ELITEGROUP COMPUTER SYSTEMS BR45IIX6230 Notebook Computer User Manual BR45II7 english
ELITEGROUP COMPUTER SYSTEMS CO., LTD Notebook Computer BR45II7 english
user manual
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This equipment is without ad hoc mode function. Preface Copyright 2011 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer. Limitation of Liability While reasonable efforts have been made to ensure the accuracy of this manual, the manufacturer and distributor assume no liability resulting from errors or omissions in this manual, or from the use of the information contained herein. Notice: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Shielded interface cables and a non-shielded AC power cord must be used in order to comply with emission limits. This equipment is to be used with power supply: 65W There is no internal power supply. Table of Content BEFORE YOU START ...............................................................................2 LET YOUR COMPUTER ACCLIMATE ITSELF ............................................12 HEAT, COLD, HUMIDITY, AND GLARE ..................................................13 SUITABLE PLACE TO WORK .................................................................13 INTRODUCTION .....................................................................................15 FRONT VIEW .....................................................................................16 LEFT VIEWS ......................................................................................18 RIGHT VIEW ......................................................................................19 BOTTOM VIEW ...................................................................................20 GETTING STARTED ...............................................................................22 CONNECTING THE AC ADAPTER .........................................................22 TO INSTALL THE BATTERY PACK:........................................................24 TO REMOVE THE BATTERY PACK:.......................................................25 USING THE NOTEBOOK COMPUTER ........................................................27 LCD CARE ........................................................................................27 EXTERNAL CRT DISPLAY ...................................................................27 TOUCHPAD PRECAUTIONS .................................................................29 DATA STORAGE AND RETRIEVAL ........................................................30 THE BATTERY POWER SYSTEM ..........................................................30 PREPARING THE BATTERY PACK FOR USE (BATTERY CALIBRATION) ....31 AUTOMATIC BATTERY PACK CHARGING FUNCTION ..............................31 BATTERY STATUS ..............................................................................32 BATTERY LOW W ARNING ...................................................................32 HELP W INDOWS ................................................................................33 DESKTOP ..........................................................................................34 MAIN SETUP......................................................................................43 INFO SETUP ......................................................................................43 ADVANCED ........................................................................................44 SECURITY .........................................................................................44 TPM STATE ......................................................................................45 BOOT SETUP.....................................................................................45 EXIT SETUP ......................................................................................46 ADVANCED PAGE ..............................................................................52 OPTIMIZING W INDOWS SETTING:........................................................59 ii HARD DISK MENU..............................................................................61 CPU.................................................................................................62 RAM: ...............................................................................................62 W ARNING:.........................................................................................63 TROUBLESHOOTING ..............................................................................65 SPECIFICATION .....................................................................................68 iii 1 Before you Start Conventions of This Manual Use this manual will help you get the most from your notebook computer. If you are an experienced user of computers and/or Microsoft’s Windows operating systems, you might find it useful to read the Quick Start Guide that comes along with your accessories. If you are a less experienced user, you should go through the manual carefully before using your system. Whether or not you are an experienced user, you should consult the Troubleshooting Chapter if you encounter any problems with your notebook. Safety Precautions This section is designed to assist you in identifying potentially unsafe conditions while working with this product. Required safety features have been installed in the computer to protect you from injury. However, you should use good judgment to identify potential safety hazards: Please read these safety instructions carefully. 1. Please keep this User's Manual for later reference. 2. Please disconnect this equipment from AC outlet before cleaning. Don't use liquid or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning. 3. For pluggable equipment, that the socket-outlet shall be installed near the equipment and shall be easily accessible. 4. Please keep this equipment from humidity. 5. Lay this equipment on a reliable surface when installed. A drop or fall could cause injury. