zBoost ZB570-TRI-ALTE Model ZB570-A Signal Booster User Manual ZB575X Manual indd

Download:
Mirror Download [FCC.gov]
Document ID	2228493
Application ID	s75r5Y0KDR3MSzYnNCZQWg==
Document Description	ZB575X_Manual_Rev1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	152.51kB (1906417 bits)
Date Submitted	2014-03-28 00:00:00
Date Available	2014-03-28 00:00:00
Creation Date	2014-03-19 13:52:44
Producing Software	Acrobat Distiller 10.0.0 (Windows)
Document Lastmod	2014-03-19 13:52:44
Document Title	ZB575X-Manual.indd
Document Creator	PScript5.dll Version 5.2.2
Document Author:	bmangold

zBoost® TRIO Xtreme
ZB575X Manual
Models:
• ZB575X-A
• ZB575X-V
zBoost® products have a 30-day money back guarantee when purchased directly from
zBoost. If product is purchased from a reseller or third party, the purchaser is subject to the
policies of the third party.
One year manufacturer warranty. Warranty registration at www.zBoost.com
v.0214
zBoost® TRIO Xtreme ZB575X Manual
zBoost® TRIO Xtreme ZB575X Manual
FCC Requirements
This is a CONSUMER Device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your
provider’s consent. Most wireless providers consent to the use of signal boosters. AT&T, Sprint,
T-Mobile, Verizon and 90 additional carriers have already given consent for all consumers to use this
device. Some providers may not consent to the use of this device on their network. If you are unsure,
contact your provider.
About zBoost®
zBoost, the leader in cell phone signal boosters, manufactures an award-winning line of cell
phone signal boosters that enhance the performance of your cell phone, smartphone and
wireless data card.
Uses patented technologies and protects the carrier networks.
1-year manufacturer warranty – register your product at www.zBoost.com.
You MUST operate this device with approved antennas and cables as specified by the manufacturer.
Antennas MUST be installed at least 20 cm (8 inches) from any person.
You MUST cease operating this device immediately if requested by the FCC or a licensed wireless
service provider.
WARNING. E911 location information may not be provided or may be inaccurate for calls served by
using this device.
FCC contact information: www.fcc.gov/signal-boosters/registration
Industry Canada Regulations
IC ID: 5544A-ZB570TRIVLT, 5544A-ZB570TRIALT
This Class B digital apparatus meets all requirements of the Canadian Interference Causing
Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Warning
The term “IC:” before the radio certification number only signifies that Industry Canada technical
specifications were met.
Any product modifications that use unauthorized
antennas, cables, and/or coupling devices is no longer
FCC compliant and will void the product warranty.
RF Exposure: The manufacturer’s rated output power of this equipment is for single carrier
operation. For situations when multiple carrier signals are present, the rating would have to be
reduced by 3.5 dB, especially where the output is re-radiated and can cause interference to
adjacent band users. This power reduction is to be by means of input power or gain reduction and
not by an attenuator at the output of the device.
FCC Information
FCC ID: SO4ZB570-TRI-VLTE, SO4ZB570-TRI-ALTE
Warning: Changes or modifications to this device not expressly approved by zBoost® could void
the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If the equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected
•
Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. In accordance with FCC requirements of human exposure to radiofrequency
fields, the radiating element (antenna) shall be installed such that a minimum separation distance
of 20cm (8in) is maintained from all persons. Additionally, the device must not be used above 10 m
above ground.
Cet appareillage numérique de la classe [B] répond à toutes les exigences de l’interférence
canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions
suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter
n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
Le fabricant nominale de la puissance de sortie de ce matériel est simple transporteur. Pour les
situations lorsque plusieurs signauxporteurs sont présents, l’évaluation devrait être réduite de
3.5 dB, en particulier lorsque le signal de sortie est ré-émise et peut provoquer des interférences
adjacentes à la bande utilisateurs. Ce pouvoir est de la réduction par le biais de la sortie
d’alimentation ou la réduction de gain et non par un atténuateur à la sortie du dispositif.
