Accton Technology WA6101BCC WLAN Access Point 2221 User Manual AccessPointUG
Accton Technology Corp WLAN Access Point 2221 AccessPointUG
Manual
Part No. 214853-B June 2003 4655 Great America Parkway Santa Clara, CA 95054 Using the Nortel Networks Wireless LAN Access Point 2220/2221-802.11b-only This multi-product manual describes some features not available on the 2221-802.11b-only Access Point. The 802.11a radio described in this manual is unavailable on the 2221-802.11b-only Access Point. 2 Copyright © 2003 Nortel Networks All rights reserved. June 2003. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Windows 98SE/2000/ME/XP are trademarks of Microsoft Corp. Pentium is a trademark of Intel. Nortel Networks and the Nortel Networks logo are trademarks of Nortel Networks, Inc. Multi-Region Product Documentation This document may describe features that are not available in your region due to local regulations. This document describes the use of the 802.11a radio. This feature is unavailable in Israel, Greece and Spain due to local regulations. Compliances Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. European Community Notice Marking by the symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: EN 301 893, EN 301 489-17, EN 60950, ETS 300 328-2 This device should not be operated in 802.11a mode in the following European Community countries: Greece and Spain. The radio spectrum authorities in these countries do not currently allow operation of this radio device in the 5GHz bands. 214853-B 3 This device is restricted to indoor use when operated in the European Community using channels in the 5150-5350 MHz band to reduce the potential for harmful interference to other users of the band. To remain in conformance with European National spectrum usage laws, the channel and power settings must be configured during installation to match the country in which the device is operating. This will ensure the Access Point operates using the channels and transmit power specified by the applicable radio regulatory authority (refer to table below). Please refer to the Radio Interface sections of the using guide to configure the channel and power settings. Allowable Frequencies of Operation Countries 5150-5250 MHz (Channels 36, 40, 44, 48) Austria, Germany, Liechtenstein, Switzerland 5150-5350 MHz (Channels 36, 40, 44, 48, 52, 56, 60, 64) Belgium, France, Ireland, U.K. 5150-5350 & 5470-5725 MHz (Channels 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140) Denmark, Finland, Iceland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden 2446.5Mhz - 2483.5Mhz (Channels 10,11,12,13) France European Community Declaration of Conformity: English Hereby, Nortel Networks, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Finnish Valmistaja Nortel Networks vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Dutch Hierbij verklaart Nortel Networks dat het toestel Radio LAN device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG Bij deze verklaart Nortel Networks dat deze Radio LAN device voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC. French Par la présente Nortel Networks déclare que l'appareil Radio LAN device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE Par la présente, Nortel Networks déclare que ce Radio LAN device est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables Swedish Härmed intygar Nortel Networks att denna Radio LAN device står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Danish Undertegnede Nortel Networks erklærer herved, at følgende udstyr Radio LAN device overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF German Hiermit erklärt Nortel Networks, dass sich dieser/diese/dieses Radio LAN device in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi) Using the Nortel Networks Wireless LAN Access Point 2220/2221 4 Hiermit erklärt Nortel Networks die Übereinstimmung des Gerätes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien) Greek Ã≈ ‘«Õ —¡–œ’”¡ Nortel Networks ƒ«ÀŸÕ≈… œ‘… Radio LAN device ”’ÃÃœ–÷ŸÕ≈‘¡… —–œ” ‘…” œ’”…Ÿƒ≈…” ¡—¡…‘«”≈…” ¡… ‘…” Àœ…—≈” ”◊≈‘… ≈” ƒ…¡‘¡Œ≈…” ‘«” œƒ«√…¡” 1999/5/≈ Italian Con la presente Nortel Networks dichiara che questo Radio LAN device è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Spanish Por medio de la presente Nortel Networks declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/ 5/CE Portuguese Nortel Networks declara que este Radio LAN device está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. CAUTION STATEMENT: FCC Radiation Exposure Statement FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters (8 inches) between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device is restricted to indoor use only. Industry Canada - Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications. Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des Communications. Warning: Use ONLY the power adapter supplied by Nortel Networks for this product. Otherwise, the product may be damaged. Contact your Nortel Networks representative to order the power adapter. Warning: To avoid bodily injury from hazardous electrical shock and current, never remove the top cover of the device. There are no user-serviceable components inside. 214853-B 5 Warning: Um gesundheitliche Schäden zu vermeiden, öffnen Sie nie den oberen Gehäusedeckel. Es befinden sich keine durch den Benutzer zu wartenden Teile im Inneren. Warning: pour éviter tout risque d’électrocution, ne retirez jamais le couvercle du module. Celui-ci ne comprend aucun composant pouvant être dépanné par l’utilisateur. Advertencia: No retire nunca la cubierta superior del dispositivo, ya que podría resultar herido como consecuencia de una descarga eléctrica y de corriente. Dentro del dispositivo no hay ningún componente que pueda reparar el usuario. Avviso: per evitare lesioni personali da scosse elettriche e tensioni pericolose, non rimuovere mai il coperchio superiore del dispositivo. Questo prodotto non contiene parti riparabili dall’utente. Using the Nortel Networks Wireless LAN Access Point 2220/2221 6 214853-B 7 Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Package Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Ethernet Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Power over Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Chapter 1 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Chapter 2 Network Configuration and Planning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Network Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ad Hoc Wireless LAN (no AP or Bridge) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Infrastructure Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Infrastructure Wireless LAN for Roaming Wireless PCs . . . . . . . . . . . . . . . . . . . . 22 Chapter 3 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Accessing the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Using the Web Management Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 802.11a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 802.11b . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Using the Nortel Networks Wireless LAN Access Point 2220/2221 8 Contents Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 64-Bit Manual Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 128-Bit Manual Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 TCP / IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 RADIUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 PPPoE Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 802.1x Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Local MAC Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Filter Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Change Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Restore Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Reset Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 SNTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Radio Interface B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Radio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Radio Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Maximum Station Data Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Beacon Interval (20-1000) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 DTIM Period (1-16384) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 RTS Threshold (0-2347) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Preamble Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 WEP (Wired Equivalent Privacy) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Authentication Type Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Data Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Standard Key Setup (WEP Default: 128) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 214853-B Contents Radio Interface A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Radio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Turbo Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Radio Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Auto Channel Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Transmit Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Maximum Station Data Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Beacon Interval (20-1000) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 DTIM Period (1-16384) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 RTS Threshold (0-2347) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 WEP (Wired Equivalent Privacy) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Authentication Type Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Data Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Standard Key Setup (WEP Default: 128) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Access Point Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Station Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Event Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Appendix A Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Available Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Maximum Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Data Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Operating Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Physical Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Using the Nortel Networks Wireless LAN Access Point 2220/2221 10 Contents Compliance Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Appendix B Template for placing the Access Point 2220/2221. . . . . . . . . . . . . . . . . . . . 65 Appendix C Mounting the Access Point 2220/2221 on a Drop Ceiling . . . . . . . . . . . . . . 67 Attaching the mounting bracket to a drop ceiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Attaching the Access Point 2220/2221 to the mounting bracket . . .. . . . . . . . . . . . . . . 68 214853-B 11 Figures Figure 1 LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 2 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 3 Login screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 4 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 5 Setup Wizard screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Figure 6 SSID screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Figure 7 Channel screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Figure 8 TCP/IP Settings screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Figure 9 Security screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Figure 10 Advanced Setup screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Figure 11 Identification screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Figure 12 TCP/IP Settings screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Figure 13 RADIUS screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Figure 14 PPPoE Setup screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Figure 15 Authentication screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Figure 16 Filter Control screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Figure 17 SNMP screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Figure 18 Administration screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Figure 19 System Log screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Figure 20 Radio Settings screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Figure 21 Security screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Figure 22 Radio Settings screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Figure 23 Security screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Figure 24 Status screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Figure 25 AP Status screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Figure 26 Station Status screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Figure 27 Event Logs screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Figure 28 Optional mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Using the Nortel Networks Wireless LAN Access Point 2220/2221 12 Figures 214853-B 13 Tables Table 1 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table 2 802.1x Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Table 3 Local MAC Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Using the Nortel Networks Wireless LAN Access Point 2220/2221 14 Tables 214853-B 15 Preface Note: Both 802.11a and 802.11b radios are turned off on your Nortel Networks Wireless LAN Access Point 2220/2221. You must configure your Access Point 2220/2221 for your country before turning on the 802.11a and 802.11b radios. For information on country-specific configuration, refer to Country-specific Configuration for the Nortel Networks Wireless LAN Access Point 2220/2221 (part number 215293-B). Go to http://support.nortelnetworks.com/, select “Wireless LAN” and then “WLAN Access Point 2220” or “WLAN Access Point 2221”. Introduction The Nortel Networks* Wireless LAN Access Point 2220/2221 (Access Point 2220/2221) is an access point that provides transparent, wireless high-speed data communications between the wired LAN and fixed, portable or mobile devices equipped with an 802.11a and/or 802.11b wireless adapter employing the same radio modulation. This solution offers fast, reliable wireless connectivity with considerable cost savings over wired LANs (which include long-term maintenance overhead for cabling). Using 802.11a/802.11b technology, the Access Point 2220/2221 can easily replace a 10 Mbps Ethernet connection or seamlessly integrate into a 10/ 100 Ethernet LAN. Using the Nortel Networks Wireless LAN Access Point 2220/2221 16 Preface Package Checklist The Access Point 2220/2221 package includes: • • • One Access Point 2220/2221 Driver & Utility CD Documentation CD Hardware Description Ethernet Compatibility The Access Point 2220/2221 can attach directly to 10BASE-T/100BASE-TX (twisted-pair) Ethernet LAN segments. These segments must conform to the IEEE 802.3 specification. The access point is an Ethernet node which switches packets from the remote devices on the wireless infrastructure to the wired LAN and vice versa. Power over Ethernet The Access Point 2220/2221 supports Power over Ethernet (PoE). To use PoE to power the Access Point 2220/2221, connect a 4-pair Cat 5 (or better) cable to the RJ-45 port on the rear of the Access Point 2220/2221. Connect the other end of the cable to an ethernet switch capable of delivering IEEE 802.3af-draft-compliant power. The Access Point 2220/2221 draws 8.5 W. When using PoE, the Access Point 2220/2221 does not require the use of seperate AC power and the AC power adapter should not be used. LED Indicators The Access Point 2220/2221 includes four status LED indicators, as described in the following figure and table (Figure 1). 