The Ketchum Group Outdoor Technology OT2800 BT SPEAKER User Manual
The Ketchum Group, Inc. dba Outdoor Technology BT SPEAKER
User Manual
TURTLE SHELL 3.0 ® Hi. Good call on picking up the Outdoor Tech Turtle Shell 3.0 wireless boom box. Your experience of the universe will soon be enhanced wirelessly and powerfully. This manual exists to help make sure that you use it correctly, so you’re definitely going to want to relax for a hot second and look through this. ® Kisses, ® ANATOMY Power On / Power Off Multi Function Button Skip Backward / Volume Down Skip Forward / Volume Up Micro USB Charge Port / 3.5 mm Aux Port USB Output Charge Port Microphone Light Indicator POWER UP TO CHARGE For best results, fully charge your Turtle Shell® 3.0 before use! 1. Connect the included MIcro USB cord to a power source and the charging port on the Turtle Shell® 3.0. When charging, the red LED light will stay activated. ***Full charge time is about 4-5 hours. 2. When the Turtle Shell® 3.0 is fully charged, the RED light will turn off. The displayed battery meter is supported for Apple products. *The Turtle Shell® 3.0’s Bluetooth and music functions can still operate while charging. MUSIC FUNCTIONS Music / Device Controls Skip backward Volume down FUNCTION MFB BUTTON Skip forward Volume up ACTION Power on Press 3 sec Power off Press 2 sec Pairing mode Hold 3 sec Manual pairing mode Hold for 3 sec Play / Pause Short press once Volume up Short press once Volume down Short press once Skip forward Press & hold for 2 sec Skip backward Press & hold for 2 sec PHONE FUNCTIONS Device Controls Skip backward Volume down FUNCTION MFB BUTTON Skip forward Volume up ACTION Answer an incoming call Short press once Reject an incoming call Press & hold for 2 sec End call Short press once Siri/Voice activation Press & hold for 2 sec & release PAIRING TO DEVICE Power On / Off ON: Hold the Power Button for 2-3 seconds or until the LED light flashes blue and the voice prompt states “Power on” OFF: Hold the Power Button for 3-4 seconds or until the LED light flashes red and the voice prompt states “Power off” Enter Pairing Mode When powered on hold the “+” and “-” at the simultaneously for 2-3 seconds or until you see the LED light flash blue 3 times and the voice prompt states “Pairing.” Pairing Turtle Shell 3.0 to Device Open the Bluetooth settings on your device. If you have put your Turtle Shell® 3.0 into pairing mode, it should be listed as “ODT Turtle Shell® 3.0” as an available device to pair. Connect with the Turtle Shell® 3.0 and enter “0000” if prompted. The voice prompt will state “Successful” if the Turtle Shell 3.0 and your device connect. SPEAKER TO SPEAKER PAIRING TS3 #1 TS3 #2 STEP ONE Turn on TS3 #1 and wait till the voice prompt states that the speaker is on. Then press & hold simultaneously the MFB button and the “+” button. TS3 #1 will then state that it is in pairing mode. STEP TWO Turn on TS3 #2 and wait till the voice prompt states that the speaker is on. Then press & hold simultaneously the MFB button and the “-” button. TS3 #2 will then state that it is in pairing mode. STEP THREE Once TS3 #1 and TS3#2 are connected, the voice prompt will state “Successful.” For more functions, go to outdoortech.com/apps/ to download the Outdoor Tech app. LISTEN CONTINUED The built-in microphone means that the Turtle Shell 3.0 can be used as a wireless headset. *NOTE: The built-in microphone only works when connected via Bluetooth. The following are tips on how to use your Turtle Shell 3.0 to speak on the telephone: Answer a call......... Press the multifunction button. End a call............... Press the multifunction button. Decline a call......... Press and hold the multifuntion button for two seconds. Make a call............ Use your phone to dial as usual. Listen and talk through the Turtle Shell® 3.0. Mute...................... Hold the >> and << buttons for 2 seconds, or until you hear a beep. FAQ Hearing Distortion A. Lower the volume on your Turtle Shell 3.0 and / or phone /device. B. Make sure it’s charged up. Check for low battery, then charge if necessary. Not Loud Enough A. Turn up the volume on your phone / device or your Turtle Shell 3.0. B. Make sure it’s charged up. C. Plug the Turtle Shell in to your phone / device via 3.5mm stereo cable. Unable to Pair A. Confirm your phone / device is Blue tooth compatible. B. Re-Pair: Follow pairing instructions in this guide. Signal Loss or Dropouts via Bluetooth A. Move Turtle Shell closer to your phone / device. B. Make sure it’s charged up. C. Turn off your Turtle Shell 3.0 and phone / device, then power up and reconnect. ® ® ® ® SPECS Rating: IPX7 Bluetooth v 4.2 Bluetooth Profiles: HSP, HFP. A2DP, AVRCP Capatability: Bluetooth v 1.1 and above Operating range: 32 ft Operating range between speakers: 15 ft Device name: ODT TURTLE SHELL 3.0 Power source: Lithium ion rechargeable battery cell Battery capacity: 3600mAh / 13.32 Wh Charge Output: 5V / 1A Charge Input: 5V / 2.1A Playing Time: Up to 20 hrs Charge Time: ~4.5 hrs Operating Temperature: 0~45° C Storage Temperature: -20~60° C RoHS: Fully RoHS compliant K, bye. DON’T BE SO ANTISOCIAL Facebook.com/outdoortech Twitter & Instagram: @outdoortech Questions, comments, complaints, secret desires, or just to say what’s up: email info@outdoortech.com K bye. outdoortech.com FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement: This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Canada Statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisee aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'evaluation dans la section 2.5 de RSS 102 et la conformite a l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformite de rf. 10 Important Safety instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Only use attachments/accessories specified by the manufacturer. 10. Unplug this apparatus during lightning storms or when unused for long periods of time. 11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 12. The apparatus shall be used at maximum 45°C ambient temperature. 13. The maximum height above sea level is 2000m 14. The use of apparatus in moderate climates and indoor only 15. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, tablecloths, curtains, etc. 16. No naked flame sources, such as lighted candles, should be placed on the apparatus. 17. Use only power supplies provided by KICKER 18. Battery pack shall not be exposed to excessive heat such as sunshine, fire or the like. CAUTION Danger of explosion if battery is incorrectly replaced, Replace only with the same or equivalent type. Symbol The appliance shall not be disposed together with the normal waste. It must be recycled. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. érature ambiante. é au maximum de 45 °C la temp tempé utilisé l'appareil doit être utilis 13. la hauteur maximale au - dessus du niveau de la mer est de 2 000 14. 15. 16. 17. 18. utiliser uniquement des fournitures fournies par le pouvoir
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Tagged PDF : No XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2016:07:05 14:00:01-07:00 Metadata Date : 2016:07:07 09:20:08+08:00 Modify Date : 2016:07:07 09:20:08+08:00 Creator Tool : Adobe InDesign CC 2015 (Windows) Instance ID : uuid:a68ad57e-140f-4cc8-b1ea-50ea0bb8e03d Original Document ID : xmp.did:DEB6D13D809CE21197E2DF22494C819B Document ID : xmp.id:561507ce-3dca-334f-82ca-2ecbd3f0b3a6 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:99675e13-b212-994b-a537-b9382b4fa597 Derived From Document ID : xmp.did:7eaf620f-54a9-4542-9797-51483d2e74f5 Derived From Original Document ID: xmp.did:DEB6D13D809CE21197E2DF22494C819B Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2015 (Windows) History Changed : / History When : 2016:07:05 14:00:01-07:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Has XFA : No Page Count : 17 Language : en-US Creator : Adobe InDesign CC 2015 (Windows)EXIF Metadata provided by EXIF.tools