JVC KENWOOD J7V003 WIRELESS STEREO HEADSET User Manual HA W700BT J indd
JVC KENWOOD Corporation WIRELESS STEREO HEADSET HA W700BT J indd
Users Manual
![](/img.php?id=844898&img=bg1.png)
BLUETOOTH STEREO HEADSET
BLUETOOTH STEREO HEADSET
BLUETOOTH STEREO HEADSET
HA-W700BT -J/C
INSTRUCTIONS
MANUEL D’INSTRUCTIONS
MANUAL DE INSTRUCCIONES
1. To reduce the risk of electrical shocks, fire, etc.:
● Do not remove screws, cover or cabinet.
● Do not expose this appliance to rain or moisture.
2. For your safety…
● Never use the unit when driving a car, motorcycle, or bicycle. This
could result in an accident.
● Pay special attention to traffic around you when using the
headphones outside. Failure to do so could result in an accident.
● Be careful not to turn up the sound volume too high. Your hearing
can be damaged from listening to sounds at excessive volume for
long periods.
● Do not disassemble or modify the unit.
● Do not allow flammable, water or metallic objects to enter the unit.
● If you find skin problems where the headphones are in contact
with the skin, stop using the headphones; otherwise, it may cause
inflammation or irritation to the skin.
● In dry air such as in winter, you may feel a static shock when using
the headphones.
3. Avoid using the headphones…
● in places subject to excessive humidity or dust
● in places subject to extremely high (over 40°C or 104°F) or low
(under 0°C or 32°F) temperatures
4. DO NOT leave the unit…
● exposed to direct sunlight
● near a heater
5. To protect the unit, DO NOT…
● allow them to get wet
● shake them or drop them against hard objects
Thank you for purchasing this JVC product. Before you begin operating this unit, please read the operating instructions carefully to be sure you get
the best possible performance. If you have any questions, consult your JVC dealer.
6. For using the headphones…
● Attach the ear pieces firmly when replacing them; otherwise, the ear
pieces may be left in your ears when taking the headphones off. If the
ear piece is left in your ear, be careful not to push it deep into the ear
canal.
Be careful not to apply the power that exceeds the headphones’ input
capacity. This may result in sound distortion and could damage the
oscillation board.
Grasp and pull the plug itself to disconnect the headphones. Do not pull
on the cord.
When the ear pieces get dirty, detach the ear pieces and wash them in
water-diluted detergent. After washing, dry the ear pieces and attach to
the headphones.
Replace the ear pieces when: they lose its elasticity; they are stained
badly; they are broken or deformed.
The ear pieces will deteriorate with age even in normal use and
maintenance.
Store the ear pieces in a place where children cannot reach to avoid the
risk of the accident such as swallowing them.
● When using canal type headphones, you may hear the sound of cord
rubbing together or the sound of vibrations which travels through your
body when walking.
7. For safe use of battery…
● Use only the supplied charging unit to charge the battery.
● Be sure to use the supplied AC adaptor.
● There are no serviceable parts inside. Consult your dealer to replace
the built-in battery.
● When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of these
batteries must be followed strictly.
English
Listening to Music
Preparation:
• Make sure that the Bluetooth device can transmit music through the
Bluetooth connection (compatible with the A2DP profile of Bluetooth)
• Finish pairing between the unit and the Bluetooth device.
• Turn on the Bluetooth device.
1 Turn on the unit.
2 Execute the Bluetooth (A2DP) connection on the
Bluetooth device.
• Refer also to the instruction manual supplied for the target device.
• If the connection is not completed within five minutes, this unit goes
to power saving mode. In this case, repeat the procedure from step 1.
3 Start playback on the Bluetooth device.
• Set the connected Bluetooth device so that the device emits the sound
through the Bluetooth stereo headphones.
4 Adjust the volume by tilting the control switch up or
down.
Basic controls available for the device:
Button Press Press and hold
6Play/pause Stop*
¢Skip (to the next) Search (to forward)*
4Skip (to the previous) Search (to backward)*
* Not available for some devices.
• You can perform some of the Bluetooth device operations with
the control switch of the unit if the device is compatible with the
AVRCP profile. The operations you can do may vary depending on
the device you use. Refer also to the instruction manual supplied for
the target device to see the available operations.
To stop using the unit
Disconnect the Bluetooth connection on the Bluetooth device and turn off
the unit.
For the better sound and comfort fit of the headphones
The medium-size ear pieces are attached to the supplied headphones
when purchased.
You may not enjoy the bass sound fully if the ear pieces are not fit
to your ears. To enjoy better sound while reducing sound leakage
and getting full noise canceling effect, choose the ear pieces from
the supplied three sizes (Small, Medium, or Large) and adjust their
positions to fit them to your ears.
Troubleshooting
What appears to be trouble is not always serious. Check the following
points before consult your JVC dealer.
Cannot pair the devices.
☞ You cannot pair the Bluetooth device having receiving function only.
☞ Bring the devices as closer as possible.
Cannot connect the devices.
☞ Pairing is incomplete. Perform the pairing again.
☞ Check that the Bluetooth communication function is activated in the
Bluetooth device.
The sound is intermittent/The communication range is small.
☞ Although Bluetooth wireless technology can transmit the contents
within the range of approx. 10 m, obstacles (human bodies, metallic
objects, wall, etc.) or radiowave condition may affect the sound and
decrease its range.
☞ The sound may be intermittent in the following cases. Avoid the
following conditions when you use this unit.
– Places where the wireless local area network is applied.
– Near the microwave oven.
– Near the other Bluetooth devices.
– Places where the radiowave is used.
No sound.
☞ The connection between the Bluetooth device and this unit is
incomplete. Connect the devices again.
☞ The setting of the Bluetooth device is incorrect. Set the connected
Bluetooth device so that the device emits the sound through the
Bluetooth stereo headphones.
Printed in China
LNT0091-001A
© 2007 Victor Company of Japan, Limited
Battery disposal
When disposing the unit, take off the built-in lithium-ion battery and
dispose appropriately for environmental protection.
1. Take off the screws with the
Phillips-head screwdriver.
2. Open the case and take off the
battery.
• Do not take off the battery from its case
when you dispose of the battery.