214853-B Preface 17 Figure 1 LED indicators Power Ethernet Link/Activity 802.11b 802.11a Wireless Wireless Link/Activity Link/Activity Table 1 LED Indicators LED Status Description Ready On Indicates that power is being supplied. Flashing Indicates • running a self-test • loading software program system errors LAN WLANa WLANb On Indicates a valid 10/100 Mbps Ethernet cable link. Flashing Indicates that the access point is transmitting or receiving data on a 10/100 Mbps Ethernet LAN. Flashing rate is proportional to your network activity. On Indicates a valid 802.11a wireless link. Very Slow Flashing Searching for network association. Slow Flashing Associated with network but no activity. Fast Flashing Indicates that the access point is transmitting or receiving data through wireless links. Flashing rate is proportional to network activity. On Indicates a valid 802.11b wireless link. Very Slow Flashing Searching for network association. Slow Flashing Associated with network but no activity. Fast Flashing Indicates that the access point is transmitting or receiving data through wireless links. Flashing rate is proportional to network activity. Using the Nortel Networks Wireless LAN Access Point 2220/2221 18 Preface System Requirements Before you install the Access Point 2220/2221, be sure you can meet the following requirements: • • • An AC power outlet (100~240 V, 50~60 Hz) or an IEEE 802.3af-draft-compliant power source 802.11a or 802.11b compliant (or dual-compliant) wireless Ethernet adapters with TCP/IP compatible protocol installed Web browser for configuration Alternatively, you can connect an RS-232 cable to the console port and use the command line interface (CLI). For more information on the CLI, refer to Run Time Console Specifications. Nortel Networks Optivity* NMS supports the Access Point 2220/2221. 214853-B 19 Chapter 1 Hardware Installation Note: Both 802.11a and 802.11b radios are turned off on your Nortel Networks Wireless LAN Access Point 2220/2221. You must configure your Access Point 2220/2221 for your country before turning on the 802.11a and 802.11b radios. For information on country-specific configuration, refer to Country-specific Configuration for the Nortel Networks Wireless LAN Access Point 2220/2221 (part number 215293-B). Go to http://support.nortelnetworks.com/, select “Wireless LAN” and then “WLAN Access Point 2220” or “WLAN Access Point 2221”. Placement of the Access Point 2220/2221 – Choose a proper place for your Access Point 2220/2221. In general, the best location is at the center of your wireless coverage area, within line of sight of all wireless devices. Try to place the access point in a position that can best cover its Basic Service Set (BSS). Normally, the higher you place the access point, the better the performance. For proper ventilation, allow at least 1 inch (2.54 centimeters) clearance around the ventilation holes on your Access Point 2220/2221. (Refer to Appendix B, “Template for placing the Access Point 2220/2221,” for information on mounting the Access Point 2220/2221.) Note: Position the antennas on the Access Point 2220/2221 at right angles to one another (not as shown in Figure 2). Using the Nortel Networks Wireless LAN Access Point 2220/2221 20 Chapter 1 Hardware Installation Figure 2 Rear Panel Console Port RJ-45 Connector (PoE) 5 V DC Power Socket Connect the Console Port – Connect the console cable to the RS-232 console port for accessing the command-line interface. (Refer to “Run Time Console Specifications” for complete information on the CLI.) You can manage the access point through this console connection, or the Web management interface (refer to “System Configuration” on page 24.) Connect the Ethernet Cable – The Access Point 2220/2221 can be connected to a wireline network via a 10 or 100 Mbps Ethernet connection. Connect a Cat 5 (or higher) UTP cable between the Access Point 2220/2221 and another network device such as a hub or switch. If you are not using PoE, use the separately orderable power adapter – Connect the power adapter cable to the 5 VDC power socket on the rear panel. Warning: Use ONLY the power adapter supplied by Nortel Networks for this product. Otherwise, the product may be damaged. Contact your Nortel Networks representative to order the power adapter. 214853-B Chapter 2 Network Configuration and Planning 21 Chapter 2 Network Configuration and Planning The wireless solution supports a stand-alone wireless network configuration as well as an integrated configuration with 10/100 Mbps Ethernet LANs. The wireless network cards, adapters, access points and wireless access point can be configured as: • • • Ad hoc for departmental LANs Infrastructure for wireless LANs Infrastructure wireless LAN for roaming wireless PCs Network Topologies Ad Hoc Wireless LAN (no AP or Bridge) Ad-hoc mode is also called “peer-to-peer mode” or “Independent Basic Service Set (IBSS).” In ad hoc mode, devices communicate directly with each other without using an access point. Ad Hoc Wireless LAN Notebook with Wireless USB Adapter Notebook with Wireless PC Card PC with Wireless An ad hoc wireless LAN consists of a group PCI Adapter of computers, each equipped with a wireless adapter, connected via radio signals as an independent wireless LAN. Computers in a specific ad hoc wireless LAN must therefore be configured to the same radio channel. An ad hoc wireless LAN can be used for a branch office operation. Using the Nortel Networks Wireless LAN Access Point 2220/2221 22 Chapter 2 Network Configuration and Planning Infrastructure Wireless LAN The access point can also provide access to a wired LAN for wireless workstations. An integrated wired/wireless LAN is called an Infrastructure configuration. A Basic Service Set (BSS) consists of a group of wireless PC users, and an access point that is directly connected to the wired LAN. Each wireless PC in this BSS can talk to any computer in its wireless group via a radio link, or access other computers or network resources in the wired LAN infrastructure via the access point. The infrastructure configuration not only extends the accessibility of wireless PCs to the wired LAN, but also increases the effective wireless transmission range for wireless PCs by passing their signal through one or more access points. A wireless infrastructure can be used for access to a central database, or for connection between mobile workers, as shown in the following figure. Wired LAN Extension to Wireless Adapters File Server Desktop PC Switch Notebook with Wireless PC Card Adapter Access Point PC with Wireless PCI Adapter Infrastructure Wireless LAN for Roaming Wireless PCs The Basic Service Set (BSS) is the communications domain for each wireless access point. For wireless PCs that do not need to support roaming, set the domain identifier (SSID) for the wireless card to the SSID of the access point to which you want to connect. Check with your administrator for the SSID of the access point or bridge to which he wants you to connect. 