ADC Telecommunications FWM0801A GSM Base Station User Manual Manual 2
ADC Telecommunications Inc GSM Base Station Manual 2
Contents
- 1. Manual 1
- 2. Manual 2
Manual 2
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1127082 |
| Application ID | Bo969IQ1GmD9r5ary+uHwA== |
| Document Description | Manual 2 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 190.48kB (2380955 bits) |
| Date Submitted | 2009-06-19 00:00:00 |
| Date Available | 2009-06-19 00:00:00 |
| Creation Date | 2009-04-30 15:08:59 |
| Producing Software | Acrobat Distiller 8.1.0 (Windows) |
| Document Lastmod | 2009-05-28 11:58:07 |
| Document Title | FlexWave micorBTS Installation and Commissioning Guide |
| Document Creator | FrameMaker 8.0 |
| Document Author: | ADC Wireless Network Solutions Technical Publications |
ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration 5.5 Assigning OML Link IP Address and a Static IP Address to the microBTS Depending upon your networks requirements, a network IP address will need to be assigned to the microBTS and each TRX. IP addresses should be obtained from your network administrator. Use the following step-by-step procedure to assign a new IP address to the microBTS. Find the IP address of the microBTS corresponding to the micro controller. The last MAC address listed on the exterior label will be the micro controller as shown in Figure 5-7. Match this MAC address with the DHCP assigned IP address as shown in Figure 5-12. Open a Web browser such as Explorer, Mozilla, etc. and using the familiar browser command: http:// xxx.xxx.xxx.xxx where xxx.xxx.xxx.xxx is the IP address assigned to the micro controller. The following screen will appear. Refer to Figure 5-15. AD030908 Figure 5-15: FlexWave microBTS Configuration Screen FlexWave microBTS Installation and Commissioning Guide Page 55 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration Using the configuration screen, type in the following information as shown in Table 5-1 Table 5-1: Configuration Parameters Parameter Variable microBTS Address Use an IP administrator address assigned by your system Subnet Mask Use an IP administrator address assigned by your system Gateway Use an IP administrator address assigned by your system nanoBTS 1 Use an IP administrator address assigned by your system nanoBTS 2 Use an IP administrator address assigned by your system Primary OML (operations and maintenance link) 1 Use the IP address assigned to the Abis link on which your BSC is operating Primary OML (operations and maintenance link) 2 Use the IP address assigned to the Abis link on which your BSC is operating a secondary link Use DHCP Page 56 © 2009, ADC Telecommunications, Inc. This is selected when a DHCP address needs to be assigned to the microBTS. Make sure that this is not selected if you are assigning static IP addresses FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration 5.6 Configuring a New Site Using the BSC Configuration Manager Utility Once the microBTS is configured with IP addresses, use the following procedure to launch, configure and verify that the microBTS is connected and functioning. Launch the BSC Configuration Manager from the PC’s desktop or file folder as shown in Figure 5-16. Launch the BSC configuration Manager AD069909 Figure 5-16: Launching the BSC Configuration Manager from a PC Desktop FlexWave microBTS Installation and Commissioning Guide Page 57 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration After the BSC Configuration Manager is launched, a connection screen will appear as shown in Figure 5-17. Type in the IP address of the BSC you wish to communicate with. Enter the password and click OK. AD069902 Figure 5-17: Connecting to the BSC screen A “tree” representation of your network will appear as shown in Figure 5-18. Click on the sites + symbol. This will show each BTS site on your network. Click on the Sites “+”Symbol To Reveal the BTS Sites on the Network AD069903 Figure 5-18: Reviewing the BTS Sites on the Network Page 58 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration A new site must be created for the microBTS configured in the previous sections. Right click on Sites and select Create. A Create SITE dialog box will appear as shown in Figure 5-19. AD069905 Figure 5-19: Creating a New Site A number of parameters will need to be input in the Create SITE dialog box as shown in Table 5-2: Table 5-2: Configuration Parameters Parameter Variable BTS Class From this pull-down menu, select the type of TRX(s) installed in the microBTS Site Name Select a site name according to the needs of your network Site Indentifier This number is normally assigned