OPISYS orporated USHR-781921-5B 4G 5-Band Repeater Model Name-USHR-781921-5B User Manual revised
OPISYS Incorporated 4G 5-Band Repeater Model Name-USHR-781921-5B revised
User manual revised
Model : USHR-781921-5B Five-band Signal Booster For In-building User Guide Installation Manual 1. Introduction 2. Kit Information 3. Installation 4. Troubleshooting 5. Specifications 6. Certificates 7. Contact Info. Model: USHR-781921-5B Leading Edge Technology Signal Booster USHR-781921-5B signal booster designed to boosts cellular signal for area prone to weak coverage area. Its coverage is on 800 MHz, 1900MHz, AWS and 4G Verizon and AT&T 700 MHz as well as 4G Sprint. To allow installer to optimize signal and gain control each frequency band, it has control knobs. -2- Five-band Signal Booster For In-building Contents 1.1. Precautions This is a CONSUMER device. This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. Reference : Direction/Information for the proper operation Cautions : Information for users to avoid malfunctions Warning : Instruction for users to avoid unexpected hazard 1.1.1 Do not drop the device - It may damage the product and its function 1.1.2 Do not place near magnetic material - It may cause possible malfunction 1.1.3 Product is recommended to be used with included AC/DC adapter - It may cause possible malfunction 1.1.4 Install the product where it is recommended - It may not properly operate if it is not recommended location 1.1.5 Do not disassemble/ repair the product - Warranty may void once you disassemble the product. 1.1.6 Turn off the device immediately if a smoke or any strange odor is detected from the product. 1.1.7 Use included bolts to install on the wall. Make sure it is safely installed before operation 1.1.8 Outside Antenna must be installed no longer than 32 feet(10 meter) above ground 1.1.9 This signal boosters are designed to be operated in a designated area in a building. -3- Five-band Signal Booster For In-building 1. INSTRODUCTION 1.2.1. Summary This signal booster can be installed on residential area, office, warehouse etc. . Following is advantages of using Five-band signal booster. I. Decrease dropped call rate II. Increase signal strength III. Improve Data / Voice quality IV. Prolong hand phone battery life V. Improve data Communication Rate This Signal booster solves coverage problems and improves connection quality in the building. In addition, this covers LTE of Band 12, Band 13, Cellular Band 5, AWS Band 4 and PCS Band 25 for mobile phone users. (Please see page 20 for operating frequency in details) 1.2.2. Features I. Wider Coverage area - Band 12 Gain DL 60dB / UL 60dB - Band 13 Gain DL 60dB / UL 61dB - Band 5 Gain DL 62dB / UL 61dB - Band 4 Gain DL 70dB / UL 68dB - Band 25 Gain DL 69dB / UL 68dB II. ALC(Automatic output Level Control) - Stabilize operation in any radio environment III. Fulfill revised FCC rule at +23dBm output power - Provide high data communication rate IV. Easy gain control by dip switch located on the front side of product V. Support five band - Enable to connect service from multiple carrier simultaneously - Band 12/13/5/4/25 service simultaneously - Band 12/13/5/4/25 adopt independent operation algorithm -4- Five-band Signal Booster For In-building 1.2 . Summary & Features VII. Allow to manage and control product by GUI(Graphic User Interface) - Please ask professional installer about GUI Program VIII. Enable to stay connected in homes and offices - Please ask professional installer for installation on homes & offices IX. Device status with LED light(see page 17) X. Automatic isolation detection and gain setting - If the device is shut