214853-B Chapter 2 Network Configuration and Planning 23 A wireless infrastructure can also support roaming for mobile workers. More than one access point can be configured to create an Extended Service Set (ESS). By placing the access points so that a continuous coverage area is created, wireless users within this ESS can roam freely. All Nortel Networks Wireless LAN--Series 2200 wireless network cards and adapters and Access Point 2220/2221 wireless access points within a specific ESS must be configured with the same SSID File Server Desktop PC Switch Notebook with Wireless PC Card Adapter Switch Access PointNotebook with Wireless PC Card Adapter Access Point Seamless Roaming PC with Wireless PCI Adapter Using the Nortel Networks Wireless LAN Access Point 2220/2221 24 Chapter 3 System Configuration Chapter 3 System Configuration Note: Both 802.11a and 802.11b radios are turned off on your Nortel Networks Wireless LAN Access Point 2220/2221. You must configure your Access Point 2220/2221 for your country before turning on the 802.11a and 802.11b radios. For information on country-specific configuration, refer to Country-specific Configuration for the Nortel Networks Wireless LAN Access Point 2220/2221 (part number 215293-B). Go to http://support.nortelnetworks.com/, select “Wireless LAN” and then “WLAN Access Point 2220” or “WLAN Access Point 2221”. The Access Point 2220/2221 can be configured by any Java-supported Web browser including Internet Explorer 4.0 or above, or Netscape Navigator 6.0 or above. Using the Web management interface, you may configure the Access Point 2220/2221. You can also use the command line interface (CLI) to manage the Access Point 2220/2221. Accessing the CLI You access the CLI using Telnet or a direct serial connection to the unit from a terminal or personal computer (PC). You can use any terminal or PC with a terminal emulator as the CLI command station. If using a direct connection via the console port, make sure the terminal has the following features: • • • 214853-B 9600 bits per second (b/s), 8 data bits, 1 stop bit, no parity, no flow control Serial terminal-emulation program Null modem cable and connector to match the female DB-9 connector on the Access Point 2220/2221 console port Chapter 3 System Configuration 25 Telnet or open the console connection to the Access Point 2220/2221. When you have connected to the Access Point 2220/2221, you will see the following prompt: Username: Enter: nortel You will see the following prompt: Password: The default is no password. Press Enter. The EXEC mode prompt appears: Nortel Enterprise AP# For a list of commands available from the CLI, refer to Run Time Console Specifications (part number 215113-A). Using the Web Management Interface To initially manage the Access Point 2220/2221 using the web management interface, you must configure the network settings of the computers on your wireless LAN to use the same IP subnet as the Access Point 2220/2221. The default network settings assuming there is no external DHCP server for this device are: Access Point IP Address: 192.168.168.10 Gateway IP Address: 192.168.168.254 Subnet Mask: 255.255.255.0 The IP address of the connected client PC from which system configuration is to be performed should be 192.168.168.x (where x means 1–9, 11–253). Using the Nortel Networks Wireless LAN Access Point 2220/2221 26 Chapter 3 System Configuration If DHCP is enabled, (default setting is “Enable,” page 48) and a DHCP server is located on the network, then the access point will automatically be assigned an IP address when booted. To access the Access Point 2220/2221’s management interface, enter the IP address of the device in your Web browser: http://192.168.168.10 The Web management window will appear. Setup Wizard Note: Both 802.11a and 802.11b radios are turned off on your Nortel Networks Wireless LAN Access Point 2220/2221. You must configure your Access Point 2220 for your country before turning on the 802.11a and 802.11b radios. For information on country-specific configuration, refer to Country-specific Configuration for the Nortel Networks Wireless LAN Access Point 2220/2221 (part number 215293-B). Go to http://support.nortelnetworks.com/, select “Wireless LAN” and then “WLAN Access Point 2220” or “WLAN Access Point 2221”. To access the management interface (Figure 3), enter the username “nortel” and click “LOGIN.” Note: There is no password by default. 214853-B Chapter 3 System Configuration 27 Figure 3 Login screen The home page displays the Main Menu (Figure 4). Figure 4 Main Menu Click “Setup Wizard” to open the “1-2-3” Setup Wizard (Figure 5). Using the Nortel Networks Wireless LAN Access Point 2220/2221 28 Chapter 3 System Configuration Figure 5 Setup Wizard screen Click the “Next” button to start basic configuration (Figure 6). SSID – The Service Set ID. This should be set to the same value as other wireless devices in your network. (Default: Nortel) Note: The SSID is case sensitive and can consist of up to 32 alphanumeric characters. Figure 6 SSID screen 214853-B Chapter 3 System Configuration 29 Channel Note: Both 802.11a and 802.11b radios are turned off on your Nortel Networks Wireless LAN Access Point 2220/2221. You must configure your Access Point 2220/2221 for your country before turning on the 802.11a and 802.11b radios. For information on country-specific configuration, refer to Country-specific Configuration for the Nortel Networks Wireless LAN Access Point 2220/2221 (part number 215293-B). Go to http://support.nortelnetworks.com/, select “Wireless LAN” and then “WLAN Access Point 2220” or WLAN Access Point 2221”. 802.11a Enable: Check this box to enable the 802.11a radio of your Access Point 2220/ 2221. By default the radio is not enabled. 802.11a Turbo Mode: When turbo mode is enabled, the Access Point 2220/2221 operates with a data rate of up to 108 Mbps. By default, turbo mode is disabled, and the Access Point 2220/2221 operates at a data rate of up to 54 Mbps. When you select Turbo Mode, the Access Point 2220/2221 uses two adjacent 802.11a channels to achieve the bandwidth. Note: The use of Turbo Mode is not allowed in all regions. Before enabling Turbo Mode, verify that Turbo Mode is allowed under your current local regulations. 802.11a Radio Channel: If auto channel select is not enabled, this option allows a specific channel to be selected. Auto Channel Select: Selecting “Enable” allows for automatic radio channel detection. Automatic radio channel detection only occurs at boot-up. (Default: “Enable”) 802.11b Enable: Check this box to enable the 802.11b radio of your Access Point 2220/ 2221. By default the radio is not enabled. Using the Nortel Networks Wireless LAN Access Point 2220/2221 30 Chapter 3 System Configuration 802.11b: Set the operating radio channel number (Default: channel 11) Note: Available channel settings are limited by local regulations which determine which channels are available (Figure 7). Figure 7 Channel screen IP Configuration DHCP Client: With DHCP (Dynamic Host Configuration Protocol) Client enabled, the IP address, subnet mask, default gateway, and DNS address can be dynamically assigned to the access point by an external network DHCP server on the network. This device implements a DHCP client but not a DHCP server. (Default: Enable) If DHCP Client is not enabled, you must enter the IP address, subnet mask, default gateway, and one or more DNS (Domain Name Servers) addresses (Figure 8). 