by a network administrator depending upon the needs of the network. The number must be unique to each site and can not be duplicated within a network. FlexWave microBTS Installation and Commissioning Guide Page 59 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration Table 5-2: Configuration Parameters Parameter Variable BTS Name Select a BTS name that is associated to the site name in your network Frequency Band Select the appropriate frequency band from the pull-down menu MCC Select an AFRCN channel number according to the needs of the network MNC Per network requirement Location Area Code (LAC) Per network requirement Cell Identity Per network requirement PLMN-CC Per network requirement BS-CC Per network requirement Once all of the above items are configured, click Finish and a new BTS site will be created. A new site will appear in the configuration “tree.” Note: For 2 x 1 configured microBTS a “slave TRX” must be added. Right click on the site object and select Create from the pull-down menu. A Create BTS Child Object screen will appear. Select Create TRX objects and click on OK. Refer to Figure 5-20. AD079901 Figure 5-20: Create BTS Child Object Screen Page 60 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration 10 A Create TRX screen will appear. Refer to Figure 5-21. 11 Fill in the dialog boxes with the information appropriate to your system. Refer to Table 5-2. Table 5-3: Configuration Parameters Parameter Variable nanoBTS Hardware Class From this pull-down menu, select the type of TRX(s) installed in the microBTS Radio Carrier Name Select a Radio Carrier Name according to the needs of your network Baseband Transceiver Name Select a Baseband Transceiver Name according to the needs of your network TRX Number In a 2 TRX system the Master = 0, the Slave = 1. 12 Once this information is added. 13 Click Finish to complete the process of adding a slave TRX. AD079902 Figure 5-21: Create TRX Screen FlexWave microBTS Installation and Commissioning Guide Page 61 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration 5.7 Creating the FlexWave Manager Right click on the FlexWave Manager object on the “tree” screen as shown in Figure 5-22. Select Create from the pull-down menu. AD079903 Figure 5-22: Using the FlexWave Manager Object to Launch the Create TRX Screen A Create microBTS screen will appear. Enter the name (the name will be choosen according to the needs of your network)and site identifier (the serial number located on the exterior label of the microBTS) in the dialog boxes indicated. Click Edit once the information is input. Refer to Figure 5-23. Page 62 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration AD079904 Figure 5-23: Create TRX Screen A Sites belonging to this microBTS dialog screen will appear. The site name entered in the previous steps will appear in the top portion of the screen. Click on the new site to highlight it. Click on the down arrow to move this site into the SITEs in this microBTS: shown on the lower portion of the screen and click OK. Refer to Figure 5-24. AD079906 Figure 5-24: Sites Belonging to this microBTS Screen FlexWave microBTS Installation and Commissioning Guide Page 63 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration A confirmation screen will appear that indicates the created site has been moved into the FlexWave Manager register. Refer to Figure 5-25. AD079907 Figure 5-25: Conformation SITEs Belonging to this Screen Return to the Create microBTS screen as shown in Figure 5-23 and click Finish. Return to the main screen and the new FlexWave Manager site object will appear as shown in Figure 5-26. Page 64 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration AD079909 Figure 5-26: New Site Object Appears on Configuration Manager “Tree” 10 Right click on the new site and select Properties. A configuration screen titled microBTS- (name of model) Properties... will appear. Select the Configuration tab. Refer to Figure 5-27. FlexWave microBTS Installation and Commissioning Guide Page 65 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration AD075904 Figure 5-27: Configuration Tab of the Site Properties Screen 11 Verify the serial/ identification number from the exterior model label of the microBTS matches the one obtained in Step 2. 