ACE&EASTMAN Sc 380Em01 E SC380*P001 User Manual

2016-09-16

• CONTENTS
  • 1. DRIVE UNIT SAFETY INSTRUCTION
  • 2. POINTS OF CAUTION
  • 3. NAMES OF EACH PARTS
  • 4. INSTALLATION
    • 1. Installation of the motor
    • 2. Installation of the control box
    • 3. Installation of the pulley
    • 4. Mounting of the belt.
    • 5. Installation of the protective cover
    • 6. Installation of the position detector
    • 7. Connection of the lever unit
    • 8. Connection of the sewing machine and control box.
  • 5. WIRE AND GROUNDING
    • 1. Insertion of the power connector
    • 2. Connection of 3-phase power
    • 3. Power capacity
    • 4. When using the 3-phase 200 V class SC-380 with Single- phase 200 to 220 V class
    • 5. When using the single phase 100 V SC-380 with single phase 110 V to 120 V
    • or 3-phase 200 to 220 V SC-380 with 3-phase 220V to 240V
    • 6. To change solenoid voltage
    • 7. When using the single-phase 220V servomotor in the 380V area
  • 6. CONFIRMATION
    • 1. Before turning switches on...
    • 2. Thrn on the power...
  • 7. ADJUSTMENTS
    • 1. Adjustment of stopping position
    • 2. Adjustment of pedal toe down pressure, and heeling pressure
    • 3. Adjustment of operation speed
  • 8. PEDAL OPERATION
  • 9. OPERATION OF THE OPERATION PANEL KEYS
    • 1) Displays during normal mode and functions of each key
    • 2) Selection of each mode
    • 3) HOW TO USE PROGRAM MODES [1] AND [2]
    • Table of simplified setting value for JUKI sewing machine with thread trimmer
    • 4) How to use the normal mode
    • 5) Display and function of each key in the tacking mode and pattern mode. (for lock stitch machine)
      • (1) Tacking setting mode (At the time of patter No.=4, this mode will be skipped.)
      • (2) No. of tacking stitches setting mode.
      • (3) Preset stitching setting mode
  • 10. HOW TO USE THE PROGRAM MODE (EXAMPLE OF MOST FREQUENTLY USING)
    • 1) To change the maximum speed
    • 2) To change the number of stitches in slow start
    • 3) To apply a weak break during stopping
    • 4) To set the standing work type
    • 5) To change input/output port function
    • 6) To set external one shot signal
    • 7) To set number of stitches to the needle UP position stop after detecting the fabric end with an optical sensor, etc.
    • 8) To continue presser foot lifting after the thread trimming, and to bring down
    • the presser foot after the time set on the timer has passed
    • 9) To set needle position higher than usual after thread trimming
    • 10) To adjust the correlation between toe down angle speed
    • 11) To run without the detector (when the detector is broken)
    • 12) To adjust tacking accurately
    • 13) To check the error codee history and input/output signal
    • 14) To return all setting to the factory settings
  • 11. HOW TO SET COUNTER FUNCTION
    • 1. To use the counter function
    • 2. Down counter for bobbin remain thread count (10,000 stitches is count over)
    • 3. How to Adjust current count amount to use input signal.
  • 12. SETTING IN THE THREAD TRIMMING MODE TR
    • 1) Thread trimming timing when thread trimming mode TR setting is PRG
    • 2) Sewing machine motion pattern
  • 13. OUTPUT TB, TF TIMINGS
    • 1) Output normal timing
    • 2) Function setting [RU [ON]] in program mode P
  • 14. OUTPUT KS1, KS2, KS3 TIMINGS
  • 15. SIMPLE SEQUENCE
    • 1. Simple sequence starting conditions
    • 2. Simple sequence output timing chart
    • 3. When starting condition setting [SQS] is [NO] (default setting)
    • 4. Example of simple sequence setting
  • 16. COMMUNICATION FUNCTION
    • 1. About the communication
    • 2. Wiring
    • 3. The basic procedure
    • 4. The communication command list
  • 17. HOW TO CHANGE VOLTAGE OF PANEL CONNECTOR AND SOLENOID RETURN SPEED
    • 1. To change Solenoid voltage 24 V/30 V.
    • 2. How to change the output voltage DC5 V/12 V
    • 3. How to set the switch for increasing the solenoid return speed.
  • 18. HOW TO SET THREAD BREAK DETECTOR
    • 1. Setting Thread break detector function
    • 2. Timing chart of thread break input and output.
  • 19. CUTTER OUTPUT
    • 1) Cutter
    • 2) BT specifications (*1) operation chart and required settings
  • 20. TABLE OF PROGRAM MODE FUNCTIONS
  • 21. INPUT/OUTPUT FUNCTION FOR SIGNAL ON C MODE SETTING
    • 1. C mode input signal setting table
    • 2. C mode output signal setting table
  • 22. THE COMPOSITION FIGURE OF INPUT AND OUTPUT CUSTOMIZATION
    • 1. Input and output customization
    • 2. Input/output direct coupling port (inside connecting port)
    • 3. Connector input/output common port
  • 23. HOW TO USE THE OPTION CONNECTOR
    • 1) Connector layout
    • 2) The explanation of the input/output signal
    • 3) To use as a standing work type sewing machine.
  • 24. ERROR DISPLAY
  • 25. SPECIFICATIONS
  • <REFERENCE> TABEL OF DIGITAL DISPLAY
• Front page