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Make sure to use the right voltage for the power source when connecting the equipment to the power outlet. Place the power cord in such a way that people can not step on it. Do not place anything on top of the power cord. All cautions and warnings on the equipment should be noted. If the equipment is not used for a long time, disconnect the equipment from the main power outlet to avoid being damaged by transient overvoltage. Never pour any liquid into the opening, this could cause fire or electrical shock. Never open the equipment. For safety reasons, the equipment should only be opened by a qualified service personnel. If on the following situation arises, get the equipment checked by a service personnel: a. The Power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment has not worked well or you cannot get it work according to the user's manual. e. The equipment has dropped and damaged. f. If the equipment has obvious signs of breakage. Do not leave this equipment in an environment unconditioned, storage temperature above 60°C (140°f), it may damage the equipment. The unit can be operated at an ambient temperature of max. 5°C ~ 35°C. The sound pressure level of the operator's position according to IEC 704-1: 1982 is equal or less than 70 dB(A). Power Cord Requirements The power cord set used with the AC adaptor must meet the requirements of the country where you use the AC adaptor, whether it is 100-240 Vac. The following information explains the requirements for power cord set selection. The cord set must be approved by the country in which it is used. The appliance coupler must have a configuration for mating with a CEE7/EN60320/IEC 320/NEMA/ JIS C 8303 appliance inlet. A. For U.S. and Canada: The cord set must be UL Listed and CSA Certified. B. C. The minimum specifications for the flexible cord are No. 18 AWG, (2) Type SPT-2, and (3) 2conductor. For Japan: All components of the cord set must bear a “PSE” mark and in accordance with the Japanese Dentori Law. The minimum specifications for the flexible cord are .75m ㎡ conductors, (2) Type VCTR or VCTFK, and (3) 2-conductor. The cord set must have minimum rated current capacity of 7 A. The attachment plug must be a two-pole, grounded type with a Japanese Industrial Standard C8303 (15 A, 125 VAC) configuration. For Other Countries: The cord set fittings must bear the certification mark of the agency responsible for evaluation in a specific country. The flexible cord must be of a HAR (harmonized) type H03VVH2-F. The cord set must have a current capacity of a least 2.5 Amperes and voltage rating of 125 or 250 Vac. MODEL BR45IIX (x=0~9) IS DESIGNED TO USE WITH THE FLLOWING AC ADAPTER MODEL ONLY 65W ADP: Huntkey type: HKA06519034-8C/ HKA06519034-6C Delta type: ADP-65JH AB/ ADP-65JH BB Lite-On type: PA-1650-65/ PA-1650-68 17. When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons. These precautions include the following: Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special instructions. 18. Do not use the AC adapter near open water or other liquids. Never spill liquid into the AC adapter. 19. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power. 20. The input receptacle is used as the main disconnecting device. This part is hot. Be careful. Diese Flachewird sehr heiss. When you see this symbol, be careful as this spot may be very hot. 21. Laser Warning: Laser Class I Product Caution - Invisible laser radiation when open avoid exposure to beam. The optical drive used with this computer is certified as a Class1 laser device according to the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard and International Standards IEC 60825-1 (EN60825-1). The device is not considered harmful, but the following precautions are recommended: Do not open the unit. Avoid direct exposure to the laser beam. If the unit requires service, contact an authorized service center. Ensure proper use by reading and following the instructions carefully. Do not attempt to make any adjustment of the unit. Class 1 Laser Product Appareil A Laser De Classe 1 Laserschutzklasse 1 Produkt Do not attempt to disassemble the cabinet containing the laser. The laser beam used in this product is harmful to the eyes. The use of optical instruments, such as magnifying lenses, with this product increase the potential hazard to your eyes. For your safety, have this equipment serviced only by an authorized service provider. Wichtige Sicherheitshinweise 1. 2. 3. Bitte lesen Sie diese Hinweis sorgfältig durch. Heben Sie dirse Anleitung für den späteren Gebrauch auf. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Versenden Sie Keine Flüssig- oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung. 4. Die Netzanschluβsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Beschädigungen hervorrufen. 7. Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte. 8. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch nichts auf der Leitun abgestellt werden. 9. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten. 10. Wird das Gerät üeinen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden. 11. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeien in das Gerät gelangen. Dies könne einen Brand bzw. Elektrischen Schlag auslösen. 12. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden. 13. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu Überprüfung.: a. Netzlabel oder Netzstecker sind beschädigt. b. Flüssigkeit ist in das Gerät eingedrungen. c. Das Gerät war Feuchtigkeit ausgesetzt. d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt. f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist. 14. VORSICHT: Explosiongsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. 15. Dieses Schaltnetzteil kann bis zu einer Außentemperatur von maximal 5ºC 35ºC. 16. Die Ausgangswerte dürfen nicht die auf dem Label angegebenen Werte überschreiten. Anforderungen an das Stromkabel Das Kabel-Set, das an das Netzteil angeschlossen wird, muss den Anforderungen des Landes, in dem Sie das Netzteil einsetzen, genügen, je nachdem, ob die Netzspannung 100-240V Wechselspannung beträgt. Das Kabel-Set muss für das Land, in dem es eingesetzt wird, zugelassen sein. Der Gerätestecker des Kabels muss in eine CEE7/EN60320/IEC 320/NEMA/ JIS C 8303 Buchse passen. A. Für die USA und Kanada: Das Kabel-Set muss UL-gelistet und CSA zertifiziert sein. Die Minimalanforderungen für das Kabel entsprechen No. 18 AWG. (2) Type SPT-2, und (3) 2-conductor. B. Für Japan: Alle Teile des Kabel-Sets müssen entsprechend dem japanischen Dentori Law mit einem „PSE“ markiert sein C. Die Minimalanforderungen für das Kabel sind .75m ㎡ Leiter. (2) Type VCTF oder VCTFK, und (3) 2-conductor. Der Kabelsatz muss mindestens für eine Stromstärke von 7A geeignet sein. Der Wandstecker muss ein zweipoliger geerdeter Steckertyp gemäß dem Japanese Industrial Standard C8303 (15A, 125 VAC) sein. Für andere Länder: Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel derjenigen Stelle, die in dem jeweiligen Land für die Sicherheitsprüfung zuständig ist, tragen. Das Kabel muss vom HAR (harmonisierten) Typ H03VVH2-F sein. Das Kabel-Set muss eine Stromkapazität von mindestens 2,5 Ampere haben und Spannungen von 125 oder 250 V Wechselstrom