Fiplex Communications DHS00-M PS800 DIGITAL MASTER UNIT User Manual TETRA User s Manual
Fiplex Communications Inc PS800 DIGITAL MASTER UNIT TETRA User s Manual
User Manual
English DHSxx – PS800 Digital Fiber DAS User & Installation Manual Document History Description Revision Date Issued Original version 1.0 July 3rd, 2014 General Review 2.0 March 2nd, 2016 General Update 3.0 7 June, 2017 UM-0909 II About this manual This manual describes installation, commissioning, operation and maintenance of the Fiplex PS800 Digital Fiber DAS, and Fiplex Control Software (FCS). The hardware included in this manual corresponds to the Digital Master Unit (DM) DHS00M and Digital Remote Unit (DR) DHS37-R. The first part of the manual describes the Digital Fiber DAS hardware and the second part describes the software. Hardware and software mentioned in this manual are subjected to continuous development and improvement. Consequently, there may be minor discrepancies between the information in the manual and the performance and design of the hardware and software. Specifications, dimensions and other statements mentioned in this manual are subject to change without notice. This manual or parts of it may not be reproduced without the written permission of Fiplex Communications Inc. Infringements will be prosecuted. All rights reserved. Copyright © Fiplex Communications Inc, Miami, 2017. UM-0909 III Abbreviations AGC AMPS ARFCN BCCH BS CDMA DC DCS DL DPLX EEPROM EGSM ETACS ETSI FCS GSM HW LED LNA MS OMS OL PA PCN PCS PS RF RSSI SW TDMA UL WEEE UM-0909 Automatic Gain Control Advanced Mobile Phone Service Absolute Radio Frequency Channel Number Broadcast Control Channel (GSM broadcast channel time slot) Base Station, BS antenna = towards the base station Code Division Multiple Access Direct Current Digital Communication System (same as PCN) Downlink signal direction (from base station via repeater to mobile station) Duplex filter Electrical Erasable Programmable Read Only Memory Extended Global System for Mobile communication Extended Total Access Communication System European Telecommunications Standard Institute Fiplex Control Software Global System for Mobile communication Hardware Light Emitting Diode Low Noise Amplifier, uplink and downlink Mobile Station, MS antenna = towards the mobile station Operation and Maintenance System Overload Power Amplifier Personal Communication Network (same as DCS) Personal Communication System Power Supply Radio Frequency Received Signal Strength Indication Software Time Division Multiple Access Uplink signal direction (from mobile station via repeater to base station) Waste of Electric and Electronic Equipment IV Part 1 HARDWARE 1. Safety Caution! This manual lists a set of rules and warnings to be accomplished when installing, commissioning and operating a Fiber DAS Master Optical Unit from FIPLEX. Any omission may result in damage and/or injuries to the System and/or the System Operators or Users. If an instruction is not clear or you consider is missing, please contact immediately to Fiplex. See www.fiplex.com for contact information. Dangerous Voltage Warning Any personnel involved in installation, operation or service of this equipment must understand and obey the following: The power supply unit supplied from the mains contains dangerous voltage level, which can cause electric shock. Switch the mains off prior to any work in such equipment. Any local regulations are to be followed when servicing MOUs. Authorized service personnel only are allowed to service repeaters while the main is switched on. R&TTE Compliance Statement This equipment complies with the appropriate essential requirements of Article 3 of the R&TTE Directive 1999/5/EC. Station Ground BTS chassis, MOU, feeders, donor antenna, service antenna/s and auxiliary equipment (splitters, tabs, .etc) are required to be bonded to protective grounding using the bonding stud or screw provided with each unit. Electrostatic Discharge Static electricity means no risk of personal injury but it can severely damage essential parts of the equipment, if not handled carefully. Parts on the printed circuit boards as well as other parts in the unit are sensitive to electrostatic discharge. Never touch printed circuit boards or uninsulated conductor surfaces unless absolutely necessary. If you must handle printed circuit boards or uninsulated conductor surfaces, use ESD protective equipment. Never let your clothes touch printed circuit boards or uninsulated conductor surfaces. Disposal of Electric