ACD Elektronik X1310TC915 radio module for data transmission User Manual Integration Manual
ACD Elektronik GmbH radio module for data transmission Integration Manual
Integration Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3298310 |
| Application ID | BpM5cZrWR/1ylJDUUxLDeA== |
| Document Description | Integration Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 42.02kB (525199 bits) |
| Date Submitted | 2017-02-28 00:00:00 |
| Date Available | 2017-02-28 00:00:00 |
| Creation Date | 2017-02-03 16:26:38 |
| Producing Software | Microsoft® Word 2010 |
| Document Lastmod | 2017-02-23 11:14:54 |
| Document Title | Operating instructions X1310 ISM Transceiver - 915MHz |
| Document Creator | Microsoft® Word 2010 |
| Document Author: | Florian Schmid |
Integration manual Operating instructions X1310 ISM Transceiver - 915MHz Version: 1.4 © Copyright ACD Gruppe This document may not be duplicated or made accessible to third parties without permission. 160701-AU01_Operating_instructions _V1.4_en.doc 1 / 13 Contents Scope of delivery .......................................................................................... 3 Intended use ................................................................................................ 3 Handling ....................................................................................................... 4 Installation of the components ...................................................................... 4 Module description ....................................................................................... 5 4.1 5.1 5.1.1 5.1.2 5.1.3 5.2 5.3 5.3.1 5.3.2 5.3.3 5.3.4 5.4 Introduction ............................................................................................................... 5 Printed circuit board/module ................................................................................ 5 Environmental conditions ..................................................................................... 5 System ................................................................................................................. 5 Assembling the PCB module .................................................................................... 5 Pin assignment and designation ............................................................................... 6 X1 connector assignment (host interface) ........................................................... 6 X2 connector assignment (host interface) ........................................................... 6 X4 connector (HF cable/antenna connection) ..................................................... 6 HF cable ............................................................................................................... 6 Antennas ................................................................................................................... 6 Functional description .................................................................................. 7 6.1 6.2 6.3 6.4 6.5 10 Example for installation ............................................................................................. 4 Control commands and telegrams ............................................................................ 7 Control commands in command mode ..................................................................... 7 Control commands in data mode .............................................................................. 8 Data telegram............................................................................................................ 8 Acknowledgement telegram...................................................................................... 8 USA/Canada frequency table 915MHz......................................................... 9 Service and spare parts ............................................................................. 10 RSS COMPLIANCE STATEMENT............................................................. 11 End device labeling instructions ................................................................. 11 Author: 160701-AU01_Operating_instructions _V1.4_en.doc S. Maier / 17.02.02 2 / 13 1 Scope of delivery Module HF cable Antenna Check that all components are undamaged and that all package contents are present 2 Intended use The “X1310-ISM-Transceiver-915MHz” module is a radio module for data transmission in the ISM band (SUB-GHz range) with the transceiver assembly CC1310 from TI. This module is intended for the frequency range 902.000 – 928.00MHz. Do not use the system in explosive areas. Please observe all national regulatory requirements for wireless devices. The supplied components are intended exclusively for use with this module. NOTE NOTE NOTE NOTE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouil-lage est susceptible d’en compromettre le fonctionnement. 