Please note: This unit has been approved for use in Canada under RSS 131, however, consent
for the use of this device to improve cellular or PCS coverage, must be obtained through your
cellular or PCS provider, prior to placing the unit in operation. Please refer to the Industry Canada
document CPC 2-1-05, Section 6.1 available or viewable at:
http://www.ic.gc.ca/epic/site/smt-gst.nsf/en/sf08942e.html
Copyright Notice
This manual is copyrighted. All rights reserved. This manual, whole or in part, may not be copied,
photocopied, reproduced, translated or reduced to any electronic medium or machine readable
form for distribution. This manual whole or in part, may not be modified without prior consent, in
writing, from zBoost.
Copyright © 2014 by zBoost.
Trademarks
Wireless Extenders, Wi-Ex, the Wi-Ex logo, zBoost, the zBoost logo and Extending Cell Zones are
registered trademarks of zBoost.
ii
zBoost® TRIO Xtreme ZB575X Manual
zBoost® TRIO Xtreme ZB575X Manual
Safety and Product Warranty Information
Package Contents
Before you begin, make sure all of the following parts came with your zBoost TRIO Xtreme:
Safety Guidelines
In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating
element (antenna) shall be positioned such that a minimum separation distance of 8 inches (20cm)
is maintained between the radiating element and the user and/or general population.
Literature Contents:
①
① Setup overview for zBoost TRIO Xtreme
SETUP OVERVIEW
Limited Liability
In no event shall zBoost be liable for any direct, indirect, special, punitive, incidental, exemplary
or consequential damages, or any damages, whether in an action under contract, negligence,
or any other theory, arising out of or in connection with the set up of, use of, inability to use, or
performance of the information, services, products, and materials available from this manual.
These limitations shall apply notwithstanding any failure of essential purpose of any limited
remedy. Because some jurisdictions do not allow limitations on how long an implied warranty
last, or the exclusion or limitation of liability for consequential or incidental damages, the above
limitations may not apply to you.
For full warranty guidelines, see page 14.
Product Contents:
② zBoost Base Unit
②
③ Indoor Antenna
③
④ Power Supply
⑤ RG-6 Coax Cable (35 ft.)
④
⑥ RG-6 Coax Cable (15 ft.)
⑦ Window Entry Cable
⑧ External Antenna
⑤
⑨ External Antenna Mounting Hardware
⑥
⑦
⑧
⑨
iii
iv
zBoost® TRIO Xtreme ZB575X Manual
zBoost® TRIO Xtreme ZB575X Manual
Optional Accessories
Table of Contents
The following accessories are authorized for this zBoost product. Please see our website for a
complete selection. To order, call 1-800-871-1612, or visit www.zBoost.com.
FCC Requirements........................................................................................................................i
FCC Information ............................................................................................................................i
Broadcast Antennas - Indoor
CANT-0039
Indoor Broadcast Antenna, Omni Whip Direct to Booster, Black, Wideband, LTECEL-AWS-PCS (1 dBi)
CANT-0045*
Indoor Broadcast Antenna, Wideband Directional Panel, LTE-CEL-AWS-PCS
(8 / 7.5 dBi)
YX052
Indoor Broadcast Antenna, Wideband Omnidirectional Ceiling Mount, LTE-CELAWS-PCS (1 / 2 dBi)
External Antennas - Outdoor
Industry Canada Regulations .......................................................................................................ii
Copyright Notice ..........................................................................................................................ii
Trademarks ..................................................................................................................................ii
Safety Guidelines ........................................................................................................................ iii
Limited Liability ........................................................................................................................... iii
Safety and Product Warranty Information................................................................................... iii
Package Contents ........................................................................................................................ iv
CANT-0040
Outdoor External Antenna, Wideband Omni Directional, LTE-CEL-AWS-PCS
(3 / 5 dBi)
Optional Accessories .................................................................................................................... v
CANT-0042
Outdoor External Antenna, Wideband Directional Log Periodic, LTE-CEL-AWS-PCS
(10 / 12 dBi)
Overview ........................................................................................................................................ 2
CANT-0043
Window-Mount External Antenna, Wideband Directional Panel, LTE-CEL-AWS-PCS
(6 / 7 dBi)
Table of Contents .......................................................................................................................... 1
Why Indoor Signals Can Be Weak ............................................................................................... 2
Preparing to Set Up Your zBoost Product.................................................................................... 3
Coax Cable - To be used in addition to the cable included in your kit
Tools Needed .............................................................................................................................. 3
YX030-0W8
8 Inch Window Entry Cable with F-Female Connectors
Check for Signal Strength ........................................................................................................... 3
YX030-15W