Calling through the unit
Preparation:
• Activate the Bluetooth communication function on your cellular phone.
• Finish pairing between the unit and your cellular phone.
1 Turn on the unit.
2 Execute the Bluetooth connection on the cellular phone.
• Refer also to the instruction manual supplied for the cellular phone.
• When using a cellular phone supports both HFP and HSP Bluetooth
Profile, use HFP for this unit.
• When the connection is completed, the blue lamp flashes repeatedly.
Basic controls available for the cellular phone connected with HFP:
Status CALL button
Press Press and hold
Waiting Start voice dialing Redial
Dialing by
voice dialing
Cancel voice dialing —
Calling Cancel calling —
Incoming Answer the call Reject the call
Answering Finish the call Switch the device
(between cellular phone
and audio device)
Basic controls available for the cellular phone connected with HSP:
Status CALL button
Press Press and hold
Waiting — Start calling*1
Calling Cancel calling*1Cancel calling or activate
the audio player*2
Incoming Answer the call —
Answering Finish the call*3Activate the audio
device
*1 Not available on some cellular phones.
*2 Varies depending on the model of the cellular phone.
*3 When answering a call on cellular phone, the function may not work.
To make a call while playing back music
When connecting the cellular phone by using HFP or HSP Bluetooth
Profile, you can make a call by using the cellular phone.
To answer a call while playing back music
When a call comes in, the playback sound turns to ring tone. Press the
CALL button to answer the call.
To finish the call
Press the CALL button. The playback sound comes back. (The playback
sound may not come back in some cellular phone.)
You can register up to 8 Bluetooth devices to the unit.
• The device that has the oldest connection date will be overwritten when
you register a 9th Bluetooth device.
Before pairing...
• Make sure that the unit is turned off.
• Turn on the target Bluetooth device and place it within 1 m from the
unit.
1 Turn on the unit with pressing and holding the CALL
button to make it in the pairing mode.
The blue lamp and the red lamp will start flashing continuously as the
unit finds the target Bluetooth device (pairing mode). Release the CALL
button after the flashing starts.
• Finish the steps below within about 3 minutes after the flashing
starts (the pairing mode is automatically cancelled after the period).
Turn off the unit and start from step 1 again when you cannot finish
the operation.
2 Execute pairing operation on the target Bluetooth device
to find the unit.
The device shows the list of Bluetooth devices found. The unit is
recognized as “JVC HA-W700BT”. Repeat from Step 1 again when
“JVC HA-W700BT” is not found.
• Refer also to the instruction manual supplied for the target device.
Registering a Bluetooth device – Pairing
3 Select “JVC HA-W700BT” on the target Bluetooth
device.
4 Enter “0000” when the Pass code* is requested on the
target Bluetooth device.
Pairing is finished when the red lamp goes out and the blue lamp
flashes three times repeatedly.
* also called as “pass key”, “PIN code”, “PIN number”, etc.
5 Execute Bluetooth connection to the unit on the target
Bluetooth device.
The unit saves the target as the last connected Bluetooth device.
• Refer also to the instruction manual supplied for the target device.
• Some Bluetooth device will automatically connect with the unit after
pairing is finished.
• When the connection is completed, the blue lamp flashes repeatedly.
To pair with devices which cannot show the Bluetooth device list...
On some Bluetooth devices, pairing may automatically be established by
making both the unit and the target device in the pairing mode. Refer also
to the instruction manual supplied for the target device to make it in the
pairing mode.
CAUTION
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not approved by JVC
could void user’s authority to operate the equipment.
Contact
Address: JVC AMERICAS CORP.
JVC COMPANY OF AMERICA
1700 Valley Road, Wayne, N.J. 07470
Telephone: 1 (800) 252-5722
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, it may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
IC INFORMATION
This device complies with RSS-210 of the IC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
interference that may cause undesired operation of the
device.
CAUTION: Changes or modifications not approved by JVC
could void user’s authority to operate the equipment.
Contact
Address: JVC CANADA INC.
21 Finchdene Square, Toronto, ON M1X 1A7
Telephone: (416) 293-1311
e-mail: info@jvc.ca
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Industry Canada’s RSS-210. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, it may cause
harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
INFORMATION SUR IC
Cet appareil est conforme à la RSS-210 du réglement de la IC.
Le fonctionnement est sujet aux deux conditions suivantes:
(1) Cet appareil ne peut causer d’interférences nuisi-bles
(2) Cet appareil reçoit toute interférence même les interférences
qui peuvent occasioner un mauvais fonctionnement.
ATTENTION: Les changements ou les modifications non
approuvés par JVC risquent de retirer à l’utilisateur le droit
d’utiliser l’appareil.
Contact
Adresse: JVC CANADA INC.
21 Finchdene Square, Toronto, ON M1X 1A7
Téléphone: (416) 293-1311
e-mail: info@jvc.ca
Remarque: L’appareil a été testé et jugé conforme aux limites
des appareils numériques de classe B, aux termes de la
réglementation RSS-210 de l’industrie du Canada. Ces limites
ont pour but d’assurer une protection raisonnable contre les
interférences parasites lorsque l’appareil est utilisé dans
une installation résidentielle. Cet appareil engendre, utilise
et peut émettre une énergie radioélectrique et, s’il n’est pas
installé et utilisé en stricte conformité avec ces instructions, il
peut provoquer des interférences parasites dans les liaisons
radiophoniques. Ceci ne garantit pas pour autant qu’une
installation particulière n’émettra aucune interférence. Si
l’appareil engendre des interférences parasites avec la réception
radio ou télévision, ce qui pourra être déterminé en éteignant
puis en rallumant l’appareil, il est conseillé à l’utilisateur
d’essayer de corriger les interférences en prenant l’une des
mesures ci-dessous:
• Modifier l’orientation ou changer l’emplacement de l’antenne
de réception.
• Eloigner davantage l’appareil du récepteur.
• Brancher l’appareil dans une prise d’un circuit différent de
celui auquel le récepteur est raccordé.
• Demander l’aide de son agent ou d’un technicien radio/
télévision qualifié.