gestatten. Mit dem BR45IIX (x=0~9) muss ein ACAdapter folgenden Modells verwendet werden 65W ADP: Huntkey type: HKA06519034-8C/ HKA06519034-6C Delta type: ADP-65JH AB/ ADP-65JH BB Lite-On type: PA-1650-65/ PA-1650-68 17. Bei der Benutzung Ihres Telefongerätes sollten Sie immer die grundlegenden Sicherheitsmaßnahmen beachten, um das Risiko von Feuer, Stromschlägen und Verletzungen zu minimieren. Zu beachten sind u.a. folgende Punkte: Benutzen Sie das Gerät nicht in der Nähe von Wasser, wie zum Beispiel Badewanne, Waschbecken, Spülbecken, Waschbottich, in feuchten Kellerräumen oder in der Nähe von Schwimmbecken. Benutzen Sie kein Telefon (ausgenommen schnurlose Modelle) während eines Gewitters. Es besteht das geringe Restrisiko eines Blitzschlages. Benutzen Sie das Telefon nicht um ein Gasleck zu melden, falls es sich in der Nähe des Lecks befindet. Verwenden Sie nur die in diesem Benutzerhandbuch angegebenen Stromkabel und Batterien. Werfen Sie die Batterien nicht ins Feuer, sie könnten explodieren. Informieren Sie sich über die örtlichen Bestimmungen bezüglich der Entsorgung. 18. Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser oder anderen Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das Netzteil. 19. Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird. Ersetzen Sie den Akku nur durch einen Akku gleichen oder äquivalenten Typs, der vom Hersteller empfohlen wird. Entsorgen Sie Akkus entsprechend den Anweisungen des Herstellers. Entfernen Sie den Akku auf keinen Fall bei eingeschaltetem notebook, da hierdurch Daten verloren gehen könnten. 20. Der Netzeingabeanschluss dient als Hauptschalter des Geräts. Mesures de sécurité Cette section a pour but de vous aider à identifier des conditions potentiellement dangereuses d'utilisation de ce matériel. Les dispositifs de sécurité nécessaires ont été installés sur l'ordinateur pour vous protéger contre d'éventuelles blessures. Cependant, vous devez utilisez votre propre discernement pour identifier les dangers possibles: 1. Veuillez lire ces instructions attentivement. 2. Veuillez conserver le présent guide d'utilisation pour référence ultérieure. 3. Veuillez débrancher ce matériel de l'alimentation secteur avant nettoyage. N'utilisez pas de détergent liquide ou vaporisé pour le nettoyage. Utilisez un tissu humidifié. 4. En ce qui concerne le matériel connecté, veillez à ce que la prise d'alimentation soit située à proximité du matériel et facilement accessible. 5. Veuillez conserver ce matériel à l'abri de l'humidité. 6. Installez ce matériel sur une surface stable. Une chute peut provoquer des blessures. 7. Vérifiez que vous utilisez une tension d'alimentation correcte avant de brancher l'adaptateur secteur. 8. Placez le cordon d'alimentation de manière à ce que personne ne puisse marcher dessus. Ne placez aucun objet sur le cordon d'alimentation. 9. Tous les avis et avertissements concernant ce matériel doivent être respectés. 10. Si le matériel n'est pas utilisé pendant une longue période, débranchez-le de l'alimentation secteur afin d'éviter qu'il puisse être endommagé par d'éventuelles surtensions. 11. Ne jamais verser de liquide dans les ouvertures, cela pourrait provoquer un incendie ou un choc électrique. 12. N'ouvrez jamais le boîtier. Pour des raisons de sécurité, le matériel ne doit être ouvert que par un technicien spécialisé. 13. Si l'une des situations suivantes est rencontrée, faites vérifier le matériel par un technicien de maintenance : A. Le cordon d'alimentation est endommagé. B. Du liquide a pénétré dans l'appareil. C. Le matériel a été exposé à l'humidité. D. Le matériel ne fonctionne pas correctement, ou vous ne pouvez pas le faire fonctionner comme indiqué dans le guide d'utilisation. E. Le matériel est tombé et il est abîmé. F. Le matériel présente des signes évidents de rupture. 14. Ne laissez pas ce matériel dans un environnement non contrôlé. Des températures de plus de 60° Celsius (140° F) peuvent endommager le matériel. 15. Le système peut être utilisé dans une température ambiante maximale de 5°C ~ 35°C. 16. Le niveau sonore au niveau de l'utilisateur, selon les termes de la norme IEC 704-1: 1982 est inférieur ou égal à 70 dB(A). 17. Conditions nécessaires pour le cordon d'alimentation Le cordon d'alimentation utilisé avec l'adaptateur secteur doit respecter les conditions fixées pour le pays dans lequel vous utilisez l'adaptateur secteur, qu'il s'agisse d'un courant alternatif 100-240 volts. Vous trouverez ci-dessous les informations concernant les exigences appliquées au jeu de cordon d'alimentation. Le jeu de cordon doit être homologué pour le pays dans lequel il est utilisé. Le coupleur du matériel doit être compatible avec une prise de type CEE7/EN60320/IEC 320/NEMA/ JIS C 8303. A. Pour les États-Unis et le Canada : Le jeu de cordon doit être énuméré dans la liste UL et certifié CSA. 10 Les caractéristiques minimales pour le cordon flexible sont No. 18 AWG, (2) Conducteur du type SPT-2, et (3) 2. B. Pour le Japon : Tous les éléments du jeu de cordon doivent comporter le numéro d'enregistrement selon la loi japonaise Dentori. Les caractéristiques minimales pour le cordon flexible sont des conducteurs de type 0.75mm², (2) Conducteur du type VCTF ou VCTFK, et (3) 2. Le cordon doit avoir une capacité de courant nominal minimum de 7A La fiche de branchement doit être du type deux pôles et mise à la terre avec une configuration de standard industriel japonais C8303 (15A, 125 VAC) C. Pour les autres pays : Les raccords du jeu de cordon doivent porter la marque de l'agence responsable de l'évaluation dans un pays déterminé. Le cordon flexible doit être de type HAR (harmonisé) H03VVH2-F. Le jeu de cordon doit avoir une capacité d'au moins 2,5 et accepter une tension de 125 ou 250 volts. ATTENTION : Le modèle BR45IIX (x=0~9)est conçu pour être utilisé uniquement avec le modèle d'adaptateur CA suivant Huntkey type: HKA06519034-8C/ HKA06519034-6C Delta type: ADP-65JH AB/ ADP-65JH BB Lite-On type: PA-1650-65/ PA-1650-68 18. Lors de l'utilisation de votre matériel téléphonique, des mesures de précaution élémentaires doivent être respectées afin de minimiser les risques de feu, de choc électrique et de blessure. Ces mesures sont énumérées ci-dessous : N'utilisez pas ce matériel à proximité de l'eau, comme par exemple près d'une baignoire, d'un lavabo, d'un bac à laver, dans un sous-sol humide ou près d'une piscine. Évitez d'utiliser le téléphone (autre qu'un téléphone portable) pendant un orage. Il peut exister un risque de choc électrique. 