Kar Tech MOD153 2.4GHz modular transceiver User Manual User s manual
Kar-Tech, Inc. 2.4GHz modular transceiver User s manual
Kar Tech >
User manual
MOD153 2.4GHz MODULAR TRANSCEIVER OEM INSTALLATION AND OPERATION MANUAL NOTE: THIS MODULE IS LIMITED TO OEM INSTALLATION ONLY December 8, 2015 HK MOD153 TRANSCEIVER INDEX DESCRIPTION........................................................................... 2 OPERATION .............................................................................. 2 INSTALLATION ......................................................................... 3 BEFORE APPLYING POWER!...................................................... 4 TROUBLESHOOTING ................................................................. 5 TRANSCEIVER PICTORIAL ........................................................ 6 INSTRUCTION TO THE USER ..................................................... 7 INDUSTRY CANADA STATEMENTS............................................. 9 EUROPE .................................................................................. 12 MOD153 TRANSCEIVER frequency synthesizer, a power DESCRIPTION The MOD153 sequence is spread amplifier, a modulator and a direct receiver spectrum transceiver module designed to free use in the 2.4 GHz ISM the The transmit be used simultaneously to circuitry. The RF section runs on the 3.3V supply. The MOD153 is Direct Sequence is Spread Spectrum that can use radio one 16 channels, is integrated where 2.405GHZ Channel 16 is 2.480 GHZ. microcontroller includes a CPU, fully of Channel GHz ISM bands. The transceiver The constant 1.8 VDC for the digital with transceiver module for the 2.4 GPI/O, communication. DC regulator which generates a OPERATION MOD153 is MOD153 transceiver contains a any other transmitter. The The data is microcontroller entire applications not via responsible for the control of the The MOD153 is not designed for should host the serial port and to the host. MOD153 transceiver. and the to is received from antenna is sent to Kar-Tech. There are no user antenna connected port to the antenna and the data control products by Kar-Tech, at multiple serial processor and then to RF circuit integrated into Kar-Tech remote on microcontroller MOD153 sent through a serial port to RF The MOD153 transceiver is only parts The protection circuits. band. serviceable unit. and MOD153 TRANSCEIVER The receivers are matched to C) The antenna should be the transmitters to use the same mounted at least 20cm channel from as the transmitter’s all persons, and signals. must INSTALLATION simultaneously with any 1) Solder the other MOD153 transceiver directly to the host’s compatible connector. not transmit antenna or transmitter, except accordance with in FCC multi transmitter product 2) Print and attach the label procedures. as shown below: D)The MOD153 is to be installed only in mobile applications. operate the Do not MOD153 without an antenna. 3) Connect the E) Documentations: appropriate host’s antenna. In User the Manual include the following: Application Requirements: a. That there are no user serviceable parts Transceiver with 3.3VDC the modules. nominal They A) Power peak the MOD153 voltage, current with draw radio should in not remove or install radio of modules. 150mA. b. The B) Do not remove the shield “Instructions The User” section. on the MOD153. To MOD153 TRANSCEIVER c. The “Industry Canada Statement”. d. Include in the manual, “This device is granted for use in Mobile only configurations which used the antennas for transmitter in must this be installed to provide a separation distance of at least 20cm from all person and not be colocated with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter product procedures.” BEFORE APPLYING POWER! x Check power and ground for proper polarity. x Read the rest of this manual. MOD153 TRANSCEIVER TROUBLESHOOTING There are no user serviceable parts in the MOD153 Transceiver. Contact your representative KAR-TECH for further instructions or servicing. There are no user-serviceable parts inside the transmitter or the receiver. Return the units for service. The information, specifications, and illustrations in this manual are those in effect at the time of printing. We reserve the right to change specifications or design at any time without notice. MOD153 TRANSCEIVER TRANSCEIVER PICTORIAL TRANSCEIVER Power supply ........................................................................... 3.3VDC Operating temperature - Radio....................................... -20˚C to +55˚C Storage temperature .................................................. -40˚C to +100˚C RF Frequency ............................................................... 2.405-2.48 GHz Antenna Manufacturer …………………………………………………………….. Kar-Tech, Inc. Antenna Model………………………………………………………………………………….. MOD153 Antenna Gain……………………………………………………………………………………….. 1.1dBi MOD153 TRANSCEIVER INSTRUCTION TO THE USER This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not MOD153 TRANSCEIVER be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: P4UMOD153 when the module is installed inside another device, the user manual of this device must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product MOD153 TRANSCEIVER INDUSTRY CANADA STATEMENTS This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée quivalente (p.i.r.e.) ne dépassepas l'intensité nécessaire à l'établissement d'une communication satisfaisante. MOD153 TRANSCEIVER OEM Responsibilities to comply with FCC and Industry Canada Regulations This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes : ( 1 ) Ce dispositif ne peut causer d'interférences ; et ( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. IC Radiation Exposure Statement The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden. This modular complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. Cette modulaire doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et le corps de l'utilisateur. If the IC number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 4534A-MOD153ā when the module is installed inside another device, the user manual of this device must contain below warning statements; 10 MOD153 TRANSCEIVER 1. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. 2. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes : ( 1 ) Ce dispositif ne peut causer d'interférences ; et ( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. 11 MOD153 TRANSCEIVER EUROPE CE NOTICE This device has been tested and certified for use in the European Union. See the Declaration of Conformity (DOC) for specifics. If this device is used in a product, the OEM has the responsibility to verify compliance of the final product to the EU standards. A declaration of Conformity must be issued and kept on file as described in the Radio and Telecommunications Terminal Equipment (R&TTE) Directive. The ‘CE’ mark must be placed on the OEM product per the labeling requirements on the Directive. Declaration of Conformity (DOC) This DOC can be downloaded from the www.kar-tech.com. The device complies with RF specifications when the device used at your body. Caution: Must use the original antenna. Other antennas are not allowed to be used. The device according to the regulation in Directive 1999/5/EC and complies with standards as follow: EMC (Article 3.1b) ETSI EN 301 489-1 V 1.9.2 ETSI EN 301 489-17 V2.2.1 (2012-09) Report No.: CTL1512313913-WE Radio (Article 3.2) ETSI EN 300 328 V1.8.1 Report No.: CTL1512313913-WR EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 EN 62479: 2010 Report No.: CTL1512313913-WS Report No.: CTL1512313913-WH Safety (Article 3.1a) Health (Article 3.1a) [Titles, dates of publication of documents mentioned ] 12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Administrator Create Date : 2016:02:03 14:48:06+08:00 Modify Date : 2016:02:03 14:48:06+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Producer : Acrobat Distiller 9.0.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Metadata Date : 2016:02:03 14:20:31+08:00 Format : application/pdf Title : Microsoft Word - User's manual.doc Creator : Administrator Document ID : uuid:339a2e50-7187-448e-a421-b6526be8e246 Instance ID : uuid:86202348-0be1-4628-86ae-d5e61bcb473c Page Count : 13EXIF Metadata provided by EXIF.tools