Hyundai Digital Technology PANSAT330A Digital Satellite Receiver User Manual Manual 330A
Hyundai Digital Technology Co., Ltd. Digital Satellite Receiver Manual 330A
Users Manual
FCC ID:PZ8PANSAT330A Report No: E01.1105.FCC.451N Test Date: February 18~21, 2002 Appendix F. ETL Inc. 371-51 Gasan-Dong, Geumcheon-Gu, Seoul, 153-023, Korea User’s Manual Hyundai Digital Technology Co., Ltd. Digital Satellite Receiver Model :PANSAT 330A 1 of 1 1. Introduction 1.1. Overview 1.2. Main Features 2. Safety/Precautions 2.1. Safety 2.2. Precautions 3. Check Point before Use 3.1. Accessories 3.2. The Satellite dish 4. Controls/Functions 4.1. Front Panel 4.2. Rear Panel 4.3. Remote Controller 5. Using Remote Controller 5.1. Batteries 5.2. Range Of Operation 12 6. How to Connect 14 7. Operation 7.1. Getting Started 7.2. Channel Editing 7.3. System Parameters 7.4. Transponder 7.5. Factory Set 7.6. Other Function on Remote Control 16 8. Trouble Shooting 65 9. Specifications 66 DiSEqC is a trademark of EUTELSAT. This satellite receiver is designed for using digital free-to-air channel reception. Enjoy the rich choice of more than 4,000 different channels, broadcasting a large range of culture, sports, cinema, news, events, etc. This receiver is a technical masterpiece, assembled with the highest qualified electronic parts. Fully compliant with MPEG-2 and DVB standards User friendly operating Menu and On-Screen Graphic Menu Easy to use EPG(Electronic Program Guide) on screen Age protection lock function Tele-text encoding Manual PID control Software downloading via RS-232C connector DiSEqC 1.2 compatible Be sure to read the user's manual before starting the operation of the unit. Do not touch the power cord with wet hands as it may cause electric shock. Never open the cover. It is very dangerous to touch the inside of the unit due to possible electric shock. Place the unit in a well ventilated and no-heat environment. When you do not use this unit for a long time, make sure that power cord is pulled out from the outlet. Also do not use a damaged power cord as it may cause fire or electric shock. A professional installation is required. If reception is interrupted, contact your local service centre. When installing the unit Install the unit horizontally. An uneven installation may cause the unit to be damaged. Do not put heavy items such as a TV on the unit. That may cause the unit to be damaged. Do not install the unit: Moving the unit to a hot area from a cold one will cause condensation. Do not operate the unit for one or two hours or until it has dried completely. Where it is subject to vibrations Where it is exposed to direct sunlight Where there is humidity Where the temperature is too high or too low. Where there is no ventilation Accessories of the Unit Remote control : 1 User's manual : 1 QZ- GHI ABC MNO TUV WXY INFO ua an sm Us DEF JKL PRS AUDIO GUIDE CH.LIST CH VOL MENU VOL CH RECALL TV/RADIO AUX IN EXIT SLEEP TV/SAT Batteries (AAA type) : 2 If any accessories listed above are missing, contact the sales representative where you purchased this unit. Your dish should be properly installed and azimuth and elevation must be precisely set up. This unit is working with DiSEqC 1.2 on a compatible antenna positioner. Ask your dealer for information. Power To switch the receiver in “standby” mode or in power on mode. Standby/Power on Indication light Turn on red while in the “standby” mode and turn off the red light while in the power on mode. Remote Sensor Receives the infrared signal from remote control. Channel Display(4 Digit) - When you connect the power line of the receiver, the current time is displayed. - After programming, the program number is displayed. Menu To launch or terminate the menu application. Select To activate a highlighted item or go to next level on hypertext menu or confirm the user s action. Vol. / To adjust the volume level or change the value of an item with preprogrammed values. The Key can be used as a backspace to cancel the numerical input. CH. / To change channel or cursor position on the application screen. No. Name Connector Function 1. TV ANT IN IEC 169-2 female Input from terrestrial antenna. 2. RF OUT UHF 3-4 IEC 169-2 male Output to TV. 3. AUDIO L RCA cinch Left audio output. 4. AUDIO R RCA cinch Right audio output. 5. VIDEO RCA cinch Composite video output. 6. Digital Audio RCA cinch Digital Audio Output 7. S-VHS 8. RS-232C DB-9 Low speed serial port. 9. LNB INPUT IEC 169-24 female IF input from LNB to digital tuner. 10. LOOP OUT IEC 169-24 female IF loop-through output from Output to VCR or TV. digital tuner. POWER : To switch into ‘standby’ or ‘power on’ mode. QZ- ABC GHI JKL MNO PRS TUV WXY INFO MUTE : To turn the sound on/off. DEF Numeric Keys(0-9) : To select channels and input of channel numbers or characters. AUDIO INFO. : To display the information of the current channel. GUIDE CH.LIST CH VOL MENU AUDIO : To change the audio track, stereomono mode. VOL CH RECALL TV/RADIO AUX IN EXIT GUIDE : (EPG : Electronic Program Guide) To watch program information. Press once more to return to normal mode. SLEEP TV/SAT CH LIST : To watch the channel list. Press to confirm or press EXIT to return to previous chosen channel. Up & Down To change the value of a selected item with preprogrammed values in menu. Left & Right To move the cursor up and down in menu. can be used as a backspace to cancel the numerical input. QZ- ABC DEF GHI JKL MNO PRS TUV WXY INFO ENTER : To select an item or to confirm a menu. Pause function. MENU : To enter/exit the main menu. AUDIO GUIDE CH.LIST EXIT : To return to previous status or menu. CH VOL MENU VOL CH RECALL TV/RADIO AUX IN RECALL : To return to the previous chosen channel. EXIT SLEEP : To switch off the receiver automatically after between 30 and 150 minutes. SLEEP TV/SAT TV/RADIO : To switch between the TV and radio channels. AUX IN : To select the output mode of scart connector. If your receiver has no SCART in the rear panel, this key may not work. TV/SAT : To toggle the TV output source between the satellite input and UHF/VHF antenna input. If your receiver has no 'TV ANT IN' terminal in the rear panel, this key may not work. 10 QZ- ABC GHI JKL MNO PRS TUV WXY INFO BLUE : To delete a channel from the Channel List menu. To show extended program information in the EPG menu. To see Teletext Service Data. DEF IVORY : To add a new channel to the Channel List menu. AUDIO ORANGE : To see variant channel lists for user's convenience in the Channel List menu. GUIDE CH.LIST CH VOL MENU RED : To setup favorite channel lists in the Channel List menu. VOL CH RECALL TV/RADIO AUX IN EXIT GREEN : To lock channel in the Channel List menu. To show current/next program information in the EPG menu. SLEEP TV/SAT YELLOW : To move a channel to other position in the Channel List menu. To show program schedule information in the EPG menu. 11 How to insert a battery When to replace a battery How to replace a battery Accident prevention 12 The remote controller can be detected by the receiver within an angle of 30 degrees to the left or right. The transmission distance of the remote control is 7m in direct line of sight. Notes When the remote control is not operative Replace batteries with new ones and check AC power plug on the receiver. Abnormal operation Disturbance from peripheral devices might occur. Ensure that other products which might cause interference are placed further away from the receiver. Notes for handling If exposed to heat or water, the main body and the remote control may be damaged, so be careful. 