contact information: www.fcc.gov/signal-boosters/registration. Warning: Changes or modifications to this device not expressly approved by zBoost could void the user’s authority to operate the equipment. Warning Any product modifications that use unauthorized antennas, cables, and/or coupling devices is no longer FCC compliant and will void the product warranty. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element (antenna) shall be installed such that a minimum separation distance of 20cm (8in) is maintained from all persons. Industry Canada Regulations IC ID: 5544A-ZB570PCSCEL This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. RF Exposure: The manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device. ii zBoost® REACH ZB560P Manual Cet appareillage numérique de la classe [B] répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. Le fabricant nominale de la puissance de sortie de ce matériel est simple transporteur. Pour les situations lorsque plusieurs signaux porteurs sont présents, l’évaluation devrait être réduite de 3.5 dB, en particulier lorsque le signal de sortie est ré-émise et peut provoquer des interférences adjacentes à la bande utilisateurs. Ce pouvoir est de la réduction par le biais de la sortie d’alimentation ou la réduction de gain et non par un atténuateur à la sortie du dispositif. Please note: This unit has been approved for use in Canada under RSS 131, however, consent for the use of this device to improve cellular or PCS coverage, must be obtained through your cellular or PCS provider, prior to placing the unit in operation. Please refer to the Industry Canada document CPC 2-1-05, Section 6.1 available or viewable at: http://www.ic.gc.ca/epic/site/smt-gst.nsf/en/sf08942e.html Safety and Product Warranty Information zBoost® REACH ZB560P Manual Package Contents Before you begin, make sure all of the following parts came with your zBoost ZB560P. Literature Contents: ① Setup overview Product Contents: ② zBoost Base Unit ② ③ Indoor Antenna ④ Power Supply Copyright Notice This manual is copyrighted. All rights reserved. This manual, whole or in part, may not be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine readable form for distribution. This manual whole or in part, may not be modified without prior consent, in writing, from zBoost. Copyright © 2014 by zBoost. ⑤ RG-6 Coax Cable, 50 ft. ③ ⑥ External Antenna ⑦ Mounting Hardware ④ Trademarks zBoost, the zBoost logo, Wireless Extenders, Wi-Ex, the Wi-Ex logo, and Extending Cell Zones are registered trademarks of zBoost. Safety Guidelines ⑤ In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element (antenna) shall be positioned such that a minimum separation distance of 8 inches (20cm) is maintained between the radiating element and the user and/or general population. ⑥ Limited Liability In no event shall zBoost be liable for any direct, indirect, special, punitive, incidental, exemplary or consequential damages, or any damages, whether in an action under contract, negligence, or any other theory, arising out of or in connection with the set up of, use of, inability to use, or performance of the information, services, products, and materials available from this manual. These limitations shall apply notwithstanding any failure of essential purpose of any limited remedy. Because some jurisdictions do not allow limitations on how long an implied warranty last, or the exclusion or limitation of liability for consequential or incidental damages, the above limitations may not apply to you. For full warranty guidelines, see page 13. iii ⑦ iv zBoost® REACH ZB560P Manual zBoost® REACH ZB560P Manual Accessories Table of Contents The following accessories are authorized for this zBoost product. Please see our website for complete selection. To order, call 1-800-871-1612 or visit, www.zBoost.com FCC Requirements........................................................................................................................i Broadcast Antennas - Indoor FCC Information ...........................................................................................................................ii CANT-0032 Indoor Broadcast Antenna, Omni Whip Direct to Booster, Black, CEL-PCS (1 dBi) Industry Canada Regulations .......................................................................................................ii CANT-0034 Indoor Broadcast Antenna, Omni Whip Direct to Booster, White, CEL-PCS (1 dBi) Safety and Product Warranty Information................................................................................... iii