and Electronic Waste Pursuant to the WEEE EU Directive electronic and electrical waste must not be disposed of with unsorted waste. Please contact your local recycling authority for disposal of this product. Class 1 Laser. MOU1x Series is equipped with Class 1 Laser according to EN 60825-1. Cautions: Never look directly into the laser beam. Never point a laser beam at a person. Do not aim the laser at reflective surfaces. User Manual– Digital DAS CLASS 1 LASER PRODUCT Fibers carry transmission power in both direction due to the use of WDM Never view a laser pointer using an optical instrument, such as binocular or a microscope. Never handle non-dark fibers. RF Exposure. As a part of a Telecommunications System, MOU1x is not intended to radiate signals and meets EMC directives, but within the System may have cables and antennas that are potential sources of radiating. Contact the System Design to verify the compliance of the Exposure to Non-Ionising Radiation. UM-0909 FCC Compliance This is a 90.219 Class B device. WARNING: This is a 90.219 Class B device. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. You MUST register Class B signal boosters (as defined in 47 CFR 90.219) online at www.fcc.gov/signalboosters/registration. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. The installation procedure must result in the signal booster complying with FCC requirements 90.219(d). In order to meet FCC requirements 90.219(d), it may be necessary for the installer to reduce the UL and/or DL output power for certain installations. ATTENTION: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. ATTENTION: FCC regulation mandate that the ERP of type B devices should not exceed 5W. This device has a maximum programmable composite output power of 5W (+37dBm), therefore the gain of the DL antenna should be of 0dBi or less and maintain a minimum separation of 45 cm from all persons, and the gain of the UL antenna should be 13dBi or less and maintain a minimum separation of 45 cm from all persons. IC Compliance As per RSS 131 Issue 2: Nominal passband gain: 80dB max Nominal bandwidth: 18MHz maximum for Canada market Rated mean output power: Up to +37dBm maximum. Input and Output impedances: 50 ohms The Manufacturer's rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device. RF Exposure Statement for ISED: “This device complies with Health Canada’s Safety Code. The installer of this device should ensure that RF radiation is not emitted in excess of the Health Canada’s requirement. Information can be obtained at http://www.hc-sc.gc.ca/ewhsemt/pubs/radiation/radio_guide-lignes_direct/index-eng.php” UM-0909 The antenna/s used for this transmitter must be installed to provide a separation of at least 45 cm in DL and 45 cm in UL from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Selon RSS 131 Issue 2: • Gain de bande passante nominal: 80dB max • Bande passante nominale: 18MHz maximum pour le marché canadien • Puissance nominale de sortie moyenne: Jusqu'à + 37dBm maximum. • Impédances d'entrée et de sortie: 50 ohms La puissance de sortie nominale du fabricant de cet équipement est pour le fonctionnement d'une seule porteuse. Pour les situations où plusieurs signaux de porteuse sont présents, la cote devrait être réduite de 3,5 dB, en particulier lorsque le signal de sortie est ré-irradié et peut causer des interférences aux utilisateurs de bande adjacents. Cette réduction de puissance doit se faire au moyen d'une puissance d'entrée ou d'une réduction de gain et non pas par un atténuateur à la sortie du dispositif. Déclaration d'exposition RF pour ISED: «Cet appareil est conforme au Code de sécurité de Santé Canada. L'installateur de cet appareil doit s'assurer que les rayonnements RF ne sont pas émis au-delà de l'exigence de Santé Canada. Vous pouvez obtenir de l'information à l'adresse http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct/index-fra.php. L'antenne utilisée pour cet émetteur doit être installée de manière à assurer une séparation d'au moins 45 cm dans DL et 45 cm dans UL de toutes les personnes et ne doit pas être collocée ni fonctionner avec une autre antenne ou émetteur. Les changements ou modifications non expressément approuvés par la partie responsable de la conformité pourraient annuler l'autorisation de l'utilisateur d'utiliser l'équipement. UM-0909 2. Product Description. The Fiplex PS800 Digital DAS has a modular structure that consists on two different modules, the Digital Master Unit DHS00-M and the Digital Remote Unit DHS37-R. Each