MGA Entertainment 513049 Mini Lalaloopsy RC Car (49MHz) User Manual 510291 Mini Lalaloopsy RC Car 1 4
MGA Entertainment (HK) Ltd. Mini Lalaloopsy RC Car (49MHz) 510291 Mini Lalaloopsy RC Car 1 4
users manual
TROUBLESHOOTING: IF THERE IS NO FUNCTION BETWEEN THE REMOTE CONTROL AND THE CRUISER: • Make sure the Remote Control and the Cruiser switches are in the “ON” position. • Make sure the batteries are inserted properly. • Replace the old batteries with new alkaline batteries. • Move the Remote Control closer to the Cruiser to determine the best communication between the two. TM FCC COMPLIANCE NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation. Age 4+ years Adult Battery Installation Required Item No. 513032 – 27 MHz Item No. 513049 – 49 MHz INTRODUCTION Start your engines! Because now your Mini’s can cruize to the silly, wonderful world of Lalaloopsy™ in their very own Cruiser! CONTENTS a) 1 Mini Lalaloopsy™ RC Cruiser b) 1 Remote Control c) 1 Mini Lalaloopsy™ Charlotte Charades™ Doll Warning : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. SAFE BATTERY USAGE • Use alkaline batteries for best performance and longer life. • Use only the type battery recommended for the unit. • Batteries should be replaced only by an adult. • Insert batteries with the correct polarity ( + and – ). • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zinc), or rechargeable(nickel-cadmium) batteries. • Do not short-circuit batteries. • When not used for an extended time, remove batteries to prevent possible leakage and damage to the unit. • Do not mix rechargeable and non-rechargeable batteries. • Rechargeable batteries are to be removed from the toy before charging. • Rechargeable batteries are to be recharged only under adult supervision. • Do not recharge non-rechargeable batteries. • Exhausted batteries are to be removed from the toy. • Do not dispose of batteries in fire as they may leak or explode. c. a. b. ‘Let’s care for the environment!’ The wheelie bin symbol indicates that the product must not be disposed of with other household waste. Please use designated collection points or recycling facilities when disposing of the item. Do not treat old batteries as household waste. Take them to a designated recycling facility. Please keep this manual as it contains important information. 0811-0-E www.lalaloopsy.com © MGA Entertainment, Inc. LALALOOPSY™, MINI LALALOOPSY™ and LALALOOPSY LITTLES™ are trademarks of MGA in the U.S. and other countries. All logos, names, characters, likenesses, images, slogans, and packaging appearance are the property of MGA. 16300 Roscoe Blvd. Van Nuys, CA 91406 U.S.A. (800) 222-4685 Printed in China Illustrations are for reference only. Styles may vary from actual contents. BEFORE YOU BEGIN 1.5V AA / LR06 1.5V AAA/LR03 OFF 1.5V AA / LR06 ON 1.5V AA / LR06 An ADULT must install batteries in the Cruiser. Here’s how: 1. Switch the ON/OFF switch to “OFF.” Using a Phillips screwdriver (not included), remove the screw and battery compartment cover located on the bottom of the Cruiser. (Fig. 1) 2. Install three (3) AA alkaline batteries (not included) making sure the (+) and (-) ends face the proper direction as indicated inside the battery compartment. 3. Replace the compartment cover and tighten the screw. 1.5V AAA/LR03 OPERATING THE CRUISER CRUISER 1. Slide the ON/OFF switch on the bottom of the Cruiser to the “ON” position. 2. Slide the ON/OFF switch on the back of the Remote Control to the “ON” position. 3. Place the Cruiser on a flat, level surface. 4. Straighten the Antenna. 