CANT-0039 Indoor Broadcast Antenna, Omni Whip Direct to Booster, Black, Wide- Band, LTECEL-AWS-PCS (1 dBi) Copyright Notice ......................................................................................................................... iii YX027-PCS-CEL* Indoor Broadcast Antenna, Directional Panel w/ F-Female Connector, CEL-PCS (6 / 8 dBi) Trademarks ................................................................................................................................. iii Safety Guidelines ........................................................................................................................ iii Limited Liability ........................................................................................................................... iii YX027-F* Indoor Broadcast Antenna, Directional Panel w/ F-Female Connector, CEL-PCS (6 / 8 dBi) Package Contents ........................................................................................................................ iv YX050-PCS-CEL Indoor Broadcast Antenna, Ceiling Mount Omni w/ TNC-Male Connector, CEL-PCS (1 / 2 dBi) Table of Contents .......................................................................................................................... 1 YX052 Indoor Broadcast Antenna, Ceiling Mount Omni w/ F-Female Connector, LTE-CELAWS-PCS (1 / 2 dBi) External Antennas - Outdoor Accessories ................................................................................................................................... v Overview ........................................................................................................................................ 2 Why Indoor Signals Can Be Weak ............................................................................................... 2 Preparing to Set Up Your zBoost Product.................................................................................... 3 CANT-0028 Outdoor External Antenna, Directional Low Profile Panel, CEL-AWS-PCS (6 / 8 dBi) Tools Needed .............................................................................................................................. 3 CANT-0031 Window-mount External Antenna for YX540 zBoost Metro, Directional Panel, CELPCS (6 / 8 dBi) Check for Signal Strength ........................................................................................................... 3 CANT-0033 Outdoor External Antenna, Small Omni, CEL-PCS (3 / 5 dBi) CANT-0036 Outdoor External Antenna, Omni with Industrial Casing, CEL-PCS (3 / 5 dBi) CANT-0040 Outdoor External Antenna, Wide-Band Omni Directional, LTE-CEL-AWS-PCS (3 / 5 dBi) CANT-0041 Outdoor External Antenna, Wide-Band Directional Log Periodic, LTE-CEL-AWS-PCS (8 / 10.5 dBi) CANT-0042 Outdoor External Antenna, Wide-Band Directional Log Periodic, LTE-CEL-AWS-PCS (10 / 12 dBi) FIRST: Mount the External Antenna............................................................................................. 6 YX021-CEL Outdoor External Antenna, Directional Panel, CEL (8 dBi) SECOND: Place the zBoost Base Unit where you want to create a Cell ZoneTM ......................... 6 YX023-PCS Outdoor External Antenna, Directional Panel, PCS (13 dBi) THIRD: Run the Coaxial Cable .................................................................................................... 7 YX026-CEL Outdoor External Antenna, Directional 3 foot Yagi with 12 Elements, CEL (11 dBi) FOURTH: Connect zBoost Base Unit to Power ........................................................................... 7 YX039-PCS-CEL Outdoor External Antenna Kit, Two Directional Panels with Combiner, CEL-PCS (8 / 13 dBi) Coax Cable - To be used in addition to the cable included in your kit YX030-0W8 8 Inch Window Entry Cable with F-Female Connectors YX030-15W 15 Foot RG-6 Coaxial Extension Cable with F-Male Connectors YX030-35W 35 Foot RG-6 Coaxial Extension Cable with F-Male Connectors YX030-50W 50 Foot RG-6 Coaxial Cable with F-Male Connectors YX031-10W 10 Foot RG-8X Coaxial Cable with TNC-Male & Female Connectors (Booster to Distribution Antenna) YX031-100W 100 Foot Low Loss RG-11 Coaxial Cable with F-Male Connectors Antenna Bracket Assembly ......................................................................................................... 4 Additional Cable Requirements ................................................................................................... 4 Grounding the External Antenna.................................................................................................. 