| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 137434 |
| Application ID | Fr70b2J/Z1DIZB5T4A3nGQ== |
| Document Description | users manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 30.57kB (382069 bits) |
| Date Submitted | 2001-02-21 00:00:00 |
| Date Available | 2001-02-20 00:00:00 |
| Creation Date | 0000-00-00 00:00:00 |
| Producing Software | Acrobat PDFWriter 3.02 for Windows |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | (RFW-23)UserMan.PDF |
| Document Creator | Microsoft Word |
Radio Wireless 2-Wheel Mouse
User’s Guide
Model:RFW-23
Trademark Recognition
Windows, Office 97 and MS-IntelliMouse are registered trademarks of Microsoft Corp.
MN-RFW-23-NC
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may cause harmful interference
to radio communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
l Reorient of relocate the receiving antenna.
l Increase the separation between the equipment and receiver.
l Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
l Consult the dealer or an experienced radio/TV technician for help.
The changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Introduction
Congratulations on your purchase! Your new RF-Mouse is easy to install and offers you a host of
useful features. The Radio receiver can be conveniently placed to give you the freedom you need
while working. The vertical wheel allows you to scroll, or zoom in and out in a document. You can
program the mouse buttons to launch the NetJump or LuckyJump for a quick start to programs you
run frequently. And, your RF-Mouse has a unique ID code, so other RF (Radio Frequency) pointing
devices won’t affect your system.
Connecting the RF-Mouse Receiver
The RF-Mouse receiver connects to your computer in
the same way as a conventional mouse allowing you to
place the receiver wherever is convenient on your
desktop.
1. Locate the round 6-pin PS/2 mouse port on the back of
your computer.
2. Insert the PS/2 connector into the PS/2 port.
Locating the RF-Mouse Receiver
Your RF-Mouse has limitations on the range or distance from the
receiver. To make sure that your mouse sends and receives properly, refer
to the following:
1. For optimal performance, place the receiver at least 8 inches (20
centimeters) away from other electrical devices, such as the
computer, the monitor, or external storage drives.
2. The RF-Mouse should be no farther than 3.3 feet (1.0 meter) from
the mouse receiver. This will ensure optimal communication
between the mouse and receiver.
3. If you are working on a metallic surface, try using a mouse pad
and turning the receiver face down for better reception.
4. Switch frequency channels to prevent interference from other RF
pointing devices. (See the following section for more information.)
Selecting the Frequency Channel
The RF-Mouse operates on two
frequency channels. To prevent
interference when using two RF
Mice in close proximity a different
frequency channel should be used
for each mouse. Refer to the
following to change the frequency
channel for your mouse:
1. Set the frequency channel on the
receiver to 1 or 2.
2. Remove the battery cover from
the mouse (see the following
Inserting the Batteries section).
3. Set the frequency channel on the
mouse to 1 or 2. (The frequency
channel for mouse and receiver
must be the same.)
Inserting the Batteries
The RF-Mouse uses two AAA
batteries. For best performance,
use only alkaline batteries. Refer
to the following to insert the
batteries:
1. Press the up cover and
move to backward of the
mouse up cover as shown
here and remove the cover.
2. Insert the two AAA
batteries. (The correct
polarity is indicated on the
battery compartment
casing.)
3. Replace the cover.
Checking the Batteries power
To check the battery power, right-click the mouse
icon in the Taskbar. Choose the “Check RFMouse Status” option to display the RF-Mouse
Status window. The current battery percentage
charge is shown.
Installing the Mouse Software
Before you can take advantage of the many features your mouse offers, you must install the driver.
The driver is on the installation diskette that came packaged with your mouse.
Windows 95/98/Me/2000/NT4.0 installation
1.
2.
3.
4.
5.
Connect the mouse to your computer.
Insert the installation diskette into your floppy disk drive.
Click the Start button and then click Run.
In the Run dialog window, type A:\setup, where “A” is the letter of your floppy disk drive.
Click OK and follow the instructions on your screen to complete the installation.
The RF-Mouse ID code
Each RF-Mouse is assigned a unique ID code at manufacture, so the receiver only picks up the signal
from your mouse and prevents other RF-Mouse radio signals from operating on your computer. This
feature can also be disabled, allowing other RF-pointing devices to operate your computer.
Connecting the RF-Mouse ID Code
When the driver installation is finished your
computer reboots and the RF-Mouse window
(shown on the right) appears.
CONNECT ID: Move the RF-Mouse for a few
seconds to establish a connection, then click
Connect ID. The unique ID code of your mouse is
recognized and another RF pointing device will not
function on your computer.
Exit: Click Exit if no other RF pointing devices
are within 3 meters range or if you want other RF
pointing devices to be able to access your
computer.