15 Foot RG-6 Coaxial Extension Cable with F-Male Connectors
IMPORTANT: Before Installing, Note These Important Factors in Determining Performance ....... 4
YX030-35W
35 Foot RG-6 Coaxial Extension Cable with F-Male Connectors
Additional Cable Requirements ................................................................................................... 4
YX030-50W
50 Foot RG-6 Coaxial Cable with F-Male Connectors
Grounding the External Antenna.................................................................................................. 5
YX031-100W
100 Foot Low Loss RG-11 Coaxial Cable with F-Male Connectors
Securing Cable with a Drip Loop ................................................................................................. 5
Accessories
YX012
Power Requirements ................................................................................................................... 5
Outdoor External Antenna Grounding Kit
Setting Up Your zBoost Signal Booster ....................................................................................... 6
FIRST: Mount the External Antenna............................................................................................. 6
SECOND: Position the Base Unit ................................................................................................ 6
THIRD: Connect the coax cables via the provided window entry cable ........................................ 7
FOURTH: Connect the zBoost Base Unit to Power...................................................................... 7
FIFTH: Antenna Aiming ............................................................................................................... 7
Confirm That Your zBoost is Working Properly ............................................................................ 8
Improving Your Coverage Area ..................................................................................................... 9
zBoost Base Unit Light Indicators .............................................................................................. 10
Technical Specifications ..............................................................................................................11
Frequently Asked Questions ...................................................................................................... 12
Warranty Information .................................................................................................................. 13
* The FCC requires that this panel antenna has a minimum horizontal separation of 6 feet (2 meters)
from other CMRS (commercial mobile radio service) devices.
zBoost® TRIO Xtreme ZB575X Manual
zBoost® TRIO Xtreme ZB575X Manual
Preparing to Set Up Your zBoost Product
Overview
Thank you for choosing zBoost! You will now be able to use your cell phone INSIDE your home.
Gone are the days when you had to go to the window upstairs or walk outside to use your cell
phone. Like a skylight that brings sunlight into your home, zBoost TRIO transports and amplifies the
outdoor 2G/3G and 4G data signal into your home.
Tools Needed
The following tools are needed to set up your booster:
•
#2 Phillips screwdriver
Why Indoor Signals Can Be Weak
•
Cellular phone operating in the band supported by your zBoost unit
There are several obstacles that can contribute to the poor reception you receive in your home:
•
Drill (may be required for outdoor or attic antenna placement)
1.
Location of the Cell Phone Tower in Relation to Your Home
While cell phone providers have tried to place cell phone towers to provide the best overall
coverage, local ordinances and terrain features can impose restrictions on where these
towers can be placed, thus, limiting the signal strength available at your location.
2.
Obstructions Caused by Buildings, Terrain and Trees
Cell phone signals can be completely blocked or reflected by buildings, walls, trees, hills
and other terrain features resulting in low signal strength.
3.
Energy Efficient Windows
Energy efficient windows contain a metal film that can affect signal penetration into the
house.
Check for Signal Strength
Before placing the unit in your home, make sure that you have reliable signal and fast/reliable data
speeds outside your home, in the attic, at roof level or wherever you plan to place the External
Antenna. zBoost can only bring signal into your home when it reaches the External Antenna. If
there is no signal, zBoost will not work for you.
If a weak signal is available at ground level, check the signal strength in your attic or at roof level
location where the signal will likely be stronger and where the External Antenna can be placed for
best performance.
If you have reliable, fast data speeds outside your home, then zBoost can bring the signal into your
home.
If only one signal bar is displayed on your cell phone outside, indoor coverage will be
limited to one small room. We recommend placing the External Antenna outside and/or
purchasing a zBoost upgrade External Antenna for increased coverage (see page v).
Note
Cell phone signal bars are approximate and vary from
phone to phone. The number of bars can fluctuate
widely, depending on the location of the phone, the
position or angle of the phone, weather, etc. Most cell
phone signal meters update every 6 to 10 seconds. An
increase of only one bar typically indicates a 4x to 10x
signal increase.
zBoost® TRIO Xtreme ZB575X Manual
IMPORTANT: Before Installing, Note These Important Factors in Determining
Performance
1.
At least 15 vertical feet is needed between the External Antenna (receives the outside signal)
and the Indoor Antenna (rebroadcasts the signal indoors). Separation less than 15 vertical feet
will result in decreased performance.