12 Click on the FlexWave IP Address List Edit button and enter the OML Link IP address for your network. Click OK. Refer to Figure 5-28. AD078902 Figure 5-28: Verifying the FlexWave IP Address List Page 66 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration 13 Click on the Primary OML Address List Edit button and enter the OML Link IP address for your network. Click OK. Refer to Figure 5-29. AD078903 Figure 5-29: Verifying the Primary OML Address List FlexWave microBTS Installation and Commissioning Guide Page 67 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration 5.8 Verifying BTS Functionality Using the BSC Configuration Manager To verify the installed BTS is functioning, use the following procedure: Right click on the new site shown on the BSC Configuration Manager “tree” and a dialog box will appear. Select Unlock. The BTS will now begin transmitting on the AFRCN number selected in the previous steps. This can be verified at the site by means of an external power meter and frequency counter or a spectrum analyzer if available. Make a phone call by working in conjunction with the system administrator. Note: Further information regarding the configuration of the microBTS TRX units can be found in the instructions set forth in ADC publication ADCP-75-310 Page 68 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure Appendix A - Software Upgrade Procedure Content Page A.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 A.2 Upgrading Micro Controller Software from 4.0.x.x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 A.3 A.2.1 Automatic Upgrading of the microBTS Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 A.2.2 Manual Upgrade Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Upgrade Procedure for Micro Controller Software 3.2.x to Version 4.0.1.x. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 FlexWave microBTS Installation and Commissioning Guide Page 69 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure A.1 Introduction From time-to-time ADC may issue software upgrades in the interest of product improvement. The following upgrade procedure should be performed by an experienced field service technician who is familiar with linux operating systems. Caution: Failure to execute the procedure(s) exactly as given may render the microBTS inoperative. Page 70 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure A.2 Upgrading Micro Controller Software from 4.0.x.x The micro controller unit within the microBTS contains upgradable software, which from time-to-time may be upgraded. Note: The following procedure will require that the microBTS being upgraded be taken out of service for the duration of the upgrade process. This procedure provides two methods for upgrading the micro controller software. An “automatic” upgrade (preferred method) is accomplished through the use of a GUI type interface. The “manual” procedure relies on linux commands to accomplish the upgrade task. The “manual” upgrade method should only be used when circumstances preclude the use of the “automatic” upgrade and should be performed by an experienced linux operator. A.2.1 Automatic Upgrading of the microBTS Controller Launch a WinSCP session from the PC desktop and the WinSCP Login screen will appear. Refer to Figure A-1. Enter the Host name which is the IP address assigned to the micro controller unit of the microBTS being upgraded. Enter root in the User name dialog box, and your password in the Password dialog box. Click on Login when complete. AD091911 Figure A-1: WinSCP Login Screen FlexWave microBTS Installation and Commissioning Guide Page 71 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure A Warning screen will appear (if this is your first login). Select Yes. Refer to Figure A-2. AD091912 Figure A-2: WinSCP Warning Screen A Server prompt screen will appear. Enter your Password in the dialog box indicated and click OK. Refer to Figure A-3. AD091913 Figure A-3: WinSCP Server Prompt Screen Page 72 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure The main WinSCP will appear showing the contents of the drive on which the compressed .gz upgrade file is located and the root directory showing the files currently contained in the microBTS controller. Copy the upgrade files similar to FWBSSCtrl_4.0.x.x.gz to the root directory. Refer to Figure A-4. C: ADC AD091903 Figure A-4: Main WinSCP Screen Close the WinSCP window and open a PuTTY session with the BSC by entering the BSC IP address. Login as root. Enter your password. Refer to Figure A-5. FlexWave microBTS Installation and Commissioning Guide Page 73 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure AD091904 Figure A-5: PuTTY Login Screen At the command prompts, type the following commands: cd /var/lib/ipaccess/support ls -l Refer to Figure A-6. AD091905 Figure A-6: Entries on Command Line Page 74 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure 10 At the command line, type the following commands: cp /root/FWBSSCtrl_4.0.x.x.gz . ls -l Refer to Figure A-7. AD091906 Figure A-7: PuTTY Login Screen 11 Close the PuTTY window and launch BTS Configuration Manager. 