IMPORTANT
CAUTION:
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS PLUG
WITH AN EXTENSION CORD, RECEPTACLE OR OTHER
OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
ATTENTION:
POUR PREVENIR LES CHOCS ELECTRIQES NE PAS
UTILISER CETTER FICHE AVEC UN PROLONGATEUR, UNE
PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT,
SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND
SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the device.
(1) Ce produit ne cause pas d’interférence.
(2) Ce produit doit accepte toute interférence, incluant
interférence qui peut causé opération non désiré.
ENGLISH
This product’s performance would be degraded under a strong
electro-static environment. And the function would be self-
recoverable after the above case.
This product’s performance would be degraded since the
disturbance from the mains cord. And the function would be self-
recoverable after the above case.
FRANÇAIS
Les performances de ce produit se détérioreront dans un
environnement fortement électro-statique. Par ailleurs, le
fonctionnement se restaurera de lui-même dans le cas ci-dessus.
Les performances de ce produit se détérioreront en cas
de perturbations du cordon d’alimentation. Par ailleurs, le
fonctionnement se restaurera de lui-même dans le cas ci-dessus.
ESPAÑOL
El rendimiento de este producto puede deteriorarse en un entorno
con campos electrostáticos fuertes. El funcionamiento se repondrá
a la normalidad después del caso arriba mencionado.
El rendimiento de este producto puede deteriorarse debido a las
perturbaciones del cable de la red eléctrica. El funcionamiento se
repondrá a la normalidad después del caso arriba mencionado.
Hearing Comfort and Well-Being
• Do not play your personal audio at a high volume. Hearing
experts advice against continuous extended play.
• If you experience a ringing in your ears, reduce volume or
discontinue use.
Traffic safety
• Do not use while operating a motorized vehicle. It may create a
traffic hazard and is illegal in many area.
• You should use extreme caution or temporarily discontinue use
in potentially hazardous situations.
• Even though your earphones are of the open-air type designed
to let you hear outside sounds, don’t turn up the volume so
high that you can’t hear what’s around you.
Specifications
General
Bluetooth version: Bluetooth 2.0 certified
Output power: Bluetooth power class 2
Service area: max. 10 m (10.9 yd.) (approx.)*
* Communication range may vary depending on the environmental
conditions.
Frequency band: 2.4 GHz (2,4000 GHz – 2,4835 GHz)
Bluetooth profile:
A2DP (Advanced Audio Distribution Profile), AVRCP (Audio/Video
Remote Control Profile), HFP (Hands-free Profile), HSP (Headset
Profile)
Supported Codec: SBC
Power supply: Built-in lithium-ion rechargeable battery (DC 3.7 V)
Battery life*: Music play time: max. XXX hours
Standby time: max. XXX hours
* Depends on use.
Mass: 35 g (1.23 oz.) (including headphones)
Headphones (J48139-001)
Frequency response: 10 Hz – 23,000 Hz
Sensitivity: 93 dB/1 mW
Accessories
AC adaptor x 1 (S004CU0500050), Ear pieces (3 pairs, L, M, S), Charging
unit (J48140-001) x 1
Designs and specifications are subject to change without notice.
The Bluetooth® word mark and logos are registered trademarks owned
by Bluetooth SIG, Inc. and any use of such marks by Victor Company of
Japan, Limited (JVC) is under license. Other trademarks and trade names
are those of their respective owners.
Parts name
1
8
234 5
67
9p
q
1 (CALL) button
Controls the cellular phone calling through this unit.
2 Control switch*
Controls the music player connected with this unit.
3 Red lamp
Indicates the battery status of this unit.
4 Blue lamp
Indicates the communication status between this
unit and Bluetooth equipment.
5 Microphone
Picks up your voice when calling through this unit.
6 Strap hole
7 Stereo mini jack
8 Headphones
9 Battery charge terminal
p Clip
q POWER switch
Slides to turn on or off this unit.
* The volume level of the connected device cannot be
changed from this unit.
Battery
Features
This unit is a wireless stereo headset using Bluetooth® wireless technology.
Call Call
Control Control
iPod with Bluetooth
Transmitter
Bluetooth cell phone
As Bluetooth Stereo Headset As Bluetooth Receiver
Control
Music & Call
Bluetooth cell phone
with music player Bluetooth audio source
Music
• Checking the battery charge
Press the PLAY/PAUSE button while holding the CALL button. (Press the
PLAY/PAUSE button within two seconds after pressing CALL button.)
The red lamp lights or flashes to show the battery remains.
• The red lamp starts slow flashing automatically when the battery
become nearly empty.
Battery charging
Charge the built-in rechargeable lithium-ion battery first to use this unit.
1 Connect the AC adaptor to the charging unit.
• Do not use any AC adaptor other than the supplied one.
2 Connect the AC adaptor to the AC outlet.
3 Put the unit on the charging stand.
The red lamp lights up when the battery charge terminals contact.
The blue lamp will light up when the charging is finished (the red lamp will
turn off).
• It takes about three hours to charge the battery to full when it is empty.
• You can use the unit while charging.
• Disconnect the AC adaptor from the AC outlet when you do not use the
charging unit for a extended period of time.
• Do not pull the cord when disconnecting the AC adaptor.
• Do not handle the power cord with wet hands!
• Do not bend the power cord sharply.
Battery charge
terminal
Red lamp Battery level
Remain lit Full
Flash continuously Halfway
Two short flashes twice Low
One short flash twice Need to charge
About Bluetooth
Bluetooth is a short-range wireless radio communication technology for
the mobile device such as cellular phones, portable PCs, and other devices.
The Bluetooth devices can be connected without cables and communicate
each other.
About Bluetooth Profile
Bluetooth Profile designates the way of communication between Bluetooth
devices. The system supports the following Bluetooth Profiles.
A2DP: Advanced Audio Distribution Profile
The profile controls sending/receiving the high-quality audio contents.
AVRCP: Audio/Video Remote Control Profile
The profile controls the functions of audio/video devices such as playing,
stopping, pausing and volume control.
HSP: Headset Profile
The profile controlling the cell phone, and controlling the connection
between the devices.
HFP: Hands-Free Profile
The profile controls the hands-free call with cell phone.