5 Securing Cable with a Drip Loop ................................................................................................. 5 Power Requirements ................................................................................................................... 5 Setting Up Your zBoost Signal Booster ....................................................................................... 6 Antenna Bracket Assembly ......................................................................................................... 6 Confirm That Your zBoost is Working Properly ............................................................................ 8 Improving Your Coverage Area ..................................................................................................... 9 zBoost Base Unit Light Indicators .............................................................................................. 10 Technical Specifications ..............................................................................................................11 Frequently Asked Questions ...................................................................................................... 12 Warranty Information .................................................................................................................. 13 Accessories YX012 Outdoor External Antenna Grounding Kit * The FCC requires that this panel antenna has a minimum horizontal separation of 6 feet (2 meters) from other CMRS (commercial mobile radio service) devices. zBoost® REACH ZB560P Manual zBoost® REACH ZB560P Manual Overview Thank you for choosing zBoost! You will now be able to use your cell phone INSIDE your home. Gone are the days when you had to go to the window upstairs or walk outside to use your cell phone. Like a skylight that brings sunlight into your home, zBoost transports and amplifies the outdoor signal into your home. By following the easy instructions in this User Manual, you will be Extending Cell Zones™ into your home. Why Indoor Signals Can Be Weak There are several obstacles that can contribute to the poor reception you receive in your home: 1. Location of the Cell Phone Tower in Relation to Your Home While cell phone providers have tried to place cell phone towers to provide the best overall coverage, local ordinances and terrain features can impose restrictions on where these towers can be placed, thus, limiting the signal strength available at your location. 2. Obstructions Caused by Buildings, Terrain and Trees Cell phone signals can be completely blocked or reflected by buildings, walls, trees, hills and other terrain features resulting in low signal strength. 3. Energy Efficient Windows Energy efficient windows contain a metal film that can affect signal penetration into the house. Preparing to Set Up Your zBoost Product Tools Needed The following tools are needed to set up zBoost: • #2 Phillips screwdriver • Cellular phone operating in the band supported by your zBoost unit • Drill (may be required for outdoor or attic antenna placement) Check for Signal Strength Before placing a zBoost in your home, make sure that you can place calls on the outside of your home, in the attic, at roof level or wherever you plan to place the External Antenna. zBoost can only bring signal into your home when signal reaches the External Antenna. If there is no signal, the zBoost will not work for you. Using your cell phone, place a call from an outdoor location to confirm that enough signal is present to complete the call. If a weak signal is available at ground level, check the signal strength in your attic or at roof level location where the signal will likely be stronger and where the External Antenna can be placed for best performance. If you can reliably make and receive calls outside your home, then zBoost can bring the signal into your home. If only one signal bar is displayed on your cell phone outside, indoor coverage will be limited to one small room. We recommend placing the External Antenna outside and/or purchasing a zBoost upgrade External Antenna for increased coverage (see page v). Note Cell phone signal bars are approximate and vary from phone to phone. The number of bars can fluctuate widely, depending on the location of the phone, the position or angle of the phone, weather, etc. Most cell phone signal meters update every 6 to 10 seconds. An increase of only one bar typically indicates a 4x to 10x signal increase. zBoost® REACH ZB560P Manual Before installing, please