down, turn on again after turning off the AC power. XI. Uplink sleep mode - If no signal has been detected for 5 minutes, Uplink path will be shut down. XII. UL/DL gain interlocking mode -5- Five-band Signal Booster For In-building VI. Check status of booster by LED indicator I. Automatic Shut Down Mode Built-In Automatic Self-Monitoring Features for Anti-Oscillation: Automatic shut down mode operates when oscillation in the uplink and downlinks bands are detected and terminates potential harmful interference to wireless networks. • 1 minute non-operative mode on the first initial oscillation detection. • Default algorithm re-set mode as Auto S/D Mode is cleared • Complete shut off mode on the 5th repetition of auto shutdown mode status. All path are independently monitored and operated. II. Intermodulation Gain & Power Limit Control Uplink & downlink path formulates consistent link balance to regulate its input and output gain & power limits. Max UL gain < - 34dB – RSSI + MSCL (“ FCC 13-21,(i), 78p”) RSSI : Downlink composite received signal power at the donor port ( calculation value : DL Output – DL Gain ) MSCL : Mobile station and repeater service port minimum coupling Loss ( setting value ) All path gain limits are independently controlled III. ALC (Automatic Level Control) & AGC ALC is implemented to keep regular output power level for abnormal high input signal level. The regular output power makes possible high quality of phone call and data transfer. AGC is designed to automatically control gain. • Optimal Window Size (frequency range) sets the optimal level to increase faster response to modulated signal level changes on the basis of gain power control via signal input/output differential calculation all path gain limits are independently controlled IV. UL Path Automatic Sleep Mode If coverage is non-existent (Zero Area Zone), Uplink path shuts off as a harmful interference avoidance protocol and minimizes its power consumption. -6- Five-band Signal Booster For In-building 1.3 Functions • Automatic Turn Off / if UL PATH < -90dBm • Automatic Turn On / if UL PATH > -88dBm **All path gain limits are independently controlled V. Oscillation Auto Prevention • Degradation Protection: Detects potential performance degradation due to the overload signal feedback (over-heating) signals by isolation check & gain configuration. • Feedback Limits: Sets the operating range to exceeding high level signals from donor antenna (outside antenna) of a signal booster to service antenna (inside antenna) Booster Gain < Antenna to Antenna Isolation – 15dB If optimal isolation gain is not attained, Relevant path shuts off automatically. **All bands are independently controlled -7- Five-band Signal Booster For In-building IV. UL Path Automatic Sleep Mode (continue ) Five-band Signal Booster For In-building 2. Kit Information ② AC/DC Adapter ① USHR-781921-5B ④ Installation bolts ③ User Guide ① USHR-781921-5B : 5 Band BTS and mobile phone signal booster ② AC/DC Adaptor : 110VAC power supply ③ User Guide : Operation & Installation manual ④ Installation Bolts : Holds signal booster on the vertical wall ● List of approved antennas & cables Antenna Item Service Antenna (Indoor Antenna) RF Cable Model Gain Model Cable type TS260771 +8dBi AC200000 LMR200 TS250374 +5dBi TS320000 RF240 +2dBi TS340000 RF400 TS210471 +4.5dBi TS350000 ½” TS220971 +9dBi TS360000 ½” TDI-690/2500-SJ +7dBi TQI-700/2700-SJ-01 Donor Antenna (Outdoor Antenna) -8- 3.1 Installation Diagram Out Door Antenna Indoor Antenna USHR-781921-5B Base satation 3.1.1. Install outdoor antenna on higher location to avoid any signal interference. Mount towards to the BTS where a clear line-of-sight path exists for optimal signal level. 