About pairing
Pairing creates a unique and encrypted link between two Bluetooth devices
and lets them communicate with each other. Bluetooth devices will not
work if the devices have not been paired.
Cautions on Bluetooth communication
• Microwaves emitted from Bluetooth devices may affect the operation
of electronic medical devices. Turn off this unit and other Bluetooth
devices in hospitals, airplanes, trains, or crowding places.
• Bluetooth devices use 2.4 GHz band, which is the same as that used by
wireless LAN devices and microwave oven. Interference may occur
near these devices and cause noise, disconnectivity, or a decrease of
communication speed.
• Connection with all Bluetooth devices cannot be guaranteed.
Connectivity, operation, display indication or function may differ
depending on the characteristics and specification of the devices.
• Some Bluetooth devices take more time to establish connection.
• To use the Bluetooth functions, the Bluetooth devices are required to be
compatible with the same Bluetooth profiles as this unit is. However, the
functions may differ depending on the specifications of the Bluetooth
device even when it is compatible with the same profiles.
LED flashing patterns
Status LED Flashing pattern
While pairing Blue ●-●-●-●-●-●-●-●-●-●-●-●-●-
Red ●-●-●-●-●-●-●-●-●-●-●-●-●-
Connecting Blue ●-●-●--------------●-●-●----------
Red ------------------------------------------
Communicating Blue ●---------------------●-----------------
Red ------------------------------------------
HA-W700BT_J.indd 1HA-W700BT_J.indd 1 07.8.1 2:38:54 PM07.8.1 2:38:54 PM
![](/img.php?id=844898&img=bg2.png)
1. To reduce the risk of electrical shocks, fire, etc.:
● Do not remove screws, cover or cabinet.
● Do not expose this appliance to rain or moisture.
2. For your safety…
● Never use the unit when driving a car, motorcycle, or bicycle. This
could result in an accident.
● Pay special attention to traffic around you when using the
headphones outside. Failure to do so could result in an accident.
● Be careful not to turn up the sound volume too high. Your hearing
can be damaged from listening to sounds at excessive volume for
long periods.
● Do not disassemble or modify the unit.
● Do not allow flammable, water or metallic objects to enter the unit.
● If you find skin problems where the headphones are in contact
with the skin, stop using the headphones; otherwise, it may cause
inflammation or irritation to the skin.
● In dry air such as in winter, you may feel a static shock when using
the headphones.
3. Avoid using the headphones…
● in places subject to excessive humidity or dust
● in places subject to extremely high (over 40°C or 104°F) or low
(under 0°C or 32°F) temperatures
4. DO NOT leave the unit…
● exposed to direct sunlight
● near a heater
5. To protect the unit, DO NOT…
● allow them to get wet
● shake them or drop them against hard objects
Thank you for purchasing this JVC product. Before you begin operating this unit, please read the operating instructions carefully to be sure you get
the best possible performance. If you have any questions, consult your JVC dealer.
6. For using the headphones…
● Attach the ear pieces firmly when replacing them; otherwise, the ear
pieces may be left in your ears when taking the headphones off. If the
ear piece is left in your ear, be careful not to push it deep into the ear
canal.
Be careful not to apply the power that exceeds the headphones’ input
capacity. This may result in sound distortion and could damage the
oscillation board.
Grasp and pull the plug itself to disconnect the headphones. Do not pull
on the cord.
When the ear pieces get dirty, detach the ear pieces and wash them in
water-diluted detergent. After washing, dry the ear pieces and attach to
the headphones.
Replace the ear pieces when: they lose its elasticity; they are stained
badly; they are broken or deformed.
The ear pieces will deteriorate with age even in normal use and
maintenance.
Store the ear pieces in a place where children cannot reach to avoid the
risk of the accident such as swallowing them.
● When using canal type headphones, you may hear the sound of cord
rubbing together or the sound of vibrations which travels through your
body when walking.
7. For safe use of battery…
● Use only the supplied charging unit to charge the battery.
● Be sure to use the supplied AC adaptor.
● There are no serviceable parts inside. Consult your dealer to replace
the built-in battery.
● When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of these
batteries must be followed strictly.
French
Listening to Music
Preparation:
• Make sure that the Bluetooth device can transmit music through the
Bluetooth connection (compatible with the A2DP profile of Bluetooth)
• Finish pairing between the unit and the Bluetooth device.
• Turn on the Bluetooth device.
1 Turn on the unit.
2 Execute the Bluetooth (A2DP) connection on the
Bluetooth device.
• Refer also to the instruction manual supplied for the target device.
• If the connection is not completed within five minutes, this unit goes
to power saving mode. In this case, repeat the procedure from step 1.
3 Start playback on the Bluetooth device.
• Set the connected Bluetooth device so that the device emits the sound
through the Bluetooth stereo headphones.
4 Adjust the volume by tilting the control switch up or
down.
Basic controls available for the device:
Button Press Press and hold
6Play/pause Stop*
¢Skip (to the next) Search (to forward)*
4Skip (to the previous) Search (to backward)*
* Not available for some devices.
• You can perform some of the Bluetooth device operations with
the control switch of the unit if the device is compatible with the
AVRCP profile. The operations you can do may vary depending on
the device you use. Refer also to the instruction manual supplied for
the target device to see the available operations.
To stop using the unit
Disconnect the Bluetooth connection on the Bluetooth device and turn off
the unit.
For the better sound and comfort fit of the headphones
The medium-size ear pieces are attached to the supplied headphones
when purchased.
You may not enjoy the bass sound fully if the ear pieces are not fit
to your ears. To enjoy better sound while reducing sound leakage
and getting full noise canceling effect, choose the ear pieces from
the supplied three sizes (Small, Medium, or Large) and adjust their
positions to fit them to your ears.
Troubleshooting
What appears to be trouble is not always serious. Check the following
points before consult your JVC dealer.
Cannot pair the devices.
☞ You cannot pair the Bluetooth device having receiving function only.
☞ Bring the devices as closer as possible.
Cannot connect the devices.
☞ Pairing is incomplete. Perform the pairing again.
☞ Check that the Bluetooth communication function is activated in the
Bluetooth device.
The sound is intermittent/The communication range is small.
