D and M MPGBR052 WIRELESS LAN MINI PCI ADAPTER User Manual DS MP G BR 05 Ext 2 ver1 6
D&M; Holdings Inc. WIRELESS LAN MINI PCI ADAPTER DS MP G BR 05 Ext 2 ver1 6
D and M >
Manual
MP-G-BR-05, EXT. 2 802.11G 16BIT WIRELESS LAN MINI PCI ADAPTER Data Sheet www.usi.com.tw Sep. 2005 Rev 1.6 Introduction The Mini-PCI Adapter type-III B is a high-speed 54 Mbits/s wireless networking card providing a multimode 802.11 b/g or 11g mode only connectivity for enterprise and home wireless LAN access . The Mini-PCI Card uses direct sequence spread spectrum (DSSS), Orthogonal Frequency Division Multiplexing (OFDM) technology, and implements DBPSK, DQPSK, and CCK, OFDM modulation, as defined in the IEEE® 802.11b, g. This gives a very robust radio channel, which is made even better by the excellent receiver sensitivity and delay spread robustness. In environments with radio interference, the Mini-PCI Card, because of its acknowledgment protocol and its option to be tuned to another frequency channel, continues to run. Features • • Superior echo path management makes it suitable for areas with a large delay spread, for example, warehouses. This reduces the number of cells required and, therefore, reduces the total cost of ownership. • • A firmware-based architecture is capable of supporting the latest industry standards in the security and quality of service (QoS), as the draft 802.11i and 802.11e standards, respectively. • • • The Mini-PCI Card is complemented by drivers and networking tools for various versions of the Windows ® operating system. USI provides extensive technical documentation on integration issues such as antenna design, customizing drivers, and management software. Automatic fallback: 54 Mbit/s, 48 Mbit/s, 36 Mbit/s, 24 Mbit/s, 18 Mbit/s, 12 Mbit/s, 11 Mbit/s, 9 Mbit/s, 6 Mbit/s, 5.5 Mbits/s, 2 Mbits/s, or 1 Mbit/s . Feature with Afterburner technology for this 54g platform, Products with this new technology provide up to 40 percent greater throughput than typical standard 802.11g systems without impacting the performance of neighboring wireless LANs. Low power consumption. Automatic power management to reduce battery use. Easy integration into mobile and hand-held platforms. It’s flexible for design and antenna placement. External antenna diversity. Support AES-CCM, WPA (SSN-TKIP), and WEP (64-bit/128-bit or 152-bit). Corresponding to IEEE 802.11b/gspecification. Interoperable with other IEEE 802.11a/b/gcompliant systems. Conformable to industry-standard MiniPCI Card Type III-B specification. WDS support WHQL pre-test and Wi-Fi pre-test. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b/g Wireless LAN Mini-PCI Adapter EXECUTIVE SUMMARY This document outlines the product requirements for an 802.11g mini PCI adapter 16 Bits– here after referred as “ MP-G-BR-05 Ext2“.RoHS version This product is targeted for first shipments in Q4, 2005 By using Broadcom chipset solution which including; BCM4318 SoC MAC+BB+Transceiver SiGe SE2521A34 for 11g PA and SE2521A60 as alternative Physical Dimension/Packaging The Mini-PCI Card has been designed to conform to the Mini-PCI specification, as defined in Mini-PCI Specification Rev 0.1. All dimensions in this section have a tolerance as permitted in the Mini-PCI Specification. Dimension: 59.8 mm x 44.8 mm x 5.0 mm (actually Max thickness is 3.3mm on metal shield , there is no component on the bottom side of this card) Weight: Less than 25 g Package: Bulk in 200 pcs. Figure 1. Mini-PCI Type III-B dimension Mechanically unique coaxial connectors for two external antennas. Operating Conditions Operating Temperature Operating Humidity Storage Temperature Storage Humidity 0° to 70° Celsius 90% (non-condensing) -10°C to +75°C ambient temperature 95% (non-condensing) All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b/g