5. Use the Remote Control to drive your Cruiser by doing the following: a. Press down on the left side of the Remote Control to go forward. (Fig. 5) b. Press down the right side of the Remote Control to back up and turn to the left. (Fig. 6) Fig. 1 ON OFF REMOTE CONTROL An ADULT must install batteries in the Remote Control. Here’s how: 1. Switch the ON/OFF switch to “OFF.” Using a Phillips screwdriver (not included) remove the screw and battery compartment cover on the back of the Remote Control. (Fig. 2) 2. Install two (2) AAA alkaline batteries (not included) making sure the (+) and (-) ends face the proper direction as indicated inside the battery compartment. (Fig. 2) 3. Replace the compartment cover and tighten the screw. Fig. 5 Fig. 6 IMPORTANT INFORMATION Fig. 2 • When driving two RC Cruiser, they must be of different radio frequencies (e.g. one Cruiser 49MHz and one Cruiser 27MHz) or they may not perform as designed. • When Cruiser is not being played with, turn the ON/OFF switches on both the Cruiser and Remote “OFF” to save battery power. • Your Cruiser is controlled by radio frequency. It may interfere with nearby devices such as cordless phones, hair dryers, radios, walkie-talkies, or other radio controlled devices. If this occurs, move the Cruiser to a location away from the interference. • The Cruiser must remain in remote control range to operate correctly. The range depends on the surrounding area and on the strength of the battery. Obstructions such as buildings, fences, etc., between the remote control transmitter and the Cruiser, reduce the range. • If the Cruiser runs slowly, replace the batteries. • KEEP AWAY FROM WATER! Do not run your Cruiser through puddles, or expose it to liquid of any kind as moisture may damage the unit. FASTEN YOUR SEAT BELTS! Before going for a drive, make sure that your dolls are in place and buckled up: 1. Lift the elastic band. (Fig. 3) 2. Secure your doll in the seat under the elastic band. (Fig. 4) Ready to roll! CAUTION: Fig. 3 Fig. 4 • DO NOT sit or stand on any part of the Cruiser. • DO NOT lift and/or drop the Cruiser as doing so may cause bodily injury to the user and irreparable damage to the Cruiser. • Play with the Cruiser on the floor or ground only. • DO NOT operate this Cruiser during thunderstorms. • Keep hair, fingers, loose clothing and other items away from rotating wheels of the unit. BEFORE YOU BEGIN 1.5V AA / LR06 1.5V AAA/LR03 OFF 1.5V AA / LR06 ON 1.5V AA / LR06 An ADULT must install batteries in the Cruiser. Here’s how: 1. Switch the ON/OFF switch to “OFF.” Using a Phillips screwdriver (not included), remove the screw and battery compartment cover located on the bottom of the Cruiser. (Fig. 1) 2. Install three (3) AA alkaline batteries (not included) making sure the (+) and (-) ends face the proper direction as indicated inside the battery compartment. 3. Replace the compartment cover and tighten the screw. 1.5V AAA/LR03 OPERATING THE CRUISER CRUISER 1. Slide the ON/OFF switch on the bottom of the Cruiser to the “ON” position. 2. Slide the ON/OFF switch on the back of the Remote Control to the “ON” position. 3. Place the Cruiser on a flat, level surface. 4. Straighten the Antenna. 5. Use the Remote Control to drive your Cruiser by doing the following: a. Press down on the left side of the Remote Control to go forward. (Fig. 5) b. Press down the right side of the Remote Control to back up and turn to the left. (Fig. 6) Fig. 1 ON OFF REMOTE CONTROL An ADULT must install batteries in the Remote Control. Here’s how: 1. Switch the ON/OFF switch to “OFF.” Using a Phillips screwdriver (not included) remove the screw and battery compartment cover on the back of the Remote Control. (Fig. 2) 2. Install two (2) AAA alkaline batteries (not included) making sure the (+) and (-) ends face the proper direction as indicated inside the battery compartment. (Fig. 2) 3. Replace the compartment cover and tighten the screw. Fig. 5 Fig. 6 IMPORTANT INFORMATION Fig. 2 • When driving two RC Cruiser, they must be of different radio frequencies (e.g. one Cruiser 49MHz and one Cruiser 27MHz) or they may not perform as designed. • When Cruiser is not being played with, turn the ON/OFF switches on both the Cruiser and Remote “OFF” to save battery power. • Your Cruiser is controlled by radio frequency. It may interfere with nearby devices such as cordless phones, hair dryers, radios, walkie-talkies, or other radio controlled devices. If this occurs, move the Cruiser to a location away from the interference. • The Cruiser must remain in remote control range to operate correctly. The range depends on the surrounding area and on the strength of the battery. Obstructions such as buildings, fences, etc., between the remote control transmitter and the Cruiser, reduce the range. • If the Cruiser runs slowly, replace the batteries. • KEEP AWAY FROM WATER! Do not run your Cruiser through puddles, or expose it to liquid of any kind as moisture may damage the unit. FASTEN YOUR SEAT BELTS! Before going for a drive, make sure that your dolls are in place and buckled up: 1. Lift the elastic band. (Fig. 3) 2. Secure your doll in the seat under the elastic band. (Fig. 4) Ready to roll! CAUTION: Fig. 3 Fig. 4 • DO NOT sit or stand on any part of the Cruiser. • DO NOT lift and/or drop the Cruiser as doing so may cause bodily injury to the user and irreparable damage to the Cruiser. • Play with the Cruiser on the floor or ground only. • DO NOT operate this Cruiser during thunderstorms. • Keep hair, fingers, loose clothing and other items away from rotating wheels of the unit. TROUBLESHOOTING: IF THERE IS NO FUNCTION BETWEEN THE REMOTE CONTROL AND THE CRUISER: • Make sure the Remote Control and the Cruiser switches are in the “ON” position. • Make sure the batteries are inserted properly. • Replace the old batteries with new alkaline batteries. • Move the Remote Control closer to the Cruiser to determine the best communication between the two. TM FCC COMPLIANCE NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation. Age 4+ years Adult Battery Installation Required Item No. 513032 – 27 MHz Item No. 513049 – 49 MHz INTRODUCTION Start your engines! Because now your Mini’s can cruize to the silly, wonderful world of Lalaloopsy™ in their very own Cruiser! CONTENTS a) 1 Mini Lalaloopsy™ RC Cruiser b) 1 Remote Control c) 1 Mini Lalaloopsy™ Charlotte Charades™ Doll Warning : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. SAFE BATTERY USAGE • Use alkaline batteries for best performance and longer life. • Use only the type battery recommended for the unit. • Batteries should be replaced only by an adult. • Insert batteries with the correct polarity ( + and – ). • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zinc), or rechargeable(nickel-cadmium) batteries. • Do not short-circuit batteries. • When not used for an extended time, remove batteries to prevent possible leakage and damage to the unit. • Do not mix rechargeable and non-rechargeable batteries. • Rechargeable batteries are to be removed from the toy before charging. • Rechargeable batteries are to be recharged only under adult supervision. • Do not recharge non-rechargeable batteries. • Exhausted batteries are to be removed from the toy. • Do not dispose of batteries in fire as they may leak or explode. c. a. b. ‘Let’s care for the environment!’ The wheelie bin symbol indicates that the product must not be disposed of with other household waste. Please use designated collection points or recycling facilities when disposing of the item. Do not treat old batteries as household waste. Take them to a designated recycling facility. Please keep this manual as it contains important information. 0811-0-E www.lalaloopsy.com © MGA Entertainment, Inc. LALALOOPSY™, MINI LALALOOPSY™ and LALALOOPSY LITTLES™ are trademarks of MGA in the U.S. and other countries. All logos, names, characters, likenesses, images, slogans, and packaging appearance are the property of MGA. 16300 Roscoe Blvd. Van Nuys, CA 91406 U.S.A. (800) 222-4685 Printed in China Illustrations are for reference only. Styles may vary from actual contents.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Create Date : 2011:08:19 16:50:14+08:00 Creator : Adobe Illustrator CS3 Modify Date : 2011:08:22 19:30:20+08:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Title : 510291 Mini Lalaloopsy RC Car 1-4 Creator Tool : Adobe Illustrator CS3 Metadata Date : 2011:08:22 19:30:20+08:00 Thumbnail Width : 256 Thumbnail Height : 188 Thumbnail Format : JPEG Thumbnail Image : (Binary data 13758 bytes, use -b option to extract) Document ID : uuid:1568EF2615CCE01197DDB8FA25C7931B Instance ID : uuid:0af55759-12d6-4d69-98ec-3ee44c0db91a Derived From Instance ID : uuid:1468EF2615CCE01197DDB8FA25C7931B Derived From Document ID : uuid:E9ABA9DAA6A1E011998585EAAD5F963B Manifest Link Form : EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference Manifest Reference File Path : /Volumes/job/Packing & IM/LALALOOPSY/S12/510291 Mini Lalaloopsy RC Car_FMA/IM/E0:INT-0/RC.jpg, /Volumes/job/Packing & IM/LALALOOPSY/S12/510291 Mini Lalaloopsy RC Cruiser_FMA/IM/E0:INT-0/c.jpg, /Volumes/job/Packing & IM/LALALOOPSY/S12/510291 Mini Lalaloopsy RC Cruiser_FMA/IM/E0:INT-0/b.jpg, /Volumes/job/Packing & IM/LALALOOPSY/S12/510291 Mini Lalaloopsy RC Car_FMA/IM/E0:INT-0/Mini_Lala_Logo.tif, /Volumes/job/Packing & IM/LALALOOPSY/S12/510291 Mini Lalaloopsy RC Cruiser_FMA/IM/E0:INT-0/a.jpg Manifest Reference Instance ID : uuid:D07AF0201CC0E011AD97A385F511B94B, uuid:D07046D842CBE011B6E2E0DF78B3EB1E, uuid:2A2C7ECC42CBE011B6E2E0DF78B3EB1E, uuid:CE7AF0201CC0E011AD97A385F511B94B, uuid:2ABA79224BCBE011B6E2E0DF78B3EB1E Manifest Reference Document ID : uuid:CF7AF0201CC0E011AD97A385F511B94B, uuid:CF7046D842CBE011B6E2E0DF78B3EB1E, uuid:292C7ECC42CBE011B6E2E0DF78B3EB1E, uuid:EC22E2120EC0E011AD97A385F511B94B, uuid:29BA79224BCBE011B6E2E0DF78B3EB1E N Pages : 1 Has Visible Transparency : False Has Visible Overprint : True Max Page Size W : 29.703889 Max Page Size H : 20.990278 Max Page Size Unit : Centimeters Font Name : ComicSansMS-Bold, ComicSansMS, ArialMT Font Family : Comic Sans MS, Comic Sans MS, Arial Font Face : Bold, Regular, Regular Font Type : TrueType, TrueType, Open Type Font Version : Version 2.10, Version 2.10, Version 3.05 Font Composite : False, False, False Font File Name : Comic Sans MS, Comic Sans MS, Arial Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : Default Swatch Group Swatch Group Type : 0 Swatch Colorant Swatch Name : PANTONE 527 C, Black, C=100 M=0 Y=100 K=0 1, C=0 M=0 Y=0 K=100 1 Swatch Colorant Type : SPOT, PROCESS, PROCESS, PROCESS Swatch Colorant Tint : 100.000000, 100.000000 Swatch Colorant Mode : CMYK, CMYK, CMYK, CMYK Swatch Colorant Cyan : 72.999992, 69.803902, 100.000000, 0.000000 Swatch Colorant Magenta : 100.000000, 67.451004, 0.000000, 0.000000 Swatch Colorant Yellow : 0.000000, 63.921600, 100.000000, 0.000000 Swatch Colorant Black : 0.000000, 74.117599, 0.000000, 100.000000 Producer : Adobe PDF library 8.00 Page Count : 4EXIF Metadata provided by EXIF.tools