13 14 15 After your receiver is powered up, proceed with installation as follows: Menu Language Setting When you plug in AC power, the following will be displayed on the front. Press POWER on remocon, the LED number will be displayed as follows; Press MENU key and position cursor on 'Language' column with Select language you want with or or Screen Main Menu System Parameters Installation Language English Note : Languages displayed in 'Language' column are supported by your receiver. 16 2 Help If you want to know how to use current part in the menu, use 'help' function. Select a content in the menu. For example, if you want to know about the installation menu, select installation. Screen Main Menu System Parameters Installation Language English -Next, Press INFO. Then you can see the help window of the selected content. Screen Satellite Setting Since your receiver has the basic data of most satellites and channels, you can receive programs just by plugging in. But, according to the status of your antenna setup, you may have to modify the basic data of satellites and / or channels. When you need to modify the data, proceed as follows ; 17 Press MENU key and position the cursor on Installation column with and press or Screen Main Menu System Parameters Installation Language English -Next, By using or , select ‘LNB Configuration’ and press Screen Installation LNB Configuration Antenna Setup Satellite Scan TP Edit/Scan Factory Set -Next, -Prev. Note : Enter 4-Digit password if need arise. The default password is ‘0000’ Select the Satellite you want to add with or Screen LNB Configuration Amos AsiaSat 2 Thor Position PAS 4 High L.O. AsiaSat 2 Low L.O. 0 GHz USER1 Power ON USER2 0/22KHz 0 KHz USER3 DiSEqC ---- USER4 L -Page Up/Dn, -Edit 18 000.0 5,150 GHz and press or If you press , the selected Satellite will be added and the cursor will move to right window for detailed installation. Note : If you just want to edit the data of the satellite which is already contained in the receiver, press after you select the satellite. Select item you want to edit with ter. or and change each parame- - Position : When necessary, set the position(longitude) of the satellite with the numeric keys. - High L.O. / Low L.O. : Enter LNB oscillator frequency with numeric keys. - Power : Set LNB power ON or OFF with or If you set LNB type Ocs C-band you can set power ON, 14V, 18V or OFF. - 0/22KHz : Set the path of 0/22KHz switch box with or - DiseqC : Set the feature of DiSEqC box by pressing If you do not use the switch box, set as “- - - ” . Note : When you change each parameter, you need to know exact parameter of LNB to modify L.O.(local oscillator) frequency. Note : When you change each parameter, you need to understand environment of connecting the receiver and antenna in order for you to set 22KHz and DiSEqC properly. When necessary, you can change a satellite name as you wish. You can enter alphabetic characters with the numeric keys. For example, if you want to enter 'SAT-1', Press Note : Press for space. After the installation procedure, press EXIT key or MENU key to store your entered data. 19 4 Antenna Setup You need to position your antenna correctly for reception of the best signal. Press MENU key. Select ‘Installation’ with or , and press Screen Installation LNB Configuration Antenna Setup Satellite Scan TP Edit/Scan DiSEqC[UFO] Setup Factory Set On Air Download -Next, -Prev. Select ‘Antenna Setup’ with or and press Screen Antenna Setup Tuner Lock 3/4 FEC Level Qual. 47% Quality 28,123 MSPS OFF Move/Save Stop Set Limit Disable My longitude 120.0 E My latitude 56.0 N -Main, E -Prev. Indicating selected satellite signal strength level Indicating signal to noise ratio Select the satellite you want with Press Horizontal-18V 98% Level AsiaSat 2 [24] 4,000 GHz Motor/Goto 0 or to move to TP section and select the TP you want with or When the satellite and the TP are selected, you can check the reception status of the satellite signal. If the reception signal status is bad, adjust antenna to get the following result. 20 Tuner Lock FEC 1/2, 2/3, 3/4, 5/6 or 7/8 Level over 30% Quality over 10% DiSEqC 1.2 Positioner Setting If you want to use an antenna positioner compatible with DiSEqC 1.2, please do the following : - Motor / Goto 0 Determine the kind of Motor & whether or not controlling it by using or On Off Using DiSEqC Motor. Not using DiSEqC Motor. STAB Using the specific Motor supplied by Stab company. Determine the longitude of the satellite on LNB Configuration Menu. If the longitude of the satellite on LNB Configuration Menu is set, user must input the longitude about your position at present If you press , DiSEqc Motor will move toward Zero Equator. - Move / Save : Select West/East direction with or Move your antenna to west direction. Move your antenna to east direction. Store the position of your antenna. - Set Limit : Select limit of your antenna movement to east/west direction and press Note : This may be necessary to protect your antenna from any possible collision between your antenna and certain obstacles nearby it. - My longitude / My latitude You can use this item when STAB is set on 'Motor/Goto 0'. Determine your longitude & latitude at present. 'East/West' is changed by using or 21 5 Satellite Scan After finishing ‘Antenna Setup’, execute a ‘Satellite Scan’. Then you can get all channels in the pre-programmed TPs. This function can also be used to get the latest channel data while receiver is in use. Through this function, the receiver searches for all the available channels and saves them in the memory. Press MENU key. or Select ‘Installation’ with Select ‘Satellite Scan’ with , and press or , and press Screen Installation LNB Configuration Antenna Setup Satellite Scan TP Edit/Scan Factory Set -Next, -Prev. Select ‘Scan Mode’ with or Select the scan mode you want with Select the satellite name you want with Screen Satellite Scan Scan Mode Free+Scrambled Satellite Name -Select, -Main, -Prev. 22 AsiaSat 2 or or If you press , the selected satellites will be scanned. Screen Satellite Scan TV: Good Scanning:10% Radio: 33 34 SATLINK 972 2 APTN1 + 442074 17 18 DW 9 RDP ANTENA 1 35 36 37 38 NMTV Guangdong 2 Hunan 2 Hubei 1 19 20 21 22 RDP ESPECIAL NN ¥xÆWaN¥<< TWN ¥@uØ1/2Auø USA 39 Hubei 2 AsiaSat 2 84% [4] 3,720 GHz Hor. 4,420 -Select, M -Main, E -Prev. While scanning, you can see the following menu on the screen. Screen Satellite Scan TV: 33 34 35 36 37 38 39 Bad 1% 39 Scanning:10% Radio: 22 17 SATLINK 972 2 DW 9 Satellite scan is done. 18 APTN1 + 442074 RDP ANTENA 1 NMTV Press 19Key.RDP ESPECIAL 20 Guangdong 2 NN 21 Hunan 2 ¥xÆWaN¥<< TWN 22 Hubei 1 ¥@uØ1/2Auø USA Hubei 2 AsiaSat 2 -Page Up/Down, [28] 3,960 GHz Hor. 30,000 -Watch, M / E -Prev. After the scanning process, the first channel of the last scanned TP will be displayed on the back screen. Press to finish the process. Then select a channel and press watch a program or press MENU key or EXIT key. to Note : Now you have completed all steps needed for watching programs. If you could not see the program after finishing these procedures, please contact your engineer or representative. 