DREAMUS IHP100 MP3 Player User Manual users manual a
IRIVER LIMITED MP3 Player users manual a
DREAMUS >
Contents
- 1. users manual a
- 2. users manual b
users manual a
Instruction Manual PORTABLE STORAGE DEVICE & MULTI - CODEC JUKE BOX Model iHP-100 Model iMP-350 Model iHP-100 Thank you for your purchase. Please read this manual carefully before using your new player. http://www.iRiver.com THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICES MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE, RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. Portable Storage Device IHP-100 can be used as the storage device with 10GB capacity. URL : http://www.iRiver.com USB 2.0 is supported IHP-100 is the storage supporting USB 2.0 Interface which maximum transfering speed is 480 MBit/Sec. Provides information on our company, products, and email addresses for support. Multi-Codec Player Supports MP3, WMA and ASF WAV format as multi-Codec player. WAV file only support 44.1KHz / 16 Bit. Unique feature of "Firmware (system software) Upgrade" is available for download on our site. The Firmware Upgrade provides new features as well as enhancements to current features. Firmware Upgrade Provides the latest updated features via firmware upgrade. New formats such as OGG, AAC, MP3 Pro and etc can be supported in the future with a simple upgrade method. Player features such as add on, modification, and continuous improvement of the player are always provided. Register your iRiver product online so that our Customer Service is enabled to provide support as efficiently as possible. Contents described in this manual may be changed to improve or any specification without notice. Graphic LCD supporting Multiple Languages A total of 38 languages of 37 countries are supported. FM Tuner Auto scanning and frequency memory function make it easy for you to enjoy listening to the FM Radio. This player supports 6 Equalizer Patterns. Normal, Rock, Jazz, Classic, Ultra Bass, User EQ Easy Navigation The simple navigation with tree configulation makes it easy to find or save any song. Total 1000 folders and 5000 tracks within the player can be recognized. Graphic User Interface Menu Support FM recording, Voice recording and recording(Line-In/Optical In) from an external audio equipment is supported. When voice recording, recording level is automatically controlled at voice recording mode. Line-Out / Optical-Out function is supported iRiver Limited does not assume any responsibility for errors or omissions in this document or make any commitment to update the information contained herein. iRiver is a registered trademark of iRiver Limited in the Republic of Korea and/or other countries and is used under license. All other brand and product names are trademarks of their respective companies or organization. All other product names may be trademarks of the companies with which they are associated. 1999~2003 iRiver Limited, All right reserved Microsoft Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and /or other countries. 1. Locating the Controls Front View, Side View....................................................... 5 Up/ Down Side, LCD Window........................................... 6 Remote Control................................................................. 7 FRONT VIEW LCD Window 2. Getting started Using AC POWER ADAPTER.......................................... Software Installation.......................................................... Connecting the iHP-100 to the Host PC........................... Installing the iHP-100 Device Driver................................. Using as a Portable Storage............................................. Disconnecting the iHP-100 to the Host PC....................... Listening to Music............................................................. Basic Operation................................................................ 10 11 12 13 14~15 16~19 3. Useful Features Navigation Mode / Menu / Mode....................................... Playback Mode................................................................. Navigation......................................................................... Upgrading DB................................................................... Adding DB......................................................................... Operating the FM Tuner.................................................... Recording.......................................................................... Playback Mode................................................................. EQ..................................................................................... Menu................................................................................. Firmware Upgrade............................................................ 19 20 21~23 24 25 26~28 29~32 33 34 36~44 45 4. Additional Information Reference......................................................................... Precautions...................................................................... Trouble Shooting............................................................... Accessories....................................................................... Product Specifications...................................................... Regulatory information...................................................... 