214853-B Chapter 3 System Configuration 31 Figure 8 TCP/IP Settings screen Security WEP – Wired Equivalent Privacy (WEP) is implemented in this device to prevent unauthorized access to your wireless network (Figure 9). Authentication Type: Click on the “Shared Key” radio button to start filtering the frames with the addresses defined in the “Shared Key Setup” field. Enabling the shared key gives the option to encrypt the data. (Default: Open System) Shared Key Setup: For more secure data transmission, check the “Enable” radio button in the “Data Encryption” field. Then select one shared key size and the key number. (WEP Default: Disable) Note: If you select Shared Key, you must enable Data Encryption. Using the Nortel Networks Wireless LAN Access Point 2220/2221 32 Chapter 3 System Configuration Figure 9 Security screen The Access Point 2220/2221 supports “Shared Key” encryption with key lengths of the standard 64-bit and industry standard 128-bit. The bit key can be in alphanumeric characters, or hexadecimal numerals (0-9, A-F, e.g., D7 0A 9C 7F E5.) All wireless devices must have the same Key ID values to communicate. 64-Bit Manual Entry Key 1-4 - Each Key ID contains 10 HEX digits, or 5 alphanumeric characters. 128-Bit Manual Entry Key ID contains 26 HEX digits, or 13 alphanumeric characters. 214853-B Click “Finish.” Click the “OK” button to restart the access point. Chapter 3 System Configuration 33 Note: You must use the Advanced screens to do 152-bit encryption, which is available only on 802.11a. Advanced Setup Click “Advanced Setup” on the Home page to open the Advanced Setup page. (Figure 10). Figure 10 Advanced Setup screen Note: The “Advanced Setup” screen allows you to view and change the current configuration of the access point. After modifying the configuration parameters, you must click on the “Apply” button to save the changes. Using the Nortel Networks Wireless LAN Access Point 2220/2221 34 Chapter 3 System Configuration System Identification System Name: You can easily identify the access point by providing a descriptive name. Enter a maximum of 32 characters in the System Name field (Figure 11). SSID: The SSID (Service Set Identification) is the name of a Basic Service Set (BSS) provided by an access point. Clients that want to connect to the wireless network via an access point must set their SSIDs to the same as that of the access point. (SSID Default: Nortel). (The default system location is the MAC address.) Figure 11 Identification screen 214853-B Chapter 3 System Configuration 35 TCP / IP Settings Figure 12 TCP/IP Settings screen Note: You must disable DHCP for the manual TCP/IP addresses to be accepted (Figure 12). DHCP Client: With DHCP (Dynamic Host Configuration Protocol) Client enabled, the IP address, subnet mask and default gateway can be dynamically assigned to the access point by the network DHCP server. (Default: Enable) Note: If there is no DHCP server on your network, then the access point will automatically start up with its default IP address, 192.168.168.10. If DHCP Client is not enabled, you must enter the IP address, subnet mask, default gateway, and one or more DNS (Domain Name Servers) addresses. Enter those addresses on this screen (Figure 12). Using the Nortel Networks Wireless LAN Access Point 2220/2221 36 Chapter 3 System Configuration RADIUS Figure 13 RADIUS screen Remote Authentication Dial-in User Service (RADIUS) is a logon authentication protocol that uses software running on a central server to control access to RADIUS-compliant devices on the network. It allows a wireless access point to send the connection parameters to a RADIUS server. Enter the required parameters as shown on the screen, which includes the RADIUS server IP address, controlled port number, per-client unicast session key, timeout value (in seconds), and retransmit attempts number (Figure 13). The following RADIUS servers are supported by the Access Point 2220/2221: • • Microsoft IAS: Windows 2000 Server Build 2195 Service Pack 2: TLS Funk Odyssey Server (Version 1.0): TTLS, TLS IP Address – Address of authentication server. (Default: 0.0.0.0) Port – Network (UDP) port of authentication server used for authentication messages (Range: 1-65535; Default: 1812) Key – Encryption key (password) used to authenticate logon access for client. Do not use blank spaces in the string. (Maximum length: 255 characters) 214853-B Chapter 3 System Configuration 37 Timeout – The number of seconds the access point waits for a reply from the RADIUS server before it resends the request. (Range: 1-60; Default: 5) Retransmit attempts – Number of times the access point will try to authenticate logon access via the authentication server. (Range: 1-30; Default: 3) PPPoE Settings Figure 14 PPPoE Setup screen Enter the PPPoE user name and password assigned by your Service Provider (Figure 14). The Service Name is normally optional, but may be required by some service providers. Some xDSL Internet Service Providers may assign a fixed (static) IP address. If you have been provided with this information, click on the “Static assigned” for the “IP Allocation Mode,” and enter the assigned “Local IP Address” and “Remote IP addresses.” Using the Nortel Networks Wireless LAN Access Point 2220/2221 38 Chapter 3 System Configuration Authentication Figure 15 Authentication screen Management access will be checked against the authentication database stored on the access point (Figure 15). If a remote authentication server is used, you must specify the authentication sequence and the corresponding parameters (see “RADIUS” on page 36) for the remote authentication protocol. MAC Authentication (Default: Local MAC) Selecting the MAC authentication allows you to define access permission and precedence. For Local MAC Authentication go to page 39. For RADIUS MAC Authentication see the following page. Note: Be sure to set up the RADIUS MAC authentication for the client on the Radius server before using the RADIUS MAC service. 214853-B Chapter 3 System Configuration 39 802.1x Setup Click the “Supported” or “Required” radio button on the 802.1x Setup field when using the Radius MAC authentication. Table 2 802.1x Setup Field Defaults Description Broadcast Key Refresh Rate 0 (in minutes) Defines how long the radius server will refresh the primary broadcast key Session Key Refresh Rate 0 (in minutes) Defines how long the radius server will dynamically re-assign a session key to a connected client station. 