23 6 Select Channel You can change the current channel to any other channel you want. If you do not know the channel name, or you want to select a channel at random, you can navigate between channels with or (CH. Up/Down) till you find the channel you want. If you know the channel number, enter the number and wait 5 seconds for the channel to change. If you know the channel name, press CH LIST key then channel list will pop-up. Screen TV Channel List AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well All List Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -EXIT, 0 ~ 9 -Move In the right section, detailed information of the selected channel will be displayed.(Name of satellite, frequency, symbol rate, etc.) Select the channel you want with (page up/down). (scroll up/down) or When the scroll bar is positioned on the channel you want to see, press 24 7 Volume Control While you are watching a program, press the current channel. or to control volume of Note : You can configure volume of each channel differently. Screen When necessary, press MUTE key to remove the sound of the program temporarily. Then, your receiver goes into mute condition and the volume bar will become red. Press MUTE key again to turn the sound on. 25 1 Favorite Channel You can set up favorite channel lists as you want. For example, if you want to set favorite channel lists as following. Favorite1 : 7 DWtv, 6 Hunan1 Favorite2 : 1 Fujian1 Favorite3 : 3 ANHUI TV, 5 Guangdong1 Firstly, set favorite1 channels. Press CH.LIST. Select 'DWtv' channel with or Screen TV Channel List AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well All List Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -EXIT, 0 ~ 9 -Move Press RED. Screen TV Channel List All List Favorite State Fujian 1 Favorite 1 DIGITL VID Favorite 2 ANHUI TV Favorite 3 NMCHTV Guangdong 1 4 Favorite Hunan 1 DWtv Favorite 5 MCM -Select, Rename. -Exit 26 AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well FAV. DEL LOCK ADD MOVE MODE Select favorite1 with or and Press Screen TV Channel List All List Favorite State Fujian 1 Favorite 1 DIGITL VID Favorite 2 ANHUI TV Favorite 3 NMCHTV Guangdong 1 4 Favorite Hunan 1 DWtv Favorite 5 MCM -Select, Rename. AsiaSat 2 [24] 4,847 GHz Horizontal-18V 28,123 MSPS Dban FAV. DEL LOCK ADD MOVE MODE -Exit TV Channel List AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well All List Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -Exit, 0 ~ 9 -Move Do the same for the 'Hunan 1' channel. Screen TV Channel List AsiaSat 2 [20] 3,847 GHz Horizontal-18V 4,420 MSPS Hunan All List Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Page Up/Down, -Watch, 27 -Main, FAV. DEL LOCK ADD MOVE MODE -Exit, 0 ~ 9 -Move Press RED. Screen TV Channel List All List Guangdong 1 4 Favorite Hunan 1 DWtv Favorite 5 MCM -Select, Press Favorite State Fujian 1 Favorite 1 DIGITL VID Favorite 2 ANHUI TV Favorite 3 NMCHTV Rename. AsiaSat 2 [24] 4,847 GHz Horizontal-18V 28,123 MSPS Dban FAV. DEL LOCK ADD MOVE MODE -Exit Screen TV Channel List AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well All List Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -Exit, 0 ~ 9 -Move Favorite1 ~ Favorite5 are default name. Users can rename them for their convenience. If you want to rename 'Favorite1' (for example 'Drama'). Press RED. Screen TV Channel List All List Favorite State Fujian 1 Favorite 1 DIGITL VID Favorite 2 ANHUI TV Favorite 3 NMCHTV Guangdong 1 4 Favorite Hunan 1 DWtv Favorite 5 MCM -Select, Rename. -Exit 28 AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well FAV. DEL LOCK ADD MOVE MODE Select ‘Favorite 1’ with Screen TV Channel List All List Favorite State Fujian 1 Favorite 1 DIGITL VID Favorite 2 ANHUI TV Favorite 3 NMCHTV Guangdong 1 4 Favorite Hunan 1 DWtv Favorite 5 MCM Rename. -Select, AsiaSat 2 [24] 4,847 GHz Horizontal-18V 28,123 MSPS Dban FAV. DEL LOCK ADD MOVE MODE -Exit Press IVORY. Screen TV Channel List All List Favorite State Fujian 1 Favorite 1 DIGITL VID Favorite 2 ANHUI TV Favorite 3 NMCHTV Guangdong 1 4 Favorite Hunan 1 DWtv Favorite 5 MCM -Select, Rename. -Exit 29 AsiaSat 2 [24] 4,830 GHz Horizontal-18V 28,123 MSPS HTV1 FAV. DEL LOCK ADD MOVE MODE Screen TV Channel List All List Press MENU, EXIT or Favorite State Fujian 1 DRAMA DIGITL VID Favorite 2 ANHUI TV Favorite 3 NMCHTV Guangdong 1 4 Favorite Hunan 1 DWtv Favorite 5 MCM -Select, Rename. AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS he Well FAV. DEL LOCK ADD MOVE MODE -Exit to finish the process. You have finished favorite1 channel setting. With similar way, you can set favorite2 ~ favorite5 channel list. You can use these favorite channel lists by using ORANGE key. Refer to the next section for detail. 30 2 Channel List Mode Using this function, you can see variant channel lists which may enable you to edit and select channels more conveniently. Favorite Mode If you have set up favorite channel lists as the previous section, you can use them as following. Press CH.LIST. Screen TV Channel List AsiaSat 2 [20] 3,847 GHz Horizontal-18V 4,420 MSPS Hunan All List Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -Exit, 0 ~ 9 -Move Press ORANGE. Screen TV Channel List AsiaSat 2 All List Channel List Mode [20] 3,847 GHz Fujian 1 Free+Scrambled Horizontal-18V DIGITL VID Favorite 1 4,420 MSPS ANHUI TV Favorite Hunan NMCHTV Satellite AsiaSat 2 Guangdong 1 AB Alphabet FAV. DEL Hunan 1 DWtv MCM -Exit 31 LOCK ADD MOVE MODE You can see 'Channel List Mode' window. Select 'Favorite' with and select 'Favorite1' with or Screen TV Channel List AsiaSat 2 All List Channel List Mode [20] 3,847 GHz Fujian 1 Free+Scrambled Horizontal-18V DIGITL VID Favorite 1 4,420 MSPS ANHUI TV Favorite Hunan NMCHTV Satellite AsiaSat 2 Guangdong 1 AB Alphabet FAV. DEL Hunan 1 LOCK ADD DWtv MCM Press MOVE MODE -Exit Screen TV Channel List AsiaSat 2 [20] 3,847 GHz Horizontal-18V 4,420 MSPS Hunan Favorite 1 Hunan 1 DWtv -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -Exit, 0 ~ 9 -Move You can see only favorite1 channels are listed. With similar way, you can see favorite2 ~ favorite5 channel list. If you want to return to all channel list (all channels of the selected satellite), press ORANGE and select 'Satellite' with and press Screen TV Channel List AB DIGITL VID DWtv Free+Scrambled Favorite Satellite AB AsiaSat 2 [24] 4,000 GHz Horizontal-18V Favorite 1 28,123 MSPS AsiaSat 2 Deutsche Well Channel List Mode Alphabet -Exit 32 FAV. DEL LOCK ADD MOVE MODE Alphabet Mode Using this function, you can see the channel list which have same initial. This function is useful when you search specific channel among the list of thousands channels. For example, if you want to see the channel lists which start with 'D'. Press ORANGE in the channel list and select 'Alphabet' with Screen TV Channel List AsiaSat 2 All List Channel List Mode [20] 3,000 GHz Fujian 1 Free+Scrambled Horizontal-18V DIGITL VID Favorite 1 4,420 MSPS ANHUI TV Favorite Hunan NMCHTV Satellite AsiaSat 2 Guangdong 1 AB Alphabet FAV. DEL Hunan 1 LOCK ADD DWtv MCM Select 'D' with MOVE MODE -Exit Screen TV Channel List AsiaSat 2 All List Channel List Mode [20] 3,000 GHz Fujian 1 Free+Scrambled Horizontal-18V DIGITL VID Favorite 1 4,420 MSPS ANHUI TV Favorite Deutsche Well NMCHTV Satellite AsiaSat 2 Guangdong 1 AB Alphabet FAV. DEL Hunan 1 LOCK ADD DWtv MCM Press MOVE MODE -Exit Screen TV Channel List AB AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well DIGITL VID DWtv -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -Exit, 0 ~ 9 -Move You can see the channel list where all channels have initial 'D'. 