3.1.2. Install indoor antenna at appropriate location such as wall or roof ceiling. Make sure service antenna is not blocked by furniture or appliances. 3.1.3. Use enclosed bolt to fix a booster on the wall and plug in power adaptor. 3.1.4. For best optimal operation, antenna isolation (oscillation level) should be set above minimum 15 dB gain. The industry standard for antenna to antenna isolation formula is BDA gain + 15 dB. -9- Five-band Signal Booster For In-building 3. Installation Cable Item Model Q’ty Instruction Outdoor Antenna TS220971 Install toward to cell tower Waterproof connectors connection Indoor Antenna TS260771 Install indoor antenna opposite direction to outdoor antenna Signal Booster USHR-781921-5B Install on hard wall with bracket and screws Outdoor Cable TS350000 Fasten connection between antenna and cable connector Indoor Cable TS320000 Fasten connection between antenna and cable connector AC/DC Adaptor SAMA-02-600 Use only provided adaptor - 10 - Five-band Signal Booster For In-building 3.2 One Outdoor Antenna & One Indoor Antenna Installation Cable Item Model Q’ty Instruction Install toward to cell tower Waterproof connectors connection Outdoor Antenna TS220971 Indoor Antenna TQI-700/2700-SJ-01 N-way Splitter Option Divide two antennas and fasten connection between antenna and splitter Signal Booster USHR-781921-5B Install on hard wall with bracket and screws Outdoor Cable TS360000 Fasten connection between antenna and cable connector Indoor Cable TS340000 3(N+1) Fasten connection between antenna and cable connector AC/DC Adaptor SAWA-02-600 2(N) - 11 - Install indoor antenna opposite direction to outdoor antenna Use only provided adaptor Five-band Signal Booster For In-building 3.3 One Outdoor Antenna & Two and More Indoor Antenna Installation 3.4.1 Outdoor Antenna Installation the antenna for the device must be installed to comply with the 10 meter above ground maximum antenna height limitation . a) Choose a location to installation where minimum heat and good ventilation area. b) Install outdoor antenna toward Cell Tower on the roof of building or high area where signal reception is optimized. c) If you don’t know where a cell tower is, install the system and find strongest direction with your cellular phone signal and then adjust outdoor antenna. d) Run the cable to signal booster and connect to outdoor antenna. e) Run the cable to indoor antenna to signal booster and choose a location for indoor antenna. f) Use the bracket to attach to a firm wall. A minimum distance from indoor to outdoor antenna must be at least 20 vertical feet and 50 horizontal feet each other. g) Turn on power as all connections are tightly finished. h) As the green light are on, you will get better signal. - 12 - Five-band Signal Booster For In-building 3.4 Installation Details Five-band Signal Booster For In-building 3.4.2 Booster Installation Item Q’ty Instruction Indoor ANT Port N-Type Indoor antenna connector Outdoor ANT Port N-Type Outdoor antenna connector Bracket 4 Hole Use for wall mount with 4 screws Adaptor for DC connection Plug in after all connection is finished Tri-color See page 17 GUI Port Graphic user interface(Professional use only) Debug Port Professional use only Adaptor DC IN LED - 13 - Five-band Signal Booster For In-building ① This booster designed to automatic installation function and you may only follow instruction manual. ② Dip switch control refers the following table. In order to use dip switch, the dip switch control function must be enabled by useing GUI in advance. The default setting of dip switch is OFF. ③ Dip switch must be managed and operated by professional an installer only. Please ask professional installers, distributors and dealers to adjust dip switch. Attenuation State SW1 SW2 SW4 SW8 SW16 1 dB ↑ ↓ ↓ ↓ ↓ 2 dB ↓ ↑ ↓ ↓ ↓ 4 dB ↓ ↓ ↑ ↓ ↓ 8 dB ↓ ↓ ↓ ↑ ↓ 16 dB ↓ ↓ ↓ ↓ ↑ ※ Switch setting is cumulative. This means the total amount of attenuation. - 14 - 3.4.3.1. Connect donor antenna cable to outdoor antenna port as shown below. 