11 N'utilisez pas le téléphone pour signaler une fuite de gaz à proximité de la fuite. Utilisez uniquement le cordon d’alimentation et les batteries spécifiés dans ce manuel. Ne jetez pas les batteries au feu. Elles pourraient exploser. Reportezvous à la règlementation locale pour d'éventuelles instructions particulières. 19. N'utilisez pas l'adaptateur secteur à proximité d'une étendue d'eau ou d'autre liquide. Ne versez pas de liquide dans l'adaptateur secteur. 20. Avertissement relatif aux produits Laser de classe I : Des radiations invisibles sont émises par le Laser. Evitez de vous exposer à ces radiations lorsque le tiroir est ouvert. 21. Risque d’explosion si la batterie est remplacée d’une manière incorrecte. Remplacez uniquement avec une batterie de même type ou de type équivalent recommandée par le constructeur. Débarrassez-vous des batteries usagées en accord avec les instructions du constructeur. Ne jamais retirer le bloc de batteries lorsque l’alimentation est en marche car cela risque de provoquer une perte de données liée à la perte d’alimentation. Things you must remember before working on your computer Let your computer acclimate itself Your notebook can easily stand temperature extremes but it doesn’t like rapid changes in temperature, like going from the cold outdoors to a warm office. Rapid changes in temperature can cause water droplets to condense inside your case, threatening to damage the electronic parts inside. After receiving your notebook when it’s hot or cold outside, try not to power up the computer immediately, let the computer adjust to the room temperature gradually at least for three to four hours. If your system arrives in cold weather, do not apply power to the computer or monitor until they have been allowed to come to room temperature. 12 Heat, Cold, Humidity, and Glare Find a suitable place for your computer that’s not too hot, too cold, too dark, or too bright. Glare can make it hard to read the screen. Try to avoid the computer components from being destroyed if it is overheated, so try to allow plenty of room for air to circulate around the case. Do not block the ventilation opening. Do not place your computer in direct sunlight. Suitable place to work Your computer will run well wherever you’re comfortable but extreme temperature and humidity can be challenging to your system’s parts. There are some things you can tolerate that the computer can’t – things like static electricity, dust, water, steam and oil. In case you decide to pull over for roadside computing, try to choose a clean, comfortable work area for your system. A lithium-ion battery pack will be available when you are traveling. If you are running your system for the first time on battery power, remove the battery from the package, install it into the system and recharge the battery to fully prepare for service. 13 14 Introduction Please use the adapter recommended in this manual. Preparing your Computer Install the battery pack Connecting the AC adapter Opening the display panel Turning on your computer 15 Knowing your Computer With the LCD screen open, you will see several features important for operating your notebook computer. To avoid damage to the display panel: 1. Try not to slam the display upon closing it. 2. Try not to place any object on top when it is closed or open. 3. Be sure the system is turned off or in suspend mode before you close the display panel. Front View Picture is only for reference Internal Microphone Camera (Optional) 16 For best system performance, image is compressed when using the Crazy Talk Camsuite PRO's preview function. Photographs taken with 'snapshot' retain its original quality. LCD Display This LCD panel can only support up to a maximum opening of 125-130 degrees, please do not push it forcibly. Power/Suspend Button Press for 1~1.5 seconds to turn on the system. Press and hold for at least 4 seconds to turn off the system. Press the power / suspend button again to return from the suspend mode. Keyboard The keyboard differs for each territory Touchpad Touchpad Buttons 6-in-1 Card Reader SD/SDHC/SDXC (High speed mode)/MMC/MS/MS-Pro LED Indicator Power ON: Blue RF On: Blue HDD R/W: Blinking Blue Battery LED status Charging: Blinking Blue Full: Blue 17 Battery Low (<6%): Blinking Red Left Views DC In Ethernet / LAN Port When using a LAN, please use an EMI Shielding Cable to minimize an interference when transmitting CRT Port HDMI Port USB 2.0 Ports or 3.0 Ports (Optional) This system provides two USB 2.0 or two USB 3.0 (optional) chargeable ports. 18 Right View USB 2.0 Port Stereo Headphone Jack Microphone/Audio Line-in Jack Optical Drive Kensington Lock 19 Bottom View Battery Lock Battery Compartment Battery Release Latch 20 21 Getting Started Connecting to a Power Source Connecting the AC Adapter A universal AC adapter is provided to supply your computer with power and also charge the computer’s battery pack. The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country. To connect the computer to an external power source: Do not use inferior extension cords as this may result in damage to your notebook. The notebook comes with its own AC adapter. Do not use a different adapter to power the computer and other electrical devices. 22 Whenever possible, keep the AC adapter plugged into the notebook and an electrical outlet to recharge the battery. Never turn off or reset your notebook while the hard disk is in use status icon is lit; doing so can result in loss or destruction of your data. Always wait at least 5 seconds after turning off your notebook before turning it back on; turning the power on and off in rapid succession can damage the notebook’s electrical circuitry. Turning On Your Notebook Computer Hold the button down for a second or two and release. The PowerOn Self Test (POST) runs automatically. After the POST is completed, the computer reads the operating system from the hard disk drive into computer memory (this is commonly referred to as “booting” a computer). If your OS (Operating System such as Windows Vista…. Etc.) is installed, it should start automatically. To turn the notebook off, save your work and close all open applications. Emergency shutdown: Turn off system while pressing power button over 4 seconds in after-POST stage (Power On Self Test). Operating on Battery Power Your computer comes with a rechargeable battery pack that lets you operate the computer without an external power source. When the battery pack is fully charged, you can operate the computer under the following conditions: The battery pack initially has a full charge. No peripheral devices are installed. The disk/DVD-ROM drives run no more than 10% of the time Only use batteries that are approved by an authorized dealer. All batteries are not the same and therefore should not be treated as such. Using the wrong battery could cause serious damage to your computer and yourself through toxic emissions. Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent 23 type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions or local laws. Explisionsgefahr bei unsachgernazen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des Herstellers. Installing and Removing the Battery Pack To Install the Battery Pack: 24 To Remove the Battery Pack: Charging the Battery Pack The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source. It is a good idea to occasionally discharge the battery pack fully to preserve its operating performance. 25 26 Using the Notebook Computer Adjusting the LCD Screen Display The LCD screen display can be adjusted by the following key combinations. Fn + F4 Changes Display Mode: LCD-only, CRT/HDMI-only and simultaneous LCD&CRT/HDMI. Fn + F7 Decrease the brightness level. Fn + F8 Increase the brightness level. LCD Care LCD screens are delicate devices that need careful handling. Please pay attention to the following precautions: When you are not using the computer, keep the LCD screen closed to protect it from dust. If you need to clean your LCD screen, use a soft tissue to gently wipe the LCD surface. Do not put your fingers or sharp objects directly on the surface and never spray cleaner directly onto the display. Do not press on, or store any objects on the cover when it is closed. Doing so may cause the LCD to break. External CRT Display You can hook up an external monitor through the 15-pin CRT connector. LCD only CRT/HDMI only Simultaneous LCD&CRT/HDMI 27 You can switch between these display configurations by pressing the key combination [Fn] + [F4]. The Notebook’s Hot Key Controls Fn + ESC Enable/Disable Bluetooth Fn + F1 Enters Suspend Mode. Fn + F2 Enable/Disable Silent mode (power management) Fn + F3 Mute On/Off. Fn + F4 Changes Display Mode: LCD-only, CRT/HDMI-only and simultaneous LCD&CRT/HDMI Fn + F5 Decrease the speaker volume. Fn + F6 Increase the speaker volume. Fn + F7 Decrease the brightness level. Fn + F8 Increase the brightness level. Fn + F9 Enable/Disable Touchpad Fn + F10 Enable/Disable WLAN Fn + F11 Enable/Disable the CCD camera A revolutionary solution for architectural lighting, where maximum light intensity is required. Press this button will increase or decrease the light intensity of your screen display. 28 The TouchPad The touchpad is a rectangular electronic panel located just below your keyboard. You can use the static-sensitive panel of the touchpad and slit it to move the cursor. You can use the buttons below the touchpad as left and right mouse buttons. TouchPad Precautions The TouchPad is a pressure sensitive device. Please take note of the following precautions. Make sure the TouchPad does not come into contact with dirt, liquids or grease. Do not touch the TouchPad if your fingers are dirty. Do not rest heavy objects on the TouchPad or the TouchPad buttons. You can use the TouchPad with Microsoft Windows as well as non-Windows applications. 29 Connecting an External Tracking Devices The system will only enable you to use one tracking device whether it is an internal or external tracking device. Data Storage and Retrieval Data storage and retrieval are two of the most fundamental tasks you will perform when working with your computer. The Notebook is equipped with a hard disk drive (HDD). The HDD is removable allowing for easy upgrades. Power Saving Modes This section contains information on the notebook’s power system, including the AC Adapter, the battery system, recharging the battery, and tips for conserving battery power. The power system is comprised of two parts, the AC Adapter and the battery system. The AC Adapter converts AC power from a wall outlet to the DC power required by the computer. The Battery Power System Before using the computer on battery power for the first time, check the battery status icon on the Windows Toolbar to make sure the battery is fully charged. See Battery Status later in this section for a description and explanation of the Windows Battery icon. Charging the battery takes about 2.5 hours to charge when the system is in off state. If possible, always charge the battery completely. If you use the battery so frequently that it exceed more than 20 times by fully discharging/charging in a single month alone, we recommend you to perform the “Battery Calibration” process every 3 months to maintain the battery life. Please refer to the topic on “Battery Calibration” describing how to calibrate your system battery discussed in the latter part of this chapter. If you discover the battery life is getting shorter, please 30 perform the “Battery Calibration” process immediately. Removing the Battery Pack To remove the battery pack from its compartment, please refer to Chapter 3, Inserting and Removing the Battery Pack. Preparing the Battery Pack for Use (Battery Calibration) Before using the battery pack for the first time, battery pack should be calibrated in order to get accurate reporting of remaining battery life status.. To calibrate the battery pack follows the instructions below: 1. Insert the battery into the battery compartment and turn on the notebook. If the battery is completely without power go to the next step. Otherwise, let the battery run down until the battery low-low warning beeps are heard. The system will automatically enter Suspend mode. 22. Turn the notebook off. Connect the AC adapter and let the battery fully recharge. When the battery charge indicator turns off, the battery is fully charged. 23. Turn On the notebook, let the battery run down until the battery is in low-low state and you hear a warning beeps. The system will automatically enter the Suspend mode. You can now connect the AC adapter. 