33 Free only Mode Press ORANGE in the channel list and select first line with Select 'Free only' with Screen TV Channel List AsiaSat 2 All List Channel List Mode [20] 3,000 GHz Fujian 1 Free+Scrambled Horizontal-18V DIGITL VID Favorite 1 4,420 MSPS ANHUI TV Favorite Hunan NMCHTV Satellite AsiaSat 2 Guangdong 1 AB Alphabet FAV. DEL Hunan 1 DWtv MCM LOCK ADD MOVE MODE -Exit Select 'Favorite' or 'Satellite' or 'Alphabet' and press the selected 'free' channel list. . You can see only Free + Scrambled Mode Press ORANGE in the channel list and select first line with Select 'Free+ Scrambled' with Screen TV Channel List All List Channel List Mode Fujian 1 Free+Scrambled DIGITL VID DRAMA ANHUI TV Favorite NMCHTV Satellite AsiaSat 2 Guangdong 1 AB Alphabet Hunan 1 DWtv MCM -Exit 34 AsiaSat 2 [20] 3,20 GHz Horizontal-18V 4,420 MSPS Dian FAV. DEL LOCK ADD MOVE MODE Select 'Favorite' or 'Satellite' or 'Alphabet' and press selected free and scrambled channel list. . You can see the Screen TV Channel List AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well All List Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -Exit, 0 ~ 9 -Move Note : 'Scrambled' channel can be shown only with CI (Common Interface) model and CAS (Conditional Access System) model. 'Free' channel can be shown with all (FTA(Free To Air) and CI and CAS) model. Satellite Mode By using this function, you can see all channel list of the selected satellite. Press ORANGE and select ‘Satellite’ item with Screen TV Channel List AB DIGITL VID DWtv Free+Scrambled Favorite Satellite AB Alphabet FAV. DEL LOCK ADD MOVE MODE to select a satellite and press Press AsiaSat 2 [24] 4,000 GHz Horizontal-18V Favorite 1 28,123 MSPS AsiaSat 2 Deutsche Well Channel List Mode -Exit 35 3 Lock Channel This menu enables you to prevent children from viewing programs unsuitable for their age. Press CH.LIST and Select the channel you want to lock with or and press GREEN. or Then the selected channel is locked. Screen TV Channel List AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well All List Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -EXIT, 0 ~ 9 -Move Note : If ‘password' window is risen as following picture, enter password with numeric keys (default password is' 0000'). Then you can lock the channel. If you don't want this window, change ‘Parental Control' set up in the ‘System Parameters' menu. Refer to the ‘Parental control' in ‘System parameters' in this manual for detail. Screen TV Channel List AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well All List Fujian 1 NMCHTV RAI Guangdong 1 Hunan 1 MCM DWtv TVE -Page Up/Down, -Watch, 36 -Main, FAV. DEL LOCK ADD MOVE MODE -EXIT, 0 ~ 9 -Move Screen TV Channel List All List Fujian 1 NMCHTV RAI Guangdong 1 Hunan 1 MCM DWtv TVE -Page Up/Down, Press MENU, EXIT or AsiaSat 2 [24] 4,000 GHz Horizontal-18V << Authorized! >> 28,123 MSPS Deutsche Well -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -EXIT, 0 ~ 9 -Move to finish the process. Without entering your password, you cannot watch a locked channel's program. Screen AsiaSat 2 7 DWtv ((( 1/? (( 14:14 In Focus 13:56 ~ 14:26 If you want to cancel the channel lock, go to the channel list and select the channel and press GREEN. 37 4 Channel Order Setting You can organize the number or sequence of the channels. Press CH.LIST. Screen TV Channel List AsiaSat 2 [9] 3,773 GHz Horizontal-18V 5,632 MSPS Reuters Londo All List 17 18 19 20 21 22 23 24 Jiangxi 1 Jiangxi 2 LNTV WNS MEA LON SATLINK 972 2 APTN1 +442074 NMTV Guangdong 1 -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -EXIT, 0 ~ 9 -Move Select the channel you want to move with press YELLOW. or and Screen TV Channel List AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well All List 10 11 12 13 14 15 16 RAI Internati TVE TV5-Asia RTPi uØoH-u1/4Ö¥x CS ªFËê>>Ú¥x ET «DoZ¥x USTV-I oé¥>>¥x JET FAV. DEL LOCK ADD MOVE MODE -Page Up/Down, -Watch, -Main, Move the selected channel with want. -EXIT, 0 ~ 9 -Move or Screen TV Channel List AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well All List 12 11 12 13 14 15 16 RAI Internati RTPi TV5-Asia RTPi uØoH-u1/4Ö¥x CS ªFËê>>Ú¥x ET «DoZ¥x USTV-I oé¥>>¥x JET -Page Up/Down, FAV. DEL LOCK ADD MOVE MODE -Watch, 38 -Main, -EXIT, 0 ~ 9 -Move to the position you Press YELLOW. Screen TV Channel List AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well All List 10 11 12 13 14 15 16 RAI Internati RTPi TVE TV5-Asia uØoH-u1/4Ö¥x CS ªFËê>>Ú¥x ET «DoZ¥x USTV-I oé¥>>¥x JET -Page Up/Down, Press MENU, EXIT or FAV. DEL LOCK ADD MOVE MODE -Watch, -Main, -EXIT, 0 ~ 9 -Move to finish the process. Delete Channel You can delete channels from the channel list. Press CH.LIST and select the channel you want to remove with or Screen TV Channel List AsiaSat 2 [3] 3,713 GHz Horizontal-18V 4,420 MSPS Hubei All List 10 11 12 13 14 15 16 TVE TV5 - Asia Hubei 1 Hubei 2 RAI Internati Fujian 2 Jiangxi 1 Jiangxi 2 -Page Up/Down, -Watch, 39 -Main, FAV. DEL LOCK ADD MOVE MODE / L -Exit, 0 ~ 9 -Move Press BLUE. Note : If ‘password' window is risen as following picture, enter password with numeric keys (default password is' 0000'). Then you can delete the channel. If you don't want this window, change ‘Parental Control' set up in the ‘System Parameters' menu. Refer to the 'Parental control' in System parameters' in this manual for detail. Screen TV Channel List PASSWORD 10 11 12 13 14 15 16 TVE TV5 - Asia Hubei 1 Hubei 2 RAI Internati Fujian 2 Jiangxi 1 Jiangxi 2 ???? -Page Up/Down, -Watch, -Main, AsiaSat 2 [3] 3,713 GHz Horizontal-18V 4,420 MSPS Hubei FAV. DEL LOCK ADD MOVE MODE / L -Exit, 0 ~ 9 -Move Then, you need to confirm the deletion. If you definitely want to delete, press . If not, press EXIT. Screen TV Channel List All List 10 11 12 13 14 15 16 TVE TV5 - Asia Hubei 1 Hubei 2 RAI Internati Fujian 2 Jiangxi 1 Jiangxi 2 AsiaSat 2 Do you want to delete this channel? [3] 3,713 GHz Yes / No Horizontal-18V 4,420 MSPS Hubei -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE / L -Exit, 0 ~ 9 -Move Note: Please be careful when you delete channel(s). Press MENU, EXIT or to finish the process. 