3M Cogent ACD100P-CG Mini-Gate User Manual Mini Gate ACD100P CG
3M Cogent, Inc. Mini-Gate Mini Gate ACD100P CG
Mini-Gate User Manual-ACD100P-CG 12.28
Device Installation Guide Option 2 : The cassette (86x86) on wall Option 1 : On wall directly Step 1 Mini-Gate User Manual Address : 10/F,Tinwe Industrial Park Phase 2, Liufang Road No.6, Area No.67, Baoan District, ShenZhen Tel :+ 86 - 755 - 86013579 Step 1 Step 3 Step 2 Step 2 Step 3 Step 4 Step 1: Cassette(86*86) Step 2: Screw fixing board to cassette, choose the right size of screws by different cassettes. Step 3: Cover the fixing board. Step 4: Screw stainless steel plate to fixing board, then install device on the stainless steel plate. Step 1: Screw stainless steel plate according to the 4 holes marked on the drawing,choose right size of screws by different walls Step 2: Insert installing device aimed to stainless steel plate. Step 3: Fasten this screw on the bottom. Fax:+ 86 - 755 - 86013575 Introduction for Function and Technical Data l Model:ACD100P-CG l Processor:SAM9G45@400MHz, Processor List Quantity Mini-Gate biometric access control Fixing board A (plastic) l Memory:128 MB DDR/ 128MB Flash l Expansion Memory:Micro SD(2GB for default configuration) l LCD Display:1.8" TFT Color LCD LCD LED Contactless Card Area (Keypad Part is for RF Card Reading Area) Key Pad Fixing board B (plastic) 1 3 4 8 9 14 15 20 l Keypad:3 X 5 keypad Type Relay Screw (PM4X5) 4+2 Screw(PWM3X5) Screw(FM 2X6) Wiegand USB Port Reset Botton Speaker Fingerprint Sensor Power Adapter(DC 12V/1.5A) RJ45 Network Port Connector DC12V Power Connector RS485 Power Ethernet L spanner Mini-Gate User Manual l LED Indicator: Multi-color × 3 No 10 11 12 13 14 17 18 19 20 21 22 23 24 25 26 27 Name Relay 12V+ RelayGND(Relay GND) Wiegand_In_D1/LED_Input Wiegand_In_D0 GND(Wiegand GND) Wiegand_Out_D1 Wiegand_Out_D0 P_GND(Safety GND) GND(RS485 GND) RS485+ RS485GND(Power GND) Power_In(12V) RXRX+ TXTX+ Color Yellow Orange Black Brown Purple Black White Green Yellow&Green Black Blue Gray Black Red Blue Green White Yellow UART For GPRS Module 7 PIN_Female _Connector l Audio:Beep l PC Port:USB2.0 l Built-in Relay Control: 1 l Power supply:12V DC/1.5A l Current:450mA @ 12V l Operating Temperature:0 ~ 45˚ C l Storage Temperature:0 ~ 45˚ C l Fingerprint Sensor:Cogent CSD100, 500dpi Optical Sensor, (FBI Certified) l Matching Speed:1:1 ≤1.2s,1:N ≤2s (N≤5000) l FRR:1% l FAR:0.001% l Matching Security Grade:Lower, Middle, High (Configurable) l Acceptable Fingerprint Rotation:+/-15 degree (Default) Module and Function Guide Standard Mode Advanced Mode Add Administrator Time Setting OK OK Delete Administrator Administrator Setting and User Setting OK OK Add User OK Note: Factory Default: Administrator user ID:"1"; Pin #:"1". This will be invalid after new admin setup. "User setting" should be changed to "admin setting" Delete User Lightness Setting OK OK Fingerprint Mode OK For fingerprint identify, select this mode. Fingerprint + Card Mode Mode Setting OK 模式选择 Network Setting OK For fingerprint + card identify, select this mode. Card + PIN Mode OK OK For card + pin identify, select this mode. Fingerprint + Card + PIN Mode OK For fingerprint + card + pin identify, select this mode. FCC Statements changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for Remark: 1. 1USB port is used to firmware upgrade purpose, without loading. 2. This device is installed on the wall. And the all the ports are in the wall. People can’t touch. 3. CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. 4. The minimum separation distance is 20 cm between the device and the user when the device is being operated by the user.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : A2TT5ZZ Create Date : 2012:12:05 09:05:36+08:00 Modify Date : 2012:12:25 09:34:45+08:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Format : application/pdf Creator : A2TT5ZZ Title : Mini-Gate User Manual-ACD100P-CG.cdr Creator Tool : CorelDRAW X5 Metadata Date : 2012:12:25 09:34:45+08:00 Producer : Corel PDF Engine Version 15.2.0.686 Document ID : uuid:a0332614-1935-4812-b4a8-7bd33e2900c4 Instance ID : uuid:973c3c63-0a09-4827-bf0d-4dc2743c4c77 Page Count : 3 Profile CMM Type : Lino Profile Version : 2.1.0 Profile Class : Display Device Profile Color Space Data : RGB Profile Connection Space : XYZ Profile Date Time : 1998:02:09 06:49:00 Profile File Signature : acsp Primary Platform : Microsoft Corporation CMM Flags : Not Embedded, Independent Device Manufacturer : IEC Device Model : sRGB Device Attributes : Reflective, Glossy, Positive, Color Rendering Intent : Perceptual Connection Space Illuminant : 0.9642 1 0.82491 Profile Creator : HP Profile ID : 0 Profile Copyright : Copyright (c) 1998 Hewlett-Packard Company Profile Description : sRGB IEC61966-2.1 Media White Point : 0.95045 1 1.08905 Media Black Point : 0 0 0 Red Matrix Column : 0.43607 0.22249 0.01392 Green Matrix Column : 0.38515 0.71687 0.09708 Blue Matrix Column : 0.14307 0.06061 0.7141 Device Mfg Desc : IEC http://www.iec.ch Device Model Desc : IEC 61966-2.1 Default RGB colour space - sRGB Viewing Cond Desc : Reference Viewing Condition in IEC61966-2.1 Viewing Cond Illuminant : 19.6445 20.3718 16.8089 Viewing Cond Surround : 3.92889 4.07439 3.36179 Viewing Cond Illuminant Type : D50 Luminance : 76.03647 80 87.12462 Measurement Observer : CIE 1931 Measurement Backing : 0 0 0 Measurement Geometry : Unknown Measurement Flare : 0.999% Measurement Illuminant : D65 Technology : Cathode Ray Tube Display Red Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Green Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Blue Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract)EXIF Metadata provided by EXIF.tools