one of the different modules is enclosed in the same or equivalent case, therefore, product description and installing instruction sections are valid for all of them. The Fiplex Digital Master is a RF-to-Fiber and Fiber-to-RF conversion system. These conversions are done using FPGA based Digital Signal Processing. It provides a connection to the Base Station and it centralises all the connectivity of the DAS. It also provides the possibility to connect up to six Digital Remote Units. The Digital Remote Unit, also is a RF-to-Fiber and Fiber-to-RF conversion system. These conversions are also made using FPGA based Digital Signal Processing. It provides amplification to the RF signals needed to provide signal amplification into the target area. The Master and Remote Units is where the RF interfaces are located, the Master Unit has the “To Base” interface, and the Remote Unit has the “To Mobile” interface. The Master and Remote Units have internal duplexers therefore, the RF interface will have one RF port in each unit, the Master will have a “To Base” RF Port, and the Remote Units will have “To Mobile” RF Ports. The advantages of using digital signal transportation over fiber are to avoid the addition of the fiber analog noise when it is used to transport analog signals. Along with this, the UL squelch of the Digital Remote Unit works not only per channel but also per time slot, this makes the Fiplex Digital DAS solution unique by its outstanding management of the UL noise. The Fiplex Digital Master Unit can be fed with a number of Base Stations or Off the Air. The direct connection to a base station is done though the Point Of Interconnection (POI) and depending on the configuration and amount of Base Stations it can be something simple as a directional coupler and a duplexer or something more complex that can consist on several directional couplers, splitters, duplexers. The Fiplex Digital Master Unit also provides an access point to monitor and control all the system parameters not only of the Digital Master Unit but also to each Digital Remote Unit connected on the system. This connection can be done locally via USB or Web-Browser, or remotely using Ethernet (via SNMP protocol). The DHS00-M and DHS37-R are NFPA Ready orderable with AC or DC option. As optional it can have remote control via Ethernet or via wireless modem. The Digital Master Unit and the Digital Remote Units both have heavy duty IP67/NEMA4X cabinet for outdoor usage, it is designed to be wall or pole mounted, however, to mount on standard 19” rack, a special mounting kit can be supplied. For more details refer to the product datasheet. UM-0909 2.1 Digital Master Unit Ports The Digital Master Unit is equipped with internal duplexers, therefore, the enclosure has the “To Base” RF Port. UM-0909 2.2 Digital Remote Unit Ports The Digital Remote Unit is equipped with internal duplexers, therefore, the enclosure has the “To Mobile” RF Port. UM-0909 2.3 FO Connection 2.3.1 FO Connection in Master Unit Note: Each fiber connection is performed with simplex fiber and LC-APC connector. UM-0909 2.3.2 FO Connection in Remote Unit Note: Each fiber connection is performed with simplex fiber and LC-APC connector. UM-0909 2.4 Dimensions 2.4.1 UM-0909 Digital Master, Expansion and Remote Unit Cabinet Dimensions 10 3 Installation Mounting the cabinet Fiplex Digital DAS is designed for outdoor usage with a weather proof outdoor NEMA4 cabinet that can be mounted without any kind of shelter from rain, snow or hail. However, to improve reliability, it is recommended to mount the Digital DAS on a site with shelter from direct exposure to sun, rain, snow and hailing. It is not recommended to operate the DAS under bad weather conditions, such as: - Intense rainfall, snowfall or hail - Storm or high wind - Extremely low or high temperature - High humidity of the air Mounting 1. Mount the bracket The cabinet can be mounted on a wall or pole. These mounting cases are shown below in Figure 1 and Figure 2. The bracket is provided with each cabinet. Figure 1 Figure 1 shows a bracket attachment to a wall using three fixing screws. Figure 2 Figure 2 shows a bracket attachment to a pipe using four inox hose clamps (provided with bracket). UM-0909 11 2. After attaching the bracket hang the cabinet as shown in Figure 3. Figure 3 UM-0909 12 3. Secure the cabinet to the bracket as shown in Figure 4. To attach the cabinet to the bracket use the provided four M6 x 1/2” allen screws. Figure 4 UM-0909 13 Opening and Closing the Cabinet