If the antennas are too close together, a solid ORANGE light will appear on the Base Unit see the Base Unit Light Indicators section (page 11). To capture the best signal, place the
External Antenna as high as possible.
2.
Position the External Antenna vertically and keep it at least 3 feet above any metal.
15 ft. of vertical
separation
zBoost® TRIO Xtreme ZB575X Manual
Grounding the External Antenna
If the External Antenna is placed outdoors, it must be properly grounded. (See page v for a
recommended grounding kit).
The setup must be in accordance with Article 810 of the National Electric Code (NEC). A listed
antenna discharge unit must be provided for the lead-in coaxial cable per NEC article 8.10.20 or the
shield of the coaxial cable must be permanently and effectively grounded in accordance with NEC
article 8.10.21. Please consult a professional installer or electrician for more information.
Securing Cable with a Drip Loop
Exterior Wall
If the External Antenna is placed outdoors,
create a drip loop with the coaxial cable at
the point where the cable enters the home
through an outside wall. This can be done by
twisting and securing the cable into a loop (no
less than 4” across) near the entry point. This
will help prevent moisture from gathering at
entry point and leaking into the home. Consult
a professional installer for more information.
Coax Cable
Power Requirements
The Base Unit can be plugged into a standard 2 or 3 prong 110 VAC receptacle using the included
power supply. The power supply consumes less than 10W (less than 0.2A).For more information on
power consumption, see “Technical Specifications” on page 12.
Additional Cable Requirements
Warning
If the distance between the External Antenna and the Base Unit exceeds 50 feet, extension cables
are available on our website. The included cable is RG-6.
The total cable length should not exceed 65 feet unless upgraded cable and/or upgraded External
Antenna (see page v) is used. A longer cable is helpful only if it allows you to place the External
Antenna in a location where you measure stronger signal.
Cable
Recommended Length
RG-6
Up to 65 feet
RG-11
Up to 120 feet
The zBoost TRIO Xtreme base unit MUST only be used
with the provided power adaptor. Use of other power
adaptors will void the warranty and may damage the
unit. Use of other equipment is not FCC approved.
zBoost® TRIO Xtreme ZB575X Manual
zBoost® TRIO Xtreme ZB575X Manual
Setting Up Your zBoost Signal Booster
Indoor Antenna
FIRST: Mount the External Antenna
Choosing the best location for the External Antenna provides the best performance and the largest
area of improved signal. Choose a location for the External Antenna using your cell phone to
determine the area of strongest signal - typically found outside, above the roofline or in an attic.
Keep in mind that if your best signal is one bar, your coverage will be limited to one small room.
zBoost Base Unit
Coaxial Cable
Maximum performance will be achieved when the antenna is aimed at the strongest signal from
your wireless provider. If you know the direction of your provider’s tower, simply point the antenna
in that direction. If you are unsure of the location of the nearest tower, loosely secure the antenna
to the mounting surface or mast (not provided) to allow adjustment or rotation around mast. Before
securing antenna hardware, take care in finding the optimum angle at which to aim the antenna –
See Antenna Aiming section on page 9 for further instruction.
Once you have determined the optimum location and
angle, connect the L-bracket to the antenna and secure the
antenna bracket to a mast (not provided) or a flat surface
using the provided antenna hardware.(see bracket assembly
illustration). Ensure that the antenna remains at least 3 feet
above any metal objects (such as pipes, metal siding, A/C
unit etc.) and parallel to the ground with the two holes on the
side of the antenna are facing down.
► To mount antenna to a pole: Attach bracket end
of antenna to pole bracket as pictured. Use U-Bolt to
secure bracket to pole and fasten.
► To mount antenna to a flat surface: Attach bracket
end of antenna desired surface. Secure bracket using
provided screws. The of the U-Bolt is not necessary for
this option.
Base Unit Bracket
Power Supply
zBoost Base Unit Assembly
no obstructions between the zBoost Base Unit and your mobile device.
Note: The Base Unit can be easily mounted on a wall by first removing the Silver bracket from the
Base Unit (see “zBoost Base Unit Assembly” above) and using 2 mounting screws to affix to wall keeping the antenna vertical.
Remember, the zBoost TRIO requires at least 15 feet of vertical separation between the Base
Unit and the External Antenna. Generally, increasing this distance (up to 40 feet) will increase the
performance and decreasing the distance will limit zBoost performance.