note the following important factors in determining your zBoost performance: • • At least 15 vertical feet is needed between the External Antenna (receives the outside signal) and the Indoor Antenna (rebroadcasts the signal indoors). Separation less than 15 vertical feet will result in decreased performance. See illustration below. Keep the External Antenna at least 3 feet above any metal. See page 6, Setting Up Your zBoost Signal Booster, for additional information. zBoost® REACH ZB560P Manual Grounding the External Antenna If you decide to place the External Antenna outdoors, it must be properly grounded. (See page iv for a recommended grounding kit). The set up must be in accordance with Article 810 of the National Electric Code (NEC). A listed antenna discharge unit must be provided for the lead-in coaxial cable per NEC article 8.10.20 or the shield of the coaxial cable must be permanently and effectively grounded in accordance with NEC article 8.10.21. Please consult a professional installer or electrician for more information. (See page v). Note 15 ft. of Vertical Separation Minimal Performance Avoid placing the External Antenna near metal such as wiring, A/C ducts, metal siding, truss plates, etc. When connecting the cable to the antenna, run the cable straight down from the antenna. Avoid draping the coax near the antenna. Best Performance (Recommended) Securing Cable with a Drip Loop Antenna Bracket Assembly IMPORTANT: Incorrectly mounting the External Antenna to the mounting bracket will impede performance. Ensure that the External Antenna is properly positioned in the mounting bracket as pictured below. To mount antenna to a pole: Attach the antenna to pole bracket as pictured. Use U-Bolt to secure bracket to pole and fasten. If you place the External Antenna outdoors, create a drip loop with the coaxial cable at the point where the cable enters the home through an outside wall. This can be done by twisting and securing the cable into a loop (no less than 4” across) near the entry point. This will help prevent moisture from gathering at entry point and leaking into the home. Consult a professional installer if you need more information. Exterior Wall To mount antenna to a flat surface: Secure bracket to desired surface using provided screws. Use of the Saddle and U-Bolt are not necessary for this option. Coax Cable Power Requirements The Base Unit can be plugged into a standard 2 or 3 prong 110 VAC receptacle using the Included power supply. The power supply consumes less than 10W (less than 0.2A). Additional Cable Requirements If the distance between the External Antenna and the Base Unit exceeds 50 feet, extension cables are available on our website. The included cable is RG-6. For better performance, you may replace it with RG-11. The total cable length should not exceed 65 feet unless you also purchase an upgraded External Antenna (see page v). A longer cable is helpful only if it allows you to place the External Antenna in a location where you measure stronger signal. Warning The zBoost ZB560P REACH base unit MUST only be used with the provided power adaptor. Use of other power adaptors will void the warranty and may damage the unit. Use of other equipment is not FCC approved. zBoost® REACH ZB560P Manual zBoost® REACH ZB560P Manual Setting Up Your zBoost Signal Booster Base Unit and the External Antenna. Generally, increasing this distance (up to 40 feet) will increase the performance and decreasing the distance will limit zBoost performance. Indoor Antenna FIRST: Mount the External Antenna Choosing the best location for the External Antenna provides the best performance and the largest area of improved signal. Choose a location for the External Antenna using your cell phone to determine the area of strongest signal - typically found outside, above the roofline or in an attic. The antenna must also remain at least 3 feet from any metal objects such as pipes, metal siding, A/C unit etc. and at lease 15 vertical feet above the Indoor Antenna. zBoost Base Unit THIRD: Run the Coaxial Cable 15 ft. of Vertical Separation Identify the best location for attachment of the mounting bracket Best Performance (Recommended) – such as an attic cross or main beam. Secure the mounting bracket at the highest possible point. Position the mounting bracket such that the External Antenna will be vertical and attach the External Antenna. See “Antenna Bracket Assembly” below for more information. NOTE: Refrain from securing cable or drilling holes until the system has been tested. Coaxial