12 Select Connect to BSC from the task bar. 13 Enter the IP address of the BSC and click OK. Refer to Figure A-8. FlexWave microBTS Installation and Commissioning Guide Page 75 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure AD091907 Figure A-8: Connect to BSC Screen 14 Right click on the FlexWave Manager object and select Properties. The FlexWave Manager Properties screen will appear. Verify that the nanoBTS Software Version dialog box contains the updated software version number. Refer to Figure A-9. will AD091908 Figure A-9: FlexWave Manager Properties Screen Confirming the New Software Load Page 76 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure 15 Return to the BSC Configuration Manager screen and find the BTS upgraded on the configuration “tree.” 16 Right click on the site and select Properties. The microBTS Properties screen will appear (this may take up to 10 minutes) showing the Active Software Version and the Standby Software Version. 17 Confirm the Standby Software Version is the version loaded on this procedure. After determining it is correct, Click OK. Refer to Figure A-10. will 4.0.1.9 AD091909 Figure A-10: microBTS Properties Screen Confirming the Active and Standby Software Loads 18 Return to the BSC Configuration Manager main screen and select BSC Control from the menu bar as shown in Figure A-11. 19 With the FlexWave Manager Object still selected, select Activate nanoBTS Software from the drop down menu. 20 When prompted to activate the new software click OK. FlexWave microBTS Installation and Commissioning Guide Page 77 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure will AD091910 Figure A-11: Activating the nanoBTS Software From the BSC Configuration Manager Main Screen 21 The microBTS is now upgraded with the new software load. The site can now be returned to normal operation. A.2.2 Manual Upgrade Procedure Upgrading of the micro controller software can be done using a procedure using linux commands to accomplish the upgrade task. The manual upgrade method should only be used when circumstances preclude the use of the “automatic” upgrade and should be performed by an experienced linux operator. Use the following step-by-step procedures: Launch a WinSCP session from the PC desktop and the WinSCP Login screen will appear. Refer to Figure A-12. Enter the Host name which is the IP address assigned to the micro controller unit of the microBTS being upgraded. Enter root in the User name dialog box, and your password in the Password dialog box. Click on Login when complete. Page 78 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure AD091911 Figure A-12: WinSCP Login Screen A Warning screen will appear. Select Yes. Refer to Figure A-13. AD091912 Figure A-13: WinSCP Warning Screen A Server prompt screen will appear. Enter your Password in the dialog box indicated and click OK. Refer to Figure A-14. FlexWave microBTS Installation and Commissioning Guide Page 79 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure AD091913 Figure A-14: WinSCP Server Prompt Screen The main WinSCP will appear showing the contents of the drive on which the compressed .gz upgrade file is located and the root directory showing the files currently contained in the microBTS controller. Copy the upgrade files which will appear similar to FWBSSCtrl_4.0.x.x.gz to the root directory. Refer to Figure A-15. Page 80 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure C: ADC AD091903 Figure A-15: Main WinSCP Screen Close the WinSCP window and open a PuTTY session with the BSC by entering the BSC IP address. Login as root. Enter your password. Open a PuTTY session and login as root. At the command line enter: hcp -v This will display the current version of the micro controller software. For example: hcp: version 4.0.1.3 At the command prompt enter: ls -l FlexWave microBTS Installation and Commissioning Guide Page 81 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure The output will appear similar to the following: total 105 -rw-r--r-- 1 root root 95965 2009-03-11 01:36 FWBSSCtrl_4.0.1.9.gz -rw-r--r-- 1 root root 1 2009-03-10 22:23 gothcp -rw-r--r-- 1 root root 2485 2009-03-10 22:43 got_info 10 At the command line enter: cd /usr/local/sbin ls Text similar to the following will appear showing the various files in the directory: batch.pem changeHcpVersion cluster_000810164.tgz ca.pem cluster_000810156.tgz certChainFile.pem hcp cluster-cert.pem oem.pem cluster_000810158.tgz cluster-key.pem 11 Make a temporary directory: mkdir tmp 12 Change to the temporary directory by entering: cd tmp 13 At the command line enter: To copy the upgrade file to the temporary directory cp /root/FWBBSSCtrl_4.0.1.9.gz 14 To unpack the tar file, type: tar -zxvf FWBSSCtrl_4.0.1.9.gz The following output will appear: adc.GIF hcp hcpInstall microBTS updatePod 15 Install the upgrade files by entering: ./hcpInstall The following output will appear: Page 82 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure ln: `/var/www/index.html': File exists Stopping hardware control process: hcp. 16 To change directories enter: cd .. 