THIRD: Connect the coax cables via the provided window entry cable
NOTE: Refrain from securing cable or drilling holes until the system has been tested.
The zBoost ZB575X includes 2 coax cables (35 ft. and 15 ft.) and a window-entry cable for
connecting the External Antenna to the Base Unit. If you do not plan to run the cable through a
window, the window entry cable is not needed.
Note
Avoid placing the External Antenna near metal such as
wiring, A/C ducts, metal siding, truss plates, etc.
When connecting the cable to the antenna, run the
cable straight down from the antenna. Avoid draping
the coax near the antenna.
To run the coax cable through a window: Connect the two provided RG-6 cables (35 feet & 15
feet) using the provided window-entry cable. Use the attached cables to connect the Base Unit and
External Antenna through a window, positioning the window-entry cable at the window closing (See
Option 1 on page 8).
To run the coax cable through a wall: Connect the two provided RG-6 cables. Then connect one
end of the cable to the base of the External Antenna. Run the coaxial cable along a descending
pipe or through a wall that leads closest to the location of the Base Unit. Connect the remaining end
of the cable to the Base Unit (See Option 2 on page 8).
Should you need additional cable length, 15 foot extensions (Part #: YX030-15w) are available at
www.zBoost.com. Please note: Cable longer than 65 feet is not recommended.
SECOND: Position the Base Unit
Assemble the Base Unit and Indoor Antenna and position the antenna vertically. This Base Unit
uses an omni-directional antenna that delivers signal in a circular pattern around the antenna. Place
the Base Unit in desired location – where you want to create a Cell Zone™ For the widest possible
signal area, it is recommended that you position the Base Unit near the middle of a room. The Base
Unit can be placed on a flat surface (e.g., a bookshelf, desk, end table, etc.) and performs best
when located at least 4 feet above the floor or approximately the height of a cell phone when it is
typically in use (avoid placing the Base Unit on the floor).
FOURTH: Connect the zBoost Base Unit to Power
Connect the zBoost Base Unit to the power supply and plug into a power outlet.
Keep the Base Unit at least 2 feet away from other cords, metal objects or other wireless devices
such as wireless routers or wireless access points. The zBoost TRIO performs best when there are
Upon initial power up, the LED will cycle RED, GREEN and ORANGE for 30 seconds. After 30
seconds, a series of GREEN flashes will indicate the quality of your setup. Following this, a solid
GREEN light indicates normal conditions. If it is not solid GREEN, follow the instructions in the
Base Unit LED Indicators section. Adjustments may be needed to optimize performance. If you find
the increased signal coverage is acceptable, however, no additional adjustments are needed. See
“zBoost Base Unit Light Indicators” on page 11 for more information.
zBoost® TRIO Xtreme ZB575X Manual
zBoost® TRIO Xtreme ZB575X Manual
FIFTH: Antenna Aiming
External Antenna
Cell Tower
To get the maximum benefit, you will want to take special care to make sure you point the antenna
in the direction of the best signal for your wireless service provider. You may wish to use a YX699
RF signal meter to help during this process or try our zBoost Signal Finder Android App. The
majority of the time a cell tower will hold more than 1 frequency band and/or service provider.
To aim the antenna for maximum signal, you will need a phone operating on the same wireless
network(s) in use at the install location.
Window
Entryy Cable
Note: A 1 dBm increase is 25% gain in signal strength.
15 ft of vertical
separation
Coaxial Cable
If you do not know which direction the best signal is coming from, once the unit is installed, rotate
the External Antenna in 90 degree increments while measuring the results inside the desired
coverage area.
Indoor
Antenna
1.
Place the cell phone(s) on a non-metal surface about 6-8 feet from the Base Unit.
2.
Turn the signal booster on and wait 30 seconds. Note the number of signal bars displayed
on your cell phone. For best results, you want to place your phone where the phone’s signal
meter displays in the middle of the signal meter range or less so that it can indicate as you
rotate the External Antenna to the optimum direction. If it is reading too high, move the phone
farther from the Indoor Antenna. (Note: if you’re using signal bars to measure signal strength,
turn off your LTE during this process)
3.