3.4.3.2. Connect Service antenna to indoor antenna port as shown below. 3.4.3.3. Plug in power adaptor to power outlet. - 15 - Five-band Signal Booster For In-building 3.4.3 Booster and Antenna connection 3.4.3.5. The factory default set-up has both Automatic Attenuator Control & Automatic Level Control (ALC) pre-activated by USHR-781921-5B Internal CPU. All Isolation Check features can be manually adjusted via dip switch using GUI program (Booster Control & Monitoring Software). - 16 - Five-band Signal Booster For In-building 3.4.3.4. Plug in AD/DC adaptor to connector listed as DC12V Item GREEN LED RED LED Reference ON × See 4.1.1 OFF × See 4.1.1 ON See 4.1.2 ON See 4.1.3 Green Blinking per 1 sec cycle See 4.1.4 Green Blinking per 5 sec cycle See 4.1.5 RED Blinking per 1 sec cycle See 4.1.6 RED Blinking per 5 sec cycle See 4.1.7 PWR ALL Band 4.1.1. Power on /off status. 4.1.2. Normal operation condition. 4.1.3. Booster detects excessive input signal and shut down. 4.1.4 Shutdown Algorithm status on High input Signal. 4.1.5. Path OFF indicator during Uplink Sleep Mode. 4.1.6. Isolation Shutdown Algorithm status 4.1.7. Booster detects Insufficient Isolation between donor & service antenna and shut down. - 17 - Five-band Signal Booster For In-building 4. Trouble Shooting 5.1. Electrical Specifications Item Frequency Range Modulation Type Input Power limit Specifications Note Up Link 698 ~ 716 MHz BAND12 Down Link 728 MHz ~ 757MHz BAND12 / BAND13 BAND 13 Up Link 776 ~ 787 MHz Down Link 869~894 MHz Up Link 824 ~849 MHz Down Link 2,110 ~ 2,155 MHz Up Link 1,710 ~ 1,755 MHz Down Link 1,930 ~ 1,995 MHz Up Link 1,850 ~ 1,915 MHz BAND 5 BAND 4 BAND 25 GSM. EDGE, CDMA, EVDO, HSPA, LTE Down Link -40dBm max Up Link -10dBm max Down Link -40dBm max Up Link -10dBm max Down Link -40dBm max Up Link -10dBm max Down Link -40dBm max Up Link -17dBm max Down Link -40dBm max Up Link -17dBm max Down Link +2dBm@ booster output port ALL DL Channel Up Link +23dBm@ booster output port ALL UL Channel Up Link 30dB ~ 60dB (±1.0dB) BAND 12 Down Link 42dB ~ 60dB (±1.0dB) BAND 12 / BAND 13 Up Link 31dB ~ 61dB (±1.0dB) BAND 13 Down Link 42dB ~ 62dB (±1.0dB) Up Link 31dB ~ 61dB (±1.0dB) Down Link 42dB ~ 70dB (±1.0dB) Up Link 38dB ~ 68dB (±1.0dB) BAND12 BAND13 BAND 5 BAND 4 BAND 25 Output Power Gain(RSSI) Gain(ALC)` BAND 5 BAND 4 Down Link 42dB ~ 69dB (±1.0dB) Up Link 38dB ~ 68dB (±1.0dB) Up Link 33dB ~ 60dB (±1.0dB) BAND 12 Down Link 42dB ~ 60dB (±1.0dB) BAND 12 / BAND 13 Up Link 33dB ~ 61dB (±1.0dB) BAND 13 Down Link Up Link Down Link Up Link Down Link Up Link 42dB 33dB 42dB 40dB 42dB 40dB - 18 - 62dB 61dB 70dB 68dB 69dB 68dB (±1.0dB) (±1.0dB) (±1.0dB) (±1.0dB) (±1.0dB) (±1.0dB) BAND 25 BAND 5 BAND 4 BAND 25 Five-band Signal Booster For In-building 5. Specifications Ripple Noise Figure Noise Power Limit Specifications NOTE Down / Up Link Down / Up Link <8dB / < 8dB(Peak to Peak) < 8.0dB / < 8.0dB ALL BAND Max Gain Down Link < -70dBm/MHz On shutdown Up Link < -70dBm/MHz On shutdown & sleep mo de Down / Up Link FCC ALL BAND FCC ALL BAND Down / Up Link Propagation Delay < 3us Input VSWR ≤ 2.0 : 1 ALC Setting Level Down Link(Upper Value) +2dBm±1.0dB Window Size(Lower Offset) 1 ~ 10dB(Default : 2dB) Up Link (Upper