17 At the command line enter: hcp -v This will display the version number of the software upgrade loaded in this procedure. For example: hcp: version 4.0.1.9 18 This completes the manual upgrade procedure. Verify the new software is loaded by Closing the PuTTY window and launching BSC Configuration Manager. Select Connect to BSC from the task bar. Enter the IP address of the BSC and click OK. Refer to Figure A-16. AD091907 Figure A-16: Connect to BSC Screen 19 Right click on the FlexWave Manager object and select Properties. The FlexWave Manager Properties screen will appear. Verify that the nanoBTS Software Version dialog box contains the updated software version number. Refer to Figure A-17. FlexWave microBTS Installation and Commissioning Guide Page 83 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure will AD091908 Figure A-17: FlexWave Manager Properties Screen Confirming the New Software Load 20 Return to the BSC Configuration Manager screen and find the BTS upgraded on the configuration “tree.” 21 Right click on the site and select Properties. 22 The microBTS Properties screen will appear showing the Active Software Version and the Standby Software Version. Confirm the Standby Software Version is the version loaded in this procedure. 23 After determining it is correct, Click OK. Refer to Figure A-18. Page 84 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure will 4.0.1.9 AD091909 Figure A-18: microBTS Properties Screen Confirming the Active and Standby Software Loads 24 The manual upgrade of the microBTS controller is now complete. FlexWave microBTS Installation and Commissioning Guide Page 85 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure A.3 Upgrade Procedure for Micro Controller Software 3.2.x to Version 4.0.1.x. Use the following “manual” upgrade procedure to upgrade microBTS controller software from version 3.2.x to 4.0.1.x. 3.2.x versions of the micro controller software will not display IP or MAC addresses on the BTS Installer Utility. The MAC and IP addresses for the micro controller can be found using the following methods: Launch the BTS Installer Utility as shown in Figure A-19 and click on the Find button. AD098901 Figure A-19: Selecting Find on the BTS Installer Utility A Select nanoBTS screen will appear. The MAC and IP addresses of the nano TRX’s with in the microBTS will be shown. Refer to Figure A-20. Page 86 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure Confirm that the MAC addresses shown match those shown on the exterior label of the microBTS. The IP address for the micro controller is normally one digit higher than the highest IP address of the nano TRX’s. In the sample shown, the highest nano TRX is 172.16.79.15. It is likely that the micro controller address will be 172.16.79.16. Record this number for use in the next step. 172.16.79.14 00:02:95:00:42:17 1/0/0 172.16.79.15 00:02:95:00:42:AD 2/0/0 AD098902 Figure A-20: Select nanoBTS Screen Showing the MAC and IP Addresses for the nano TRX’s Use the IP address from the previous step to launch the WinSCP session in the next step. If the IP address does not work, use Wireshark, Angry IP or similar IP discovery tool to obtain the micro controller IP address. Launch a WinSCP session from the PC desktop and the WinSCP Login screen will appear. Refer to Figure A-21. Enter the Host name which is the IP address assigned to the micro controller unit of the microBTS being upgraded. Enter root in the User name dialog box, and your password in the Password dialog box. Click on Login when complete. FlexWave microBTS Installation and Commissioning Guide Page 87 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure AD091911 Figure A-21: WinSCP Login Screen 10 A Warning screen will appear. Select Yes. Refer to Figure A-22. AD091912 Figure A-22: WinSCP Warning Screen 11 A Server prompt screen will appear. enter your Password in the dialog box indicated and click OK. Refer to Figure A-23. Page 88 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure AD091913 Figure A-23: WinSCP Server Prompt Screen 12 The main