Record the number of signal bars or dBm________(A) on your cell phone. You can use our
YX699 RF Signal Meter or an application on a smart phone to get the dBm. Leave the phone
in exactly the same place and pointing in the same direction for the following steps. Note the
direction External Antenna starting position ________________.
4.
Rotate the External Antenna 90 degrees and then record the phone signal bars ______(B).
5.
Continue to rotate the antenna another 90 degrees in the same direction and record the phone
signal bars _________(C).
6.
Again, rotate the antenna another 90 degrees in the same direction and again record the
phone signal bars _________(D).
7.
If you desire to optimize further, then look for the two highest signal bar readings above and
move the antenna between these two points to find the highest signal bars reading.
8.
Look for the highest reading above. Set the antenna to that position and tighten the antenna to
the mast of your choosing. We suggest PVC pipe that is at least 1.5” or J-Pole (part # YX014,
not included).
Power Supply
zBoost Base Unit
Coaxial Cable
Option 1: Running cable through a window
External Antenna
Cell Tower
15 ft of vertical
separation
Coaxial Cable
Confirm That Your zBoost is Working Properly
When your zBoost system is in place and fully connected, walk throughout your home and verify
that you have fast, reliable data speeds. If the signal strength has improved, your zBoost is working.
Remember, coverage varies based on outdoor signal level, home construction, and antenna
placement. Coverage in adjoining rooms will be reduced by walls and building materials.
Indoor
Antenna
Power Supply
Coaxial Cable
zBoost Base Unit
Option 2: Running cable through a wall
zBoost® TRIO Xtreme ZB575X Manual
zBoost® TRIO Xtreme ZB575X Manual
Improving Your Coverage Area
zBoost Base Unit Light Indicators
Should you desire to improve coverage, you may:
•
Purchase an upgrade antenna available at www.zBoost.com
NOTE: The zBoost ZB575X requires at least 15 feet of vertical separation between the Base
Unit and the External Antenna. Generally, increasing this distance (up to 40 feet) will increase the
performance and decreasing the distance will limit zBoost performance.
During Initial Power Up
Light Mode Status
Cycle RED, System is
GREEN,
powering up.
ORANGE
Please allow up
to 30 seconds.
Flashing
BASE UNIT will
GREEN
flash GREEN
once for every
2 dB less than
optimal system
gain. Three
flashes or less
indicates the
system will still
operate properly.
After Initial Power Up
Light Mode Status
SOLID
GREEN
Flashing
GREEN
SOLID
ORANGE
Note
Cell phone signal bars are approximate and vary from
phone to phone. The number of bars can fluctuate
widely, depending on the location of the phone, the
position or angle of the phone, weather, etc. Most cell
phone signal meters update every 6 to 10 seconds. An
increase of only one bar typically indicates a 4x to 10x
signal increase.
zBoost is ready.
Solution
N/A
1.
Unplug the BASE UNIT power supply.
2.
Relocate the EXTERNAL ANTENNA to pick up the
strongest signal from your wireless carrier.
3.
Move the EXTERNAL ANTENNA as far away from the
INDOOR ANTENNA as possible, with at least 15 ft. of
vertical separation (height difference).
4.
Plug the BASE UNIT power supply back in.
5.
Wait 30 secs. for the BASE UNIT to power cycle on.
Solution
N/A
zBoost is in use. N/A
EXTERNAL
ANTENNA
and INDOOR
ANTENNA
are too close
together.
1.
Unplug the BASE UNIT power supply.
2.
Move the EXTERNAL ANTENNA as far away from the
INDOOR ANTENNA as possible, with at least 15 ft. of
vertical separation (height difference).
3.
Plug the BASE UNIT power supply back in.
4.
SOLID RED Signal from the 1.
carrier’s cell
2.
tower is too
strong for the
3.
BASE UNIT to
operate properly.
4.
Flashing
RED
10
Solution #1
Increase the distance between the Indoor Antenna and the External Antenna.
Excessive
electronic noise
in the system –
the BASE UNIT
will not operate.
Solution #2
Relocate the External Antenna in order to capture a better signal –higher is usually better.
•
Wait 30 secs. for the BASE UNIT to power cycle on.
Unplug the BASE UNIT power supply.
Relocate the EXTERNAL ANTENNA to another spot.
If you have a directional antenna re-aim it to reduce
carrier signal strength.
Plug the BASE UNIT power supply back in.
