Northfield Telecommunications d b a Advanced Wireless Communications HD-1000V2 Two-Way Radio User Manual 1
Northfield Telecommunications, Inc. d/b/a Advanced Wireless Communications Two-Way Radio 1
user manual
HD-1000V2 GENERAL/概述 INTRODUCTION SCOPE OF THIS MANUAL 引言 本手册的范围 This manual is intended for use by experienced technicians familiar with similar types of commercial grade communications equipment. It contains all required service information for the equipment and is current as of the publication date.Changes which may occur after publication are covered by either Service Bulletins or Manual Revisions. These are issued as required. 本手册是提供给熟悉通信专业并且具有维修经验的技术人员 使用的。 它包括了维修该设备所 需要的全部资料和现行公布 的数据。在出版后可能发生变动,如果需要,可以使用《维修 通报》或《手册修订本》进行补充。 ORDERING REPLACEMENT PARTS 替换零件的订购 When ordering replacement parts or equipment information, the full part identification number should be included.This applies to all parts: components, kits, or chassis. If the part number is not known, include the chassis or kit number of which it is a part, and a sufficient description of the required component for proper identification. 当订购替换零件或设备信息时,应注明完整的零件识别号码。 所有的零件均有识别号码:元件、组件或机壳。如果不知道 零件的号码,为了正确地识别,必须注明此元件所属的机壳 或组件的号码,并对元件进行充分的说明。 PERSONAL SAFETY 个人安全 为了个人的安全,请注意下列事项: The following precautions are recommended for personal safety: • DO NOT transmit until all RF connectors are verified secure and any open connectors are properly terminated. • SHUT OFF and DO NOT operate this equipment near electrical blasting caps or in an explosive •This equipment should be serviced by a qualified technician only. • 在没有认真核实所有射频插头之前或有任何一个打开的插头 没有连接到响应端子上的情况下,均不要发射。 • 在电爆管附近或在易燃性气体环境中,必须关掉电源,不要 操作本设备 • 本设备只应该由有资格的技术人员来维修。 SERVICE 维修服务 This radio is designed for easy servicing. Refer to the schematic diagrams, printed circuit board views, and alignment procedures contained within. 为了便于维修本设备,建立了完整的维修服务体系,提供了 包括原理图、印刷线路图和调整步骤在内的资料供参考。 Number of channels RF Power Output 199 0.5W/1W 信道数量 199 射频输出功率 0.5W/1W SAFETYTRAINING INFORMATION Your radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”. In addition, your radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave. The following accessories are authorized for use with this product. Use of accessories other than those (listed in the instruction) specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure. To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines: DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. DO NOT transmits for more than 50% of total radio use time (“50%duty cycle”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch. ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the belt-clip which is listed in instructions when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver SAVE THIS INSTRUCTION MANUAL- This instruction manual contains important operating instructions for the Two-Way Radio EXPLICIT DEFINITIONS WORD DEFINITION WARNING Personal injury, fire hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. OPERATING NOTES When transmitting with a portable radio, hold the radio in a vertical position with its microphone 5 to 10 cm (2 to 4 inches) away from your mouth. Keep the antenna at least 2.5 cm (1 inch) from your head and body. If you wear a portable two-way radio on your body, ensure that the antenna is at least 2.5 centimeters (1 inch) from your body when transmitting. PRECAUTIONS WARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical. WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. CAUTION! NEVER short the terminals of the battery pack. NEVER connect the transceiver to a power source other than the Battery listed below Such a connection will ruin the transceiver. DO NOT push the PTT when not actually desiring to transmit. AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below –30°C (–22°F) or above +60°C (+140°F). DO NOT modify the transceiver for any reason. MAKE SURE the flexible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the transceiver. BE CAREFUL! The series transceivers employ waterproof construction, which corresponds to IPX7 of the international standard IEC 60529 (2001), 1 m depth for 30 minutes. However, once the transceiver has been dropped, waterproofing cannot be guaranteed due to the fact that the transceiver may be cracked, or the waterproof seal damaged, etc. The use of non-Advanced battery packs/chargers may impair transceiver performance and invalidate the warranty. FCC CAUTION: Changes or modifications to this device, not expressly approved by Manufacturer, could void your authority to operate this transceiver under FCC regulations. 