To open the cabinet, release the 8 door screws indicated in figure 5 using the provided special allen key. A - Release cabinet cover. Figure 5 Use the special allen key N°6 UM-0909 14 B - Open the cabinet cover. Figure 6 C – Close the cabinet cover. Figure 7 UM-0909 15 D - Secure cabinet cover. Figure 8 UM-0909 16 Use of Liquid Tight Conduit The unit has available a Liquid Tight Conduit Fitting connector. The unit as standard has the connector installed, so if the user requires to use this connector, if available, the NFPA cables, Ethernet, DC and AC cables can be routed through this connector. Figure 9; AC Routing through cable gland or conduit connector If the is not going to use Liquid Tight Conduits, then the connector should be replaced by the provided sealing cup as indicated in Figure 10. A - Remove the conduit connector UM-0909 17 B – Install the sealing cup Figure 10; Replacement of Conduit connector to sealing cup Nema4X considerations This device is equipped with a Nema4X enclosure, however, to ensure the Nema rating, the user must have the following considerations: 1. Correct use of the Liquid Tight Conduit. In case this interface is not used, it should be replaced with the sealing cup. 2. Sealing cups should be installed in the non-used cable glands. 3. The RF Ports should be perfectly mated. UM-0909 18 4 Commissioning 4.1 Connection step by step Connect the RF ports, Power, Fibers and Ethernet Cable Glands location, for Master, Expansion and Remote units following the next steps: 1. For Master Unit: a. Connect the signal coupled from the base station to the “To Base” RF port. N type female connectors are used in the unit. The coupling to Base station can be done with a Donor antenna or through a POI. b. Connect fiber cables to internal optical modules. LC-APC connectors are used in the unit. Connect the remote units on the dedicated ports and the expansion units on the dedicated ports. c. Connect USB Cable for local management. 2. For Remote Unit: a. Connect service antenna (“RF To Mobile” port) coaxial cable to remote unit. N type female connectors are used in the unit. b. Connect fiber cable to internal optical module. LC-APC connector is used in the unit. 3. Once RF ports of the unit are properly loaded connect the Main Power the AC or DC source depending on the model. If using the AC model, electrical installation must provide differential and thermo-magnetic breaker elements according to electric safety international regulations. DB TMB 4. For NFPA connection in Master and Remote, there is a dedicated cable gland for this purpose (“NFPA” in figure 11 and 12). A multi-conductor cable can be used to connect the NFPA dry contacts to the Fire Department Control Box. NC NO VSWR UM-0909 NC NO Repeater Fail Status of contacts (Alarms Off) Pin 1 – 2 = VSWR (normally closed contact) Pin 2 – 3 = VSWR (normally open contact) Pin 4 – 5 = Repeater Fail (normally closed contact) Pin 5 – 6 = Repeater Fail (normally open contact) 19 Figure 11; NFPA Dry Contact connection configuration Figure 12; NFPA Dry Contact connection location inside the cabinet 5. Once the unit has been connected to the power source, it takes about 30 seconds to run a booting routine. After that time unit is ready to be connected via USB cable to the Digital Master to a computer running Fiplex Control Software (FCS) in order to be properly configured. Figure 13; USB Port location UM-0909 20 4.2 Starting Operation BE SURE THAT “TO MOBILE” AND “TO BASE” PORTS ARE PROPERLY LOADED EITHER WITH 50 OHMS DUMMY LOADS, OR RADIATING SYSTEM. 1. Turn on the repeater, connect computer to repeater through USB cable, and run Fiplex Control Software. Check that all remote units are connected to the master through fiber optic checking link status. Link status 2. UM-0909 Enable channel filtering if needed and setup desired channel frequencies. If Fiplex Digital Fiber DAS is used as channel selective, user has to know what frequencies are used in base station. Each channel can be enabled independently. Channels not used can be showed / hidden using the “Show channels” checkboxes. If remote units are on and connected through optical fiber, the corresponding uplink frequencies will be automatically set, too. 21 Set number of active channels and frequencies 3. According to DL RF input levels, program input attenuator to avoid input overflow, and output attenuator for each remote to obtain desired output level in each remote. Set Input attenuator Set Output attenuator 4. UM-0909 Reciprocally, set UL band gain adjusting output attenuator of master unit. It is recommended that DL gain and UL gain be equal. 