802.1x Reauthentication Refresh Rate 0 (in seconds) Defines how long the radius server will dynamically re-assign session keys to the all connected client stations. Local MAC Authentication Client computers can be filtered using the unique MAC address of their IEEE 802.11 network card. To secure an access point using local MAC address filtering, you must enter a list of allowed/denied client MAC addresses into the filtering table. Table 3 Local MAC Authentication Parameter Description System Default Define the default filtering setting as “Deny” or “Allow.” MAC Address Manually type in the MAC address of a client for the access control Permissions Allows/Denies access of devices matching a specified source IP address in the list to connect to the access point. Update Click the “Update” button to refresh the settings. Using the Nortel Networks Wireless LAN Access Point 2220/2221 40 Chapter 3 System Configuration Filter Control Figure 16 Filter Control screen Local Bridge Filter Using this filter function (Figure 16) prevents direct node-to-node connection through the Access Point 2220/2221, for a more secure wireless network. The Local Bridge Filter does not restrict ad hoc connections between clients. (Default: Disable) AP Management Filter The administration management can be protected with AP Management Filter. (Default: Enable) 214853-B Chapter 3 System Configuration 41 Ethernet Type Filter Use the “Ethernet Type Filter” table to filter out Ethernet packet frames matching Ethernet protocol type. (Default: Disable) SNMP Figure 17 SNMP screen Use this screen to display and enter a community string for the Simple Network Management Protocol (SNMP). To communicate with the access point, the SNMP agent must first be enabled, and the Network Management Station must submit a valid community string for authentication (Figure 17). Location - Specifies the access point location Contact - Set the system location string, that describes the system location. (Maximum length: 255 characters) Community Name (Read Only) - Specifies a community string with read-only access. Authorized management stations are only able to retrieve MIB objects. (Maximum length: 23 characters) Using the Nortel Networks Wireless LAN Access Point 2220/2221 42 Chapter 3 System Configuration Community Name (Read/Write) - Specifies a community string with read-write access. Authorized management stations are able to both retrieve and modify MIB objects. (Maximum length: 23 characters) Trap Destination IP Address - Fill in the IP address box for a trap manager that will receive these messages. Trap Destination Community Name - Fill in the community string box for a trap manager that will receive these messages. (Maximum length: 23 characters) Administration Figure 18 Administration screen 214853-B Chapter 3 System Configuration 43 Change Password Use this section to change the password on the access point (Figure 18). Firmware Upgrade Note: You must disable the radios prior to upgrading the Access Point 2220/2221 or the upgrade may not occur. Local - Click “Browse” to locate the downloaded firmware file and click “Start Upgrade” to start the upgrade process. Remote - Select FTP or TFTP, and enter firmware file name, the host IP address, user name, and password. (You need your user name and password only with the FTP.) Click “Start Upgrade” to start the upgrade process. For latest firmware version information, go to the Nortel Networks customer support web site at: http://support.nortelnetworks.com/, select “Wireless LAN” and then “WLAN Access Point 2220” or “WLAN Access Point 2221” and then “Software.” Restore Factory Settings Click the “Restore” button to load the factory default configuration and reboot this device. Note that all user configured information will be lost. You will also have to re-enter the default user name (nortel) to regain management access to this device. Reset Access Point Clicking on the “Reset” button to perform a hardware reset of the access point. Note: Although current configurations will not be changed, you must reset the time. (The default time setting is January 1 at midnight.) Using the Nortel Networks Wireless LAN Access Point 2220/2221 44 Chapter 3 System Configuration System Log Figure 19 System Log screen The System Log Setup (Figure 19) allows you to setup a log server with various logging level (as shown on the above screen). (Default: Disable) SNTP Server Allows you to enter Simple Network Time Protocol (SNTP) Server information for a primary and secondary SNTP Server. (Default: Enable) You may also set your time zone and daylight savings information (as shown on the above screen). 214853-B Chapter 3 System Configuration 45 Radio Interface B Note: Both 802.11a and 802.11b radios are turned off on your Nortel Networks Wireless LAN Access Point 2220/2221. You must configure your Access Point 2220/2221 for your country before turning on the 802.11a and 802.11b radios. For information on country-specific configuration, refer to Country-specific Configuration for the Nortel Networks Wireless LAN Access Point 2220/2221 (part number 215293-B). Go to http://support.nortelnetworks.com/, select “Wireless LAN” and then “WLAN Access Point 2220” or “WLAN Access Point 2221”. Radio Settings Figure 20 Radio Settings screen Enable Check this box to enable the 802.11b radio of your Access Point 2220/2221. By default the radio is not enabled. Using the Nortel Networks Wireless LAN Access Point 2220/2221 46 Chapter 3 System Configuration Radio Channel The radio channel (Figure 20) is the channel number used for communication between the access point and its BSS. (Default: channel 11) Note: The available channel settings are limited by local regulations, which determine the number of channels that are available. (For more information specific to each country’s configuration, refer to Country-specific Configuration for the Nortel Networks Wireless LAN Access Point 2220/2221 (part number 215293-B). Go to http://support.nortelnetworks.com/, select “Wireless LAN” and then “WLAN Access Point 2220” or “WLAN Access Point 2221”. Maximum Station Data Rate Select the appropriate data rate from the drop-down list for the data transfer speed running on your network. (Default: 11 Mbps) Note: Nortel Networks recommends you do not change any default settings. Beacon Interval (20-1000) Sets the beacon signal interval. The beacon signals allow the wireless devices to maintain contact with each other. They may also carry power-management information. (Default: 100 TU) DTIM Period (1-16384) Sets the Delivery Traffic Indication Message (DTIM) packet interval value. The DTIM informs the client that the access point has broadcast and multicast traffic to send. This parameter is necessary to wake up stations that are using Power Save mode. 214853-B Chapter 3 System Configuration 47 The DTIM is the interval between two synchronous frames with broadcast information. If you set the value to 2, the access point saves broadcast and multicast packets and forwards them after every second beacon. Having smaller DTIM intervals delivers broadcast and multicast frames in a more timely manner; however, by causing stations in Power Save mode to wake up more often, smaller DTIM intervals drain power faster. Conversely, having higher DTIM values delays the transmission of broadcast and multicast frames, but the larger DTIM intervals reduces the power used by stations in Power Save mode. (Default: 5 Beacons) RTS Threshold (0-2347) Set the RTS (Request to Send) frame length. You may configure the access point to initiate an RTS frame sequence always, never, or only on frames longer than a specified length. If the packet size is smaller than the preset RTS threshold size, the RTS/CTS mechanism will NOT be enabled When the RTS/CTS mechanism is enabled, the access point sends Request to Send (RTS) frames to a particular receiving station to negotiate the sending of a data frame. After receiving an RTS frame, the station sends a CTS (Clear to Send) frame to acknowledge the right of the sending station to send data frames. The access points contending for the media may not be aware of each other. The RTS/ CTS mechanism allows other access points in the vicinity to see the CTS and become quiet while the first access point transmits frames. (This mechanism should be enabled on both the clients and the access points.) (Default: 2347) Preamble Setting The access points and client card drivers have a radio setting for RF Preamble. Set it to short for better throughput; although this setting may cause interoperability issues with some NICs. (Default: Long) Using the Nortel Networks Wireless LAN Access Point 2220/2221 48 Chapter 3 System Configuration Security WEP (Wired Equivalent Privacy) Figure 21 Security screen WEP is implemented in this device to prevent unauthorized access to your wireless network (Figure 21). The WEP setting must be the same on each client in your wireless network. Authentication Type Setup You may choose either “Open System” or “Shared Key.” (Default: Open System) If Shared Key is enabled, WEP should be enabled and at least one shared key should be defined. 