WinSCP will appear showing the contents of the drive on which the compressed .gz upgrade file is located and the root directory showing the files currently contained in the microBTS controller. Copy the upgrade files which will appear similar to FWBSSCtrl_4.0.x.x.gz to the root directory. Refer to Figure A-24. C: ADC Figure A-24: Main WinSCP Screen FlexWave microBTS Installation and Commissioning Guide Page 89 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure 13 Close the WinSCP window and open a PuTTY session with the BSC by entering the BSC IP address. Login as root. Enter your password. Refer to Figure A-25. AD091904 Figure A-25: PuTTY Login Screen 14 At the command line enter: cd /usr/local/sbin ls Text similar to the following will appear showing the various files in the directory: batch.pem changeHcpVersion cluster_000810164.tgz ca.pem cluster_000810156.tgz certChainFile.pem hcp cluster-cert.pem oem.pem cluster_000810158.tgz cluster-key.pem 15 Make a temporary directory: mkdir tmp 16 Change to the temporary directory by entering: cd tmp 17 To copy the upgrade file to the temporary directory cp /root/FWBBSSCtrl_4.0.1.x.gz 18 To unpack the tar file tar -zxvf FWBSSCtrl_4.0.1.x.gz Page 90 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure The following output will appear: adc.GIF hcp hcpInstall microBTS updatePod 19 Display the software version number by entering: hcp -v This will display the current version of the micro controller software. For example: hcp: version 3.2.7 20 Back up /etc/inventory files by changing directory to the etc directory. In the etc directory enter: tar -cvf /root/inventory.tar /etc/inventory 21 At the command prompt enter: cd /etc 22 Using a text editor such as vi modify the file in the /etc/inittab by commenting out the last line which should appear similar to this: #hcp:2:respawn:/usr/local/sbin/hcp -nondaemon If this line does not exist in the files proceed to the next step. 23 At the command prompt enter: telinit q This will stop the hcp (micro controller process). 24 Change the directory by entering: cd thttpd 25 Verify the /etc/thttpd/thttpd.conf. Using a text editor such as vi, comment out the chroot line and changing the cgipat line at the bottom to include 2 asterisks instead of one: cgipat=/cgi-bin/** 26 Change the directory to by entering: cd / var /www 27 List the contents of the directory by entering: ls -l 28 If no directory exists, create one by entering: FlexWave microBTS Installation and Commissioning Guide Page 91 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure mkdir cgi-bin 29 Open the cgi-bin directory by entering: cd cgi-bin 30 Copy the contents by entering: cp /usr/local/sbin/tmp/* . 31 Change directories by entering: cd /var/www 32 Create a cgi-bin subdirectory in the /var/www directory and place the three files from the Html sub-project “microBTS”, “updatePod”, and “adc.GIF” into the cgi-bin directory. 33 At the :/etc/thttpd# prompt enter: cd /var/www 34 Display the contents of the directory by entering: ls -l 35 The screen will now show: total 2 drwxr-xr-x 2 root root 1024 2009-04-08 01:26 cgi-bin lrwxrwxrwx 1 root root cgi-bin/microBTS drwxr-xr-x 16 2009-04-08 01:26 index.html -> 2 root root 1024 2006-10-31 11:50 users 36 At the :/var/www# prompt enter: cd cgi-bin/ 37 At the :/var/www/cgi-bin# prompt enter: ls -l The screen will now show: total 44 -rwxr--r-- 1 root root 1690 2009-03-10 18:36 adc.GIF -rwxr-xr-x 1 root root 18517 2009-03-10 18:36 microBTS -rwxr-xr-x 1 root root 21191 2009-03-10 18:36 updatePod 38 Change the privledges on the ADC gif file by entering: chmod 744 adc.GIF 39 Change the privledges on the microBTS file by entering: chmod 775 microBTS Page 92 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure 40 Change the privledges on the updatepod file by entering: chmod 775 updatePod 41 At the :/var/www/cgi-bin# prompt enter: ls -l 42 The screen will now show (make sure that the files shown have the permissions as listed below): total 44 -rwxr--r-- 1 root root 1690 2009-03-10 18:36 adc.GIF -rwxrwxr-x 1 root root 18517 2009-03-10 18:36 microBTS -rwxrwxr-x 1 root root 21191 2009-03-10 18:36 updatePod 43 Change the directory by entering: cd /etc 44 Modify the /etc/inittab back to its original state. Using a text editor such as vi works uncomment the last line so it appears as: 45 At the command prompt enter: cd /usr/local/sbin ls Text similar to the following will appear showing the various files in the directory: batch.pem hcp changeHcpVersion cluster_000810164.tgz ca.pem oem.pem cluster_000810156.tgz cluster-cert.pem certChainFile.pem cluster_000810158.tgz cluster-key.pem 46 Make a temporary directory by entering: mkdir tmp 47 Change to the temporary directory by entering: cd tmp 48 Copy the upgrade package by entering: cp /root/FWBBSSCtrl_4.0.1.x.gz . 