ADC Telecommunications PSM7A7UD FlexWave Prism HDM 700 Lower ABC/Upper C User Manual RF modules installation guide

ADC Telecommunications Inc FlexWave Prism HDM 700 Lower ABC/Upper C RF modules installation guide

UserManual.wiki >

ADC Telecommunications >

PSM7A7UD User Manual HTML Version

RF modules installation guide

TECP-77-141  Issue 5  November 2013

300001744178 Rev E

Dual-Band Dual-Slot RF Module

Single-Slot RF Module

Dual-Slot 40W RF Module HDM RF Module

FlexWave Prism®

RF Modules for Prism Remote Units

Installation Guide

Information contained in this document is company private to TE Connectivity Ltd., and shall not be modified,

used, copied, reproduced or disclosed in whole or in part without the written consent of TE.

Trademark Information

FlexWave, FlexWave Prism, InterReach Spectrum, InterReach Unison, Universal Radio Head, TE

Connectivity, and TE connectivity (logo) are trademarks.

All other logos, products and/or company names referred to herein might be trademarks of their respective

owners.

Disclaimer of Liability

Contents herein are current as of the date of publication. TE reserves the right to change the contents without

prior notice. Should the content of printed user documentation shipped with product differ from documentation

provided on a product CD (inclusive of the associated Help modules), the printed user documentation

supersedes the documentation on the product CD. In no event shall TE be liable for any damages resulting

from loss of data, loss of use, or loss of profits, and TE further disclaims any and all liability for indirect,

incidental, special, consequential or other similar damages. This disclaimer of liability applies to all products,

publications and services during and after the warranty period.

Specific Disclaimer for High-Risk Activities

This Product is not specifically designed, manufactured, tested or intended for use in high-risk activities

including, without restricting the generality of the foregoing, on-line control of aircraft, air traffic, aircraft

navigation or aircraft communications; or in the design, construction, operation or maintenance of any nuclear

facility. TE (including its affiliates) and its suppliers specifically disclaim any express or implied warranty of

fitness for such purposes or any other purposes.

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 1

TABLEOFCONTENTS

Preface .................................................................................................................................................................2

RevisionHistory...................................................................................................................................................... 2

FlexWavePrismUserDocumentation.................................................................................................................... 3

DocumentCautionsandNotes .............................................................................................................................. 3

AccessingUserDocumentationontheTECustomerPortal .................................................................................. 4

StandardsCertification........................................................................................................................................... 5

OverviewofRFModulesforPRUs ........................................................................................................................6

PRURFModuleTypes ............................................................................................................................................ 7

PrismRemoteUnitSingle‐andDual‐CardRFModules ......................................................................................................8

PrismRemoteUnitHDMRFModules ................................................................................................................................9

PrismRemoteUnitDual‐Slot40WRFModules................................................................................................................10

SupportedRFModules......................................................................................................................................... 10

RFModuleComponents .....................................................................................................................................12

DuplexerandLowNoiseAmplifier.......................................................................................................................13

LinearPowerAmplifiers ....................................................................................................................................... 13

DigitalProcessingModule.................................................................................................................................... 14

UnderstandingtheRFModuleCables .................................................................................................................15

PowerCableConnection ...................................................................................................................................... 15

LVDSCableConnections....................................................................................................................................... 15

RFCableConnections........................................................................................................................................... 15

RFCableRules ..................................................................................................................................................................16

RFModuleCablesforSingle‐Card,Dual‐Card,andHDMRFModules .............................................................................16

RFModuleCablesforDual‐SlotInstallations ...................................................................................................................17

RFGroupAssignmentsforPRUs........................................................................................................................... 18

InstalltheRFModule(s)......................................................................................................................................21

SafetyPrecautions................................................................................................................................................ 21

GuardagainstDamagefromElectro‐StaticDischarge ......................................................................................... 22

UnpackandInspecttheRFModule ..................................................................................................................... 22

RemoveReleaseLinersfromtheRFModule ....................................................................................................... 23

Dual‐SlotModulesOnly—RemovetheModuleSlotShelf ................................................................................... 25

InstalltheRFModuleintothePrismRemoteChassis.......................................................................................... 26

SecureRFModuleLatches ................................................................................................................................... 34