160701-AU01_Operating_instructions _V1.4_en.doc 3 / 13 3 Handling Read all instructions first before using the module! Do not drink any alcohol or take any drugs while using the module and follow the saftey instructions carefully! The utilization of non-approved components can lead to the destruction of the device. ATTENTION 4 Installation of the components The printed circuit board is attached to the four fixing holes in the application. The associated HF cable (length 100mm) is fixed to the application housing using the SMA socket and the associated fixing nut. One of the approved antennas (see Chap 5.4) is screwed onto the SMA socket. The HF cable’s U.FL connector is inserted onto the X4 connector on the printed circuit board. The printed circuit board is connected to the host system via the X1 or X2 connector. Unintended use of the interfaces should be avoided. ATTENTION All components must be disposed of properly at the end of their technical lifetime. ATTENTION 4.1 Example for installation The SMA connector has to be mounted on top of a ground plane. The antenna has to be mounted on the SMA connector. 160701-AU01_Operating_instructions _V1.4_en.doc 4 / 13 5 Module description 5.1 Introduction The “X1310-ISM-Transceiver-915MHz” module is a radio module for data transmission in the ISM band (SUB-GHz range) with the transceiver assembly CC1310 from TI. This module is intended for the frequency range 902.000 – 928.00MHz. Printed circuit board/module Printed circuit board material HF socket Interface Internal status indicator External status indicator Printed circuit board dimensions Fixing Weight 5.1.2 FR4 U.FL (MCX) RS232 (X1 / 4-pin); (X2 / 12-pin) 1 LED red/green (not assembled) 2 TTL outputs (transmit/receive) 46.23 x 45.47 x 15 mm (LxWxH) 4 bore holes Approx. 50 g Environmental conditions 0% – 95%, not condensing -30 °C to +70 °C -30 °C to +85°C Air humidity Operation temperature range Storage temperature 5.1.3 System Transceiver type/MCU Firmware/radio protocol Memory integrated Interface Internal status indicator External status indicator HF output power Sensitivity/transmission rate Modulation Power supply Approvals 5.2 CC1310 ARM Cortex-M3 (TI) Proprietary ACD radio protocol 64kB Flash (up to 128k possible) RS232; RxD, TxD, RTS, CTS 1 LED red/green (not assembled) 2 TTL outputs (transmit/receive) Approx. -10dBm to -12dBm -110dBm / 19.2kBaud GFSK +4 to +15Vdc, typ. 12mA (<25mA) USA/Canada FCC15.249.a; FCC-ID Assembling the PCB module Shielding cabinet Conne ctor X4 Connector X2 5.1.1 Connector X1 Assembling on the component side 160701-AU01_Operating_instructions _V1.4_en.doc Assembling on the solder side 5 / 13 5.3 5.3.1 Pin assignment and designation X1 connector assignment (host interface) Connector: 2-1445052-4 TE connectivity Suitable mating connector: MOLEX 43645-0400 (connector ) MOLEX 43030-001 (crimp contacts) Pin number 5.3.2 or suitable alternatives Description TxD (RS232) RxD (RS232) GND +12V X2 connector assignment (host interface) Connector: 114712 Erni Suitable mating connector: 114712 Erni Pin number 10 11 12 5.3.3 X4 connector (HF cable/antenna connection) Connector: 5.3.4 Description +3.3V nc LED_RX LED_TX nc RTS (RS232) TxD (RS232) Nc GND CTS (RS232) RxD (RS232) +12V U.FL-R-SMT(01) Hirose 73412-0110 Molex HF cable HF cable: K-2439-02 IMS Connector Systems 5.4 or or suitable alternatives Antennas The transceiver may only be operated with the two antennas listed below, as this would otherwise not comply with the approval! Antenna 1: CTA 915/0/WS/SM/H1 COMPOTEK or Antenna 2: CTA 920/0/WR/SM/W1 COMPOTEK 160701-AU01_Operating_instructions _V1.4_en.doc 6 / 13 6 Functional description The data to be sent is transmitted from the host via the RS232 interface to the “X1310-ISM-Transceiver915MHz” module and then GFSK modulated and transmitted by this module via the transmission level and antenna to a receiver module of the same type. This module is intended for the frequency range 902.000 – 928.00MHz. The frequency range is divided into 32 channels with a respective channel spacing of 750KHz (see Chap.7: USA/Canada frequency table 915MHz). The module can be configured via the RS232 interface using commands (see Chap. 6.2: Control commands in command mode, or Chap. 6.3: Control commands in data mode). 