910 MODES 模式 USER MODE MODES PC MODE PC模式 用户模式 FUNCTION 模式类型 User mode For normal use. 用户模式 用于普通操作 PC mode Used for communication between the radio and a PC 计算机模式 Used for communication between the radio and a PC 功能 How to enter each mode PROCEDURE MODES User mode PC mode Power ON 模式类型 用户模式 操作步骤 打开电源开关 Receiver commands from PC 计算机模式 从计算机接收命令 PC MODE 计算机模式 Preface 前言 The HD-1000 transceiver can be programmed using a personal computer, A programming interface cable and programming software. The programming software can be used on an IBM PC or compatible. Fig-1 shows the setup of a PC for programming. 通过个人电脑,使用编程电缆和编程软件,对对讲机HD-1000 进行编程设置。图1表示一台IBM计算机的编程设置过程。 Caution: When removing or installing the programming cable,first switch off the radio power. Additionally, be sure to disable the VOX function, if 注意 当拔除或者插入编程电缆首先关闭对讲机电源。另外,确保声 控功能已关闭,如果声控被激活,可能有时会开启连接噪音。 it’s enabled, as it can sometimes activate from connection noise. Connection procedure 1. Connect the HD-1000 to the personal Computer using the interface cable. 连接步骤 1.使用接口电缆将HD-1000与个人电脑连接。 2.当电源开关打开,可以进入用户模式。 2. When the POWER is switched ON, you can enter user mode. Programming software description 编程软件说明 The software allows a user to program the HD-1000 radios via the programming interface cable. 该软件允许用户经由编程接口电缆对HD-1000进行编程设定。 • Programming with IBM PC If data is transferred to the transceiver from a PC with the software, the destination data (basic radio information) for each set can be modified. 使用IBM计算机编程 如果从使用软件的IBM计算机将数据发送到手持机,设定的目的 数据(基本通信参数)均可被修改。 DISASSEMBLY FOR REPAIR/维修时拆卸部分 Separating the case assembly from the chassis 1. Remove the knob 1 and the round nut 2 2. Remove the six screws 3 and 4 3. Expand the right and left sides of the bottom of the case assembly, lift the chassis,and remove it from the case assembly 5. 4. Taking care not to cut the speaker lead 7,open the chassis and case assembly. Separating the chassis from the unit Remove the screws 8 and drop-out line, and lift the first unit off. 从底座上分离外壳 1.取下旋扭 1 和环形螺母 2 2.取下六颗螺钉 3 和 4 3.掀开外壳底部的左右两侧,取下底座,并外壳中取出 5 4.小心不要折断扬声器引线 7 ,拆下底座和外壳。 底座从主板上分离 取下螺钉 8 ,然后取下主板. FCC ID: Q9SHD-1000V2 IC: 4651A-HD1000V2 NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-702 Create Date : 2009:05:19 14:13:18+08:00 Metadata Date : 2010:10:18 16:36:19+08:00 Creator Tool : Adobe Illustrator CS2 Format : application/pdf Title : 1 Creator : USER Document ID : uuid:4864606d-f705-4c48-bcd4-2149881a7dc5 Instance ID : uuid:bcf69f16-a03b-4473-8493-8bbfdc9381d7 Producer : Adobe Photoshop for Windows Has XFA : No Page Count : 10 Application Record Version : 2 By-line : USER Object Name : 1 X Resolution : 72 Y Resolution : 72 Orientation : Horizontal (normal) Resolution Unit : inches Software : Adobe Photoshop CS Windows Modify Date : 2007:12:06 19:01:55 Artist : USER Color Space : Uncalibrated Exif Image Width : 516 Exif Image Height : 776 Compression : JPEG (old-style) Thumbnail Offset : 318 Thumbnail Length : 0 For : User, - Bounding Box : -31 -33 499 761 Warning : IFD0 pointer references previous IFD0 directory IPTC Digest : 4cae19fc467be10a63fa352107fd34d8 Displayed Units X : inches Displayed Units Y : inches Print Style : Centered Print Position : 0 0 Print Scale : 1 Global Angle : 30 Global Altitude : 30 Copyright Flag : False URL List : Slices Group Name : 4 Num Slices : 1 Pixel Aspect Ratio : 1 Photoshop Thumbnail : (Binary data 4571 bytes, use -b option to extract) Has Real Merged Data : Yes Writer Name : Adobe Photoshop Reader Name : Adobe Photoshop CS Exif Byte Order : Big-endian (Motorola, MM) Creator Version : 12 Container Version : 9 Author : USEREXIF Metadata provided by EXIF.tools