Junlan Electronic IOTS1010 SMART PLUG User Manual 1
Shenzhen Junlan Electronic Ltd SMART PLUG 1
Users manual
![](/img.php?id=3923781&img=bg1.png)
PLEASE READ CAREFULLY BEFORE OPERATING THIS EQUIPMENT
KEEP IT IN A SAFE PLACE FOR FUTURE REFERENCE
BASIC WIFI SMART PLUG
MODEL:AWP48W
![](/img.php?id=3923781&img=bg2.png)
2
DANGEROUS VOLTAGE:The lighting flash with arrowhead symbol within
an equilateral triangle is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock to persons.
ATTENTION:The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
WARNING: USE UNDER SUPERVISION OF AN ADULT DUE TO LONG
CORD This unit has a long cord that can be easily tripped on or pulled on,
causing injury. Please make sure it is arranged so that it will not drape over a
tabletop, etc. Where it can be pulled on by children or tripped over accidentally.
FCC STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THE
COVER (OR BACK). NO USER SERVICEABLE PART INSIDE, REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
![](/img.php?id=3923781&img=bg3.png)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING:
To assure continued operation, follow the attached installation instructions and
use only shield cables when connecting to other devices. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Before using the unit, be sure to read all operating instruction carefully, please
note that these are general precautions and may not pertain to your unit. For
example, this unit may not have the capability to be connected to an outdoor
antenna.
1. Read these instructions
All the safety and operating instructions should be read before the appliance is
operated.
2. Keep these instructions
The safety and operating instructions should be kept for future reference.
3. Heed all warnings
All warnings on the appliance and in the operating instructions should be
adhered to.
4. Follow all instructions
All operation and use instructions should be followed.
FCC NOTICE:
5. Do not use this apparatus near water
The appliance should not be used near water; for example, near a bath tub,
3
![](/img.php?id=3923781&img=bg4.png)
4
washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming
pool.
6. Clean only with dry cloth
The appliance should be cleaned only as recommended by the manufacturer.
7. Do not block any ventilation openings.Install in accordance with the
manufacturer’s instructions.
Slots and openings in the cabinet and in the back or bottom are provided for
ventilation, to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or similar
surface. This product should never be placed near or over a radiator or heat
source. This product should not be placed in a built-in installation, such as a
bookcase or rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide or the third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments / accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury
from tip-over.
An appliance and cart combination should be moved with care. Quick stop,
excessive fore and uneven surfaces may cause the appliance and cart
combination to overturn.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
To protect your product from a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the product due to
lightning and power-line surges.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or
![](/img.php?id=3923781&img=bg5.png)
moisture, does not operate normally, or has been dropped.
15. Power source
This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company. For products
intended to operate from battery power, or other source, refer to the operation
instructions.
16. Power lines
An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of
fire or electric shock.
18. Object and liquid entry
Never push objects of any kind into the product through openings as they may
touch dangerous voltage points or short out parts that could result in fire or
electric shock. Never spill or spray any type of liquid on the product.
19. Outdoor antenna grounding
If an outside antenna is connected to the product, be sure the antenna system
is grounded so as to provide some protection against voltage surges and built
up static charges. Section 810 of the National Electric Code ANSI/ NFPA 70
provides information with respect to proper grounding of the mast and
supporting structure, grounding of the lead- in wire to an antenna discharge
product, size of grounding conductors, location of antenna- discharge product,
connection to grounding electrodes and requirements for the grounding
electrodes.
5
![](/img.php?id=3923781&img=bg6.png)
20. Service
Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
b)If liquid has been spilled or objects have fallen into the product.
c)If the product has been exposed to rain or water.
d)If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions, as an adjustment of other controls may result in damage and will
require extensive work by a qualified technician to restore the product to its
normal operation.
e)If the product has been dropped or the cabinet has been damaged.
f)When the product exhibits a distinct change in performance- this indicates a
need for service.
25. Note to CATV system installer
This reminder is provided to call the CATV system installer' s attention to
Article 820- 40 of the NEC that provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as
practical.
NOTE: Refer all servicing to qualified service personnel. Servicing is
required when the unit has been damaged in any way such as the
following: the power-supply cord or plug has been damaged, liquid has
been spilled into unit, the unit has been exposed to rain or moisture, the
unit has been dropped or the unit does not operate normally.
21. Replacement parts
When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or those that have the same
characteristics as the original parts. Unauthorized substitutions may result in
fire or electric shock or other hazards.
22. Safety check
Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper
operating condition.
23. Wall or ceiling mounting
The product should be mounted to a wall or ceiling only as recommended by
the manufacturer.
24. Damage requiring service
Unplug this product from the wall outlet and refer service to qualified service
personnel under the following conditions.
a)When the power- supply cord or plug is damaged.
6
![](/img.php?id=3923781&img=bg7.png)
7
SMART SOCKET OVERVIEW
Socket
Power ON/OFF Button
LED Ring
Press and hold the power button for about
5 seconds in powering on mode, the LED
LED ring will turn red.
Press the power button to power on, the
Press the power button again to power off
PREPARATION
Smooth and rapid Wi-Fi network (2.4 GHz only)
Smart Life APP and account
One Smart Device: smart phone or tablet (not included)
the LED ring will turn off.
ring blinks fast with red and blue color,
now it is in pairing mode(EZ mode).