24. The battery pack is now calibrated properly. In general, using the battery until the low-low battery-warning indicator appears and fully recharges the battery each time (full discharge/charge cycle) will ensure the accurate reporting of the battery gauge status. Automatic Battery Pack Charging Function To charge the battery, while the battery pack is in the notebook, plug the AC adapter into the notebook and an electrical outlet. The charging time is approximately 3-4 hours when the notebook is turned off and approximately 6-7 hours when the notebook is turned on. When the battery is fully charged, the battery charge indicator becomes off. 31 If system runs at heavy loading or in high temperature environment, the battery may not be fully charged. You need to continue to charge it with the AC adapter plugged in until the charging LED turns off. Battery Status Windows 7 has an applet in the Control Panel that will display an icon in the Windows taskbar indicating when the notebook is running on battery power or is attached to the AC adapter. This applet also displays a meter that indicates how much charge is remaining in the battery. Battery Low Warning When the pack initially reaches the “Battery Low” state approximately 7 ~ 10 minutes of the usable battery life is left. You will hear an audible beep signal every 15 seconds alerting you to the “Battery Low” status. When the battery power reaches the “Battery Low Low” status the beeping sound will accelerate. Your battery now has 1 ~ 2 minutes of battery charge remaining. You must save your data or connect AC power immediately; otherwise, you may lose your data. Sound Continuous beeping every 5 seconds Beeping accelerates Meaning Battery Low: Indicates that there is 7 to 10 minutes charge remaining. Battery Low Low: Indicates that there is 1 to 2 minutes of battery charge remaining. Save your work and turn off the notebook, or connect the AC adapter. When there is only one minute of battery charge remaining, the notebook will suspend to the HDD and power off. You should connect AC power and resume save your work. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power. 32 Resetting the System After installing a software application package, you may be prompted to reset the system to load the changed operating environment. To reset the system, or “reboot,” press the [Ctrl]+[Alt]+[Delete] keys simultaneously. This is known as “warm boot.” This key combination acts as “software” reset switch when you encounter hardware or software problems, which lock up the notebook. If this key combination does not shut down the notebook, you can reset the notebook by using the notebook’s power button. Should the notebook lock up for some reason, pressing this button powers the notebook off. Adjusting the Brightness To adjust the brightness on the LCD screen, press and hold down the [Fn] key in the lower left hand corner of the keyboard and press the [F8] key to increase the brightness or [F7] to decrease the brightness. Using the Windows Help Windows 33 For Windows 7 help, click Start Help and Support icon will open the dialog box. Desktop Desktop may vary differently on the software installed in your notebook with different or additional shortcuts. Recycle Bin Used for storing deleted files in case you want to recover and save it in your system. The files will only be deleted from the Recycle Bin permanently only if you empty it by right clicking your mouse and select the “Empty Recycle Bin”. 34 Start Button Allows easy access to all Windows programs. The Start menu allows you to adapt and show the programs used most frequently. If you wish to keep an item, right click the item and click Pin to Start menu. Log Off will enable the current user to log off and allows a new user to log on. Turn Off Computer allows you to shut down, restart, and Stand by modes for power saving purposes. Taskbar When you open a program, its icon is displayed at the taskbar for you to conveniently move between programs by clicking the relevant button. To add or remove toolbars from the taskbar: right click an empty spot on the taskbar, select Toolbars choose the toolbar you want to add. Notification The icons that appear here are for quick access to some programs and computer functions that you frequently used. To prevent Windows 7 from hiding icons: From an empty spot on the Taskbar, right click your mouse and select the Properties, remove the checked mark on the Auto-hide the taskbar. 35 Control Panel It is in this area that you can change how Windows looks and works. Click Start Control Panel dialog box. There are two interfaces – Classic View. 36 37 Internet Connection Using Wireless LAN Network for Connection to Internet 38 39 40 Running BIOS Setup The Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output System). It runs and maintains a variety of hardware functions. It is menu-driven software, which allows you to easily configure and change the settings. The BIOS contains manufacturers default settings for the computer’s standard operations. However, there are occasions when you may be required to modify the default settings in the BIOS. The BIOS allows you to set up passwords to limit access to users. This is an important feature because a great deal of vital information is carried within the computer nowadays. Unauthorized access can be prevented. Later in this chapter, you will learn how to use this security feature. Entering the BIOS Setup Screen First turn on the power. When the BIOS performs the POST (Power-On Self Test), press F2 key quickly to activate the BIOS Setup Utility. You may need to press F2 key fairly quickly. Once the system begins to load Windows, you may have to retry by cycle-power on again Leaving the BIOS Setup Screen When you have finished modifying the BIOS settings, exit the BIOS. It takes a few seconds to record changes in the CMOS. 41 BIOS Action Keys Function Key ESC Enter F1 F9 F10 Command Description Leaves a sub-menu to return to the Exit previous menu OR exits the BIOS setup while saving changes. Go to Sub Screen Shows the Sub Menu General Help Shows the Help Screen Default Set as default Saves changes and reboots the Save and Exit computer. Select a field Selects the next field. Select an item Selects the next upper item. Select an item Selects the next lower item. Select a menu Selects the right item Select a menu Selects the left item Lower value Selects the lower value within a field. Higher value Selects the higher value within a field. Modifying the BIOS Settings The BIOS setup main menu is subdivided into sub-menus. Each menu item is described in this section. 42 Main Setup Info Setup 43 Advanced Security 44 TPM State Boot Setup 45 Exit Setup 46 47 Super POSH Super POSH is an integrated AP which has great benefit for the system. It includes “Super Power” “Super OSD” “Super Speed” and “Super HDD.” These applications enable you to run the power saving scheme in your system, enable shortcut icon, optimize your system configuration, and detect your system current status. Super POSH System Tray Use your mouse left button by clicking once on the icon will show the status bar. Use your mouse left button by clicking twice on the icon will show the controller at the right side of the screen and main page. 48 The main functions are as follows: Capslock / Silent mode / Touchpad / WLAN / Webcam / Bluetooth / Numlock / Scroll lock / Brightness / (sound) volume / Discrete / UMA Super Power Super Power provides an integrated page for user to control power management. It could increase battery life and provides effectiveness of your system. 