49 Unpack the upgrade package by entering: tar -zxvf FWBSSCtrl_4.0.1.x.gz FlexWave microBTS Installation and Commissioning Guide Page 93 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure The following output will appear: adc.GIF hcp hcpInstall microBTS updatePod 50 At the command prompt enter: ./hcpInstall The following output will appear: ln: `/var/www/index.html': File exists Stopping hardware control process: hcp. 51 At the command prompt enter: hcp -v This will display the version number of the software upgrade loaded in this procedure. For example: hcp: version 4.0.1.x 52 This completes the manual upgrade procedure. Verify the new software is loaded by closing the PuTTY window and launching BTS Installation Manager. 53 Select Connect to BSC from the task bar. 54 Enter the IP address of the BSC and click OK. Refer to Figure A-26. Page 94 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure AD091907 Figure A-26: Connect to BSC Screen 55 Right click on the FlexWave Manager object and select Properties. The FlexWave Manager Properties screen will appear. Verify that the nanoBTS Software Version dialog box contains the updated software version number. Refer to Figure A-27. will AD091908 Figure A-27: FlexWave Manager Properties Screen Confirming the New Software Load 56 Return to the BSC Configuration Manager screen and find the BTS upgraded on the configuration “tree.” Right click on the site and select Properties. FlexWave microBTS Installation and Commissioning Guide Page 95 © 2009, ADC Telecommunications, Inc. ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure 57 The microBTS Properties screen will appear showing the Active Software Version and the Standby Software Version. Confirm the Standby Software Version is the version loaded in this procedure. After determining it is correct, Click OK. Refer to Figure A-28. will 4.0.1.9 AD091909 Figure A-28: microBTS Properties Screen Confirming the Active and Standby Software Loads Page 96 © 2009, ADC Telecommunications, Inc. FlexWave microBTS Installation and Commissioning Guide ADCP-77-086 • Issue 1 • 10/2008 • Back Cover Blank FlexWave microBTS Installation and Commissioning Guide Page 97 © 2009, ADC Telecommunications, Inc. PHONE: U.S.A. or CANADA Sales: 1-800-366-3691 Extension 73000 Technical Assistance: 1-800-366-3891 Connectivity Extension: 73475 Wireless Extension: 73476 EUROPE Sales Administration: +32-2-712-65 00 Technical Assistance: +32-2-712-65 42 EUROPEAN TOLL FREE NUMBERS Germany: 0180 2232923 UK: 0800 960236 Spain: 900 983291 France: 0800 914032 Italy: 0800 782374 ASIA/PACIFIC Sales Administration: +65-6294-9948 Technical Assistance: +65-6393-0739 ELSEWHERE Sales Administration: +1-952-938-8080 Technical Assistance: +1-952-917-3475 13944-P WRITE: ADC Telecommunications (S’PORE) PTE, LTD; 100 Beach Road, #18-01, Shaw Towers. Singapore 189702. ADC Telecommunications, INC PO Box 1101, Minneapolis, MN 55440-1101, USA ADC European Customer Service, INC Belgicastraat 2, 1930 Zaventem, Belguim PRODUCT INFORMATION AND TECHNICAL ASSISTANCE: connectivity.tac@adc.com wireless.tac@adc.com euro.tac@adc.com asiapacific.tac@adc.com REPRINTS: PDF copies of manuals are available for downloading at the following link: www.adc.com/manuals ADCP Number: ADCP-77-086 Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice. In no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits and ADC further disclaims any and all liability for indirect, incidental, special, consequential or other similar damages. This disclaimer of liability applies to all products, publications and services during and after the warranty period. Website: www.adc.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Tagged PDF : Yes Page Mode : UseOutlines XMP Toolkit : 3.1-701 Format : application/pdf Description : FlexWave micorBTS Installation and Commissioning Guide Title : FlexWave micorBTS Installation and Commissioning Guide Creator : ADC Wireless Network Solutions Technical Publications Producer : Acrobat Distiller 8.1.0 (Windows) Creator Tool : FrameMaker 8.0 Modify Date : 2009:05:28 11:58:07-07:00 Create Date : 2009:04:30 15:08:59Z Metadata Date : 2009:05:28 11:58:07-07:00 Document ID : uuid:213d85fc-2d2e-43c0-b882-813f24000597 Instance ID : uuid:7c077720-4bb9-11de-9912-00145128619e Has XFA : No Page Count : 46 Subject : FlexWave micorBTS Installation and Commissioning Guide Author : ADC Wireless Network Solutions Technical PublicationsEXIF Metadata provided by EXIF.tools