AAMP of Florida AAMP Global ISBT43 Bluetooth audio receiver with FM transmitter and charger User Manual

AAMP of Flordia, dba AAMP of America Bluetooth audio receiver with FM transmitter and charger

User Manual

BluStreamFMConnect your phone to your car for calls and musicIN-CARCONNECTIVITYISBT43Initial Setup1) Plug the charging end of the BluStream FM into your vehicle’s cigarette lighter port, or 12V poweroutlet2) The body of the BluStream FM has two important built-in features; a microphone and a controlbutton.a. Attach the body of the BluStream on the dash of the vehicle, using the supplied double-sidedtape.NOTE:Location is key. Ideally, the body of the BluStream FM should be placed where it has a clear line-of-sight of the driver. Thiswillprovide the best hands-freeperformance.b. The control button functions are described in the operationsection.3) Pair yourSmartphonea. Press and hold the control button on the BluStream FM for 10 seconds to enter pairing mode. The control button on the BluStream FMwillrapidlyflashBluewheninpairingmode.b. Open the Bluetooth menu on your smartphone and search for available accessoriesc. Select the BluStream FM from the list and select“Connect”d. With your Bluetooth phone connected to the BluStream FM, begin playback of music and it will stream to your selected FM radiostation.Operation1) Play your music through your vehicle (FM)a. Slide the selector switch on the BluStream FM, to select one of the 4 available FM transmissionstations.For best peformance, select a frequency that is not in use by a local radio station in your area.b. Tune your FM radio to the frequency that matches the selected setting on the BluStream FM.c. Begin music playback on your phone, and the audio will play though the vehicle on theselectedfrequency.2) Receiving a phonecalla. Press the control button once to answer an incoming call, when your phone isringing.NOTE:you must be on the proper station in order to hear the phone call through the vehicle.Control buttonThe control button on the body of the BluStream FM is used for several different functions, which are describedbelow:- Siri / VR: Press the controlbutton.- Redial: Press the control buttontwice.- Answer Incoming Phone Call: Press the FM control button, while your phone isringing.- End call: Press the control button, while in a phonecall.USB Charging PortBluStream FM features a 5Volt 1 Amp charging port which can be used to charge your smartphone, or otherdevice.For vehicles equipped with anauxiliaryaudio input (aux)An audio connection cable is included with the BluStream FM, which allows it to be plugged directly into yourvehicle’s auxiliary audio input (if equipped). This will provide superior audio quality, compared to thestandardFM output of the BluStream FM.All functions described in the Operation section apply when using the aux connection method. The only difference, is that the radio must be ontheaux source,notaspecificFMfrequency.1) Plug the smaller end of the aux cable into the body of the BluStream FM2) Plug the larger end of the aux cable into your vehicle’s auxinputNOTE:When using the aux connection method, the setting of the FM selector switch selection on the BluStream does notmatter.WARNING:This equipment may be reset by unintentional electrostatic discharge during operation. Exposure to direct sunlight or extreme heat may cause damageormalfunction.FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digitaldevice,pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thisequipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmfulinterference to radiocommunications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more ofthefollowing measures:1. Re-orientate or relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit different from that of which the receiver isconnected.4. Consult the dealer or an experienced radio / television technical for help.Notice : The changes or modifications not expressly approved by the party responsible compliance could void the user authority to operate theequipment.TechSupport:support@isimplesolutions.com866-788-4237
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should beinstalled and operated with minimum distance of 20 cm between the radiator and your body.This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmfulinterference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Suchmodifications could void the user’s authority to operate the equipment.

Navigation menu