6.1 Control commands and telegrams Firstly, a common frequency from the frequency table in Chap. 7 is defined for all radio devices. The host checks whether the radio channel is available (LBT, Listen Before Talk). If this condition is met, data or acknowledgement telegrams are transmitted, after a random delay, via the RS232 interface to the X1310 transceiver, starting with an, followed by the and ending with an . Based on the received, the transceiver now switches on the HF carrier and, first of all, transmits a preamble and SYNC sign. The sequence previously received via the interface is then sent , , . The switches the HF carrier off again in the end. The length of a telegram is limited by the settable transmission timeout (see “Control commands in command mode” table under STO1..99) in order to not block the remaining infrastructure. The function is as follows on the receiving side: The receiver in X1310 continuously searches for the SYNC signs. If detected, the data received below is transmitted via the RS232 interface to the host up to the . If determined that the HF carrier is interrupted, the receipt is also terminated. The RF signal is GFSK modulated with a frequency deviation of ±14 kHz and a data rate of 19.2 kbit/s. The modulation parameters are fully determined by the internal register settings of the CC1310 radio IC and are independent on the signal at the interface. Together with the antennas listed in the user manual (5.4), the transmission power is below the limits given under §15.249 of CFR47. 6.2 Control commands in command mode After a reset, the set baud rate is output on the interface at 38400,N,8,1. You can enable command mode using the sequence +++. Command word SWV? KAN? KAN1..32 SDL? SDL1..31 RES BDC? BDC1.2,2.4,4.8,9.6,19.2,38.4,57.6 BDF? BDF1.2,2.4,4.8,9.6,19.2,38.4,57.6 DEF DEF? 160701-AU01_Operating_instructions _V1.4_en.doc (Version firmware 2.01) Returns the module’s firmware version. Channel query. Returns the set radio channel (default K16). Channel setting. Sets the desired radio channel. Transmission power query Transmission power setting (dummy command), no change due to compatibility matters. Reset radio module. COM baud rate query. Returned value is the set baud rate (default 38.4). Setting the COM baud rate. Example: BDC38.4 sets the baud rate to 38400,N,8,1 (default) Radio baud rate query. (default 19.2k). Setting the radio baud rate (dummy command), no change due to compatibility matters. Setting the default values. Returned value OK. Displaying the default values. 7 / 13 CFG? FSM0..1 FSM? STO1..99 STO? RSP0..9 RSP? SAV HELP EXIT 6.3 Displaying the configuration Field strength measurement. FSM0: Field strength measurement off. FSM1: Field strength measurement on. Query whether field strength measurement is on or off. Setting the transmission timeout in 100ms steps. (default 3s / max.9.9s) Returns the set transmission timeout. Setting the squelch. Returns the set squelch. Saving the setting. List of the command words Leave command mode. Command mode is left after a timeout (1min). Control commands in data mode The configuration can also be performed in data mode using control telegrams. . Example: Channel query KAN? return: KAN8 Example: Set channel to channel 12: KAN12 return: KAN12 6.4 Data telegram LBT applies (Listen Before Talk). STX switches the transmitter on ETB switches the transmitter off 6.5 Acknowledgement telegram A data telegram is acknowledged by an acknowledgement telegram. LBT applies (Listen Before Talk). STX switches the transmitter on ETB switches the transmitter off 160701-AU01_Operating_instructions _V1.4_en.doc 8 / 13 7 USA/Canada frequency table 915MHz Channels 32 Channel spacing: 750KHz. Channel 1: 903.500MHz Channel 2: 904.250MHz Channel 3: 905.000MHz Channel 4: 905.750MHz Channel 5: 906.500MHz Channel 6: 907.250MHz Channel 7: 908.000MHz Channel 8: 908.750MHz Channel 9: 909.500MHz Channel 10: 910.250MHz Channel 11: 911.000MHz Channel 12: 911.750MHz Channel 13: 912.500MHz Channel 14: 913.250MHz Channel 15: 914.000MHz Channel 16: 914.750MHz (def.) Channel 17: 915.500MHz Channel 18: 916.250MHz Channel 19: 917.000MHz Channel 20: 917.750MHz Channel 21: 918.500MHz Channel 22: 919.250MHz Channel 23: 920.000MHz Channel 24: 920.750MHz Channel 25: 921.500MHz Channel 26: 922.250MHz Channel 27: 923.000MHz Channel 28: 923.750MHz Channel 29: 924.500MHz Channel 30: 925.250MHz Channel 31: 926.000MHz Channel 32: 926.750MHz Frequency band: Transmission power: Channel raster: Duty cycle: SDLx 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Transmission power dBm Power μW/mW -12dBm 63μW (def.) -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW -12dBm 63μW 902.000 – 928.00MHz approx.