40 6 Add Channel Press CH.LIST. Screen TV Channel List AsiaSat 2 [24] 4,000 GHz Horizontal-18V 28,123 MSPS Deutsche Well All List Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Page Up/Down, -Watch, -Main, FAV. DEL LOCK ADD MOVE MODE -EXIT, 0 ~ 9 -Move Press Ivory. Screen TV Channel List Satellite Name AsiaSat 2 TP Frequency [24] 4,000 GHz Polarization Horizontal-18V Symbol Rate 28,123 MSPS CH. Name DWtv Video PID 2305 Audio PID 2306 PCR PID 2304 Select a satellite into which you want to add your new channel. Note : You can only select satellites which you set in ‘Installation’ menu. Move to 'TP Frequency' section (column) by pressing and change frequency with or enter frequency with numeric keys. Note : TP frequency consists of 5 digits ending with GHz. For example : TP Frequency 4.000GHz is 41 Move to 'Polarization' by pressing with or and select Horizontal or Vertical Note : Please check whether LNB Power is ON in ‘Installation’ menu Move to 'Symbol Rate' by pressing with numeric keys. Move to 'CH. Name' by pressing with numeric keys. and enter the Symbol Rate value and enter the alphabetic characters For example : if you want to enter SAT-1, Note : Press for space Move to 'VIDEO PID' by pressing numeric keys. key and enter the proper value with Move to 'AUDIO PID' by pressing numeric keys. key and enter the proper value with Move to 'PCR PID' by pressing 0000~8192 with numeric keys. key and enter the value between Note : The above mentioned TP Frequency, Symbol Rate, VIDEO PID, AUDIO PID, PCR PID are very important for optimal satellite signal reception. We recommend you get professional advice where available. You cannot setup ‘VIDEO PID’ for RADIO channels. 42 1 Setting Age Restrictions This sub-menu allows you to set the age for parental locking and protect children from viewing programs unsuitable for their age. Press MENU key. Press or to select 'System Parameters' and press Screen System Parameters Parental Control System Information Local time/Timer DL Saving No TV Type Press or MULTI Aspect Ratio 4X3 Screen P/S 18/07/2001 16:43 RF Channel -Prev. to select 'Parental Control' and press Screen System Parameters Parental Control PASSWORD System Information ???? Local time/Timer DL Saving TV Type No MULTI Aspect Ratio 4X3 Screen P/S -Prev. 43 18/07/2001 16:43 RF Channel Enter 4-digit password. Note : The default password is '0000' Screen System Parameters Parental Control PASSWORD System Information **** 18/07/2001 16:43 Local time/Timer << Authorized! >> DL Saving No TV Type 4X3 Screen P/S Press or RF Channel MULTI Aspect Ratio -Prev. to select ‘Age Limit’. Screen Parental Control Age Limit None Lock Channel Editing No Lock Installation No New Password ???? Verify Password Personal -Main, Press None 12 15 18 or ???? ***** -Prev. to select age you want. No age limit Without entering password, programs are restricted to those who are over 8 years old. over 12 years old. over 15 years old. over 18 years old. Note : ’Age limit’ can be applicable only for the signal which carries age limit information. 44 2 Security Check You can set SECURITY CHECK to protect your current installation from being changed (location shift, deletion, adding etc.) or modifying of installed data. Press MENU key Press or to select 'System Parameters' and press Press or to select 'Parental Control' and press Enter 4-digit password. Note : The default password is '0000' Press Press Yes No or or to select ‘Lock channel Editing’, or ‘Lock Installation’. to select ‘Yes’, or ‘No’. When you process with ‘Channel Editing’ or ‘Installation’ of Main Menu, your receiver will ask for password. If you enter wrong password, you cannot proceed further. You do not enter password during your processing. Note : Your receiver is pre-set as 'Yes'. Password Changing You can change your password. Press MENU key. Press or to select 'System Parameters' and press Press or to select 'Parental Control' and press Enter 4-digit password. Note : The default password is '0000' Press or to select ‘New Password’. 45 Press numeric numbers to enter new password. Press numeric numbers again to verify the new password. Note : When you forget your new password, please consult the shop where you bought the receiver or the nearest dealer. Personal Information Setting You can enter your personal information, such as your name and address, etc. Press MENU key. Press or to select 'System Parameters' and press Press or to select 'Parental Control' and press Enter 4-digit password. Note : The default password is '0000' Press Press or to select ‘Personal’. numeric numbers to enter new personal information. For example: If you want to enter 'WELCOME', Note : 1. Maximum 32 letters can be entered. 2. Your entered personal information will be displayed on the TV screen as Welcome Window when you power on your receiver. 3. Initial information is ‘ ’. 4. After purchasing the receiver, if information other than that which you entered is displayed, please consult the shop where you bought it. 5. Personal Information does not affect your viewing in any way. 46 5 System Information You can check the current information about your receiver such as receiver’s software and hardware version or manufacturing date. Press MENU key. Press or to select 'System Parameters' and press Screen System Parameters Parental Control System Information Local time/Timer DL Saving No TV Type Press or RF Channel MULTI Aspect Ratio 4X3 Screen P/S dd/mm/yyyy hh:mm -Prev. to select 'System Information' and press Screen System Information Product Name -Main, Pansat 330A Hardware Version 330A - 001 Software Version 330A - 001 Channel List 330A - 001 Last Update Feb 19 2002 -Prev. Note : This information is necessary when you download new software or you need to repair the receiver. 47 6 Setting Timer (Automatic power On/Off) You can pre-set the on/off time of your receiver. During your absence, you can record programs on your VCR. Press MENU key. Press or to select ‘System Parameters’, and press Screen System Parameters Parental Control System Information Local time/Timer DL Saving No TV Type 4X3 Screen P/S 0 ~ 9 -Edit, or MULTI Aspect Ratio Press 18/07/2001 16:43 RF Channel -Prev. to select ‘Local Time/Timer’, and press Note : Without the local time setting, this ‘TIMER’ function does not work. Screen Timer 18/07/2001 16:40 Timer #1 CH. Type Timer #2 CH. Number Timer #3 CH. Name Fujian 1 Timer #4 Start Time 18/07/2001 16:42 Timer #5 Stop Time 18/07/2001 17:42 TV Timer #6 Timer #7 -Edit, Press or Status -Main, No -Prev. to select ‘Timer #(number)’ you want to set and press determine 'CH. Type' by selecting 'TV' or 'RADIO' with 48 or Select 'CH. Number' with numeric keys or with or or and enter channel number with Select ‘Start Time’ for your receiver power-on. For example : For 1st of February in the year of 2000, 7:30 P.M., Enter in sequence Select ‘Stop Time’ by pressing Enter power off time in the same way as you entered ‘Start Time’ Select ‘Status’ and set ‘Yes/No’ with or Note : 1. Without ‘STATUS’ being actuated (ON), Timer does not work. 2. If Prior time than current is entered, Timer does not work. 3. You can pre-set 7 TIMERs simultaneously. Regardless of number of TIMER, Timer will work in sequence of time sequence. 