Cable Power Supply Connect the supplied 50 feet of RG-6 coaxial cable to the base of the External Antenna. Run the coaxial cable along a descending pipe or through a wall that leads closest to the location of the Base Unit. Should you need additional cable length, 15 foot extensions (Part #: Wall Mounting Y YX030-15w) are available at www.zBoost.com. Bracket Please note: Cable longer than 65 feet is not recommended. Antenna Bracket Assembly FOURTH: Connect zBoost Base Unit to Power IMPORTANT: Incorrectly mounting the External Antenna to the mounting bracket will impede performance. Ensure that the External Antenna is properly positioned in the mounting bracket as pictured below. Connect the zBoost Base Unit to the power supply and plug into a power outlet. When your zBoost system is in place and fully connected, walk throughout your home and verify that you are able to reliably place calls. If the signal strength has improved, your zBoost is working. To mount External Antenna to a pole: Attach the antenna to pole bracket as pictured. Use U-Bolt to secure bracket to pole and fasten. DO NOT mount to a metal pole. To mount External Antenna to a flat surface: Secure bracket to desired surface using provided screws. Use of the Saddle and U-Bolt are not necessary for this option. Upon initial power up, the LED will cycle RED, GREEN and ORANGE for 30 seconds. After 30 seconds, a series of GREEN flashes will indicate the quality of your setup. Following this, a solid GREEN light indicates normal conditions. If it is not solid GREEN, follow the instructions in the Base Unit LED Indicators section. Adjustments may be needed to optimize performance. If you find the increased signal coverage is acceptable, however, no additional adjustments are needed. See “zBoost Base Unit Light Indicators” on page 10) for more information. SECOND: Place the zBoost Base Unit where you want to create a Cell ZoneTM Connect the Indoor Antenna to the Base Unit and place it where you need signal. For the widest possible signal area, position the Base Unit near the middle of a room. You may also mount it on an interior wall by first removing the bracket, screwing the bracket to a wall (screws not included), then snapping the Base Unit back in place keeping the Indoor Antenna vertical. The Base Unit uses an omni-directional Indoor Antenna that delivers signal in a circular pattern around the antenna. The zBoost REACH requires at least 15 feet of vertical separation between the Base Unit and the External Antenna. Generally, increasing this distance (up to 40 feet) will increase the performance and decreasing the distance will limit the performance. Keep the Base Unit off the floor and at least 2 feet away from other cords, metal objects or other wireless devices such as wireless routers or wireless access points. The zBoost REACH performs best when there are no obstructions between the zBoost Base Unit and your mobile device. NOTE: The zBoost ZB560P REACH requires at least 15 feet of vertical separation between the zBoost® REACH ZB560P Manual zBoost® REACH ZB560P Manual Confirm That Your zBoost is Working Properly Improving Your Coverage Area When your zBoost system is in place and fully connected, you should walk throughout the area and see that you are able to reliably place calls. Remember, coverage varies based on outdoor signal level, home construction, and antenna placement. Coverage in adjoining rooms (next to, above, or below) will be reduced due to walls or ceiling/floors. Should you desire to improve coverage, you may: • Relocate the External Antenna in order to capture a better signal –higher is usually better and outside is better than inside. • Increase the distance between the Base Unit and the External Antenna. • Purchase an upgrade antenna available at www.zBoost.com. External Antenna Cell Tower Note Cell phone signal bars are approximate and vary from phone to phone. The number of bars can fluctuate widely, depending on the location of the phone, the position or angle of the phone, weather, etc. Most cell phone signal meters update every 6 to 10 seconds. An increase of only one bar typically indicates a 4x to 10x signal increase. Coax Cable Indoor Antenna THE BEST INDICATOR OF PRODUCT PERFORMANCE IS THE ABILITY TO RELIABLY PLACE AND RECEIVE CALLS WHERE YOU COULD NOT BEFORE SETTING UP THE ZB560P REACH. Base Unit Power Supply zBoost® REACH ZB560P Manual zBoost® REACH ZB560P Manual zBoost Base Unit Light Indicators Technical Specifications After Initial Power Up Light Mode Status zBoost is ready. PCS band Frequency 1. Unplug the BASE UNIT power supply. 