-12dBm 750 kHz no limits 160701-AU01_Operating_instructions _V1.4_en.doc 9 / 13 8 Service and spare parts If you have service requests, or require spare parts, please contact: ACD Elektronik GmbH Engelberg 2 88480 Achstetten Germany Telephone: +49 7392 708 499 Fax: +49 7392 708 490 Email: info@acd-elektronik.de Use original spare parts only. 160701-AU01_Operating_instructions _V1.4_en.doc 10 / 13 9 RSS COMPLIANCE STATEMENT This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouil-lage est susceptible d’en compromettre le fonctionnement. 10 End device labeling instructions FCC notes for all hosts devices. The end device must be labeled with: Contains FCC ID: O2F-X1310TC915“ Contains IC: 9137A-X1310TC915 Labelling Requirements In addition following statement shall be placed on the device: 160701-AU01_Operating_instructions _V1.4_en.doc 11 / 13 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Where the product is so small or for such use that it is not practicable to place the statement on it, the statement can be placed in a prominent location in the instruction manual. Information to the user - For Class A devices the manual of the host shall include the following statement: NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. - For Class B devices the manual of the host shall include the following statement: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Modification of equipment The instruction manual of the host shall include the following statement: Changes or modifications made to this equipment not expressly approved by the party responsible for compliance may void the FCC authorization to operate this equipment. Special accessories Where special accessories such as shielded cables and/or special connectors are required to comply with the emission limits, the instruction manual shall include appropriate instructions on the first page of the text describing the installation of the device. Final Compliance of end product The integrator is responsible for the final compliance of the end product including this certified transmitter module. CFR 47 §15.101 give guidance in terms of applicable equipment authorization procedures of different end-products. Typically compliance to subpart 15 B (§15.107 and 15.109) Class A or B including verification of the subpart 15 C compliance (field strength of fundamental and out-of-band emissions) of the transmitter parameters apply. 160701-AU01_Operating_instructions _V1.4_en.doc 12 / 13 Simultaneous transmission When the host product supports simultaneous-transmission operations the host manufacturer needs to check if there are additional RF exposure filing requirements due to the simultaneous transmissions. When additional application filing for RF exposure compliance demonstration is not required (e. g. if the X1310ISM-Transceiver-915MHz module in combination with all simultaneously operating transmitters complies with the RF exposure simultaneous transmission SAR test exclusion requirements), the host manufacturer may do his own evaluation without any filing, using reasonable engineering judgment and testing for confirming compliance with out-of-band, restricted band, and spurious emission requirements in the simultaneous-transmission operating modes. If additional filing is required please contact the person at ACD Gruppe responsible for certification of the X1310-ISM-Transceiver-915MHz module. 160701-AU01_Operating_instructions _V1.4_en.doc 13 / 13
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Florian Schmid Create Date : 2017:02:03 16:26:38+01:00 Modify Date : 2017:02:23 11:14:54+01:00 Subject : Eigenschaften -THEMA- Language : de-DE Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : Florian Schmid Description : Eigenschaften -THEMA- Title : Operating instructions X1310 ISM Transceiver - 915MHz Creator Tool : Microsoft® Word 2010 Metadata Date : 2017:02:23 11:14:54+01:00 Producer : Microsoft® Word 2010 Document ID : uuid:df408f34-64c6-4d9b-95ef-e38378bdac39 Instance ID : uuid:83a13f0f-83c5-4e60-9b3c-18df5ea0e4a3 Page Count : 13EXIF Metadata provided by EXIF.tools