22 Set Output attenuator Check UL and DL gain for each remote 5. Set up squelch settings. Controls are independent in UL (for each remote) and DL (master) bands. Typical values for UL are between -110dBm and -100dBm for squelch threshold. For DL, recommended value for squelch threshold is minimum level received in any active channel minus 10dB. DL squelch settings UL squelch settings 6. UM-0909 Setup desired filter bandwidth, depending on presence of adjacent channels. In principle, recommended bandwidth filter is 90KHz due to its low delay, but if adjacent signal is detected, narrow filters can be used. Fine gain can be set to equalize input signals. 23 Filters and fine gain settings UM-0909 24 4.3 Status Indicators There is an indicator panel located at the front panel of the repeater. This led panel works as a status monitor, in order indicate warning or alarms of repeater There are four leds, first one the power ON indication led, labelled “PWR”. A Second led, labelled “STS” summarizes warnings regarding critical operational conditions of the repeater. Third and fourth led summarizes operational conditions for uplink “UL” and downlink “DL” chains. In general, leds has four states: off, slow blinking, fast blinking, on. Table 1 describes alarm and warning conditions for each led state in the master device and Table 2 is for remote devices. Table 1 Indicator Panel LED indication description Unit is not powered or fail in power supply Normal state: Unit is powered on Normal state HW fail: digital signal processor is not detected Temperature: very high internal unit temperature Optical fiber alarm in at least one link TBS Warning: No signal is detected coming from base station Normal state RF input overflow: maximum level at RF input is exceeded Normal state Where: Led OFF Led slow blinking with period of 2 seconds aprox. WARNING Led fast blinking with period of 0.5 seconds aprox. ALARM Led ON UM-0909 25 Table 2 Indicator Panel LED indication description Unit is not powered or fail in power supply Normal state: Unit is powered on Normal state HW fail: digital signal processor is not detected Temperature: very high internal Unit temperature Optical fiber alarm in at least one link Normal state PA Overflow or excessive temperature alarm. PA Underflow: PA output level is lower than +25dBm Normal state Where: Led OFF Led slow blinking with period of 2 seconds aprox. WARNING Led fast blinking with period of 0.5 seconds aprox. ALARM Led ON 4.4 Laboratory Measurements For specific parameters verification and laboratory tests, please contact factory. Detailed procedures, recommended tests set up, and a knowledge engineering team will bring adequate support to perform this measurements in a comfortable and safely way. UM-0909 26 Part 2 SOFTWARE Introduction Fiplex Fiber DAS can be fully configured and monitored through USB connection. Digital Master unit receives through optical links monitoring and configuration data from remotes units. For this reason, whole system can be fully configured and supervised from digital master unit. USB Software 6.1 Software description (Digital Master) If software has been successfully installed and connected to Digital Master (see section 7) status screen will appear. In this screen, RF configurations parameters (channel frequencies, bandwidth filter, gains / attenuation) and RF and optical links monitoring (RF input/output levels, AGC status, optical link status) are shown. At left side of webpage, configuration menus are shown: Content UM-0909 Status: whole RF configuration and monitoring parameters are shown. These parameters are described in next section. Tag: user can set a tag to ease repeater identification. For modifying the TAG, write a new value in text field and click over Apply Changes link 27 UM-0909 IP: At this page (for units with Ethernet supervision), IP addresses configuration and addresses of SNMP Managers are shown. User can set addresses of two SNMP Managers (IP where SNMP agent will send TRAP information). To modify, click over Apply Changes link after writing new values on text fields. Also router 3G IP address can be viewed in this screen (if 3G router option is installed) Downlink Spectrum: in order to know input signal: level of desired channels, unwanted channel levels, Digital Master provides an spectrum analyzer that shows input signal in frequency domain. Date & Time (for units with Ethernet supervision): page