Changing the RF-Mouse ID Code
You can use a new RF-Mouse on your computer without changing the Radio receiver; you just need to
change the ID code. Refer to the following:
1. Press [Shift + Alt + F11] or [Shift + Alt + F12] to call up the RF-Mouse ID Code window.
2. Move the RF-Mouse for a few seconds to establish a connection, then click Connect ID.
3. The new ID code is Connected and the RF-Mouse window closes.
4. Click Exit to close the RF-Mouse ID code window.
Identifying Components
The mouse is designed to fit snugly into your hand. The scroll wheel is
positioned on the top allowing for easy operation with the index finger.
Standard mouse buttons are positioned to either side of the scroll wheels
and can be reached comfortably with the index and ring fingers. A third
button is placed under the vertical wheel and can be easily clicked by
pushing down on the wheel.
The following pages will tell you how to configure the scroll wheels and
buttons to suit your specific needs.
Cleaning the Mouse
Clean the mouse regularly to ensure efficient operation. Refer to the following:
1. Rotate the housing cover counterclockwise until it unlocks and
remove it.
2. Remove the tracking ball.
3. Wash the tracking ball with warm water and soap then allow it to
dry.
4. Use a cotton swab and alcohol to clean the tracking rollers in the
housing.
5. Replace the tracking ball and the housing cover.
6. Rotate the housing cover clockwise until it locks in place.
IWHEELWORKS DOES THE HEAVY WORK!
With iWheelWorks driver/software installed, your Mouse is transformed into much more than just a
pointing device. See how easy scrolling through long documents or panning in drawing applications
becomes when using the scroll wheels. Office users should love this feature—
use the vertical wheel
to scroll through your document then just press the [Ctrl] key and use the same wheel to zoom in
for a close look. It even works in print preview! The third button can be programmed to launch
NetJump or LuckyJump—
two customizable toolbars that open all those useful programs that you
need so often with just one click. And, in easy-to-follow steps, create your own Command Menu
and with one click put all your favorite programs right under the cursor!The following table
provides an overview of the mouse functions.
Function
Description
Here’s how to do it
Vertical
Scroll
Lets you scroll
up or down in
the current
application
window.
To scroll up, move the vertical wheel
forward; to scroll down, move the wheel
back. See Wheel Tab on page 8 for more
information.
Horizontal Lets you scroll
to the left or
Scroll
right in the
current
application
window.
To scroll left, move the horizontal wheel
forward; to scroll right, move the wheel
back. See Wheel Tab on page 8 for more
information.
AutoScroll Use
AutoScroll in
Office 97compatible
applications to
scroll through
large
documents.
Activate AutoScroll from LuckyJump or
NetJump. The AutoScroll icon appears
over the vertical scrollbar. Move the
mouse in the direction you want to scroll.
The farther you move the AutoScroll icon
from the starting point, the faster the
scrolling. To stop AutoScroll, press any
mouse button.
Lets you
zoom in or out
when using
applications
that support
zoom
function.
In the Mouse Properties window select
the Wheel tab and check the “Wheel
Zoom for Office 97/2000” option (if you
don’t check this option you can hold the
[Ctrl] key while zooming with either
scroll wheel). Then use the horizontal
wheel to zoom in and out. See Wheel
Tab on page 8 for more information.
Zoom
LuckyJum
With one click
you can
choose from a
range of
commonly
used
commands to
launch.
In the Mouse Properties window select
the Buttons tab and then assign
LuckyJump in the drop-down menu for
the desired button. See Settings Tab and
Executing LuckyJump Commands on
page 8 and Take Your mouse on a Test
Run on page 15 for more information.
NetJump
Lets you
choose from
commands
commonly
used for Web
browsing.
In the Mouse Properties window select
the Buttons tab and then assign NetJump
in the drop-down menu for the desired
button. See Settings Tab and Executing
NetJump Commands on page 8 and Take
Your mouse on a Test Run on page 15 for
more information.
Command Create your
own
Menu
Command
Menu for
launching all
your favorite
programs.
In the Mouse Properties window select
the Settings tab and then click
New/Update. Follow the instructions on
your screen. See Creating Your Own
Command Menu on page 10 for more
information.
MOUSE PROPERTIES SETTINGS
From the Mouse Properties window you can customize many
settings for your mouse including button assignments, scroll
wheels and cursor movement. To open the Mouse Properties
window double-click on the mouse icon in the system tray.
The Mouse Properties window has six tabs that are described
below.
Buttons Tab
Button Assignments: Click the down arrow
to select the preferred function for each button.
(See the Settings Tab for more information.)
Double Click Speed: Increase the speed for
executing a double-click.