5. Wait 30 secs. for the BASE UNIT to power cycle on.
^ Refer to Solution #2
11
Solution #3
•
zBoost® TRIO Xtreme ZB575X Manual
zBoost® TRIO Xtreme ZB575X Manual
Technical Specifications
Frequently Asked Questions
Product Specifications for zBoost TRIO Xtreme ZB575X-V
Specs for VLTE Band
Specs for PCS Band
Specs for CEL Band
Frequency
Uplink: 776—787 MHz
Downlink: 746—757 MHz
Uplink: 1850—1910 MHz
Uplink: 824—849 MHz
Downlink: 1930—1990 MHz Downlink: 869—894 MHz
Band supported
13
A, D, B, E, F, C
A, B, A’, B’
System gain
68 dB
77 dB
69 dB
Output power
3 dBm
4 dBm
3 dBm
Networks
LTE (Verizon)
CDMA, GSM, GPRS, EDGE, EVDO, 1xRTT, UMTS,
HSPA, 3G
General Specifications
Power Consumption
3W standby; 7W max signal - 2.5A Max
Wall Supply Input ; Voltage
100-240VAC, 50-60 Hz; 5.0VDC
Input and Output Impedance
TNC Connector: 50 Ohm; F Connector: 75 Ohm
System Certifications
FCC Parts 15 & 20, Industry Canada
Base Unit Size and Weight
5” x 7” x 1.25” – 9 oz.
Operating Conditions
Indoor Use Only (40° - 105° F)
Coverage (open areas)
Up to 5,500 sq. ft.
What can I expect my cell phone signal range and strength to be inside my home?
The closer you are to the base, the stronger the signal. This will vary with different conditions. Some
of the conditions that will affect the improved data coverage area are signal strength outdoors, the
type of building materials in the home, the placement of the unit and the antenna’s proximity to
cellular towers.
You can expect that your indoor coverage will be improved. You will experience faster, more reliable
data where you didn’t before. The degree of improvement will depend upon many factors. The
intent of zBoost products are to bring outside coverage inside. Just as the signal bars move up and
down when outside, the boosted signal will fluctuate in a similar fashion.
Is a cellular phone signal booster the same as a wireless router; will it help my WiFi signal?
The zBoost unit will not help your WiFi service. The WiFi in your home operates on a different
frequency.
Why isn’t my cell phone indicating more signal with more bars?
You may not always observe more bars on your signal meter because of the signal spreading out
from the antenna. If your phone has a dB meter, 3 dB is a significant increase of 2x, 6 dB is 4x, and
10 dB is 10x. On a four bar phone, one "bar" equals about 10 dB.
The increase in signal you will see depends upon:
•
The level of signal at the External Antenna (outdoor)
Specs for ALTE Band
Specs for PCS Band
Specs for CEL Band
•
Uplink: 704—716 MHz
Downlink: 734—746 MHz
Uplink: 1850—1910 MHz
Downlink: 1930—1990 MHz
Uplink: 824—849 MHz
Downlink: 869—894 MHz
The care of the antenna placement (two feet away from metal, adequate antenna
separation [15 vertical feet of separation is recommended])
•
The signal already present inside (related to building losses)
Band supported 17
A, D, B, E, F, C
A, B, A’, B’
•
System gain
68 dB
77 dB
69 dB
The distance of your phone/device from the Base Unit (signal spreads or diminishes rapidly
with distance.)
Output power
3 dBm
4 dBm
3 dBm
LTE (AT&T)
CDMA, GSM, GPRS, EDGE, EVDO, 1xRTT, UMTS,
HSPA, 3G
Product Specifications for zBoost TRIO Xtreme ZB575X-A
Frequency
Networks
General Specifications
There are usually several mobile devices in use at one time in my home, will your product
boost all of our signals simultaneously?
The zBoost TRIO Xtreme is designed to cover multiple signals simultaneously and will allow
multiple users to operate at the same time.
Power Consumption
3W standby; 7W max signal - 2.5A Max
Wall Supply Input ; Voltage
100-240VAC, 50-60 Hz; 5.0VDC
Does the zBoost work if you have no bars?
Input and Output Impedance
TNC Connector: 50 Ohm; F Connector: 75 Ohm
System Certifications
FCC Parts 15 & 20, Industry Canada
No, if no signal is present outdoors zBoost products will not work for you. Also, keep in mind if your
best signal is 1 bar at the External Antenna, your coverage will be limited to a small room. You
could improve that with an upgraded antenna (See page v).