☞ Although Bluetooth wireless technology can transmit the contents
within the range of approx. 10 m, obstacles (human bodies, metallic
objects, wall, etc.) or radiowave condition may affect the sound and
decrease its range.
☞ The sound may be intermittent in the following cases. Avoid the
following conditions when you use this unit.
– Places where the wireless local area network is applied.
– Near the microwave oven.
– Near the other Bluetooth devices.
– Places where the radiowave is used.
No sound.
☞ The connection between the Bluetooth device and this unit is
incomplete. Connect the devices again.
☞ The setting of the Bluetooth device is incorrect. Set the connected
Bluetooth device so that the device emits the sound through the
Bluetooth stereo headphones.
Battery disposal
When disposing the unit, take off the built-in lithium-ion battery and
dispose appropriately for environmental protection.
1. Take off the screws with the
Phillips-head screwdriver.
2. Open the case and take off the
battery.
• Do not take off the battery from its case
when you dispose of the battery.
Calling through the unit
Preparation:
• Activate the Bluetooth communication function on your cellular phone.
• Finish pairing between the unit and your cellular phone.
1 Turn on the unit.
2 Execute the Bluetooth connection on the cellular phone.
• Refer also to the instruction manual supplied for the cellular phone.
• When using a cellular phone supports both HFP and HSP Bluetooth
Profile, use HFP for this unit.
• When the connection is completed, the blue lamp flashes repeatedly.
Basic controls available for the cellular phone connected with HFP:
Status CALL button
Press Press and hold
Waiting Start voice dialing Redial
Dialing by
voice dialing
Cancel voice dialing —
Calling Cancel calling —
Incoming Answer the call Reject the call
Answering Finish the call Switch the device
(between cellular phone
and audio device)
Basic controls available for the cellular phone connected with HSP:
Status CALL button
Press Press and hold
Waiting — Start calling*1
Calling Cancel calling*1Cancel calling or activate
the audio player*2
Incoming Answer the call —
Answering Finish the call*3Activate the audio
device
*1 Not available on some cellular phones.
*2 Varies depending on the model of the cellular phone.
*3 When answering a call on cellular phone, the function may not work.
To make a call while playing back music
When connecting the cellular phone by using HFP or HSP Bluetooth
Profile, you can make a call by using the cellular phone.
To answer a call while playing back music
When a call comes in, the playback sound turns to ring tone. Press the
CALL button to answer the call.
To finish the call
Press the CALL button. The playback sound comes back. (The playback
sound may not come back in some cellular phone.)
You can register up to 8 Bluetooth devices to the unit.
• The device that has the oldest connection date will be overwritten when
you register a 9th Bluetooth device.
Before pairing...
• Make sure that the unit is turned off.
• Turn on the target Bluetooth device and place it within 1 m from the
unit.
1 Turn on the unit with pressing and holding the CALL
button to make it in the pairing mode.
The blue lamp and the red lamp will start flashing continuously as the
unit finds the target Bluetooth device (pairing mode). Release the CALL
button after the flashing starts.
• Finish the steps below within about 3 minutes after the flashing
starts (the pairing mode is automatically cancelled after the period).
Turn off the unit and start from step 1 again when you cannot finish
the operation.
2 Execute pairing operation on the target Bluetooth device
to find the unit.
The device shows the list of Bluetooth devices found. The unit is
recognized as “JVC HA-W700BT”. Repeat from Step 1 again when
“JVC HA-W700BT” is not found.
• Refer also to the instruction manual supplied for the target device.
Registering a Bluetooth device – Pairing
3 Select “JVC HA-W700BT” on the target Bluetooth
device.
4 Enter “0000” when the Pass code* is requested on the
target Bluetooth device.
Pairing is finished when the red lamp goes out and the blue lamp
flashes three times repeatedly.
* also called as “pass key”, “PIN code”, “PIN number”, etc.
5 Execute Bluetooth connection to the unit on the target
Bluetooth device.
The unit saves the target as the last connected Bluetooth device.
• Refer also to the instruction manual supplied for the target device.
• Some Bluetooth device will automatically connect with the unit after
pairing is finished.
• When the connection is completed, the blue lamp flashes repeatedly.
To pair with devices which cannot show the Bluetooth device list...
On some Bluetooth devices, pairing may automatically be established by
making both the unit and the target device in the pairing mode. Refer also
to the instruction manual supplied for the target device to make it in the
pairing mode.
CAUTION
Specifications
General
Bluetooth version: Bluetooth 2.0 certified
Output power: Bluetooth power class 2
Service area: max. 10 m (10.9 yd.) (approx.)*
* Communication range may vary depending on the environmental
conditions.
Frequency band: 2.4 GHz (2,4000 GHz – 2,4835 GHz)
Bluetooth profile:
A2DP (Advanced Audio Distribution Profile), AVRCP (Audio/Video
Remote Control Profile), HFP (Hands-free Profile), HSP (Headset
Profile)
Supported Codec: SBC
Power supply: Built-in lithium-ion rechargeable battery (DC 3.7 V)
Battery life*: Music play time: max. XXX hours
Standby time: max. XXX hours
* Depends on use.
Mass: 35 g (1.23 oz.) (including headphones)
Headphones (J48139-001)
Frequency response: 10 Hz – 23,000 Hz
Sensitivity: 93 dB/1 mW
Accessories
AC adaptor x 1 (S004CU0500050), Ear pieces (3 pairs, L, M, S), Charging
unit (J48140-001) x 1
Designs and specifications are subject to change without notice.
The Bluetooth® word mark and logos are registered trademarks owned
by Bluetooth SIG, Inc. and any use of such marks by Victor Company of
Japan, Limited (JVC) is under license. Other trademarks and trade names
are those of their respective owners.
Parts name
1
8
234 5
67
9p
q
1 (CALL) button
Controls the cellular phone calling through this unit.
2 Control switch*
Controls the music player connected with this unit.
3 Red lamp
Indicates the battery status of this unit.
4 Blue lamp
Indicates the communication status between this
unit and Bluetooth equipment.
5 Microphone
Picks up your voice when calling through this unit.
6 Strap hole
7 Stereo mini jack
8 Headphones
9 Battery charge terminal
p Clip
q POWER switch
Slides to turn on or off this unit.
