Attenti ATT-830-2 Asset tracking transmitter User Manual ATT 830 2 Operation Manual
3M Residential Monitoring, Inc. Asset tracking transmitter ATT 830 2 Operation Manual
Attenti >
User Manual
![](/img.php?id=1399127&img=bg1.png)
Wireless Resident Monitoring
Solutions
Asset Tracking Device
Operational Instructions
The HomeFree system is designed to monitor special needs individuals in the
care center environment. The ATT (Asset Tracking Tag) is one of the many
unique elements of this system.
The ATT is a transmitter that is designed for installation on material assets
such as computers and printers located within the monitored area. When the
monitored item is in motion, the ATT transmits a signal that enables the item
to be tracked. The ATT is not for use outside the monitored area.
LED Indicator
![](/img.php?id=1399127&img=bg2.png)
Activating the Asset Tracking tag:
The ATT is turned off by the manufacturer before shipment and must be
activated before use. To activate, install the rear tamper plate onto the item
that requires tracking. Click the ATT onto the rear tamper plate; the LED
indicator flashes for 3 seconds indicating that the ATT has been activated
successfully.
Once in active mode, the ATT sends a status message to the monitoring
station (every 60 minutes) indicating the current battery status as well as the
location of the ATT. This status message is sent until the ATT is deactivated.
Motion Alert:
When the ATT detects motion, it sends a transmission every 20 seconds. The
ATT sends these transmissions until 2 minutes have expired without motion.
After 2 motion-free minutes, the ATT returns to Rest mode.
Tamper Alert:
If the ATT is removed from the tracked item (i.e. it becomes separated from
the rear tamper plate), a tamper signal shall be sent once every 20 seconds
for a period of one hour. After an hour, if the ATT is still separated from the
tracked item, a tamper signal shall be sent once every 60 minutes. After the
ATT has been in a tamper condition for 12 hours, it shall automatically
deactivate itself.
Deactivating the ATT:
Separate the ATT from its rear tamper plate. After 12 hours, the ATT
deactivates itself automatically.
![](/img.php?id=1399127&img=bg3.png)
FCC Notices
Note: The following is applicable only to the 318MHz version of this product.
FCC ID: QUX-ATT-830
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT
The equipment complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, 2. Increase the separation between the equipment
and the receiver, 3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected, 4. Consult the dealer or an experienced radio/TV technician
for help.
Changes or modifications not expressly approved by Elmo Tech Ltd could
void the user’s authority to operate the equipment.
In case of any problems please contact your local service
provider:
HomeFree Systems Inc.
Phone: 1-800-606-0661
Outside US call: +927-3-7671900
E-mail:contactusa@homefreesys.com
Web Site: www.homfreesys.com