ConnectLatchesonSingle‐SlotandHDMRFModules ....................................................................................................35

ConnectLatchesonDual‐BayDual‐SlotRFModules........................................................................................................36

LatchesonDual‐Slot40WRFModules.............................................................................................................................37

VerifythattheRFModuleMountingHookisEngaged ....................................................................................................37

ConnecttheRFModuleCables ............................................................................................................................ 37

ConnectingCablesinaSingle‐SlotRFModuleInstallation ..............................................................................................38

ConnectingCablesinaDual‐SlotRFModuleInstallation.................................................................................................40

PowerontheRFModule...................................................................................................................................... 45

ContactingTEConnectivity .................................................................................................................................46

ContactingTEConnectivitybyTelephone............................................................................................................ 46

ContactingTEConnectivityOnline ....................................................................................................................... 46

Preface

Page 2 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

PREFACE

ThismanualprovidestheinformationyouneedtoinstallTEConnectivityFlexWavePrism®RF

ModulesintoaPrismRemoteUnit(PRU).Installationinstructionsareprovidedforthefollowing

PrismRemoteUnitRFModules:

•Single‐SlotRFModules,whichincludestheHDMRFModules

•Dual‐SlotRFModules

–Dual‐CardRFModules

–40WRFModules.

NOTE: ThisinstallationguidedocumentstheRFModulesthatarecompatiblewiththeFlexWavePrism

RemoteUnit,whichisdesignedforoutdooruse.ForinformationontheRFModulesdesignedfor

usewiththeFlexWavePrismIndoorRemoteUnits(IRUs),seetheFlexWavePrismIndoorRemote

UnitInstallationGuide(TECP‐77‐197).

RevisionHistory

Table 1. Revision History

Issue Document Date Technical Updates

1April 2012 Original

2February 2013 Changed Prism remote Unit model names from Single-/Dual-/Tri-/Quad-Band to

Single-/Dual-/Tri-/Quad-Bay; updated Table 4 on page 10 to add new RF Modules; removed the

Specifications section, which included the RF and Optical Specifications and the Frequency and

Composite Output Power at Antenna Port (dBm) for Prism Remote Units tables; to access these

performance specifications, refer to the FlexWave Prism Performance Specifications (TECP-77-201);

updated “Contacting TE Connectivity” on page 46.

3May 2013 Updated “Accessing User Documentation on the TE Customer Portal” on page 4; added

“Understanding the RF Module Cables” on page 15; updated “Connect the RF Module Cables” on

page 37.

4October 2013 Added support for the following HDM RF Modules, in conjunction with Prism EMS Software Release

8.1.1: HDM AWS Band 4 MIMO 20W; HDM AWS Band 4 SISO 40W; HDM PCS Band 25 SISO 40W

(see Table 4 on page 10); updated Table 2 on page 3.

5November 2013 Adds support for the

FlexWave Prism User Documentation

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 3

FlexWavePrismUserDocumentation

FlexWavePrismuserdocumentationisintendedforsystemadministrators,engineersand

installersresponsibleforplanning,administering,configuring,andmaintainingFlexWavePrism

systems.Table2liststhemanualsthatcorrespondtothefeaturesoftheFlexWavePrismEMS

describedinthisguide.

DocumentCautionsandNotes

Twotypesofmessages,identifiedbelow,appearinthetext:

CAUTION! Cautionsindicateoperationsorstepsthatcouldcausepersonalinjury,induceasafetyproblem

inamanageddevice,destroyorcorruptinformation,orinterruptorstopservices.

NOTE: Notescontaininformationaboutspecialcircumstances.

Table2.FlexWavePrismUserDocumentation

Title Catalog Number

FlexWavePrismSoftwareRelease8.1SystemSetupandProvisioningGuide(1) TECP-77-214

FlexWavePrismSoftwareRelease8.1.1PerformanceSpecifications(2) TECP-77-229

HostUnitIIInstallationGuide TECP-77-206

HostUnitExpansionUnitInstallationGuide TECP-77-202

HostUnitIIandHostUnitExpansionUnitModuleReplacementGuide TECP-77-207

PrismRemoteUnitInstallationGuide TECP-77-142

RFModulesforPrismRemoteUnitsInstallationGuide(3) TECP-77-141

IndoorRemoteUnitInstallationGuide TECP-77-197

OADMSpliceBoxInstallationGuide TECP-77-208

CoarseWavelengthDivisionMultiplexerUserGuide TECP-77-209

1 Release 8.1 is the earliest release of the FlexWave Prism EMS that supports the hardware features described in this

installation guide.