* The volume level of the connected device cannot be
changed from this unit.
Battery
Features
This unit is a wireless stereo headset using Bluetooth® wireless technology.
Call Call
Control Control
iPod with Bluetooth
Transmitter
Bluetooth cell phone
As Bluetooth Stereo Headset As Bluetooth Receiver
Control
Music & Call
Bluetooth cell phone
with music player Bluetooth audio source
Music
• Checking the battery charge
Press the PLAY/PAUSE button while holding the CALL button. (Press the
PLAY/PAUSE button within two seconds after pressing CALL button.)
The red lamp lights or flashes to show the battery remains.
• The red lamp starts slow flashing automatically when the battery
become nearly empty.
Battery charging
Charge the built-in rechargeable lithium-ion battery first to use this unit.
1 Connect the AC adaptor to the charging unit.
• Do not use any AC adaptor other than the supplied one.
2 Connect the AC adaptor to the AC outlet.
3 Put the unit on the charging stand.
The red lamp lights up when the battery charge terminals contact.
The blue lamp will light up when the charging is finished (the red lamp will
turn off).
• It takes about three hours to charge the battery to full when it is empty.
• You can use the unit while charging.
• Disconnect the AC adaptor from the AC outlet when you do not use the
charging unit for a extended period of time.
• Do not pull the cord when disconnecting the AC adaptor.
• Do not handle the power cord with wet hands!
• Do not bend the power cord sharply.
Battery charge
terminal
Red lamp Battery level
Remain lit Full
Flash continuously Halfway
Two short flashes twice Low
One short flash twice Need to charge
About Bluetooth
Bluetooth is a short-range wireless radio communication technology for
the mobile device such as cellular phones, portable PCs, and other devices.
The Bluetooth devices can be connected without cables and communicate
each other.
About Bluetooth Profile
Bluetooth Profile designates the way of communication between Bluetooth
devices. The system supports the following Bluetooth Profiles.
A2DP: Advanced Audio Distribution Profile
The profile controls sending/receiving the high-quality audio contents.
AVRCP: Audio/Video Remote Control Profile
The profile controls the functions of audio/video devices such as playing,
stopping, pausing and volume control.
HSP: Headset Profile
The profile controlling the cell phone, and controlling the connection
between the devices.
HFP: Hands-Free Profile
The profile controls the hands-free call with cell phone.
About pairing
Pairing creates a unique and encrypted link between two Bluetooth devices
and lets them communicate with each other. Bluetooth devices will not
work if the devices have not been paired.
Cautions on Bluetooth communication
• Microwaves emitted from Bluetooth devices may affect the operation
of electronic medical devices. Turn off this unit and other Bluetooth
devices in hospitals, airplanes, trains, or crowding places.
• Bluetooth devices use 2.4 GHz band, which is the same as that used by
wireless LAN devices and microwave oven. Interference may occur
near these devices and cause noise, disconnectivity, or a decrease of
communication speed.
• Connection with all Bluetooth devices cannot be guaranteed.
Connectivity, operation, display indication or function may differ
depending on the characteristics and specification of the devices.
• Some Bluetooth devices take more time to establish connection.
• To use the Bluetooth functions, the Bluetooth devices are required to be
compatible with the same Bluetooth profiles as this unit is. However, the
functions may differ depending on the specifications of the Bluetooth
device even when it is compatible with the same profiles.
LED flashing patterns
Status LED Flashing pattern
While pairing Blue ●-●-●-●-●-●-●-●-●-●-●-●-●-
Red ●-●-●-●-●-●-●-●-●-●-●-●-●-
Connecting Blue ●-●-●--------------●-●-●----------
Red ------------------------------------------
Communicating Blue ●---------------------●-----------------
Red ------------------------------------------
1. To reduce the risk of electrical shocks, fire, etc.:
● Do not remove screws, cover or cabinet.
● Do not expose this appliance to rain or moisture.
2. For your safety…
● Never use the unit when driving a car, motorcycle, or bicycle. This
could result in an accident.
● Pay special attention to traffic around you when using the
headphones outside. Failure to do so could result in an accident.
● Be careful not to turn up the sound volume too high. Your hearing
can be damaged from listening to sounds at excessive volume for
long periods.
● Do not disassemble or modify the unit.
● Do not allow flammable, water or metallic objects to enter the unit.
● If you find skin problems where the headphones are in contact
with the skin, stop using the headphones; otherwise, it may cause
inflammation or irritation to the skin.
● In dry air such as in winter, you may feel a static shock when using
the headphones.
3. Avoid using the headphones…
● in places subject to excessive humidity or dust
● in places subject to extremely high (over 40°C or 104°F) or low
(under 0°C or 32°F) temperatures
4. DO NOT leave the unit…
● exposed to direct sunlight
● near a heater
5. To protect the unit, DO NOT…
● allow them to get wet
● shake them or drop them against hard objects
Thank you for purchasing this JVC product. Before you begin operating this unit, please read the operating instructions carefully to be sure you get
the best possible performance. If you have any questions, consult your JVC dealer.
6. For using the headphones…
● Attach the ear pieces firmly when replacing them; otherwise, the ear
pieces may be left in your ears when taking the headphones off. If the
ear piece is left in your ear, be careful not to push it deep into the ear
canal.
Be careful not to apply the power that exceeds the headphones’ input
capacity. This may result in sound distortion and could damage the
oscillation board.
Grasp and pull the plug itself to disconnect the headphones. Do not pull
on the cord.
When the ear pieces get dirty, detach the ear pieces and wash them in
water-diluted detergent. After washing, dry the ear pieces and attach to
the headphones.
Replace the ear pieces when: they lose its elasticity; they are stained
badly; they are broken or deformed.
The ear pieces will deteriorate with age even in normal use and
maintenance.
Store the ear pieces in a place where children cannot reach to avoid the
risk of the accident such as swallowing them.
● When using canal type headphones, you may hear the sound of cord
rubbing together or the sound of vibrations which travels through your
body when walking.
7. For safe use of battery…
● Use only the supplied charging unit to charge the battery.
● Be sure to use the supplied AC adaptor.