to modify real time clock. When the repeater is not powered, this clock runs with a voltage supply provided by 28 a 3V lithium battery, button type of 20mm (CR2032) with 220mA·h. This suffices for at least half year. When the repeater is powered, no current is drained from the battery. So, actual battery life will depend on repeater usage. For battery replacement, please locate battery holder between USB and Ethernet connectors on main board. Battery positive side is UP, i.e. on holder clip. After clicking on “Apply Changes” link, next message will appear, warning the user that system needs to be rebooted. Configuration o Apply Changes: as it is said above, this link is used to load changes to the repeater, in configuration, tag, IP, password and date and time menus. After any configuration change, web page will show and icon that allows user to know if configuration has been successfully applied: Reload Settings: clicking this link, repeater configuration data is refreshed. Version: shows hardware, firmware and software versions of repeater and serial number. 6.2 RF parameters description (Digital Master) “Status” menu shows whole RF configuration and RF and optical links monitoring data that are distributed along the webpage. The first frame called “MASTER” is placed in top of webpage, showing configuration of digital master unit. Below this, some frames titled “REMOTE 1”, “REMOTE 2”... . There is one for each remote unit connected to the master, and configuration and status information related to each remote can be viewed. Next figures show these frames: UM-0909 29 Digital Master frame. There are five sub-sections inside this frame: Downlink filtering: this section contains fields to modify channel frequencies, squelch options and filtering options. Parameters are described in following table: Parameter Range Frequency Downlink band Channel enable Enabled / disabled 90KHz / 45KHz / 30KHz / 20KHz / 15KHz Bw Filter Fine Gain Adjust -5 to +5dB Power indicator --- Squelch enable control Enabled / disabled Squelch threshold control -90dBm to 40dBm Filtering enable Enabled / disabled UM-0909 Description Downlink frequency channels. Frequency resolution is 3.125KHz Each of 12 channels can be enabled/disabled Bandwidth of channels filter can be independently adjusted (if filtering is enabled) If filtering is enabled, gain of each channel can be fine adjusted Level of each channel, measured according to its bandwidth filter, is shown in dBm units. Led indicator shows if levels exceeds squelch threshold (green) or not (yellow). Enabling this control, repeater does not transmit in each channel if RF input power do not exceed the threshold level configured according to next row If squelch is enabled, input levels below this threshold are not transmitted. Filtering option can be bypassed. If filtering is disabled, fine gain adjustments and squelch options are ignored Master RF Input parameters. Next table describes information of this frame: Parameter Range Broad band level --- Description This indicator shows input level measured along DL band 30 Overflow Grey: normal state / Red: alarm state Input Attenuator RF IN from TBS (DL) 0dB to 30dB Master RF Output parameters. Next table describes information of this frame: Parameter UL Output power Range --- AGC Grey: normal state / Red: alarm state Output Attenuator RF OUT to Base Station (UL) 0dB to 30dB This indicator shows overflow on input circuitry is occurring. This condition can be avoided increasing input attenuator Input attenuator to accommodate input levels. This value must be set to avoid overflow condition. Together with output attenuator of remotes sets the downlink gain: G_DL (dB) = 80 – AttINmaster(dB) – AttOUTremote(dB) Description This indicator shows output level in UL band This indicator shows gain reduction that master unit is applying at RF output to prevent PA UL overload Output attenuator to adjust UL gain. System UL gain can be computed as: G_UL (dB) = 80 – AttOUTmaster(dB) Master Board status: general parameters of master unit are contained in this frame Parameter Temperature High temperature alarm Signal processor alarm RESET control Range --Grey: normal state / Red: alarm state Grey: normal state / Red: alarm state --- Description This indicator shows unit temperature High temperature alarm condition is indicated with this led. Alarm indicates that digital signal processor is not working properly. With this control, unit can be restarted UM-0909 31 o Optical link status: each indicator shows optical