4. Remocon Key doesn’t work while Timer is ‘On’ for stable VCR recording. Setting Day Light Saving Time (Summer Time) You can adjust current local time when summer time is applicable. Press MENU key. Press or to select ‘System Parameters’, and press Press or to select ‘DL Saving’. Press or to select ‘Yes’ or ‘No’ . Yes No Set for daylight saving function activated The current time automatically moves one hour ahead Set for daylight saving function deactivated The current time automatically moves on hour behind Note : Without current local time setting, this menu cannot be processed. 49 8 Setting TV Type You can set your TV display mode with this sub-menu. Press MENU key. Press or to select ‘System Parameters’, and press Press or to select ‘TV Type’. Press Multi PAL NTSC or to select ‘Multi’, ‘PAL’, or ‘NTSC’. When your TV is compatible with NTSC/PAL dual mode. When your TV is only for PAL reception. Regardless of satellite signal, the display will be done in PAL format. When your TV is only for NTSC reception. Regardless of satellite signal, the display will be done in NTSC format. Note : If the satellite signal and your TV type are mismatched, the TV picture may be distorted. Even in this case, MENU will be displayed as normal. (e.g. When you receive PAL satellite signal with NTSC TV type setting or vice versa) 50 9 Setting Aspect Ratio This sub-menu allows you to select your TV aspect ratio to 4:3 or 16:9 according to your wishes. Press MENU key. Press or to select ‘System Parameters’, and press Press or to select ‘Aspect Ratio’. Press or to select ‘4x3’ or ‘16x9’. 4x3 16x9 When your TV is 4:3. When your TV is 16:9. Note : If you set 4 x 3 when the Satellite input signal is 16 x 9, the right and the left parts of the original picture may not be seen. 51 10 Setting Screen You can select the satellite input signal display mode. Press MENU key. Press or to select ‘System Parameters’, and press Press or to select ‘Screen’. Press or to select ‘P/S’ or ‘L. Box’. When you set screen display boundary from Pan/Scan data of Satellite input signal. (For signal for 16x9 program) P/S You can watch 16 x 9 ratio screen by reducing original size vertically and horizontally. L.Box Note : 1. If you select ‘L.Box’, the screen might be distorted. Upper and lower part of the screen will be blocked with black stripes. 2. ‘Screen’ function is helpful when receiving 16 x 9 signal with TV of 4x3 format. 11 Setting Output Channel no. of RF Modulator You can select the channel number for the RF modulator output. Press MENU key. Press or to select ‘System Parameters’, and press Press or to select ‘RF Channel’. Press or to select channel number you want. Note : RF modulator channel number has nothing to do with any channel numbers of TV ANT IN signal. 52 1 TP Edit / Scan After ‘LNB Configuration’ and ‘Antenna Setup’ procedure, when necessary, you can edit and/or add certain TPs (transponders) Press MENU key. or Select ‘Installation’ with , and press Screen Installation LNB Configuration Antenna Setup Satellite Scan TP Edit/Scan Factory Set -Next, -Prev. Select ‘TP Edit/Scan’ with or , and press Screen TP Edit/Scan Good Satellite Name AsiaSat 2 TP Frequency [24] 4,000 GHz Polarization Horizontal-18V Symbol Rate 28,123 MSPS Scan Free+Scrambled TP Delete 81% -Select, -Main, -Prev. Select the ‘Satellite Name’ which includes the TP you want to add/edit with or Move to ‘TP Frequency’with edit with or and select the TP you want to If you want to add the new TP, enter the TP frequency with numeric keys. 53 Select ‘Polarization’ by pressing value for selected TP with or and the set the proper Select ‘Symbol rate’ by pressing and enter the symbol rate value for the selected TP with numeric keys . After entering all values of the TP parameters, move to ‘SCAN’ section (column) with and press for storing all the entered TP data. As a result, you can get the following menu showing the scanning process. Screen TP Edit/Scan Satellite Name USER Scanning [15] 3,820 GHz to stop scanning Vertical-14V TP Frequency Press Polarization Good Symbol Rate 28,123 MSPS Scan Free+Scrambled TP Delete 81% -Select, -Main, -Prev. After scanning process, the first channel of scanned TP will be displayed. Screen TP Edit/Scan TV: 10 11 12 13 14 15 16 Good 82% Success 17 18 19 20 21 22 RAI Internati TVE TV5-Asia RTPi uØoH-u1/4Ö¥x CS ªFËê>>Ú¥x ET «DoZ¥x USTV-I oé¥>>¥x JET AsiaSat 2 -Page Up/Down, [24] 4,000 GHz -Watch, Radio: 20 DW 9 RDP ANTENA 1 RDP ESPECIAL NN ¥xÆWaN¥<< TWN ¥@uØ1/2Auø USA- Hor. 28,123 -Prev. Note : If the scan fails, please check whether your entered values are correct or not and the signal reception sensitivity is good or bad. 54 2 TP Delete Press MENU key. Select ‘Installation’ with or Select ‘TP Edit/Scan’ with or , and press , and press Screen TP Edit/Scan Good Satellite Name AsiaSat 2 TP Frequency [24] 4,000 GHz Polarization Horizontal - 18V Symbol Rate 28,123 MSPS Scan Free+Scrambled TP Delete 80% -Select, -Main, -Prev. Move to TP section (column) with to delete with or and select the TP you want Move to ‘TP Delete’ section (column) by pressing and press When the menu asks you to confirm the deletion, press if you want to delete it or press EXIT key if you want to void the deletion. Screen TP Edit/Scan Satellite Name USER Do you want to delete this TP? [15] 3,820 GHz Yes / No Polarization Vertical-14V TP Frequency Good Symbol Rate 28,123 MSPS Scan Free+Scrambled TP Delete 81% -Select, -Main, -Prev. 55 The status of the receiver will return to factory default parameters by using this function. Press MENU key. Select ‘Installation’ with or , and press , and press Screen Installation LNB Configuration Antenna Setup Satellite Scan TP Edit/Scan Factory Set -Next, Select ‘Factory Set’ with -Prev. or Screen Installation LNB Configuration Do you want to reset all data? Antenna Setup Yes / No Satellite Scan TP Edit/Scan Factory Set -Next, -Prev. When the menu asks you to confirm the reset, press or press EXIT key if you want to void the reset. 56 if you want to reset 1 TV / SAT switching This function is used for receiving a signal through the RF modulator. If your receiver has no 'TV ANT IN' terminal in the rear panel, this key may not work. Press ‘TV/SAT’. The signal reception path will change to RF modulator and ‘TV/SAT’ LED on front panel will be lit. The signal output through the RF modulator will be as follows : TV/SAT LED ON OFF Power ON TV ANT IN signal will be out. Decoded signal will be out through RF. Power OFF TV ANT IN signal will be out. TV / RADIO switching You can use this menu when you change a TV channel to a Radio channel or vice versa. Press ‘TV/RADIO’. When listening a radio channel, ‘r001’ will be displayed on the front panel. 