2 Release 8.1.1 is the earliest release of the FlexWave Prism EMS that supports the RF Modules added to this

installation guide; see “Revision History” on page 2.

3 The Prism Remote RF Modules and Remote Mounting Kit are designed for use only in the Prism Remote Unit (PRU).

The IRU RF Modules and mounting options are described in the FlexWave Prism Indoor Remote Unit Installation

Guide (TECP-77-197).

Preface

Page 4 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

AccessingUserDocumentationontheTECustomerPortal

1ClickonthefollowingURLlink:

https://www.te.com/portal/wireless/

(Alternatively,entertheprecedingURLintoyourwebbrowser,andthenpressENTERonyour

keyboard.)

2AccesstotheCustomerPortalrequiresauseraccountandpassword.OntheSign Inpage,do

oneofthefollowing:

3OntheWirelessCustomerPortalhomepageintheKnowledge Centerpanel,clicktheManualsand

DataSheetslink.

4OntheManualsandDataSheetspage,dothefollowing:

aIntheDocument Repositorypanel,scrolltothesectionfortheproductlineofthedocument

thatyouwanttoaccess.

bClickonthetitleofthemanualthatyouwishtoopen.

c(Optional)SavethePDFtoyourPCorlaptop.

If you have an

account, enter

your Email and

Password and

click Sign In.

If you don’t

have an

account, click

and follow the

prompts.

Standards Certification

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 5

StandardsCertification

FCC:ThisequipmentcomplieswiththeapplicablesectionsofTitle47CFRPart15(HostUnit),Part

22(800MHzCellular),Part24(1900MHz‐PCS),Part90(800/900‐SMR),andPart27

(2100MHz‐AWS)&(700MHz‐LTE).

IC:ThisequipmentcomplieswiththeapplicablesectionsofRSS‐131.Theterm“IC:”beforethe

radiocertificationnumberonlysignifiesthatIndustryCanadaTechnicalSpecificationsweremet.

TheManufacturer'sratedoutputpowerofthisequipmentisforsinglecarrieroperation.For

situationswhenmultiplecarriersignalsarepresent,theratingwouldhavetobereducedby3.5

dB,especiallywheretheoutputsignalisre‐radiatedandcancauseinterferencetoadjacentband

users.Thispowerreductionistobebymeansofinputpowerorgainreductionandnotbyan

attenuatorattheoutputofthedevice.

Note:TocomplywithMaximumPermissibleExposure(MPE)requirements,themaximum

compositeoutputfromtheantennacannotexceed1000WattsERP(LTE,CellularandSMR),the

antennacannotexceed1640WattsEIRP(PCSandAWS),andtheantennamustbepermanently

installedinafixedlocationthatprovidesatleast6meters(20feet)ofseparationfromallpersons.

UL/CUL:Thiswillbeinstalledinarestrictedaccesslocation.ThisequipmentcomplieswithType

4,perULandCUL50,StandardforEnclosuresforElectricalEquipment.Thisequipmentprovides

thedegreeofprotectionspecifiedbyIP66asdefinedinIECPublication529.

FDA/CDRH:ThisequipmentusesaClass1LASERaccordingtoFDA/CDRHRules.Thisproduct

conformstoallapplicablestandardsof21CFRPart1040.

Caution:Modificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecould

voidtheuser'sauthoritytooperatetheequipment.

EUHarmonizedStandards:MeetsessentialrequirementsofR&TTE1999/5/EC.

•Article3.1a—Theprotectionofthehealthandthesafetyoftheuserandanyotherperson,

includingtheobjectiveswithrespecttosafetyrequirementscontainedinDirective

2006/95/EC,butwithnovoltagelimitapplying.

•Article3.1b—Theprotectionrequirementswithrespecttoelectromagneticcompatibility

containedinDirective2004/108/EC.