link status between digital master and each remote unit. Clicking on “REMOTE LINK n” detailed monitoring data of each optical link can be viewed: voltage, current and temperature of each optical module, transmitted and received optical power, and alarms related to digital data recovery system. If Expansion Unit is used to increase number of remote units a new frame appears with “EXPANSOR LINK n” title, showing link status (between Digital Master and Expansion Unit). Data of two optical modules involved in each link are shown: master unit side (or expansion unit side) and remote unit side. Remote frame: shows configuration and monitoring information of each remote unit. The frame is divided in the following sections: Uplink filtering: this section shows equivalent parameters of downlink filtering of master unit. Parameter Range Frequency UL band Channel enable Enabled / disabled 90KHz / 45KHz / 30KHz / 20KHz / 15KHz Bw Filter UM-0909 Fine Gain Adjust -5 to +5dB Power indicator --- AGC --- Squelch enable control Enabled / disabled Squelch threshold control -110dBm to -70dBm Description Uplink frequency channels. These frequencies are derived automatically from downlink frequencies, taking into account frequency separation between DL and UL bands Each of 12 channels can be enabled/disabled Bandwidth of channels filter can be independently adjusted (if filtering is enabled) If filtering is enabled, gain of each channel can be fine adjusted Level of each channel, measured according to its bandwidth filter, is shown in dBm units. Led indicator shows if levels exceeds squelch threshold (green) or not (yellow). Show gain reduction to prevent overloading in AGC per channel Enabling this control, repeater does not transmit in each channel if RF input power do not exceed the threshold level configured according to next row If squelch is enabled, input levels below this threshold are not transmitted. 32 Filtering enable Filtering option can be bypassed. If filtering is disabled, fine gain adjustments and squelch options are ignored Remote RF Input parameters. Next table describes information of this frame: Parameter Range Broad band level --- Overflow Grey: normal state / Red: alarm state Uplink gain from remote to master -- Description This indicator shows input level measured in UL band This indicator shows overflow on input circuitry is occurring. Shows system uplink gain for each remote. Can be calculated as: G_UL (dB) = 80 – AttOutMaster(dB) Remote RF Output parameters. Next table describes information of this frame: Parameter Output power level Range Description --- This indicator shows the PA output power PA Overflow Grey: normal state / Red: alarm state Downlink gain from master to remote --- AGC --- Indicates that PA is overloaded. Condition is output power higher than +43dBm Shows downlink gain for each remote. Can be calculated as: G_DL (dB) = 80 – AttInMaster(dB) – AttOutRemote(dB) Shows gainr reduction applied in DL band signal to prevent PA overload UM-0909 Enabled / disabled RF on/off control and Board Status: Parameter Range RF on/off Indicator Green: RF Enabled / Red: RF Disabled RF Enable Control On / Off Description This indicator shows PA status. Power amplifier can be automatically disabled if other alarm conditions occurs: a) Fail in optical link b) PA Overflow With this control RF DL and UL chains can be disabled 33 Output attenuator 0 to 40dB Temperature High temperature alarm RESET control --Grey: normal state / Red: alarm state --- This control sets the output attenuation used to set DL gain together with Master Input Attenuator This indicator shows unit temperature High temperature alarm condition is indicated with this led. With this control, unit can be restarted Optical link status: shows optical link status between master and each remote unit. Moreover, clicking on “REMOTE LINK n” detailed monitoring data of each optical link can be viewed: voltage, current and temperature of each optical module, transmitted and received optical power, and alarms related to digital data recovery system. The main window shows only general parameters: Parameter Range Frequency Sync Green: Normal state / Red: Alarm state Status Rx Detect Green: Normal state Yellow: Warning state Red: Alarm state Green: Normal state Yellow: Warning state Red: Alarm state Error Count --- Rx Power --- Description This indicator shows frequency synchronization status between master and remote unit This indicator summarizes the status of optical module based in voltage, current, temperature