57 3 GUIDE(EPG:Electronic Program Guide) You can check the channel information on the channels of the transponder you are watching. Press GUIDE key, then the following menu will be displayed. Screen Program Guide 19:33 Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Current/Next, Current JOURNAL News - Sports Weather - Interview JOURNAL Ne.. 19:23 -Schedule, 19:53 -Extended Note : 1. You can check local time, channel name, and other brief information on the current program. 2. If you didn't set local time under ‘System Parameters’ section, the GUIDE function may not work properly. 3. EPG information is delivered by satellite from service providers. If the channel does not carry any signal on the guide data, this function may not work properly. Select Channel with Then you can see current or next program information of the selected channel. If you press GREEN, current or next program information would be converted to next or current program information respectively. Screen Program Guide Program Guide 19:33 Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Current/Next, 19:34 Current JOURNAL News - Sports Weather - Interview JOURNAL Ne.. -Schedule, 19:23 -Extended 19:53 Fujian 1 DIGITL VID ANHUI TV NMCHTV Guangdong 1 Hunan 1 DWtv MCM -Current/Next, 58 Next In Focus In Focus -Schedule, 19:53 -Extended 20:23 If you press YELLOW, you can see program schedule list of the selected channel. Screen Program Guide 19:39 19:27~19:57 JOURNAL News - Sports.. 19:57~20:27 In Focus [7] DWtv 11/03/1998 19:27~19:57 20:27~20:57 20:57~21:27 21:27~21:57 21:57~22:27 JOURNAL News-SportsWeather - Interview JOURNAL Nachrichten - .. Thema JOURNAL News - Busines.. Germany Live 22:27~22:57 JOURNAL Nachrichten - .. 22:57~23:27 Im Focus -Current/Next, -Schedule, -Extended, -Reserve If you want to see program information of a program in the program schedule list, select the program with Then you can see the program information in the right window. Screen Program Guide 19:42 19:27~19:57 19:57~20:27 20:27~20:57 20:57~21:27 21:27~21:57 21:57~22:27 22:27~22:57 22:57~23:27 JOURNAL News - Sports.. In Focus JOURNAL Nachrichten - .. Thema JOURNAL News - Busines.. Germany Live JOURNAL Nachrichten - .. Im Focus -Current/Next, -Schedule, [7] DWtv 11/03/1998 20:27~20:57 JOURNAL Nachrichten Wirtsohaft - Wetter Tagesthema -Extended, -Reserve If you press BLUE, you can see extended program information of the selected program. Screen Program Guide 19:39 Guest: Marianne Birthler Commissioner for Stasi Files -Current/Next, -Schedule, -Extended 59 [7] DWtv 11/03/1998 19:27~19:57 JOURNAL News-SportsWeather - Interview You can set up automatic power on-off (Timer) on the program schedule list. After press YELLOW in the Guide( EPG) menu, select a program with or and press Select between 'No', 'Once', 'Daily' or 'Weekly' of 'Status' with or Screen Program Guide Program Guide 19:42 19:27~19:57 JOURNAL News - Sports.. Timer 19:57~20:27 In Focus 19:42 [7] DWtv 11/03/1998 20:27~20:57 JOURNA chrichten 20:27~20:57 JOURNAL Nachrichten - .. Weather -- Wetter 20:57~21:27 Thema 20:26 11/03/1998 11/03/1998 21:02 21:27~21:57 JOURNAL News - Busines.. Status No 21:57~22:27 Germany Live 22:27~22:57 JOURNAL Nachrichten - .. 22:57~23:27 Im Focus [7] DWtv 11/03/1998 20:27~20:57 JOURNA chrichten 20:27~20:57 JOURNAL Nachrichten - .. Weather -- Wetter 20:57~21:27 Thema 11/03/1998 20:26 11/03/1998 21:02 21:27~21:57 JOURNAL News - Busines.. Status Once 21:57~22:27 Germany Live 22:27~22:57 JOURNAL Nachrichten - .. 22:57~23:27 Im Focus -Reserve, -Reserve, Press 19:27~19:57 JOURNAL News - Sports.. Timer 19:57~20:27 In Focus to save the new 'Timer' setting. Screen Program Guide 19:42 19:27~19:57 19:57~20:27 20:27~20:57 20:57~21:27 21:27~21:57 21:57~22:27 22:27~22:57 22:57~23:27 JOURNAL News - Sports.. [7] DWtv In Focus Reserved at Timer #1 20:27~20:57 11/03/1998 JOURNAL Nachrichten - .. Wirtsohaft - Wetter Thema Tagesthema JOURNAL News - Busines.. Germany Live JOURNAL Nachrichten - .. Im Focus -Reserve, Press MENU, EXIT or to finish GUIDE menu. Note : 1. Without 'STATUS' being actuated (Yes), 'Timer' does not work. 2. If a program of prior time than current time ('Local Time' in 'System Parameters' menu) is selected, Timer does not work. 3. Refer to 'Setting Timer' in 'System Parameters' in this manual. 60 4 Subtitle/Audio You can adjust the subtitle and audio condition/status of the current channel. Press ‘AUDIO’ and subtitle and audio related window will be displayed on the screen. Screen Subtitle/Audio Subtitle Track 2 of 10 [Swedish] Audio Track 1 of 8 [English] Audio Mode Stereo Dig.Output Non-compressed -Subtitle On/Off In this example, program spoken language is 'English' and user's selected subtitle language is 'Swedish'. Screen The contents of each parameter are as follows ; Subtitle Track Audio Track (Subtitle language #) of (all subtitle language available in this program)[ Current selected subtitle language ] (Audio track #) of (all tracks available in this program ) [spoken language in this program ] Audio Mode Dig.Output Stereo -> Mono-Left -> Mono-Right Non-compressed / Compressed Note : These subtitle and audio parameters are workable only when the receiving channel supports these functions. 61 5 Teletext Teletext Service is text data service from Service Provider. It is available only when the satellite signal carries teletext service data. Press BLUE key and wait. If ‘*’ sign is pop up in the left upside of the screen as the following picture, wait until teletext service menu is displayed because ‘*’ means 'This program provides teletext service. So wait a moment'. Screen Teletext Service Data is displayed as following picture. Screen Select your interesting item with numeric keys. For example, if you want to see about 'CITY GUIDE', press Screen 62 6 Sleep Timer Your receiver will automatically power-off when the time you set is passed. Press ‘SLEEP’ key until the right time you want appears. Screen Note : 1. You can set SLEEP TIMER in 30 minute steps up to 150 minutes. 2. The SLEEP TIMER does not work while you are in ‘MENU’, ‘GUIDE’ or ‘CHANNEL LIST’. 63 7 Channel / Information Brief information is displayed, such as current channel type, name, local start/end time, guide information, current time, fav/normal mode, Audio mode and Audio ID. Press INFO, then the information bar will pop-up. Screen AsiaSat 2 5 DWtv ((( 1/8 (( 13:41 JOURNAL News-Busin... 13:26 ~ 13:56 Note : If you have no information : - Check your local time setting is correct. - Information is not sent by the channel provider. 64 There may be various reasons for the abnormal operation of the unit. Therefore, if the unit does not work properly, check it according to the procedures shown in the table below : Problem Possible causes Remedy LED on front panel AC power cord disconnected. Connect power cord properly into the power socket. does not light. No Picture or sound. Wrong connection of the Connect two terminals correctly video/audio output to TV input with RCA or RF cable. terminal. Wrong connection of satellite antenna cable. Connect the antenna cable correctly. Wrong direction of satellite antenna. Adjust the direction of antenna. No signal or weak signal. Check the cable connections, LNB and other equipment connected between the LNB and the receiver or adjust the antenna. Wrong setting of channel infor- Type the setting value correctly. mation in MENU screen. B l a c k - a n d - w h i t e Your TV mode is different from satellite broadcasting mode. screen or V-Hold. Use TV of same mode. Use the NTSC/PAL converter connected to the receiver and TV. The remote controller is not working. Change the batteries. Battery exhausted. Switch off the light. Fluorescent light interfering with the remote controller Remote controller is incorrectly Aim the remote control at the aimed. receiver. 