214853-B Chapter 3 System Configuration 49 Data Encryption You may choose “Enable” to enhance your network security with WEP data encryption (Default: Disable) If Shared Key is enabled, WEP should be enabled and at least one shared key should be defined. Standard Key Setup (WEP Default: 128) Default Shared Key – Choose the Shared Key that has the encryption string you prefer (Key 1-3). The access point supports “Shared Key” encryption with key lengths of the standard 64-bit and industry standard 128-bit. The bit key can be in alphanumeric characters, or hexadecimal numerals (0-9, A-F, e.g., D7 0A 9C 7F E5.) 64-Bit Manual Entry Key 1-3 - Each Key ID contains 10 HEX digits, or 5 alphanumeric characters. 128-Bit Manual Entry Key ID contains 26 HEX digits, or 13 alphanumeric characters. Note: All wireless devices must have the same Key ID values to communicate. Select a unique key (1-3) Enter the encryption key and select the key size. Be sure to click the “Apply” button on the bottom of the page to make the settings take effect. Note: The 152-bit encryption is only available with the 802.11a Radio. Using the Nortel Networks Wireless LAN Access Point 2220/2221 50 Chapter 3 System Configuration Radio Interface A Note: Both 802.11a and 802.11b radios are turned off on your Nortel Networks Wireless LAN Access Point 2220/2221. You must configure your Access Point 2220/2221 for your country before turning on the 802.11a and 802.11b radios. For information on country-specific configuration, refer to Country-specific Configuration for the Nortel Networks Wireless LAN Access Point 2220/2221 (part number 215293-B). Go to http://support.nortelnetworks.com/, select “Wireless LAN” and then “WLAN Access Point 2220” or “WLAN Access Point 2221”. Radio Settings Figure 22 Radio Settings screen Enable Check this box to enable the 802.11a radio of your Access Point 2220/2221. By default the radio is not enabled. 214853-B Chapter 3 System Configuration 51 Turbo Mode You may either “Enable” or “Disable” the “Turbo Mode.” (Default: Disable) “Turbo Mode” is an enhanced wireless LAN operating mode (not regulated in the standard IEEE 802.11a) that can provide a higher data rate. The “Normal Mode” of the 802.11a access point provides connections up to 54 Mbps. Enabling “Turbo Mode” on the 802.11a access point allows the access point to provide connections up to 108 Mbps (Figure 22). When you select Turbo Mode, the Access Point 2220/2221 uses two adjacent 802.11a channels to achieve the bandwidth. Note: The use of Turbo Mode is not allowed in all regions. Before enabling Turbo Mode, verify that Turbo Mode is allowed under your current local regulations. Radio Channel The radio channel through which the access point communicates to PCs in its BSS. Note that the client channel for wireless users is automatically set to the same as that used by the access point to which it is linked. Note: The available channel settings are limited by local regulations, which determine the number of channels that are available. (For more information specific to each country’s configuration, refer to Country-specific Configuration for the Nortel Networks Wireless LAN Access Point 2220/2221 (part number 215293-B). Go to http://support.nortelnetworks.com/, select “Wireless LAN” and then “WLAN Access Point 2220” or “WLAN Access Point 2221”. Auto Channel Select Selecting “Enable” allows for automatic radio channel detection. Automatic radio channel detection only occurs at boot-up. (Default: “Enable”) Using the Nortel Networks Wireless LAN Access Point 2220/2221 52 Chapter 3 System Configuration Transmit Power Set the signal strength transmitted from the access point. The longer the transmission distance, the higher the transmission power required. (Default: 100%) Maximum Station Data Rate Select the appropriate data rate from the drop-down list for the data transfer speed running on your network. (Default: 54 Mbps) Note: Nortel Networks recommends that you do not change any default settings. Beacon Interval (20-1000) Sets the beacon signal interval. The beacon signals allow the wireless devices to maintain contact with each other. They may also carry power-management information. (Default: 100 TU) DTIM Period (1-16384) Sets the Delivery Traffic Indication Message (DTIM) packet interval value. The DTIM informs the client that the access point has broadcast and multicast traffic to send. This parameter is necessary to wake up stations that are using Power Save mode. The DTIM is the interval between two synchronous frames with broadcast information. If you set the value to 2, the access point saves broadcast and multicast packets and forwards them after every second beacon. Having smaller DTIM intervals delivers broadcast and multicast frames in a more timely manner; however, by causing stations in Power Save mode to wake up more often, smaller DTIM intervals drain power faster. Conversely, having higher DTIM values delays the transmission of broadcast and multicast frames, but the larger DTIM intervals reduces the power used by stations in Power Save mode. (Default: 5 Beacons) 214853-B Chapter 3 System Configuration 53 RTS Threshold (0-2347) Set the RTS (Request to Send) frame length. You may configure the access point to initiate an RTS frame sequence always, never, or only on frames longer than a specified length. If the packet size is smaller than the preset RTS threshold size, the RTS/CTS mechanism will NOT be enabled When the RTS/CTS mechanism is enabled, the access point sends Request to Send (RTS) frames to a particular receiving station to negotiate the sending of a data frame. After receiving an RTS frame, the station sends a CTS (Clear to Send) frame to acknowledge the right of the sending station to send data frames. The access points contending for the media may not be aware of each other. The RTS/ CTS mechanism allows other access points in the vicinity to see the CTS and become quiet while the first access point transmits frames. (This mechanism should be enabled on both the clients and the access points.) (Default: 2347) Using the Nortel Networks Wireless LAN Access Point 2220/2221 54 Chapter 3 System Configuration Security WEP (Wired Equivalent Privacy) Figure 23 Security screen Authentication Type Setup You may choose either “Open System” or “Shared Key.” (Default: Open System) If Shared Key is enabled, WEP is automatically enabled and at least one shared key must be defined (Figure 23). 