● There are no serviceable parts inside. Consult your dealer to replace
the built-in battery.
● When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of these
batteries must be followed strictly.
Spanish
Listening to Music
Preparation:
• Make sure that the Bluetooth device can transmit music through the
Bluetooth connection (compatible with the A2DP profile of Bluetooth)
• Finish pairing between the unit and the Bluetooth device.
• Turn on the Bluetooth device.
1 Turn on the unit.
2 Execute the Bluetooth (A2DP) connection on the
Bluetooth device.
• Refer also to the instruction manual supplied for the target device.
• If the connection is not completed within five minutes, this unit goes
to power saving mode. In this case, repeat the procedure from step 1.
3 Start playback on the Bluetooth device.
• Set the connected Bluetooth device so that the device emits the sound
through the Bluetooth stereo headphones.
4 Adjust the volume by tilting the control switch up or
down.
Basic controls available for the device:
Button Press Press and hold
6Play/pause Stop*
¢Skip (to the next) Search (to forward)*
4Skip (to the previous) Search (to backward)*
* Not available for some devices.
• You can perform some of the Bluetooth device operations with
the control switch of the unit if the device is compatible with the
AVRCP profile. The operations you can do may vary depending on
the device you use. Refer also to the instruction manual supplied for
the target device to see the available operations.
To stop using the unit
Disconnect the Bluetooth connection on the Bluetooth device and turn off
the unit.
For the better sound and comfort fit of the headphones
The medium-size ear pieces are attached to the supplied headphones
when purchased.
You may not enjoy the bass sound fully if the ear pieces are not fit
to your ears. To enjoy better sound while reducing sound leakage
and getting full noise canceling effect, choose the ear pieces from
the supplied three sizes (Small, Medium, or Large) and adjust their
positions to fit them to your ears.
Troubleshooting
What appears to be trouble is not always serious. Check the following
points before consult your JVC dealer.
Cannot pair the devices.
☞ You cannot pair the Bluetooth device having receiving function only.
☞ Bring the devices as closer as possible.
Cannot connect the devices.
☞ Pairing is incomplete. Perform the pairing again.
☞ Check that the Bluetooth communication function is activated in the
Bluetooth device.
The sound is intermittent/The communication range is small.
☞ Although Bluetooth wireless technology can transmit the contents
within the range of approx. 10 m, obstacles (human bodies, metallic
objects, wall, etc.) or radiowave condition may affect the sound and
decrease its range.
☞ The sound may be intermittent in the following cases. Avoid the
following conditions when you use this unit.
– Places where the wireless local area network is applied.
– Near the microwave oven.
– Near the other Bluetooth devices.
– Places where the radiowave is used.
No sound.
☞ The connection between the Bluetooth device and this unit is
incomplete. Connect the devices again.
☞ The setting of the Bluetooth device is incorrect. Set the connected
Bluetooth device so that the device emits the sound through the
Bluetooth stereo headphones.
Battery disposal
When disposing the unit, take off the built-in lithium-ion battery and
dispose appropriately for environmental protection.
1. Take off the screws with the
Phillips-head screwdriver.
2. Open the case and take off the
battery.
• Do not take off the battery from its case
when you dispose of the battery.
Calling through the unit
Preparation:
• Activate the Bluetooth communication function on your cellular phone.
• Finish pairing between the unit and your cellular phone.
1 Turn on the unit.
2 Execute the Bluetooth connection on the cellular phone.
• Refer also to the instruction manual supplied for the cellular phone.
• When using a cellular phone supports both HFP and HSP Bluetooth
Profile, use HFP for this unit.
• When the connection is completed, the blue lamp flashes repeatedly.
Basic controls available for the cellular phone connected with HFP:
Status CALL button
Press Press and hold
Waiting Start voice dialing Redial
Dialing by
voice dialing
Cancel voice dialing —
Calling Cancel calling —
Incoming Answer the call Reject the call
Answering Finish the call Switch the device
(between cellular phone
and audio device)
Basic controls available for the cellular phone connected with HSP:
Status CALL button
Press Press and hold
Waiting — Start calling*1
Calling Cancel calling*1Cancel calling or activate
the audio player*2
Incoming Answer the call —
Answering Finish the call*3Activate the audio
device
*1 Not available on some cellular phones.
*2 Varies depending on the model of the cellular phone.
*3 When answering a call on cellular phone, the function may not work.
To make a call while playing back music
When connecting the cellular phone by using HFP or HSP Bluetooth
Profile, you can make a call by using the cellular phone.
To answer a call while playing back music
When a call comes in, the playback sound turns to ring tone. Press the
CALL button to answer the call.
To finish the call
Press the CALL button. The playback sound comes back. (The playback
sound may not come back in some cellular phone.)
You can register up to 8 Bluetooth devices to the unit.
• The device that has the oldest connection date will be overwritten when
you register a 9th Bluetooth device.
Before pairing...
• Make sure that the unit is turned off.
• Turn on the target Bluetooth device and place it within 1 m from the
unit.
1 Turn on the unit with pressing and holding the CALL
button to make it in the pairing mode.
The blue lamp and the red lamp will start flashing continuously as the
unit finds the target Bluetooth device (pairing mode). Release the CALL
button after the flashing starts.
• Finish the steps below within about 3 minutes after the flashing
starts (the pairing mode is automatically cancelled after the period).
Turn off the unit and start from step 1 again when you cannot finish
the operation.
2 Execute pairing operation on the target Bluetooth device
to find the unit.
The device shows the list of Bluetooth devices found. The unit is
recognized as “JVC HA-W700BT”. Repeat from Step 1 again when
“JVC HA-W700BT” is not found.
• Refer also to the instruction manual supplied for the target device.
Registering a Bluetooth device – Pairing
3 Select “JVC HA-W700BT” on the target Bluetooth
device.
4 Enter “0000” when the Pass code* is requested on the
target Bluetooth device.
Pairing is finished when the red lamp goes out and the blue lamp
flashes three times repeatedly.
* also called as “pass key”, “PIN code”, “PIN number”, etc.
5 Execute Bluetooth connection to the unit on the target
Bluetooth device.
The unit saves the target as the last connected Bluetooth device.