65 System capabilities Fully DVB compliant LNB/Tuner input Connector IEC 169-24, female Frequency range 950MHz 2150MHz Signal level -65dBm 25dBm LNB supply 14/18V, max 400mA LNB switch control 22KHz DiSEqC Ver 1.2 Compatible Front end QPSK Symbol rate 2Msps Demodulator 45Msps SCPC and MCPC Capable System resource Video Decoder Spectral inversion Auto conversion Processor 32bit processor (80MHz) SDRAM 8Mbyte FLASH 2Mbyte EEPROM 2Kbyte MPEG 2 Main Proflie @ Main Level Data Rate up to 15M bits/s Resolution 720 X 576, 720 X 480 Video format NTSC, PAL Aspec Ratio 4:3, 16:9 Teletext DVB compliant MPEG Audio MPEG 1 layer 1 & 2 Serial data interface Type Mono, Dual mono, Stereo, Joint Stereo Sampling rates 32, 44.1 and 48 KHz Connector 9pin D-sub male, Max 115K bps 66 Remote control Power supply Rear Panel connectors RF modulator (PAL or NTSC) PAL G/I/K TV Type Physical Specification Code NEC-IR Operating condition up to 7 Meter Power consumption max 30W Supply voltage AC 120V Supply frequency 60 Hz Video out 1 X RCA cinch Audio L/R 2 X RCA cinch DIGITAL OUT 1 X RCA cinch Serial data 9pin D-sub Digital tuner input IEC 169 24 Loop-through Digital tuner IEC 169 24 Terrestrial ant input IEC 169 RF modulator output IEC 169 Connector IEC 169-2, female/male Frequency 470 Output channel number Size (W X H X 335 X 58.5 X 268(mm) Weight (Net) 3.2Kg 67 860MHz LIMITED WARRANTY PANAREX Inc. warrants to the original purchaser that this product shall be free from defects in workmanship and material for one year from the date of original purchase. During this warranty period PANAREX will provide free of charge both parts and labor necessary to correct defects in workmanship or material. This warranty dose not cover damage due to lightning, fire, flood, or other acts of God, damage from accident abnormal conditions, imporper use, or faulty installation, or damage by attempts to repair the units other than by the authorized service of PANAREX. PANAREX’s liablity under this warranty is limited to servicing or adjusting equipment returned to PANAREX authorized service centers with freight prepaid. Electronics Satelite TV System 11672 Tuxford Street. Sun Vailey, CA91352. U.S.A. Telephone : #818-768-5161 Fax : #818-768-5191 RISK OF ELECTRIC SHOCK, DO NOT OPEN ATTENTION : RISQUE CHOC LELECTRIQUE-NE PAS OUVRIR CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. AVIS POUR EVITER LE RISQUE D’INCENDIE OU CHOC ELECTRIQUE-NE PAS EXPOSER L’APPAREIL A LA PLUIE OU LA MOITEUR CAUTION : TO PREVENT ELECTRIC SHOCK. MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FUSE INSERT. ATTENTION : POUR ÉVITER LES CHOC ÉLECTRIQUES. INTRODURE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE ED LA PRISE ET POUSSER JUSOU’AU FOND. NOTE TO CATV SYSTEM INSTALLER : THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S ATTENTION TO ARTICLE 820-40 OF THE NEC THE PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDINGS AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. IMPORTANT SAFETY INSTRUCTIONS All the safety and operating instructions should be read before the product is operated. The safety and operating instructions should be retained for future reference. All warnings on the product and in the operating instructions should be adhered to. All operating and using instructions should be followed. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners, Use damp cloth for cleaning. Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink or laundry tub; in a wet basement; or near swimming pool; and the like. Do not place this product on an unstable cart, stand, tripod, bracket, or table, The product may fall, causing serious injury to a child or an adult and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. Do not use attachments not recommended by the product manufacturer as they may cause hazards. A product and cart combination should be moved with care. Quick stops, excessive forces and uneven surfaces may cause the product and cart combination to overturn. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. The openings should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For porducts intended to operate from battery power, or other sources, refer to the operating instructions. This product may be equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Power supply cord should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. If an outside antenna or clable system is connected to the product, be sure the antenna or cable system is grounded so as to porvide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mest and supporting structure, gorunding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. For added protedtion for this product during a lighting storm, or when it is left unattecded and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be tacken to keep from touching such power lines or circuits as contact with them might be fatal. Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. Never push any kinds of objects into this product through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill any kind of liquid on the product. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power supply cord or plug is damaged. If liquid has been spilled, or objects have fallen into the product. If the product has been exposed to rain to water. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qulaified technician to restore the product to its normal operation. If the product has been dropped or damaged in any way. When the product exhibits a distinct change in performance - this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement part specified by the manufacturer or have the same characteristics as the original part. Unauthorized subsitutions may result in fire, electric shock, or other hazards. Upon completion of any service or repair to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products(including amplifiers) that produce heat. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruclions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet of a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for assistance.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2002:02:27 12:13:55Z Modify Date : 2002:03:04 11:43:42-08:00 Page Count : 72 Creation Date : 2002:02:27 12:13:55Z Author : 김 호 진 Producer : Acrobat PDFWriter 4.0 Windows¿ë Mod Date : 2002:03:04 11:43:42-08:00 Metadata Date : 2002:03:04 11:43:42-08:00 Title : Manual_330A_.PDF Creator : 김 호 진EXIF Metadata provided by EXIF.tools