46 47 48 49 50 51 Charge Operating Indicator HDD Operating Indicator Jog Handle for Multi Function Control SIDE VIEW Mic Power ON/ / FM HDD(Play / Pause) (Stop)/ Power OFF Rec Button A-B(Interval Repeat) / MODE HOLD Remote Control UP/ DOWN SIDE (STOP) / Power OFF LINE INPUT (Optical / Analogue) Power ON / FM HDD (PLAY / PAUSE) LINE OUTPUT REMOTE CONTROL/ (Optical / Analogue) EARPHONES Jog Handle for Multi Function Control DC IN 5 V USB Connection Port BITRATE LCD Window THE ORDER OF SONGS PLAYBACK MODE HOLD REC NAVI/MENU SOURCE /TYPE BATTERY INDICATOR FOLDER NAME ARTIST NAME TITLE NAME Level Meter Playback Information PLAY TIME HOLD FILE FORMAT BIT RATE EQ A-B/MODE VOLUME - VOLUME + SAMPLE RATE Using AC POWER ADAPTER Use only the AC Power Adapter supplied with the player. Connect the adapter to the 5V DC jack on the player and into an AC outlet. To install “Program” Windows 2000 and Windows XP have the program to support USB 2.0 Storage Device, and you can use this player without any program installation. But install iHP manager to use DB function. And install this program to use this player as portable storage at Windows 98SE, ME O/S. Insert the Installation CD into the CD-ROM drive. The following screen appears after inserting the CD. Click Yes” to install the instllation program. Click “NEXT” after writing user’s information. Click “Next” after selecting item to be installed. Click “Next”. Installation is progressing. Recharging Method Rechargeable function can automatically be activated while the AC adapter is connected to the player. When fully charged, charge operating indicator is extinguished. Charging : Approx. 3 hours (At full discharge) Discharging (Playback time) : Approx. 16 hours (At full charge) Click “Finish”. The installation is completed. To install the iHP-100 Device Driver This processing must be done after installing the iHP-100 Manager Program. If the player is recognized on the host PC, Add New Hardware Wizard is activated. Click “Next”. Click “Next” after selecting “Driver Search” option. Click “Next” after selecting the folder saved the “iRiHP. inf” Click “OK” after selecting the folder installed the “iRiHP. inf” file (C:\ProgramFiles\iRiver\iHP100\ drivers) Click “Next” Click “Next” To connect the iHP-100 to the Host PC Click to turn on the player. Connecting the USB cable between the player and Host PC. Type “A” Type “A” Type “B” USB port on the PC USB cable USB port on the iHP Series Type “B” Check whether the icon on the window was made. Only a icon may be made according to the O/S. If the host PC using Windows98 etc. do not recognize the player, install iHP-100 Device Driver to the host PC (Refer to page 12). Confirm whether new driver is added on the explorer. Click “Finish” Completed the installation of “Device Driver”. The initial volume name is “iHP-100”. 10 11 To use as a portable storage To disconnect the player from the Host PC If the player is not connected to the host PC, connect it to the host PC. (Refer to page 10) Check the icon of the player on the PC window and confirm whether the player is added as a new driver on the explorer. Click anyone of 2 icons. To copy from the PC to the player Drag and Drop to copy folders or files of the PC to the driver of the player. Click “Stop iRiver iHP-100-Driver(X)” or “Safely Remove TOSHIBA MK1 3GAL USB Disk Drive(X:)”. (X : Disc Driver name) Click “Delete” after selecting the files or folders to delete on the iHP-100 and Click “Yes” to delete. Click OK after confirming the “Safe To Remove Hardware” massage. You can use all functions using explorer and hard driver of the player as well as copying / deleting as like HDD driver. Disconnect the USB cable between the iHP-100 and host PC. Note Use AC Adapter when you use the player with connection to the host PC for a long time. If the battery’s shortage occurs during tranfering datas, Data transfering may be stopped. 12 13 Connect the earphones and remte control as shown below. Put the HOLD switch to “OFF”. To play / Pause Press the PLAY/STOP button to turn on the player. Press it again to play. To select music : To select previous music : To select next music To fast forward To stop To fast reverse To play next track To turn off the player To play previous track To adjust the volume To increase volume To decrease volume NOTE - When "Hold" is ON, the buttons on the player will not function. - In case of stop status of the player or standby status of Voice recording, the player automatically turns off according to the setting of “STOP POWER OFF” on the MENU.(Refer to page 41) 14 File Format displayed as below MP3 WMA ASF WAV 15 Basic Operation To adjust the volume Press + on volume button to increase volume and press – on button to decrease volume. File playback FM receiving To Record Selecting FM Mode when listening FM : (Refer to page 26) [Record standby] [To start recording] [To select source to record] To activate Navigation 1. To increase volume. 2. To select the previous music for Audio files or station for FM. 3. To increase volume. 4. To select the next music for Audio files or [To select Bitrate Type] [To select File Type] station for FM. 5. To select NAVI/MENU function. To activate Menu 6. Internal Microphone 7. To change record standby mode or start recording. 