•Article3.2—Inaddition,radioequipmentshallbesoconstructedthatiteffectivelyuses

thespectrumallocatedtoterrestrial/spaceradiocommunicationandorbitalresourcesso

astoavoidharmfulinterference.

EMCStandards:EN55022andEN55024(CEmarked)

SafetyStandards:ThisequipmentcomplieswithIEC60950‐1,2NDEdition+Amendment1(CE

marked)andwithUL60950‐1,2NDEdition+Amendment1(FilenumberE174166)(USAand

Canada)

Overview of RF Modules for PRUs

Page 6 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

OVERVIEWOFRFMODULESFORPRUS

Figure1illustratesthePrismRemoteUnit(PRU),whichcontrolsRFemissions,interfaceswith

theFlexWaveHost.

Figure1.Prism Remote Units

ThePRUhasfromonetofourRFModuleslots,dependingonthePRUmodel.Thatis,the

Single‐BayPRUhasoneRFModuleslot,andtheQuad‐BayPRUhasfourRFModuleslots.APRU

cansupportuptofourRFModules.

ThefunctionofthePRURFModulesontheForwardPathisto:

•convertthedigitizedRFtransportedfromtheHosttoAnalogRF

•amplifytheAnalogRFsignal

•providesignalfiltering.

ThefunctionofthePRURFModulesontheReversePathisto:

•converttheAnalogRFfromthehandsettoDigitalRFfortransporttotheHost

•providesignalfiltering.

Single-Bay

Prism Remote Unit

Dual-Bay

Prism Remote Unit

Tri-Bay

Prism Remote Unit

Quad-Bay

Prism Remote Unit

PRU RF Module Types

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 7

EachRFModulecansupportanyofthefollowingDARTcombinations:

•oneClassicDARToroneSingleSuperDART

•twoClassicDARTs

•twoSingleSuperDARTs

•oneDualSuperDART

•oneortwosetsofTxorRxBoards(HDM)

–HDM‐850hasoneset

–HDM‐700hastwosets.

EachRFModulewillhaveuptotwo6‐timeslotDARTsorone12‐timeslotDARTsperRFModule.

TheRFModulesarefieldreplaceable,butcannotbeservicedinthefield.

PRURFModuleTypes

ThePRURFModulesareavailableinthefollowingformats,andasdescribedinthefollowing

sections:

•“PrismRemoteUnitSingle‐andDual‐CardRFModules”onpage8

•“PrismRemoteUnitHDMRFModules”onpage9

•“PrismRemoteUnitDual‐Slot40WRFModules”onpage10.

Overview of RF Modules for PRUs

Page 8 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

PrismRemoteUnitSingle‐andDual‐CardRFModules

Figure2showsexamplesofPRUSingle‐andDual‐SlotRFModules,bothofwhichhavetwo

DARTs.APRUSingle‐andDual‐CardRFModulecomprise:

•oneDART

•oneDuplexerwithoneortwointernalLowNoiseAmplifiers(LNAs)

•oneLinearPowerAmplifier(LPA)

•oneRemoteDARTInterface(RDI)board.

Figure2.Single- and Dual-Slot RF Modules

Dual-Band Dual-Slot RF Module

Single-Slot Dual-Card RF Module

PRU RF Module Types

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 9

PrismRemoteUnitHDMRFModules

PRUHDMRFModules(Figure3)aredesignedfor850Cellfrequencies.Theinitialreleaseofthe

HDMRFModuleisaSingleInputSingleOutput(SISO)Configurationthat

•interfacesoneHostDART—eitherClassicorSuperDART

•supportstwonon‐contiguousRFslicesupto25MHztotalbandwidth—SuperDARTonly

•supportsupto40WRFoutputpower.

Figure3.HDM RF Module

ThecomponentsofaPRUHDMRFModulearedependentonthemoduletype,aslistedinTable3.

Table3.ComponentsofPRUHDMRFModules

RF Module Type DPM LPA Duplexer Rx Card Tx Card

SISO (1) 1 1 1 1 1

MIMO/Dual Band Module

(2)

1 2 2 2 2

(1) 850 20W and 40W only.

(2) 700 MIMO 20W and 850/1900 20W only.