• Refer also to the instruction manual supplied for the target device.
• Some Bluetooth device will automatically connect with the unit after
pairing is finished.
• When the connection is completed, the blue lamp flashes repeatedly.
To pair with devices which cannot show the Bluetooth device list...
On some Bluetooth devices, pairing may automatically be established by
making both the unit and the target device in the pairing mode. Refer also
to the instruction manual supplied for the target device to make it in the
pairing mode.
CAUTION
Specifications
General
Bluetooth version: Bluetooth 2.0 certified
Output power: Bluetooth power class 2
Service area: max. 10 m (10.9 yd.) (approx.)*
* Communication range may vary depending on the environmental
conditions.
Frequency band: 2.4 GHz (2,4000 GHz – 2,4835 GHz)
Bluetooth profile:
A2DP (Advanced Audio Distribution Profile), AVRCP (Audio/Video
Remote Control Profile), HFP (Hands-free Profile), HSP (Headset
Profile)
Supported Codec: SBC
Power supply: Built-in lithium-ion rechargeable battery (DC 3.7 V)
Battery life*: Music play time: max. XXX hours
Standby time: max. XXX hours
* Depends on use.
Mass: 35 g (1.23 oz.) (including headphones)
Headphones (J48139-001)
Frequency response: 10 Hz – 23,000 Hz
Sensitivity: 93 dB/1 mW
Accessories
AC adaptor x 1 (S004CU0500050), Ear pieces (3 pairs, L, M, S), Charging
unit (J48140-001) x 1
Designs and specifications are subject to change without notice.
The Bluetooth® word mark and logos are registered trademarks owned
by Bluetooth SIG, Inc. and any use of such marks by Victor Company of
Japan, Limited (JVC) is under license. Other trademarks and trade names
are those of their respective owners.
Parts name
1
8
234 5
67
9p
q
1 (CALL) button
Controls the cellular phone calling through this unit.
2 Control switch*
Controls the music player connected with this unit.
3 Red lamp
Indicates the battery status of this unit.
4 Blue lamp
Indicates the communication status between this
unit and Bluetooth equipment.
5 Microphone
Picks up your voice when calling through this unit.
6 Strap hole
7 Stereo mini jack
8 Headphones
9 Battery charge terminal
p Clip
q POWER switch
Slides to turn on or off this unit.
* The volume level of the connected device cannot be
changed from this unit.
Battery
Features
This unit is a wireless stereo headset using Bluetooth® wireless technology.
Call Call
Control Control
iPod with Bluetooth
Transmitter
Bluetooth cell phone
As Bluetooth Stereo Headset As Bluetooth Receiver
Control
Music & Call
Bluetooth cell phone
with music player Bluetooth audio source
Music
• Checking the battery charge
Press the PLAY/PAUSE button while holding the CALL button. (Press the
PLAY/PAUSE button within two seconds after pressing CALL button.)
The red lamp lights or flashes to show the battery remains.
• The red lamp starts slow flashing automatically when the battery
become nearly empty.
Battery charging
Charge the built-in rechargeable lithium-ion battery first to use this unit.
1 Connect the AC adaptor to the charging unit.
• Do not use any AC adaptor other than the supplied one.
2 Connect the AC adaptor to the AC outlet.
3 Put the unit on the charging stand.
The red lamp lights up when the battery charge terminals contact.
The blue lamp will light up when the charging is finished (the red lamp will
turn off).
• It takes about three hours to charge the battery to full when it is empty.
• You can use the unit while charging.
• Disconnect the AC adaptor from the AC outlet when you do not use the
charging unit for a extended period of time.
• Do not pull the cord when disconnecting the AC adaptor.
• Do not handle the power cord with wet hands!
• Do not bend the power cord sharply.
Battery charge
terminal
Red lamp Battery level
Remain lit Full
Flash continuously Halfway
Two short flashes twice Low
One short flash twice Need to charge
About Bluetooth
Bluetooth is a short-range wireless radio communication technology for
the mobile device such as cellular phones, portable PCs, and other devices.
The Bluetooth devices can be connected without cables and communicate
each other.
About Bluetooth Profile
Bluetooth Profile designates the way of communication between Bluetooth
devices. The system supports the following Bluetooth Profiles.
A2DP: Advanced Audio Distribution Profile
The profile controls sending/receiving the high-quality audio contents.
AVRCP: Audio/Video Remote Control Profile
The profile controls the functions of audio/video devices such as playing,
stopping, pausing and volume control.
HSP: Headset Profile
The profile controlling the cell phone, and controlling the connection
between the devices.
HFP: Hands-Free Profile
The profile controls the hands-free call with cell phone.
About pairing
Pairing creates a unique and encrypted link between two Bluetooth devices
and lets them communicate with each other. Bluetooth devices will not
work if the devices have not been paired.
Cautions on Bluetooth communication
• Microwaves emitted from Bluetooth devices may affect the operation
of electronic medical devices. Turn off this unit and other Bluetooth
devices in hospitals, airplanes, trains, or crowding places.
• Bluetooth devices use 2.4 GHz band, which is the same as that used by
wireless LAN devices and microwave oven. Interference may occur
near these devices and cause noise, disconnectivity, or a decrease of
communication speed.
• Connection with all Bluetooth devices cannot be guaranteed.
Connectivity, operation, display indication or function may differ
depending on the characteristics and specification of the devices.
• Some Bluetooth devices take more time to establish connection.
• To use the Bluetooth functions, the Bluetooth devices are required to be
compatible with the same Bluetooth profiles as this unit is. However, the
functions may differ depending on the specifications of the Bluetooth
device even when it is compatible with the same profiles.
LED flashing patterns
Status LED Flashing pattern
While pairing Blue ●-●-●-●-●-●-●-●-●-●-●-●-●-
Red ●-●-●-●-●-●-●-●-●-●-●-●-●-
Connecting Blue ●-●-●--------------●-●-●----------
Red ------------------------------------------
Communicating Blue ●---------------------●-----------------
Red ------------------------------------------
HA-W700BT_J.indd 2HA-W700BT_J.indd 2 07.8.1 2:39:16 PM07.8.1 2:39:16 PM