Fu Hsing A28WG014 Electronic Keypad Deadbolt with Remote User Manual
Taiwan Fu Hsing Industrial Co., Ltd. Electronic Keypad Deadbolt with Remote Users Manual
Fu Hsing >
Users Manual
G00-KPD0LAC13 Rev. 18/04-00 USER GUIDE OVERVIEW OF THE LOCKSET 1 LED INDICATOR 1. Used to unlock the lockset. 1. Protects the batteries from unexpected damage. CARD OR 7 [SET] BUTTON 2 KEYPAD LED INDICATOR 1. Press set button for 1 second to enter programming mode. 2. Please refer to 2 - 2 for more information about programming mode. 1. Unlocks the lockset by entering a valid user code. 2. Programs the lockset by entering a valid programming code in the programming mode. 9 RFID CARD 6 BATTERY COVER 1. Green light: Code entered is valid. 2. Red light: Code entered is invalid / Under setup mode. 3. Yellow light: Low battery warning. *All batteries should be replaced if yellow light flashes. 1. Hold the Lock Button for over 3 seconds to turn on LED. LOCK BUTTON 3 LOCK BUTTON 1. Press 1. Used to lock the lockset . button to lock the lockset. 4 CANCEL BUTTON 1. Press UNLOCK BUTTON button to cancel any input. 5 KEY OVERRIDE 1. Lock or unlock the lockset by a valid key. 1. Used to unlock the lockset . INTERIOR THUMBTURN 1. Used to lock or unlock the lockset manually. HOW TO LOCK / UNLOCK / PROGRAM THE LOCKSET 1 HOW TO LOCK / UNLOCK THE LOCKSET To lock To unlock Press button to lock. ( The Green LED will light up and a short beep will sound ) Enter valid User Code or Programming Code to unlock. Use a mechanical key to lock. Use a mechanical key to unlock. Use a Remote Control to lock (For remote control version only) Use a Remote Control to unlock (For remote control version only) Use a valid RFID Card to unlock (For RFID version only) The screen is temporarily disabled after 4 consecutive incorrect entries. 2 HOW TO PROGRAM THE LOCKSET BASIC SETTINGS Change Programming Code Add a User Code(S) ・Programming Code can be used to program or unlock the lockset. ・The default Programming Code is “123456”. Press [SET] for 1 second. Programming Code (6 digits) New Programming Code (6 digits) ・Add one or more User Codes / Card / Remote Control. ・User Code capacity: 10 sets (4-6 digits) / Card / Remote Control capacity : 10 sets. New User Code (4-6 digits) OR Press [SET] for 1 second. Programming Code (6 digits) OR Delete Individual User / Single- ・Delete INDIVIDUAL User Code / Card / Remote Control. use User Code(S) User Code (4-6 Digits) OR Press [SET] for 1 second. Programming Code (6 digits) OR Delete ALL User Codes ・Delete ALL User Codes at once. Delete All RFID Cards / Remote ・Delete ALL RFID Cards / Remote Controls. Controls At Once Press [SET] for 1 second. Programming Code (6 digits) Press [SET] for 1 second. Programming Code (6 digits) Press and hold C ( for over 3 seconds ) Press and hold C ( for over 3 seconds ) ADVANCED SETTINGS Add Single-use User Code(S) / Card / Remote Control ・The Single-use User Code / Card / Remote Control can be used for only one successful entry and will be Invalid when the lockset is locked again. ・The Auto-lock should be activated, so the door is locked when the single-use user leaves the building. ・Single-use User Code capacity: 5 sets (4 digits). / Card / Remote Control : 10 sets. Single-use User Code (4 digits) OR Press [SET] for 1 second. Programming Code (6 digits) OR Vacation Mode Button Sound ・Enable Vacation Mode will temporarily disable ALL User Codes. Only Programming Code or mechanical key can open the lock. Press [SET] for 1 second. Double Authorization Mode Programming Code (6 digits) ・Default Auto-lock Mode : off . Press [SET] for 1 second. Auto-lock Delay Timer ・Default Button Sound : on . Press [SET] for 1 second. Auto-lock Mode Programming Code (6 digits) Programming Code (6 digits) ・Default Auto-lock delay timer : 10 seconds. ・Auto-lock range : 10 – 99 seconds. Press [SET] for 1 second. Programming Code (6 digits) ・When Double Authorization Mode is turned on, both User Code and RFID Card / Remote Control, must be authenticated to unlock the lockset. Press [SET] for 1 second. Programming Code (6 digits) ・The lockset will exit the programming mode and resume to the stand-by status if no input is made in 10 seconds. ・3 Beeps means something was entered incorrectly. Please redo the step again. Turn On Turn Off Turn On Turn Off Turn On Turn Off Enter New Amount (10 - 99) Turn On Turn Off 3 RESTORE TO FACTORY SETTINGS AA Press and hold SET button while inserting the battery back. Hold the set button until long beep over. AA AA AA AA AA AA Remove one battery AA AA DECLARATIONS AND SAFETY STATEMENTS FEDERAL COMMUNICATIONS COMMISSION STATEMENT 1. This will erase all stored information, including bolt direction 2. Please re-enter the default Programming Code to set up the lock after restoring to factory settings. TROUBLESHOOTING IC REGULATIONS This device complies with Industry Canada licence-exempt RSS standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. 