Base Unit Size and Weight
5” x 7” x 1.25” – 9 oz.
Operating Conditions
Indoor Use Only (40° - 105° F)
Coverage (open areas)
Up to 5,500 sq. ft.
The Manufacturer’s rated output power of this equipment is for single carrier operation. For
situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB,
especially where the output signal is re-radiated and can cause interference to adjacent band users.
This power reduction is to be by means of input power or gain reduction and not by an attenuator at
the output of the device.
This product is covered by patent US 7,706,744. Other U.S. and foreign patents pending.
12
13
zBoost® TRIO Xtreme ZB575X Manual
Warranty Information
Limited 1 Year Warranty
Warranty Registration at www.zBoost.com
zBoost® warrants every zBoost product to be free from defects in material and workmanship under
normal use for the warranty period of one year.
Who Is Covered?
You must have proof of purchase to receive warranty service. A sales receipt or other
documentation showing the product purchased and the purchase date is considered proof of
purchase. This limited warranty extends only to the original consumer purchaser or any person
receiving the product as a gift from the original consumer purchaser and to no other purchaser or
transferee.
What is Covered?
Warranty coverage begins the day you purchase the product. For one year from the original date,
the zBoost Cell Phone Signal Booster will be repaired or replaced with a new, repaired, refurbished
or comparable product (whichever is deemed necessary by zBoost) if it becomes defective or
inoperative. The exchange will be made without charge to you for parts and labor. You will be
responsible for the cost of shipping to the location designated by zBoost.
All products, including replacement products, are covered only for the original warranty period.
When the warranty on the original product expires, the warranty on the replacement product also
expires.
What is Excluded?
zBoost® TRIO Xtreme ZB575X Manual
Make sure you keep…
Please keep your sales receipt or other document showing proof of purchase. Also, keep the
original box and packing material in case you need to return your product.
Before requesting repair service…
Make sure you have at least 15 feet of vertical separation between External Antenna and Base Unit
and that the External Antenna is at least 3 feet above metal.
If red light is on, system is receiving signals from either the mobile device or the base station
transceiver which are too strong for proper operation. Please unplug your system. Re-orient your
Signal Antenna and/or Base Unit to reduce the excessive signal source. Plug your system back in.
If still solid red, call customer support 1-800-871-1612.
To get warranty service…
Warranty service will be provided by zBoost. If you believe you need service for your unit,
contact zBoost at 1-800-871-1612 or support@zBoost.com. A representative will go through a
diagnostic checklist with you. If it is determined that the product needs to be returned for service or
exchanged, you will receive a return merchandise authorization (RMA) number. The representative
will give you complete shipping details. Do not return products to zBoost without a Return
Authorization Number.
To get out of warranty service…
To obtain out of warranty service, contact zBoost at 1-800-871-1612 or support@zBoost.com for
information on the possibility of any costs for repair or replacement of out-of-warranty products.
Reminder
Record the model and serial number found on the product below:
Your warranty does NOT cover:
•
Labor charges for set up of the unit.
Model #: ___________________________________
•
Product replacement because of misuse, accident, lightning damage, unauthorized repair or
other cause not within the control of zBoost.
Serial #: ___________________________________
•
Incidental or consequential damages resulting from the product. Some states do not allow
the exclusion of incidental or consequential damages, so the above exclusion may not apply
to you.
•
Any modifications or other changes to the product, including but not limited to software or
hardware modifications in any way other than as expressly authorized by zBoost will void
this limited warranty.
•
Product that has been modified or adapted to enable it to operate in any country other than
the country for which it was designed, manufactured, approved and/or authorized, or repair
of products damaged by these modifications.
14
Purchase Date: _____________________________
15

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2014:03:19 13:52:44-04:00
Create Date                     : 2014:03:19 13:52:44-04:00
Format                          : application/pdf
Title                           : ZB575X-Manual.indd
Creator                         : bmangold
Producer                        : Acrobat Distiller 10.0.0 (Windows)
Document ID                     : uuid:462535a5-d79f-4a15-92ff-36f7d4ced18c
Instance ID                     : uuid:75770a34-1495-4c11-9f42-3096e9bb342a
Page Count                      : 11
Author                          : bmangold

EXIF Metadata provided by EXIF.tools