Button Configuration: Configure your mouse
for left- or right-hand use. The default setting
for buttons 1 and 2 will be reversed.
The particular mouse you purchased may
differ somewhat from the illustration
shown in the Buttons tab. The third
button on some models is positioned
under the vertical scroll wheel instead of
at the side as shown here.
Pointers Tab
The Pointers tab lets you change the way the
cursor appears. Click the down arrow under
Scheme and choose the setting you want. The
available pointers for each scheme are shown in
the pane below. You can browse to additional
pointers, then create your own scheme using
the Save As button.
Ø N
ote!
Motion Tab
Pointer Speed: Lets you adjust how fast the
cursor moves on the screen.
SnapTo Button: Check this box to
automatically have the cursor move to the
default button in each new dialog box or
window.
Sonar: When this box is checked, pressing and
releasing the [Ctrl] key will highlight the
cursor.
Trails: Check this box when you want your
cursor to display pointer trails. This option is
useful when using an LCD display that can
make the cursor difficult to see.
System
Tray
Wheel Tab
Wheel Mode: Select the Enhanced Dual Wheel
4D Wheel function mode radio button to enable
both vertical and horizontal wheels. When the
MS-IntelliMouse Compatible mode radio button
is selected only the vertical wheel will function.
Swap Vertical and Horizontal Wheel: Check
this box to swap the functions of the Horizontal
and Vertical Wheels.
Vertical Wheel/Horizontal Wheel: Check the
Reverse scrolling direction box to change the
scrolling direction when you turn the scroll
wheel. Select the Scroll or Scroll one “page” per
scroll unit radio button to set the scrolling speed
to suit your work habits.
Wheel Zoom for Office 97/2000: Check this
box to use the horizontal wheel to zoom in and
out when using applications that support this
function. You can still use the wheel to scroll
horizontally by positioning the cursor over the
horizontal scroll bar. When this option is
unchecked, you must press the [Ctrl] key while
turning the horizontal wheel to use the zoom
function.
Settings Tab
Command List: Shows all the available
commands (including User-defined Command
Menus) that you can assign to either the NetJump
or LuckyJump grids.
NetJump (top grid): The NetJump grid groups
commonly used Web-browsing commands. To
change a command, select a new one from the
Command List and click on the icon in the grid
that you want to change.
LuckyJump (bottom grid): The LuckyJump
grid groups all-purpose commands. To change a
command, select a new one from the Command
List and click on the icon in the grid that you
want to change.
User-defined Command Menu: Here you can
create your own command menu to suit your
specific needs. Click on New/Update…and
follow the onscreen instructions.
Apply Net/LuckyJump or the User-defined
Command Menu you define here from the
Buttons tab.
Executing NetJump Commands
NetJump combines commonly used tasks for Web browsing into one convenient grid and puts them
right under the cursor. To use NetJump, open the Mouse Properties window and select the
Buttons tab. Assign NetJump in the drop-down menu of the button you want. Click OK to close
the Mouse Properties window. Now click the assigned button to open the NetJump grid and
execute your command. (See the Settings Tab section above for instructions on customizing
NetJump.)
Executing LuckyJump Commands
LuckyJump combines commonly used tasks for Windows environments into one convenient grid
and puts them right under the cursor. To use LuckyJump, open the Mouse Properties window and
select the Buttons tab. Assign LuckyJump in the drop-down menu of the button you want. Click
OK to close the Mouse Properties window. Now click the assigned button to open the
LuckyJump grid and execute your command. (See the Settings Tab section above for instructions
on customizing LuckyJump.)
THE USER-DEFINED COMMAND MENU
Along with the LuckyJump and NetJump menus you can also create Command Menus to suit your
specific work habits. You may want to create a specific command menu for a particular application
and then assign it each time you work in that application.
Creating a Command Menu
Follow these instructions to create a new Command Menu:
1. Double-click the mouse icon in the system tray. In the Mouse Properties window select
the Settings tab.
2. Click New/Update…to open the User-defined Options window.
3. Click Add. The Add Menu window appears.
4. Enter a name (e.g., Test Command
Menu) for the new Command
Menu. Click Select Icon to
choose a new icon or click OK to
accept the default icon. The Userdefined Options window appears
with the new Test Command Menu
shown.
5. The Command Type: pane lets
you change the kind of command
to add. With the default
Application/Document selected,
click
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.2
Linearized : No
Page Count : 17
Creator : Microsoft Word
Create Date : 2001¦~1¤ë8¤é 05:58:43 PM
Title : (RFW-23)UserMan.PDF
Author :
Producer : Acrobat PDFWriter 3.02 for Windows
Keywords : ID:H8GRW23
Subject : 00E1961
EXIF Metadata provided by EXIF.tools