1 INSTALLATION QUESTIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). ANSWERS A. The latch does not operate correctly after installation. 1. Check center of strike hole for alignment with latch hole on the door to ensure free movement of the latch bolt. 2. Make sure the torque blade is properly inserted(in the horizontal position) in the latch drive. 3. Make sure the bolt direction has been set up following installation. Refer to installation guide. B. A bump is felt while turning the thumbturn or the key? 1. Execute lock & unlock function to allow the motor to reposition itself. 2 OPERATION QUESTIONS ANSWERS A. Keypad does not respond at all. 1. Check to see if the batteries are correctly-installed. 2. Check to see if the Yellow LED is flashing. If the light is flashing, replace the batteries with new ones. 3. Make sure the cable is well-connected to the port. B. Cannot change programming code. 1. Complete the ” CHANGE PROGRAMMING CODE ” process by inputting codes within 10 seconds. 2. Make sure you have entered the new programming code correctly (6 digits ) . C. Can not delete all user codes. Access code list Do not pass your Programming Code to anyone else. 1. Do not share the programming code with anyone else. 2. Keep a written copy of all vaild user codes in a safe place. ( You may use the table below to record your information) 3. The memory capacity for user codes is 10 sets. 4. It is STRONGLY recommended you change all codes if any security information in the table is lost. 1. Make sure all code inputting processes are completed within 10 seconds. 2. Make sure you have entered the correct programming code. 3. The C button should be pressed for over 3 seconds. Programming code Name D. Cannot add a new user code. 1. Make sure all code inputting processes are completed within 10 seconds. 2. Make sure you have entered the correct programming code. 3. The new user code will not be accepted if 10 user codes are already stored in the memory. E. The lockset can not be unlocked 1. Make sure you have entered the correct user code. 2. Check to see if the Yellow LED is flashing. If the light is flashing, replace the batteries with new ones. by keypad. 3. Make sure the strike plate is installed correctly if you see the latch jammed. F. Unable to reset the lockset. 1. Refer to ” RESTORE FACTORY SETTING ” section 2 - 3 and make sure all steps are followed correctly. 2. Check to see if the Yellow LED is flashing. If the light is flashing, replace the batteries with new ones. G. Red LED light is still on after setting is completed. 1. Check whether the【SET】button is jammed. 2. Re-install the batteries. H. ”Auto lock” function does not work. 1. Check to see if the Yellow LED is flashing. If the light is flashing, replace the batteries with new ones. I. Yellow LED light keeps flashing. 1. The batteries are getting low, please reinstall four new batteries for best performance (Alkaline batteries only ). J. What should I do if a wrong code 1. Press C button once and continue to enter code according to normal procedures. was entered? K. How to illuminate the keypad? 1. Press any button on the keypad to initiate LED backlight. If the lock appears to be damaged or does not operate properly, please contact customer service for further assistance. User Code