Value) +23dBm±1.0dB Window Size(Lower Offset) 1 ~ 10dB(Default : 2dB) ALC Range Down / Up Link DL ≤ 18dB UL ≤ 27dB Band 12 Down / Up Link DL ≤ 18dB UL ≤ 28dB BAND 13 Down / Up Link DL ≤ 20dB UL ≤ 28dB BAND 5 Down / Up Link DL ≤ 28dB UL ≤ 28dB BAND 4 Down / Up Link DL ≤ 27dB UL ≤ 28dB BAND 25 Down Link ≥-40dBm/Total±1.0dB ALL Down Link Up Link ≥-10dBm/Total±1.0dB Band12, Band13, Band 5 Up Link ≥-17dBm/Total±1.0dB Band 4, Band 25 Down Link DL detects OSC under 1 sec. Up Link UL detects OSC under 0.3 sec. Up link On@ > -88dBm, OFF@ < -90dBm Shutdown Level OSC Level Uplink In-activity Gain Control Range Down link 0dB ~ 30dB / 1dB Step Up link 0dB ~ 30dB / 1dB Step Dip Swit ch Gain Control Deviation No uplink signal for 5 minutes Be controlled GUI or Dip Switch Total Atten Control Range : 0dB ~ 30dB / 1dB Step < ± 1dB EVM < 7% No Feedback 30dB ~ 75dB / BAND12 31dB ~ 76dB / BAND13 Isolation checking Range 31dB ~ 76dB / BAND 5 38dB ~ 83dB / BAND 4 Detecting deviation: < ±2 .0dB 38dB ~ 83dB / BAND 25 Out Band Spurious 3rd IMD Level < -13dBm/1kHz RBW 9kHz ~ 150kHz < -13dBm/10kHz RBW 150kHz ~ 30MHz < -13dBm/100kHz RBW 30MHz ~ 1GHz < -13dBm/1MHz RBW 1GHz ~ 12.75GHz < -19dBm Max Output Level Frequency Stability ≤ ±0.01ppm - 19 - Five-band Signal Booster For In-building Item Specifications GUI Interface RS-232C ▪ Normal: Green ▪ Power turn off: Off PWR Alarm & Status NOTE Normal: Green Over Power Shutdown: RED Checking SD: Green Blinking per 1 sec cycle Checking OSC Algorithm: Red Blinking per 1 sec cycle ▪ Sleep Mode: Green Blinking per 5 sec cycle ▪ Isolation SD : RED Blinking per 5 sec cycle ▪ ▪ ▪ ▪ Display Alarm Power Consumption < 50W Operating Power AC/DC Adapter (AC110V or AC220V) RF Connector N-type Female ● Additional Information: This booster is a bi-directional amplifier for the boosting of cellular phone signals and data communication devices. The following frequency bands and emission types are utilized. Frequency Band Band DL UL Band 12 & Band 13 728 ~ 757 MHz Band 5 869 ~ 894 MHz 824 ~ 849 MHz Band 4 2110 ~ 2155 MHz 1710 ~ 1755 MHz Band 25 1930 ~ 1995 MHz 1850 ~ 1915 MHz 698 ~ 716 MHz 776 ~ 787 MHz Emission Designators CDMA HSPA LTE EVDO EDGE GSM F9W F9W G7D F9W G7W GXW - 20 - Five-band Signal Booster For In-building ITEM Item Specifications Note Dimensions (L × W × H) 231mm x 288mm x 71mm Except Bracket and Connector (Tolerance ±5mm) Weight < 6.8Kg 5.3. Environment Specification Item Specifications Temperature -30 ~ 55℃ (-22 ~ 131℉) Humidity 10 ~ 95% Note 5.4. AC/DC Adaptor Specification Items Specifications AC input power 90VAC ~ 264VAC, 47Hz ~ 63Hz Output Voltage +12.0 VDC Current Range 6.0A ~ 0.0 A Operation Temperature -30℃ ~ +55℃ Operation humidity 10% ~ 90% 6. Certificates - 21 - Note Five-band Signal Booster For In-building 5.2. Mechanical Specification Five-band Signal Booster For In-building 7. Contact Information 7.1 Location 7.2 Contact Address : 511 s. HARBOR BLVD STEP. LAHABRA, CA 90631 Mon.-Fri. Hours : 9 a.m. to 5 p.m. TEL : 562-448-3102 FAX : 562-448-3105 - 22 - Five-band Signal Booster For In-building Memo - 23 -
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : 아이솔 Create Date : 2015:02:27 13:19:18+09:00 Modify Date : 2015:02:27 13:19:43+09:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2015:02:27 13:19:43+09:00 Creator Tool : PowerPoint용 Acrobat PDFMaker 10.1 Document ID : uuid:089b35d4-4899-4e76-bb2b-866fe2075654 Instance ID : uuid:dd310648-3372-4581-868e-47169240dd53 Format : application/pdf Title : EZ CELL 사용설명서 (MODEL : AEHR-2009) Creator : 아이솔 Producer : Adobe PDF Library 10.0 Company : 중계기팀 Page Layout : SinglePage Page Count : 23EXIF Metadata provided by EXIF.tools