214853-B Chapter 3 System Configuration 55 Data Encryption You may choose “Enable” to enhance your network security with WEP data encryption (Default: Disable) If Shared Key is enabled, WEP is automatically enabled and at least one shared key must be defined. Standard Key Setup (WEP Default: 128) Default Shared Key – Choose the Shared Key that has the encryption string you prefer (Key 1-3). The access point supports “Shared Key” encryption with key lengths from the standard 64-bit, industry standard 128-bit, to the extended 152-bit. The bit key can be in alphanumeric characters, or hexadecimal numerals (0-9, A-F, e.g., D7 0A 9C 7F E5.) 64-Bit Manual Entry Key 1-3 - Each Key ID contains 10 HEX digits, or 5 alphanumeric characters. 128-Bit Manual Entry Key ID contains 26 HEX digits, or 13 alphanumeric characters. 152-Bit Manual Entry Key ID contains 32 HEX digits, or 16 alphanumeric characters. Note: All wireless devices must have the same Key ID values to communicate. Select a unique key (1-3) Enter the encryption key and select the key size. Be sure to click the “Apply” button on the bottom of the page to make the settings take effect. Using the Nortel Networks Wireless LAN Access Point 2220/2221 56 Chapter 3 System Configuration Status Figure 24 Status screen Clicking on the “Status” radio button on the home page displays additional information about the access point status and station status as shown in the following section (Figure 24). 214853-B Chapter 3 System Configuration 57 Access Point Status Figure 25 AP Status screen On the Status page, click “AP Status” to view the access point system configuration and access point wireless configuration (Figure 25). Using the Nortel Networks Wireless LAN Access Point 2220/2221 58 Chapter 3 System Configuration Station Status Figure 26 Station Status screen Click “Station Status” to view connected station configuration (Figure 26). The “Station Statistics” page displays basic connection information for all associated stations. The page is automatically refreshed every five seconds. 214853-B Chapter 3 System Configuration 59 Event Logs Figure 27 Event Logs screen Click “Event Logs” to display the activity logs of the access point (Figure 27). Using the Nortel Networks Wireless LAN Access Point 2220/2221 60 Chapter 3 System Configuration 214853-B 61 Appendix A Specifications This appendix provides technical specifications for the Access Point 2220/2221. Available Channels Available channels will vary according to current local regulations. For information on configuring the Nortel Networks Wireless LAN Access Point 2220/2221 for the country you are in, go to http://support.nortelnetworks.com/ , select “Wireless LAN” and then “WLAN Access Point 2220” or “WLAN Access Point 2221”. Maximum Clients Settable range using the CLI is 0 to 2007; the default setting is 64. Data Rate Normal Mode: 6, 9, 12, 18, 24, 36, 48, 54 Mbps per channel Turbo Mode: 12, 18, 24, 36, 48, 72, 96, 108 Mbps per channel Operating Frequency 5.15 - 5.25 GHz (lower band) US/Canada, Japan 5.25 - 5.35 GHz (middle band) US/Canada 5.725 - 5.825 GHz (upper band) US/Canada Channel selection will vary according to current local regulations. Using the Nortel Networks Wireless LAN Access Point 2220/2221 62 Appendix A Specifications Power supply Input: 100-240 VAC, 50-60 Hz; Output: 5 VDC, 3 A Power over Ethernet (POE) circuitry: Input voltage 48 VDC, 12.95W maximum Output Power Maximum power setting will vary according to current local regulations. Physical Size 20.5 x 13.6 x 4 cm, (8.07 x 5.35 x 1.58 in) Weight 700 grams (1.5 lbs.) LED Indicators Ready (Power), LAN (Ethernet Link/Activity), WLANa and WLANb (Wireless Link/Activity) Management HTML Web-browser interface Command line interface (connection via the console port requires a serial terminal-emulation program and a nullmodem cable and connector to match the female DB-9 connector on the Access Point 2220/2221 console port.) Temperature Operating: 0 to 55 ºC (32 to 122 ºF) Storage: 0 to 70 ºC (32 to 158 ºF) 214853-B Appendix A Specifications 63 Humidity 5% to 95% (non-condensing) Compliance Standards Safety: UL 60950 CAN/CSA-22.2 No. 60950 IEC 60950/EN60950, CB certificate and report with all national deviations Radio Approvals: FCC Part 15.247 (2.4 GHz) FCC Part 15.401-15.407 (5 GHz) RSS-139-1, RSS-210 (Canada) EN 300.329 (Europe, 2.4 GHz) EN 301.893 (Europe, 5 GHz) EMI and Susceptibility (Class B): FCC Part 15.107 and 15.109 ICES-003 (Canada) EN 301.489-1 and -17 (Europe) Other: IEEE 802.11a and 802.11b FCC Bulletin OET-65C (Human exposure to RF Fields) RSS-102 (Canada) Standards IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.11a/b Support for Power over Ethernet, IEEE 802.3af Draft V3 Warranty Limited Lifetime Using the Nortel Networks Wireless LAN Access Point 2220/2221 64 Appendix A Specifications 214853-B 65 Appendix B Template for placing the Access Point 2220/2221 The template on the next page can be used to assist in positioning the Access Point 2220/2221. Mark where the wall-mount screws should go. For proper ventilation, allow at least 1 inch (2.54 centimeters) clearance around the ventilation holes on your Access Point 2220/2221. Note: Because of variations that exist from printer to printer, please verify that the template matches the mounting holes on the Access Point 2220/2221. Using the Nortel Networks Wireless LAN Access Point 2220/2221 67 Appendix C Mounting the Access Point 2220/2221 on a Drop Ceiling You can mount the Nortel Networks Wireless LAN Access Point 2220/2221 on a drop ceiling (sometimes referred to as an acoustic or suspended ceiling) using the optional mounting bracket (Figure 28). The bracket attaches to a drop ceiling T-rail and provides a mounting surface for the Access Point 2220/2221. Figure 28 Optional mounting bracket Drop ceiling T-rail Clamp Clamp Mounting bracket Washer nut Washer nut 10983EA Using the Nortel Networks Wireless LAN Access Point 2220/2221 68 Appendix C Mounting the Access Point 2220/2221 on a Drop Ceiling Attaching the mounting bracket to a drop ceiling To attach the mounting bracket to a drop ceiling: Loosen the two washer nuts to allow the T-rail clamps to slide freely. Do not remove the washer nuts. Place the mounting bracket in the desired location and position the T-rail clamps around the drop ceiling T-rail. Holding the T-rail clamps in place around the T-rail, tighten both washer nuts securely. Verify that the mounting bracket is now securely attached to the drop ceiling T-rail. Attach the Access Point 2220 to the mounting bracket. Attaching the Access Point 2220/2221 to the mounting bracket To attach the Access Point 2220/2221 to the mounting bracket: 214853-B Align the slotted mounting holes on the Access Point 2220/2221 with the mounting tabs on the bracket. Press the Access Point 2220/2221 against the bracket, inserting the mounting tabs into the slotted mounting holes. Slide the Access Point 2220/2221 so that the mounting tabs move into the narrow part of the slotted mounting holes. The spring clips will lock the Access Point 2220/2221 in place when it is properly positioned. Refer to See Chapter 1, “Hardware Installation,” on page 19 for instructions on positioning the antennae and connecting the Ethernet cable and power supply cable (if required) to the access point.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Create Date : 2003:06:17 15:18:48 Producer : Acrobat Distiller 4.0 for Windows Author : RONJAMES Title : AccessPointUG.book Creator : FrameMaker 5.5.6p145 Modify Date : 2003:07:11 17:58:07+08:00 Page Count : 68 Page Mode : UseOutlinesEXIF Metadata provided by EXIF.tools