2. Relocate the EXTERNAL ANTENNA to pick up the strongest signal from your wireless carrier. 3. 73 dB PCS band supported A, D, B, E, F, C Networks CDMA, GSM, GPRS, EDGE, EVDO, 1xRTT, UMTS, HSPA, 3G Output power UL: 19 dBm; DL: 4 dBm Cellular band 5. Wait 30 secs. for the BASE UNIT to power cycle on. Frequency Uplink: 824 to 849 MHz Downlink: 869 to 894 MHz System Gain 66 dB CEL band supported A, B, A’, B’ Networks CDMA, GSM, GPRS, EDGE, EVDO, 1xRTT, UMTS, HSPA, 3G Output power UL: 21 dBm; DL: 4 dBm Solution N/A Unplug the BASE UNIT power supply. 2. Move the EXTERNAL ANTENNA as far away from the INDOOR ANTENNA as possible, with at least 15 ft. of vertical separation (height difference). 3. Plug the BASE UNIT power supply back in. 4. 1. Wait 30 secs. for the BASE UNIT to power cycle on. Unplug the BASE UNIT power supply. Relocate the EXTERNAL ANTENNA to another spot. If you have a directional antenna re-aim it to reduce carrier signal strength. Plug the BASE UNIT power supply back in. 5. Wait 30 secs. for the BASE UNIT to power cycle on. ^ Refer to Solution #2 General Solution #2 1. 4. Excessive electronic noise in the system – the BASE UNIT will not operate. System Gain Plug the BASE UNIT power supply back in. zBoost is in use. N/A EXTERNAL ANTENNA and INDOOR ANTENNA are too close together. Uplink: 1850 to 1910 MHz Downlink: 1930 to 1990 MHz 4. SOLID RED Signal from the carrier’s cell 2. tower is too strong for the 3. BASE UNIT to operate properly. Flashing RED Move the EXTERNAL ANTENNA as far away from the INDOOR ANTENNA as possible, with at least 15 ft. of vertical separation (height difference). Solution #3 SOLID GREEN Flashing GREEN SOLID ORANGE Product Specifications for zBoost REACH ZB560P Solution N/A Solution #1 During Initial Power Up Light Mode Status Cycle RED, System is GREEN, powering up. ORANGE Please allow up to 30 seconds. Flashing BASE UNIT will GREEN flash GREEN once for every 2 dB less than optimal system gain. Three flashes or less indicates the system will still operate properly. Power Consumption 3W standby; 7W max signal - 5.0VDC, 2.0A Max Wall Supply Input ; Voltage 100-240VAC, 50-60 Hz Input and Output Impedance TNC Connector: 50 Ohm; F Connector:75 Ohm System Certifications FCC Parts 15 & 20, Industry Canada Base Unit Size and Weight 5” x 7” x 1.25” – 9 oz. Operating Conditions Indoor Use Only (40° - 105° F) Coverage area 3,500 sq. ft. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device. This product is covered by patent US 7,706,744. Other U.S. and foreign patents pending. 10 11 zBoost® REACH ZB560P Manual zBoost® REACH ZB560P Manual Frequently Asked Questions Warranty Information Limited 2 Year Warranty What can I expect my cell phone signal range and strength to be inside my home? The closer you are to the base, the stronger the signal. This will vary with different conditions. Some of the conditions that will affect the improved coverage area are signal strength outdoors, the type of building materials in the home, the placement of the unit and the antenna’s proximity to cellular towers. You can expect that your indoor coverage will be improved. You will be able to make calls where you couldn’t before. The degree of improvement will depend upon many factors. The intent of zBoost products are to bring outside coverage inside. Just as the signal bars move up and down when outside, the boosted signal will fluctuate in a similar fashion. Is a cellular phone signal booster the same as a wireless router; will it help my WiFi signal? The zBoost unit will not help your WiFi service. This unit is designed to work with wireless PCS and Cellular phones and devices. The WIFI in your home operates on a different frequency. Why isn’t my cell phone indicating more signal with more bars? You may not always observe more bars that gain on your signal meter because of the signal spreading out from the antenna. If your phone has a dB meter, 3 dB is a significant increase of 2x, 6 dB is 4x, and 10 dB is 10x. On a four bar phone, one "bar" equals about 10 dB. The increase in signal you will see depends upon: Register your product at www.zBoost.com zBoost warrants every zBoost product to be free from defects in material and workmanship under normal use for the warranty period of two years. Who Is Covered? You must have proof of purchase to receive warranty service. A sales receipt or other documentation showing the product purchased and the purchase date is considered proof of purchase. This limited warranty extends only to