ACE&EASTMAN Rh 9820 Service Manual 9820SM_Cover1E User
2016-10-16
User Manual: ACE&EASTMAN Rh-9820 Service Manual
Open the PDF directly: View PDF
Page Count: 236 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- SAFETY INSTRUCTIONS
- 1. MACHINE SPECIFICATIONS
- 2. FUNCTION SETTINGS
- 3. READING/WRITING DATA
- 3-1. Precautions when handling CF cards (commercially available)
- 3-2. Structure of a CF card folder
- 3-3. Data read/write mode
- 3-4. Reading parameter data from the CF card
- 3-5. Writing parameter data to the CF card
- 3-6. Reading memory switch data from the CF card
- 3-7. Writing memory switch data to CF cards
- 3-8. Writing error log data to the CF card
- 3-9. Updating the main control program
- 3-10. Updating the panel control program
- 4. MECHANICAL DESCRIPTIONS
- 4-1. Upper shaft and Needle bar mechanisms
- 4-2. Zigzag and thread take-up mechanisms
- 4-3. Needle bar rocking mechanism
- 4-4. Feed mechanism
- 4-5. Presser foot mechanism
- 4-6. Cloth opening mechanism
- 4-7. Cutter mechanism
- 4-8. Looper mechanism
- 4-9. Spreader mechanism
- 4-10. Upper thread trimmer mechanism
- 4-11. Upper tension release mechanism
- 4-12. Upper thread take-up mechanism
- 4-13. Lower thread release and lower thread take-up mechanisms
- 4-14. Gimp thread take-up mechanism <-01 specifications only>
- 4-15. Lower thread trimmer mechanism
- 5. DISASSEMBLY
- 5-1. Covers and presser foot mechanism
- 5-2. Upper shaft motor unit mechanism
- 5-3. Feed mechanism
- 5-4. Lower thread tension mechanism
- 5-5. Spreader mechanism
- 5-6. Looper mechanism
- 5-7. Needle bar rocking mechanism
- 5-8. Looper base mechanism
- 5-9. Needle bar mechanism
- 5-10. Lubrication
- 5-11. Zigzag and thread take-up mechanisms
- 5-12. Upper shaft mechanism
- 5-13. Cutter mechanism
- 6. ASSEMBLY
- 6-1. Cutter mechanism
- 6-2. Needle bar mechanism (1)
- 6-3. Zigzag mechanism
- 6-4. Upper shaft mechanism
- 6-5. Thread take-up mechanism
- 6-6. Needle bar mechanism (2)
- 6-7. Y feed mechanism
- 6-8. Looper base mechanism
- 6-9. Needle bar rocking mechanism
- 6-10. Lower shaft mechanism
- 6-11. Looper mechanism
- 6-12. Spreader mechanism
- 6-13. Upper thread trimmer mechanism
- 6-14. Threading mechanism
- 6-15. Feed base mechanism
- 6-16. X feed mechanism
- 6-17. Lower thread tension mechanism
- 6-18. Upper shaft motor mechanism
- 6-19. Covers
- 6-20. Work clamp plate mechanism
- 6-21. Lower thread trimming mechanism
- 6-22. Upper cover mechanism (upper thread tension release and upper thread take-up mechanisms and upper thread path)
- 6-23. Routing the harnesses
- 6-24. Routing the air tubes
- 6-25. Lubrication and greasing and routing the oil tubes
- 7. ADJUSTMENTS
- 7-1. Adjusting the heights of the spreaders and loopers
- 7-2. Adjusting the zigzag width (stitch width)
- 7-3. Adjusting the zigzag base line position
- 7-4. Adjusting the needle and looper timing
- 7-5. Adjusting the looper stroke
- 7-6. Adjusting the height of the needle bar
- 7-7. Adjusting the clearance between the loopers and needle
- 7-8. Adjusting the needle guard
- 7-9. Adjusting the spreader installation positions
- 7-10. Adjusting the spreader timing
- 7-11. Adjusting the height of the throat plate
- 7-12. Changing the cutting length (Replacing the hammer)
- 7-13. Adjusting the cutting surface of the hammer
- 7-14. Adjusting the axial play of the hammer
- 7-15. Making the cutter driving shaft and driving shaft presser move together
- 7-16. Replacing the knife and adjusting its position
- 7-17. Adjusting the cutting pressure
- 7-18. Adjusting the work clamp lift amounts
- 7-19. Adjusting the work clamp positions
- 7-20. Adjusting the positions of the work clamp plates
- 7-21. Adjusting the cloth opening amounts
- 7-22. Adjusting the upper thread feeding amount
- 7-23. Adjusting the lower thread feeding amount <-01 specifications only>
- 7-24. Replacing and adjusting the upper movable knife
- 7-25. Replacing and adjusting the movable knife and fixed knife (for the lower thread and gimp) <-01 specifications>
- 7-26. Replacing and adjusting the movable knife and fixed knife (for the lower thread and gimp) <-02 specifications>
- 7-27. Adjusting the gimp trailing length <-02 specifications only>
- 7-28. Adjusting the position of the lower thread presser <-02 specifications only>
- 7-29. Adjustment of the phase for the take-up roller cam
- 7-30. Adjusting the needle bar and looper base turning center
- 7-31. Adjusting the upper thread loosening amount
- 7-32. Adjusting the lower thread loosening amount
- 7-33. Adjusting the looper base home position
- 7-34. Adjusting the feed base X home position and Y home position
- 7-35. Adjusting the needle up signal home position for the upper shaft and upper shaft motor
- 7-36. Adjusting the upper shaft stop position
- 7-37. Installing (replacing) the sub clamp on the left side
- 8. ELECTRICAL MECHANISM
- 9. ERROR CODES
- 10. TROUBLESHOOTING