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2018:04:23 15:36:54+08:00 Metadata Date : 2018:04:23 15:36:55+08:00 Modify Date : 2018:04:23 15:36:55+08:00 Creator Tool : Adobe Illustrator CS6 (Macintosh) Thumbnail Width : 256 Thumbnail Height : 188 Thumbnail Format : JPEG Thumbnail Image : (Binary data 11657 bytes, use -b option to extract) Instance ID : uuid:c17e91bd-6f1f-6943-94cc-82973c74597f Original Document ID : xmp.did:8AD96A8E1B5EE111B334FF5301E28B9B Document ID : xmp.did:0880117407206811822AF64DE77B19F4 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:0480117407206811822AF64DE77B19F4 Derived From Document ID : xmp.did:0480117407206811822AF64DE77B19F4 Derived From Original Document ID: xmp.did:8AD96A8E1B5EE111B334FF5301E28B9B Derived From Rendition Class : default History Action : converted, saved, saved History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh), Adobe Illustrator CS6 (Macintosh), Adobe Illustrator CS6 (Macintosh) History Changed : /, /, / History When : 2013:05:14 08:02:38+08:00, 2013:05:14 08:39:04+08:00, 2018:04:23 15:36:46+08:00 History Instance ID : xmp.iid:0180117407206811822ADB728C23915C, xmp.iid:0880117407206811822AF64DE77B19F4 Format : application/pdf Title : KPD小型化內側英文 Producer : Adobe PDF library 10.01 Trapped : False N Pages : 1 Has Visible Transparency : False Has Visible Overprint : True Max Page Size W : 296.999959 Max Page Size H : 420.000031 Max Page Size Unit : Millimeters Font Name : Times-Bold, KozGoPr6N-Regular, AdobeMingStd-Light, LiGothicMed, LiSungLight, HelveticaNeue-BoldCond, HelveticaNeueLTStd-MdCn, HelveticaNeueLTStd-HvCn, HelveticaNeueLTStd-Bd, ArialMT, Arial-BoldMT, Arial-Black, EuropeanPi-One, Formata-Condensed, DFHei-Md Font Family : Times, 小塚ゴシック Pr6N, Adobe 明體 Std, 蘋果儷中黑, 蘋果儷細宋, Helvetica Neue, Helvetica Neue LT Std, Helvetica Neue LT Std, Helvetica Neue LT Std, Arial, Arial, Arial Black, EuropeanPi, Formata, DFHei Md-HK-BF Font Face : Bold, R, L, 中黑, 細宋, 77 Bold Condensed, 67 Medium Condensed, 87 Heavy Condensed, 75 Bold, Regular, Bold, Regular, Regular, Condensed, Md-HK-BF Font Type : TrueType, Open Type, Open Type, TrueType, TrueType, Type 1, Open Type, Open Type, Open Type, TrueType, Open Type, Open Type, TrueType, Type 1, Unknown Font Version : 10.0d1e3, Version 6.014;PS 6.005;hotconv 1.0.67;makeotf.lib2.5.33168, Version 6.007;PS 6.001;hotconv 1.0.67;makeotf.lib2.5.33168, 6.1d3e1, 6.1d1e2, 001.000, OTF 1.029;PS 001.000;Core 1.0.33;makeotf.lib1.4.1585, OTF 1.029;PS 001.000;Core 1.0.33;makeotf.lib1.4.1585, OTF 1.029;PS 001.102;Core 1.0.33;makeotf.lib1.4.1585, Version 1.10, Version 5.01.2x, Version 5.00.1x, Version 001.000, 001.000, 10.0d5e1 Font Composite : False, False, False, False, False, False, False, False, False, False, False, False, False, False, False Font File Name : Times.dfont, KozGoPr6N-Regular.otf, AdobeMingStd-Light.otf, Apple LiGothic Medium 拷貝.ttf, Apple LiSung Light.ttf, HelveNeuBolCon; Helvetica Neue Condensed, HelveticaNeueLTStd-MdCn.otf, HelveticaNeueLTStd-HvCn.otf, HelveticaNeueLTStd-Bd.otf, Arial., Arial Bold.ttf, Arial Black.ttf, European_Pi_1.ttf, FormaCon; Formata, STHeiti Light.ttc Plate Names : Cyan, Magenta, Yellow, Black, K 100, PANTONE 485 C Swatch Group Name : 預設色票群組 Swatch Group Type : 0 Swatch Colorant Swatch Name : AutoCAD Color 1, AutoCAD Color, PANTONE 151 C, Bars Color, K 100, PANTONE 485 C, C=0 M=0 Y=0 K=100, K100, PANTONE Warm Red CVC, PANTONE Blue 072 C, AutoCAD Color 2, AutoCAD Color 8, AutoCAD Color 3, PANTONE Process Cyan CVC-1 Swatch Colorant Type : PROCESS, PROCESS, SPOT, SPOT, SPOT, SPOT, PROCESS, PROCESS, SPOT, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS Swatch Colorant Tint : 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000 Swatch Colorant Mode : CMYK, CMYK, Lab, CMYK, CMYK, Lab, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK Swatch Colorant Cyan : 0.000000, 92.971703, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 57.424301, 57.424301, 92.971703, 100.000000 Swatch Colorant Magenta : 96.020401, 87.972801, 0.000000, 0.000000, 0.000000, 0.000000, 79.000000, 0.000000, 48.407700, 48.407700, 87.972801, 0.000000 Swatch Colorant Yellow : 94.604401, 89.019600, 0.000000, 0.000000, 0.000000, 0.000000, 91.000000, 0.000000, 45.474899, 45.474899, 89.019600, 0.000000 Swatch Colorant Black : 0.000000, 79.998497, 100.000000, 100.000000, 100.000000, 100.000000, 0.000000, 100.000000, 0.000000, 0.000000, 79.998497, 0.000000 Swatch Colorant L : 69.803902, 49.803898 Swatch Colorant A : 47, 69 Swatch Colorant B : 79, 55 Slug Family : Apple LiSung Slug Version : 3.5 Slug Outline File Size : 0 Slug Kerning Checksum : 0 Slug Foundry : Apple Computer Slug Font Kind : TrueType Slug Checksum : 3238759822 Slug Post Script Name : LiSungLight Slug Font Sense 12 Checksum : 3238759822 Page Count : 2 Creator : Adobe Illustrator(R) 16.0 For : zoe_su , Bounding Box : -5390 -376 -1928 2160 Container Version : 11 Creator Version : 16EXIF Metadata provided by EXIF.tools