Wireless LAN Mini-PCI Adapter Voltage and Current The MP-G-BR-05 will comply with the following features and standards Voltage Current Transmit Receive Stand By 3.3 VDC from host (+/-0.2V) 802.11g (Typ.) <450mA <350mA <50mA Wireless Specification The MP-G-BR-05 will comply with the following features and standards: Features Description WLAN Standards IEEE 802 Part 11b/g Antenna Connector Hirose connector supported with diversity 1, 2, 5.5, 11 Mbps for 802.11b Data Rates 6, 9, 12, 18, 24, 36, 48, 54 Mbps for 802.11g and 125Mbps for AfterBunrer Medium Access Protocol CSMA/CA (Collision Avoidance) with ACK RF specification Features Frequency Band Number of Channels Modulation Supported Rates Maximum Receive Level Antenna Description 2412 – 2462 MHz 11 Channels DBPSK, DQPSK, CCK DSSS for 802.11b & g DPSK, QPSK, 16QAM, 64QAM OFDM for 802.11 1, 2, 5.5, 11 Mbps for 802.11b 6, 9, 12, 18, 24, 36, 48, 54 Mbps for 802.11g -20dBm (with PER< 1 0%) for 802.11g External (Hirose U-F-L) Typical Output Power 17 dBm for 11b 15 dBm for 11g Note: Actual output power may vary based on manufacturing process variations 802.11g Receive Sensitivity Data Rates 54 Mbps 11 Mbps 6 Mbps 1 Mbps Receive Sensitivity -68 dBm (typ) -84 dBm (typ.) -85 dBm (typ.) -90 dBm (typ.) All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b/g Wireless LAN Mini-PCI Adapter Note: Actual receive sensitivity for individual products may vary based on manufacturing process and environmental variations Antenna Specifications The Mini-PCI adapter is available in two variants: unique coax connectors with diversity function. On-Board Diversity Switch This variant of the Mini-PCI Card has connectors for two external passive antennas: MAIN and AUX. One of the antennas is used for transmission, and the DSP selects which of the two to use for reception, based on signal strength. The coax connectors for the antennas are mechanically unique, so that no off-the-shelf connector will fit (FCC requirement). Switch electronics for selection between the two antennas for reception of the stronger receive signal is provided onboard. Security At the physical layer, transmissions are encrypted using WEP; three levels of encryption are possible: • 40-bit key plus 24-bit initialization vector • 104-bit key plus 24-bit initialization vector • 128-bit key plus 24-bit initialization vector AES, TKIP, WPA draft 802.11i are supported. Attacks have been made on WEP by exploiting various weaknesses. The Mini-PCI Card implements random setting of the initialization vector and utilizes WEPplus, which prevents initialization vectors that result in weak keys being used. WEPplus is completely compatible with WEP. For those operating systems that support it either natively or with an add-on supplement (i.e, Windows 98, Windows 98SE, Windows ME , Windows 2000, Windows XP, the 802.1x, WPA/TKIP SSN security standard are implemented. This offers port-based network access control, and automatic key distribution. Software/Driver Due to 16-bit architecture is not suitable for current Windows OS (Win98;Win2K;WinXP) , so it only support Linux’s based driver. Driver for WiFi is pre-tested under Ver.3.90.11.0. Performance Table 1. Characteristics at Different Rates The real operating range will be different by measurement environment and condition. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b/g Wireless LAN Mini-PCI Adapter 802.11b/g Data Rates 54 Mbps 11 Mbps 6 Mbps 1 Mbps Operating Distance 70m 370m 330m 550 m Mini-PCI Card Pinout The Mini-PCI Card connects to a host through the Mini-PCI interface bus. The connector pinout is defined in the Mini-PCI Specification . • Support 2 control signals to the host via the Mini-PCI Connector pin 11 for RF On and pin 13 is used as a hardware radio on/off switch. International Channel Frequencies The Mini-PCI Card uses frequencies in the 2.4 GHz to 2.5 GHz ISM band, as defined by IEEE 802.11. The channels available in the regional variants of the Mini-PCI Card are: • FCC: 1 to 11 • ETSI: 1 to 13 • Japan: 1 to 14 Regulatory Body Approvals/Compliance USI will perform pre-test for the following international regulations: approval is a matter for the OEM once the device is integrated into a host platform. Description Country FCC CFR47 Part 15B, Class II 89/336/EEC, ETS 301 489-1&17 (2.4GHz) EN61000-3-2 (Harmonic AC Current emissions) EN55022 Class II, EN50082-1 (Immunity) International CB (IEC 60950) USA Europe FCC CFR47 part 15 C, para 15.247,295,209 EN 300-328 Electromagnetic Compatibility Product safety Radio Regulations Compliance USA Europe Ordering Information USI 802.11g 16Bit miniPCI Adapter Model No. MP-G-BR-05, Ext.2 Specifications are subject to change without notice. IEC is a registered trademark of The Electrotechnical Commission. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. 802.11 b/g Wireless LAN Mini-PCI Adapter IEEE is a registered trademark of The Institute of Electrical and Electronics Engineers, Inc. Intel is a registered trademark of Intel Corporation Microsoft, Windows , and Windows NT are registered trademarks and Windows Me and Windows XP are trademarks of Microsoft Corporation. For Additional information, please contact the following: Universal Scientific Industrial Co., Ltd. Headquarters 141, Lane 351, Taiping Road, Sec. 1 , Tsao-Tuen , Taiwan, Http://www.usi.com.tw Tel: + 886-49-2350876, 2325876 Fax: +886-49-3439561, 2337360,2351093 E-mail:usi@ms.usi.com.tw All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Installation Description (This Installation Manual is not provided to the consumer.) WLAN Module (Model: MP-G-BR-05 Ext.2) shall be installed in a product of D&M Holdings Inc., Denon Brand Company only. When MP-G-BR-05 Ext.2 is installed in the final product, we as OEM shall consider the following points; 1. Since MP-G-BR-05 Ext.2 owns its FCC ID, we shall affix an exterior label on the outside of the final product if the FCC ID is not visible. The exterior label shall use wording such as either “Contains Transmitter Module FCC ID: BV2-MPGBR052/ IC: 6963A-MPGBR052” or “Contains FCC ID: BV2-MPGBR052/ IC: 6963A-MPGBR052”. 2. MP-G-BR-05 Ext.2 complies with requirements of sub-sections 15.203, 15.205, 15.207 and 15.247 in FCC Rules Part 15 and IC Rule of RSS-210/ RSS-Gen. We shall install MP-G-BR-05 Ext.2 in accordance with their requirements. MP-G-BR-05 Ext.2 complies with requirements of the sub-section 2.1091. When installers install MP-G-BR-05 Ext.2 into a product, they shall ensure that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines in accordance with the sub-section 15.247(i) in FCC Rules Part 15 and also IC Rules RSS-102.The WLAN module can be equipped on any product, if the distance between radiator and person’s body keep at least 20cm or more. 3. Attached photos and drawings are an example of location of MP-G-BR-05 Ext.2 on the final product. We do not exhibit this information to end-users or website. Because, users may obtain an idea of modifying this module from the information. 4. It only can be installed to the host that has a regulator (PQ070XZ01ZxH or BAXXDD0WHFP) (or similarly specification regulator). 【FCC/ IC Users Manual Statement】 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles).
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2005:09:22 13:46:06Z Modify Date : 2007:05:09 16:07:46+09:00 Page Count : 7 Creation Date : 2005:09:22 13:46:06Z Author : Daniel Producer : Acrobat PDFWriter 5.0Windows NT ª© Mod Date : 2007:05:09 16:07:46+09:00 Metadata Date : 2007:05:09 16:07:46+09:00 Title : DS_MP-G-BR-05, Ext.2 ver1.6.doc Creator : Daniel Has XFA : NoEXIF Metadata provided by EXIF.tools