High Flying Electronics Technology HF-Z100C ZigBee Module User Manual

High-Flying Electronics Technology Co., Ltd. ZigBee Module

User Manual

User Manual 1 OF 7 High-Flying Electronics Technology Co., Ltd. Model :HF-Z100C Design Hewei 2014-03-12 Description : ZigBee Module Verify Wanghuanming 2014-03-12 Document No.: F20140312 Version : 1.0 Approve Wenqing 2014-03-12 Release Date: 2014-03-12 Pagination: Of 5 Specification
User Manual 2 OF 7 1 .Photo 2 Product Description HF-Z100C HF-Z100C is a wireless communication device based on the latest IEEE802.15.4 standard and Zigbee wireless communication protocol. When compared with the Bluetooth technology, it comes with the advantages of low complexity, low power, low cost, self-organizing, and so on. Since it is based on IEEE802.15.4 standard, it allows smooth connections among thousands of tiny sensors that demand information exchange through radio waves between any two sensors, with very little energy and high communication efficiency. Application HF-Z100C module is widely applied to commercial building automation, home automation control (including smart lighting, sensor, gateway etc that is used in smart home) and instrument control as the focus. Commercial building can be completed automatically controlled through HF-Z100C, administrators can effectively manage air conditioning, lighting, fire detection systems, the switch control system, leading to cost reduction of energy consumption, as well as labor cost. For the consumer, if the family has installed HF-Z100C module system can easily monitor the overall operation of the home, effectively control electricity, water, gas usage outside, they can have security features, for example, to install a wireless home sensors to monitor a variety of different situations, once the investigation into the abnormal automatically issue a warning.
User Manual 3 OF 7 3. Product Features:  Low power consumption in low-power standby mode, the standby time is more than 10 times the Bluetooth communication devices  Low cost, by dramatically simplifying the protocol (less than Bluetooth 1/10), reducing the requirement for communication controller, suitable for large-scale construction applications  Variable data rates, HF-Z100C works in the 2.4GHz band, providing 250 kbps raw data rate using standard mode, or up to 2Mbps using Marvell proprietary mode, to meet the application needs of various rates towards data transmission.  close quarters, the transmission range is generally between 10 ~ 100m indoor, and up to 2km outdoor. After increasing the transmission power, the distance can be further increased. This is the distance between adjacent nodes. If the route and through the inter-node communication relay transmission distance will be farther  short delay, faster response speed HF-Z100C, generally from sleep into working condition just 15ms, nodes are connected into the network just 30ms, further saving energy. Comparison, Bluetooth requires 3 ~ 10s, WiFi need 3 s  high security, HF-Z100C provides three security modes, including no security settings, using access control lists (Access Control List, ACL) to prevent illegal access to data and the use of the Advanced Encryption Standard (AES 128) symmetric password to flexibly determine their security attributes.  wide range of applications for home and building networks, industrial control, wireless meter reading, medical equipment, agricultural control and other occasions
User Manual 4 OF 7 4.Product Specification Model HF-Z100C Chipset 88MZ100 Wireless Standard IEEE802.15.4 Radio Data Rate 250Kbps Channel 16 Sensitivity @250kbps（dBm） -104dBm(Min) Frequency Range 2.405~2.480GHz Interface Refer to Section 5 Antenna Type Onboard 2dBi（Max）PCB antenna Input Voltage（V) DVDD 2.0V-3.6V(Typical DC 3.3V) Max Current on 9dBm TX power（mA) ＜60mA Sleep Current（uA) ＜3uA Communication Distance Indoor≥ 50m,Outdoor≥ 300m Environment Operating Temperature: -40℃~85℃ Storage Temperature: -40℃~125℃ Operating Humidity: 10%~90% non-condensing Storage Humidity: 10%~90% non-condensing Dimensions (mm) 22.2mm*15.4mm*3.0mm
User Manual 5 OF 7 5. Interface Pin Definition The module pin reference definition is referred to the table like below. The GPIO assignment is ONLY reference for the full application on lighting. For some specified application, please refer to the PINMUX of 88MZ100 datasheet for the flexible GPIO assignment. Pin Number Signal Assignment Reference GPIO Assignment for Lighting Pin1-2 GND Ground Pin3 GPIO12 PWM output-1(Timer1) Pin4 GPIO13 PWM output-2(Timer1) Pin5 GPIO14 SWD Clock Pin6 GPIO15 SWD Data Pin7 GPIO16 IIC SDA Pin8 VIO The IO power Pin9 GPIO17 IIC CLK Pin10 GPIO18 PWM output-3(Timer1) Pin11-13 GND Ground Pin14 GPIO21 UART2 TXD Pin15 GPIO22 UART2 RXD Pin16 GPIO23 PWM output-4(Timer1) Pin17 GND Ground Pin18 VBAT The main power Pin19 GND Ground Pin20 GPIO29 Reserve Pin21 GPIO28 Reserve Pin22 GND Ground Pin23 RESET_N The reset signal Pin24 GPIO4 ADCx3 or ADCx1 and Wakeup INTx2 Pin25 GPIO5 Pin26 GPIO6 Pin27 GND Ground Pin28 The under GND Ground
User Manual 6 OF 7 6. FCC Statement: Federal Communication Commission Interference Statement FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. USER MANUAL OF THE END PRODUCT: In the user manual of the end product, the end user has to be informed that the equipment complies with FCC radio-frequency exposure guidelines set forth for an uncontrolled environment. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the user manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following" Contains TX FCC ID: 2ACSV-HF-Z100C ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
User Manual 7 OF 7 IC warning statements: -English Warning Statement: “This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device." -French Warning Statement: “Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement." .

Navigation menu