the original consumer purchaser or any person receiving the product as a gift from the original consumer purchaser and to no other purchaser or transferee. What is Covered? Warranty coverage begins the day you purchase the product. For one year from the original date, the zBoost Cell Phone Signal Booster will be repaired or replaced with a new, repaired, refurbished or comparable product (whichever is deemed necessary by zBoost ) if it becomes defective or inoperative. The exchange will be made without charge to you for parts and labor. You will be responsible for the cost of shipping to the location designated by zBoost. All products, including replacement products, are covered only for the original warranty period. When the warranty on the original product expires, the warranty on the replacement product also expires. • The level of signal at the External Antenna (outdoor) • The care of the antenna placement (two feet away from metal, adequate antenna separation [15 feet recommended]) What is Excluded? • The signal already present inside (related to building losses) Your warranty does NOT cover: • The distance of your phone/device from the Base Unit (signal spreads or diminishes rapidly with distance.) There are usually several cell phones in use at one time in my home, will your product boost all of our signals simultaneously? The zBoost ZB560P REACH is designed to cover multiple signals simultaneously and will allow multiple users to operate at the same time. • Labor charges for set up of the unit. • Product replacement because of misuse, accident, lightning damage, unauthorized repair or other cause not within the control of zBoost. • Incidental or consequential damages resulting from the product. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. • Any modifications or other changes to the product, including but not limited to software or hardware modifications in any way other than as expressly authorized by zBoost will void this limited warranty. • Product that has been modified or adapted to enable it to operate in any country other than the country for which it was designed, manufactured, approved and/or authorized, or repair of products damaged by these modifications. Does the zBoost work if you have no bars? No, if no signal is present outdoors zBoost products will not work for you. Also, keep in mind if your best signal is 1 bar at the External Antenna, your coverage will be limited to a small room. You could improve that with an upgraded antenna. (See page v 12 13 zBoost® REACH ZB560P Manual Make sure you keep… Please keep your sales receipt or other document showing proof of purchase. Attach it to this User Manual and keep both nearby. Also, keep the original box and packing material in case you need to return your product. Before requesting repair service… If red light is on, system is receiving signals from either the mobile device or the base station transceiver which are too strong for proper operation. Please unplug your system. Re-orient your External Antenna and/or Base Unit to reduce the excessive signal source. Plug your system back in. If still solid red, call customer support 1-800-871-1612. To get warranty service… Warranty service will be provided by zBoost. If you believe you need service for your unit, contact zBoost at 1-800-871-1612 or support@zboost.com. A representative will go through a diagnostic checklist with you. If it is determined that the product needs to be returned for service or exchanged, you will receive a return merchandise authorization (RMA) number. The representative will give you complete shipping details. Do not return products to zBoost without a Return Authorization Number (RMA). To get out of warranty service… To obtain out of warranty service, contact zBoost at 1-800-871-1612 or support@zboost.com for information on the possibility of any costs for repair or replacement of out-of-warranty products. Reminder Record the model and serial number found on the product below: Model #: __________________________________ Serial #: __________________________________ Purchase Date: ____________________________ 14
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : bmangold Title : ZB560P_Manual.indd Create Date : 2014:03:19 13:04:33-04:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2014:03:19 13:04:33-04:00 Producer : Acrobat Distiller 10.0.0 (Windows) Document ID : uuid:b0c13775-aa74-480e-9228-cd644d126f01 Instance ID : uuid:00e86ccc-cf02-4e20-b1d4-7e6cda4b6ad6 Page Count : 11 Author : bmangoldEXIF Metadata provided by EXIF.tools