49 There are 4 Modes for selection with their description shown below: Mode Power saving Icon Description Decrease system performance to provide more battery life Normal Balance system performance High performance Provide system best performance Dynamic switch Switch to “Power saving” & “ Normal” mode automatically on battery mode, and auto switch to “High performance” mode when plug-in. Power Status Show Current Power Source from AC or Battery. Battery mode Plug-in and Charging Plug-in and Full 50 AC only Setting Page Monitor HDD Stand by Brightness CPU Power Saving Hibernate LCD will be turned off after the interval time and setting of the OS if keyboard or mouse is not operated and no movie/game System will spin down disk after the interval time and setting to OS. System will sleep after the interval time and setting to OS. Adjust range is “Never” to “5hrs”. Show the LCD monitor brightness level through EC sent out code. *Brightness level synchronize with Fn-key. Lower CPU level in order to save power If users disable Hibernate, the option of Hibernate will not show in “Setting Page.” System will hibernate after the interval time and setting to OS. • Adjust range is “Never” to “6hrs”. • Setting the idle time to hibernate must longer than Standby. If “default” was checked, mode would switch to default setting. * Press “OK” after the change “Monitor” “HDD” Stand by” and “Hibernate” items, and setting would be applied. * Setting would be applied and saved automatically after the change “Brightness” “CPU Power Saving” and “Default.” Default 51 Advanced Page Hibernate Wallpaper Turn off LCD Turbo mode Advance power engine SmartEye Allow Windows Power Plan Auto Switch Mode when Plug-in/out Power off Audio 52 If users disable Hibernate, the option of Hibernate will not show in “Setting Page.” Default: ON Desktop background will be white. Press button to turn off the LCD immediately. Default: ON Overclocking CPU instantly. • Function options depend on the definition of product specification. Drop efficacy to save the battery power. • Function options depend on the definition of product specification. LCD will be turn off automatically if user leaves for a definite time. • Only when plug-in and webcam on. • If webcam is busy when executing the Super POSH, Smarteye will be turn off automatically. Enable select Windows or Super POSH’s power plan The system will switch mode automatically. When adaptor is plug in, the system will switch to High Performance mode. When the adaptor is unplug, the system will switch to Power Saving mode. Default: ON • Dynamic switch mode has higher priority. Turn off audio power instantly to save the battery power. • Function options depend on the definition of product specification. Quickkey for Super Power Press Quick key to switch among each power management modes and on-screen display. Warning: If the percentage of battery was under 10%, there will pop a warning window on task icon. Super OSD (On-Screen-Display) Super OSD provides several styles and locations selection of OSD. And also could get the current status of OSD from status bar. 53 >> or << to preview function and OSD pictures. OSD Style: Blue, Green and Orange. Status: This area displayed the current status of OSD. Status bar will auto detect device connected in your system. If the color of the icon is yellow, it means the function is working. If the color of the icon is gray, it means the function is turn off. The value of volume and brightness also show at the side. The icon of status bar depends on product specification. Caps Lock On/Off Silent Mode On/Off TouchPad On/Off Power of WiFi On/Off 54 Webcam On/Off Bluetooth On/Off Number Lock On/Off Scroll Lock On/Off Brightness Level (0~7) Mute On/Off Volume Level (0~10) 3G On/Off Moving status bar: It would show on the screen as OS ones. It can be vertical or horizontal, and can be moved arbitrarily. Volume Level Definition: Volume level value are as below Level Volume Value 10 11 20 21 30 31 40 41 50 51 60 61 70 71 80 81 90 10 91~ 100 * When adjusting the volume level, volume value will become current level x10 automatically. There are two options to either enable or disable the OSD. Uncheck the “Disable OSD”, the system will not show the OSD picture. Uncheck the “Display OSD Status bar”, Status bar will be closed. 55 MMB- depends on product specification. OSD location: There are 9 locations for choosing. 56 An example is shown below where the OSD is shown on the lower right corner of the screen. Super OSD functions are as follows: The function will depend on the definition of product specification. Function Preview Bluetooth Silent mode Mute (speaker only) Volume Brightness Touchpad Wireless Webcam 3G Caps Lock Num Lock 57 Scroll lock Web browser Media player Play Previous Rewind Stop Fast forward Next VGA/UMA Super Speed Super Speed optimizes and cleans the system to obtain the best effectiveness and fragmentation. 58 Optimizing Windows Setting: Click “Optimize” button after selecting the optimizing options to improve system performance. Click “Restore” button to restore the system to original status. After “Optimize” or “Restore” are executed, please reboot the computer for the changes to take effect. Click will pop a .txt file describing the detailed information about the options The options are described in the following table: Options Visual Effect Service Boot Shutdown Network System Description Modify visual effect setting to increase the performance of the system. Terminate uncommon programs running in the background when Windows is running. Speed up the time for booting up the system. Speed up the time to shutdown the system. Modify network setting to improve the performance of the network. Modify system setting to increase the performance of the system. 59 System Disk Cleanup: Click “Analyze” button to analyze the system. Click “Free” button after selecting the options to free up system disk space. The options are described in the following table: Options Description System temporary files Internet temporary file Clean the unnecessary files in Windows Clean the browsing history in Internet Explorer Clean the Recycle Bin in Windows Recycle bin System Disk Defragment: This will show the HDD health status according to “Super HDD” page. It will state a suggestion whether the HDD should be defragmented. 