Press and hold the power button for about
5 seconds in pairing mode until the LED
ring blinks slowly with blue color, now it is
in compatible pairing mode (AP mode).
LED Ring Color Smart Socket Status
Red Powering On
No Color Powering Off
Blue and Red or Blue
(blink fast) Pairing mode (EZ mode)
Blue and Red or Blue
(blink slowly) Compatible pairing mode
(AP mode)
![](/img.php?id=3923781&img=bg8.png)
SMART LIFE APP
1. Search "Smart Life" on Apple APP store or Google Play, download and install it.
2. Once installed successfully, the icon will appear as the figure below.
REGISTER SMART LIFE APP
1. Tap the Smart Life App icon to open.
Smart Life
2. Tap "Register". (If you already have an account, tap "Login" to log in)
3. Tap the country columnn to select your country.
4. Tap "Mobile Number/Email" column to input your mobile phone number or email
address. Tap "Next" to continue.
6. Tap "Confirm" to finish registration.
5. A verification code will be sent to your mobile phone or inbox on your phone.
Input the verification code into the "verification code" column, then input a
password on " Please Input Password" column.(6-20 digit password with letter
and number)
8
![](/img.php?id=3923781&img=bg9.png)
9
CONNECT SMART SOCKET BY SMART LIFE APP
1. Click "Smart Life" App and log in.
When the below page appear,
click "Add device" to continue.
2. When the below page appear,
click "Electrical outlet" to continue.
3. Press and hold the button for approx.10 seconds until the LED ring turns Blue and Red
and blinking fast, click "Confirm indicator rapidly blink" to continue.
CONNECTION THROUGH EZ MODE
![](/img.php?id=3923781&img=bga.png)
10
4. The window will remind you to confirm
the Wi-Fi information.
"Confirm" to continue.
Input the Wi-Fi password and tap
5. The Smart Life is now connecting
the available smart outlets.
IMPORTANT!
ONCE DEVICE ADDED,
CLICK TO RENAME,
OTHERWISE, IT CAN NOT
BE CONTROLLED BY ALEXA
VOICE CONTROL.
6. The available smart outlets will be shown as below when successfully connected.
![](/img.php?id=3923781&img=bgb.png)
11
7. After renaming, tap "Share with family"
family can control on their smart phone with Smart Life APP.
and set as on screen instructions to share with
family, then your
Or you can set it later and tap "Done" to continue.
8. If connection fails, tap "Retry" to reconnect again as above steps.
![](/img.php?id=3923781&img=bgc.png)
CONNECTION THROUGH AP MODE
12
1. Click "Smart Life" App and log in.
When the below page appear,
click "Add device" to continue.
2. When the below page appear,
click "Electrical outlet" to continue.
3. Press and hold the button for approx.15 seconds until the LED ring turns Blue and Red
then it turns blue and blinking slowly, tap "AP Mode" to skip to next interface.
![](/img.php?id=3923781&img=bgd.png)
13
4. Tap "Confirm indicator slowly blink" to continue. 5. The window will remind you to confirm
the Wi-Fi information.
"Confirm" to continue.
Input the Wi-Fi password and tap
6. Tap "Connect Now" to skip to your
smart phone's wifi setting. 7. Select SmartLift-XXXX then return to APP.
![](/img.php?id=3923781&img=bge.png)
9. The available smart outlets will be shown as below when successfully connected.
IMPORTANT!
ONCE DEVICE ADDED,
CLICK TO RENAME,
OTHERWISE, IT CAN NOT
BE CONTROLLED BY ALEXA
VOICE CONTROL.
14
8. The Smart Life is now connecting
the available smart outlets.
![](/img.php?id=3923781&img=bgf.png)
10. After renaming, tap "Share with family"
family can control on their smart phone with Smart Life APP.
and set as on screen instructions to share with
family, then your
Or you can set it later and tap "Done" to continue.
15
11. If connection fails, tap "Retry" to reconnect again as above steps.
![](/img.php?id=3923781&img=bg10.png)
HOME PAGE
1. After completely connection, the home page will appear as below.
appear as below.
2. Tap "+" at the right top corner to add more device, the connection procedures refer to the
previous two connection menthod, after successful addition, the interface will
16
![](/img.php?id=3923781&img=bg11.png)
HOME PAGE
3. Tap "Scenes" at the bottom of the screen to create your own scene to suit your needs,
For example, set your home to automatically turn on the lights and close.
4. Tap "+" to add your customized scene, here, tap "Good night", then you need to finish two
steps, step1: add a condition, step2: add a task (if there is no device added, here will be empty,
and you need to add a device before this operation).
when finish two steps, the "Perform" will be green, and you can tap "Perform" to execute task.
17
![](/img.php?id=3923781&img=bg12.png)
HOME PAGE
5. Tap "Profiles" at the bottom of the screen to set your profile, create scenes, sharing device,
receiving message, using integration(the third side software) to operate by voice control or other
operations, tap "Experience Center" to experience the scene, tap "Scan QR Code" to scan the
QR code on some of the smart product, tap FAQ to check the requent ask questions.
NOTE: For Integration, here you can operate as the screen instructions to operate, expecially
you can use Amazon Alexa for voice control operation.
18