8. To start or pause playback to change FM 9. To stop playback or recording or turn off. 10. To select EQ mode, A-B repeat or memory stations for FM automatically. EQ : NORMAL ROCK JAZZ CLASSIC U. BASS User EQ 11. HOLD : the buttons on the player will not function or not. [To stop recording / Standby for recording] NAVIGATION Press NAVI/MENU button and find the desired track by pressing the VOL + or VOL – button, or , NAVI/MENU button. There are two methods using ID3 Tag and PATH/NAME of File on NAVIGATION. Refer to page 21 for details. 16 17 The remote control operates every function using 5 buttons. Basic Operation Function Volume Control: Slide jog lever to the right to increase volume or to the left to decrease volume. Changing Mode : STOP (Refer to page 28) HDD FM Changing : PLAY / PAUSE NAVIGATION Main unit and Remote control both locked. Only Main unit is locked. Only Remote control is locked. Press the Navi/Menu jog lever with a short click and find the desired track by or . To play the track, press Navi/Menu with a short click. pressing To move to the upper folder, press with a short click. In case there is not the upper folder, exit NAVIGATION function. Basic Operation Function To listen to the next track, please push the jog switch to the right. Playback and Pause Stop and Power Off Navigation Operation Menu Operation 18 MENU Long press of NAVI/MENU will execute menu function. Scrolling between menus : Press and Select Function: press Navi/Menu button. Exit : Press with a short click. MODE While Audio File is playing, press A-B/MODE button with a long click to activate selected modes, such as Repeat and Shuffle. 19 Interval Repeat Play selected interval repeatedly while playing. Press A-B button once to select the beginning Point. It is useful when fast-searching your favorite file of files listed on the player by using ID3 Tag information and file name. In case DB file (irivnavi.idb) was damaged or deleted, it is operated as a music searching function by using File Tree information. 1. Navigation using File Tree Press the NAVI/MENU handle to display the list of musics. And the current playing music is displayed. Press A-B button again to select the ending Point. Push the NAVI/MENU handle toward play. or to select a music or folder to A-B interval will be repeated. Press the NAVI/MENU handle to play the selected music or to display the contents of the selected folder. If you select a folder, start playback after selecting a music to play by repeating 2~3 steps. Push the NAVI/MENU handle toward previous menu. 20 to go the upper folder or the 21 2. Navigation using Music Information It is useful when fast-searching your favorite file of files listed on the player by using ID3 Tag information and file name. Press the NAVI/MENU handle toward condition. or to select searching In case DB file (irivnavi.idb) was damaged or deleted, it is operated as a music searching function by using File Tree information. Press the NAVI/MENU button. The function selection graphic displays on the LCD. Push the NAVI/MENU handle toward function. To search by artist s name To search by album’s name or To search by genre menu Press the NAVI/MENU button to display detail picture of the selected searching function. to select the searching To search by title name If the selected item has not any detail condition, the selected music starts playback immediately. To search by files & folders Press the NAVI/MENU button to display detail picture of the selected searching function. When you select “Select All”, all music fit to the selected condition are played repeatedly and is displayed on the display. To cancel List Repeat Mode, press STOP button at the stop mode. Repeat 4 ~ 5 steps to search another file. Push I 22 to go back the previous step. 23 24 To update DB To add DB When DB file (irivnavi.idb) was damaged or deleted by your mistake, you can not use NAVIGATION by using ID3 Tag information. You can create or restore DB file by using the host PC. When DB file (irivnavi.idb) was damaged or deleted by your mistake, you can not use NAVIGATION by using ID3 Tag information. You can create or restore DB file by using the host PC. Connect the player to the host PC. (Refer to “Connecting the iHP-100 to the Host PC”, page 10) After activating the explorer on the PC, select iHP-100 driver. Connect the player to the host PC. (Refer to “Connecting the iHP-100 to the Host PC”, page 10) After activating the explorer on the PC, select iHP-100 driver. Click the right button of mouse. Select “DB File update” to activate DB File update. Click the right button of mouse after selecting MP3 files or Folders to add to DB. Select “Add Music(s) to DB” to activate this function. Click “OK”. After disconnecting the player from the host PC, you can use the Navigation function using ID3 Tag. (Refer to “Disconnecting the player from the Host PC”, page 13.) ID3 Tag information of the selected files are added to DB. In case DB file is not, new DB file(iRivNavi.iDB) is created. After disconnecting the player from the host PC, you can search the added musics by using ID3 Tag. (Refer to “Disconnecting the player from the Host PC”, page 13.) 25
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Modify Date : 2003:04:25 10:54:01-04:00 Create Date : 2003:04:25 10:53:47-04:00 Producer : Acrobat Distiller 4.0 for Macintosh Page Count : 14EXIF Metadata provided by EXIF.tools