60 Status & Picture Super HDD Super HDD displays the health status of HDD and information of CPU and RAM. Information of main HDD: Name, Type, Partitions and Total Size. Use scroll bar to choose the partition, it will display File system, Total Size and Free Size of in partitions. Hard Disk Menu Normal: Show the HDD Health Index according to S.M.A.R.T result. 61 HDD Health Index Condition Healthy HDD status will be healthy if all status of items are normal. Warning HDD status is in warning state if there are more than one warning item. Danger HDD status is in danger state if there more than one danger item. Not Support HDD does not support this function. Advanced : There were 46 attributes from S.M.A.R.T to determine the HDD health Index. Item's status depends on 3 main values: A: threshold, B: worst, and C: current value. The rule of judging conditions as stated in the following items: CPU Information of the main CPU: CPU Name, CPU Tag, Cores Number, Max clock Speed and Current Clock Speed. Super POSH will auto detect the maximum temperature of CPU, and display on the following table: Display Status Normal Warning Danger Percentage of limit temperature Under 69% 70~89% 90~100% Color Green Orange Red RAM: Information of main RAM: Total Memory Size, Free Memory Size, Percent of used RAM and Usage Processes Number. 62 Wa r n i n g : If the status of HDD and CPU is Danger, a warning window will pop up on the POSH icon. Setting page A: Show “about” in the top area. Include: Icon, Version, release date and information of every pages. B: Setting Options: Advanced setting of super POSH. Options ToolTip Refresh time Description Whether show ToolTip and Warning message Refresh battery status time * Refresh time would affect synchronized time with OS and discharge time. Status ON/ OFF 1,2,3,5,10,30sec, 1,2,3,5min C: Company information: A customized area. Depend on the definition of customer. Show Company name, email, address…etc. Logo dimension (pixels): 350 x 80 63 64 Troubleshooting Your computer has been fully tested and complies with the system specifications before shipping. However, incorrect operations and/or mishandling may cause problems. This chapter provides a reference for identifying and correcting common hardware and software problems that you may encounter. When you encounter a problem, you should first try to go through the recommendations in this chapter. Instead of returning the computer and waiting for repair, you may easily solve the problems by considering the following scenarios and possible solutions. If the error continues, contact your reseller for service information. Before taking further actions, consider the following suggestions: Check to see if the problem persists when all the external devices are removed. Check to see that the blue light indicator on the AC adapter is lit. Check to see the power cord is properly plugged to the wall outlet and to the computer. Check to see the power indicator of the computer is on. Check to see if your keyboard is operational by pressing and holding any key. Check for any incorrect or loose cable connections. Make sure the latches on the connectors latch securely on to the receptor end. Be sure you have not performed an incorrect setting on the hardware devices in the BIOS Setup utility. A faulty setting may cause the system to misbehave. If you are not sure of the changes you made, try to restore all the settings to factory defaults. 65 Be sure all the device drivers are installed properly. For example, without the audio driver properly installed, the speakers and microphone will not work. If external devices such as USB cameras, scanner, printer do not function correctly when connected to the system, it is usually the device’s own problem. Consult the device’s manufacturer first. Some software programs, which have not gone through rigorous coding and testing, may cause problems during your routine use. Consult the software vendor for problem solving. Legacy peripheral are not plug-and-play capable. You need to restart the system with these devices powered up and connected first. Be sure to go to BIOS SETUP and load DEFAULT SETTING after BIOS re-flash. 66 67 Specification O.S. Supports Windows 7 Home Premium CPU Support Intel Sandy Bridge & Integrated Gfx Intel Turbo Boost Technology i5-2520M,i5-2540M, i5-2530UM i7-2620M (2.7GHz/ 1core-3.4GHz; 2core3.1GHz) Memory DDR3 speed up to 1066MHz SO-DIMM*2, Max. support to 8GB Core Logic Intel Cougar Point Intel Vpro Support AMT (which allow remote access to the PC for management and security tasks) Support Intel TXT (Trusted Execution Technology) Support Intel VT (Virtualization Technology) Audio Codec Realtek ALC269Q-GR 68 Card reader (6 in 1) Support MS, MS PRO, MMC, SD, SDXC, SDHC Memory Card LAN Controller Supports 10/100/1000Mb/s GigaLAN solution Provide a standard IEEE802.3 Ethernet interface for 1000BASE-T, 100BASE-TX, and 10BASE-T applications (802.3, 802.3u, and 802.3ab) Support EEE 802.az Wireless LAN Support Half-Mini Card (HMC) type only IEEE 802.11 A/G/N (2x2) PCI-E interface Camera CCD (Optional) Support 1.3M HD up to 2.0M camera Keyboard US-300.8mm keys KB support Pointing Device PS2 Touch Pad with 2 buttons Support gesture function LCD 14" (16:9) HD 1366 x 768 LED-Back Light Unit Support 16:9 5.2mm thickness LED panel Battery Pack SMP+BAK cell 6 cells, 11.1V/4400mAh (3S2P), SMP +BAK Battery GLW+LG cell 6 cells, 10.8V/4400mAh (3S2P), GLW+LG Battery 69 AC-Adapter Automatics Voltage adjustment between 100 and 240VAC 50/60Hz, 19 V/65 Watts, 2Pin, Level 5n. Huntkey type: HKA06519034-8C/ HKA06519034-6C Delta type: ADP-65JH AB/ ADP-65JH BB Lite-On type: PA-1650-65/ PA-1650-68 Speaker/MIC Build-in 2 speakers Internal Microphone support BIOS Supports PnP, ACPI 3.0 Support external USB flash memory card boot up. With Phoenix BIOS and 4MB flash ROM Power Management (default: Silent mode) Proprietary Technology of Battery Life and System performance Extension Physical Outline Dimension: 344X 344 x 248.5 x 32.8~38.3mm (w/ Battery w/o rubber foot) Weight: 2.13 Kg w/ 4 cell battery (w/ ODD) Weight: 2.22 Kg w/ 6 cell battery (w/ ODD) EMI FCC Safety ETL 70
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39 Producer : GPL Ghostscript 9.0 Keywords : Modify Date : 2011:08:22 13:49:44-07:00 Create Date : 2011:07:11 09:43:34+08:00 Creator Tool : PDFCreator Version 1.1.0 Metadata Date : 2011:08:22 13:49:44-07:00 Document ID : d29a0bfe-adba-11e0-0000-2c7ad7e36e39 Instance ID : uuid:7977e5c0-fb38-4fc6-9adb-5700789f998a Format : application/pdf Title : BR45II7_english Creator : Leoz Description : () Has XFA : No Page Count : 75 Subject : Author : LeozEXIF Metadata provided by EXIF.tools