and optical transmitted power This indicator summarizes the status of optical reception based in received optical power and digital data recovery system Counter that it is incremented when optical link fails. Shows optical received power. For reliable optical link, RX power must be higher than -25dBm 6.3 Software description (Remote Unit) While software connected to digital master allows configuration and monitoring of whole system, if software is connected to remote unit, only parameters of this unit can be viewed / modified. Then, status screen of remote unit only shows information regarding this unit: UM-0909 34 Distribution and meaning of the controls contained in status page are very similar to single remote frame of master status page, only optical frame is different due to only remote side of optical link is monitored. Local Software. Installation and troubleshooting 7.1 Installation The following section will describe the steps to be followed in order to install and use the Fiplex Control software with your Fiplex repeater. 1. Before connect USB cable between computer and repeater, run the FiplexControlSoftware.msi File. Next screen will appear… UM-0909 35 2. Choose the default installation path “C:\Program Files (x86)\FiplexControlSoftware”. Note that this can change according to your system configuration (32bits or 64bits), language and Windows Version. 3. The installer will start to copy the necessary files. 4. After installation has completed, a shortcut in user desktop will appear. UM-0909 36 5. Connect USB cable between computer and repeater, keeping the repeater powered off. Usually, drivers will be automatically installed, but depending on Windows version, screen asking for drivers of new device can appear. Drivers can be found in application folder: C:\Program Files (x86)\FiplexControlSoftware\drivers”. 6. Turn on the Repeater BE SURE THAT “TO MOBILE” AND “TO BASE” PORTS ARE PROPERLY LOADED EITHER WITH 50 OHMS DUMMY LOADS, OR RADIATING SYSTEM. 7. Execute the Fiplex Control Software. Next window will appear: UM-0909 37 User interface has the following controls: Scan Devices Button: refresh the available COM ports and identify Fiplex devices Connection Button: connect / disconnect software from repeater List of available devices: below two buttons, is placed a dropdown list that shows all available COM ports. Available COM ports not related to Fiplex devices will be shown with its number and “Unknown device” label. COM ports related to Fiplex devices will show a device description. Embedded Web browser: graphical area where configuration and monitoring parameters will be shown. File menu: contains menus to save repeater configuration to a file and load configuration from file to repeater. NOTE: if Fiplex Repeater is not turned on, related COM port will appear as “Unknown device” 8. Click “Scan Devices” UM-0909 38 Now, the Fiplex unit is shown in the list of available devices, and connection button is enabled. NOTE: Fiplex repeater could not appear in list, if COM port number is higher than COM16, depending on Windows version. COM port number can be forced to arbitrary number (below COM16) through Device Administrator. In order to change COM number, click “Properties” pop-up menu: Click “Advanced Options” UM-0909 39 Change COM port number 9. Click “Connect”. Fiplex Control Software window will be automatically maximized, and it will show the configuration screen described in previous sections. UM-0909 40 10. Once system is configured, user can disconnect software using connection button, now labelled “Disconnect”. Initial window will be shown. If repeater is disconnected or turned off, while Fiplex Control Software is connected to device, software will go back to initial window. Moreover, if some communication problem occurs while device is monitored, the software will go back to initial state as well. 11. Remote unit can be controlled through USB port. In this case, Fiplex Control Software will show that connected device is a remote unit. After click on “Connect” button, program will show only remote configuration and monitoring parameters, with same graphical interface described in previous sections: UM-0909 41 UM-0909 42
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 46 Language : es-AR Tagged PDF : Yes Title : TETRA User's Manual Author : gponcedeleon Creator : Microsoft® Word 2013 Create Date : 2017:10:20 17:11:48-03:00 Modify Date : 2017:10:20 17:11:48-03:00 Producer : Microsoft® Word 2013EXIF Metadata provided by EXIF.tools