Overview of RF Modules for PRUs

Page 10 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

PrismRemoteUnitDual‐Slot40WRFModules

TheFlexWavePRUDual‐Slot40WRFModule(Figure5)isdesignedforAWSandPCSfrequencies.

ThePrismRemote40WRFModulecomprises:

•oneDART

•twoPowerAmplifiers(PAs)

•oneRemoteDARTInterface(RDI)board.

NOTE: ThismanualdescribeshowtoinstallthePCS1900andAWS2100Non‐DiversityRFModules.

Figure4.Dual-Slot 40W RF Module

SupportedRFModules

Table4.FlexWavePrismRFModulesforPRUsSupportedinthisInstallationGuide

Catalog Number Description

FWP-4210000MOD 6.5W 800 SMR MODULE, NON-DIVERSITY, CLASSIC

FWP-6216000MOD 10W, EGSM 900, NON-DIVERSITY, SGL SD

FWP-6226000MOD 10W, EGSM 900, DIVERSITY, SGL SD

FWP-7416000MOD 20W, GSM 1800, NON-DIVERSITY, SGL SD

FWP-741S000MOD 20W, GSM 1800, NON-DIVERSITY, DL SD

FWP-7426000MOD 20W, GSM 1800, DIVERSITY, SGL SD

Supported RF Modules

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 11

FWP-8410000MOD 20W RF Module, PCS 1900 Non-Diversity Enclosure

FWP-8416000MOD 20W PCS MODULE, NON-DIVERSITY, SGL SD

FWP-841S000MOD 20W RF Module, PCS 1900 12S Enclosure

FWP-8420000MOD 20W RF Module, PCS 1900 Diversity Enclosure

FWP-8426000MOD 20W PCS MODULE, DIVERSITY, SGL SD

FWP-84MT000MOD 20W RF MOD, PCS1900, MIMO

FWP-8810000MOD 40W PCS MODULE, NON-DIVERSITY, CLASSIC (DUAL-SLOT)

FWP-881T000MOD HDM PCS Band 25 SISO 40W

FWP-9416000MOD 20W, UMTS 2100, NON-DIVERSITY, SGL SD

FWP-9416D00MOD 20W 2100 UMTS MODULE, DIV Ready, SGL SD

FWP-941S000MOD 20W, UMTS 2100, NON-DIVERSITY, DL SD

FWP-9426000MOD 20W, UMTS 2100, DIVERSITY, SGL SD

FWP-A410000MOD 20W RF Module, AWS 2100 Non-Diversity Enclosure

FWP-A416000MOD 20W AWS MODULE, NON-DIVERSITY, SGL SD

FWP-A41S000MOD 20W RF Module, AWS 2100 12S Enclosure

FWP-A420000MOD 20W RF Module, AWS 2100 Diversity Enclosure

FWP-A426000MOD 20W AWS MODULE, DIVERSITY, SGL SD

FWP-A4MT000MOD HDM AWS Band 4 MIMO 20W

FWP-A810000MOD 40W AWS MODULE, NON-DIVERSITY, CLASSIC

FWP-A81T000MOD HDM AWS Band 4 SISO 40W

FWP-B410000MOD 20W WIDEBAND CELL MODULE, NON-DIVERSITY, Classic

FWP-B420000MOD 20W WIDEBAND CELL MODULE, DIVERSITY, CLASSIC

FWP-B810100MOD 40W WIDEBAND CELL MODULE, NON-DIVERSITY, (SGL-SLOT)

FWP-C4MT000MOD DUAL 20W 850/1900 RF MODULE, (SGL BAY)

FWP-D210000MOD 6.5W 800/900 ESMR MODULE, NON-DIVERSITY, CLASSIC

FWP-F216000MOD 10W APAC EGSM (885-915) MODULE, SGL SD

FWP-I210000MOD 6.5W APAC iDEN Module, Non-Diversity, Classic (Extended 1 MHz)

FWP-K216000MOD 10W 900 P-GSM Module, Non-Diversity, SGL SD

FWP-K226000MOD 10W 900 P-GSM Module, Diversity, SGL SD

FWP-L416000MOD 20W 700 Lower ABC MODULE, NON-DIVERSITY, SGL SD

FWP-L4MT000MOD DUAL 20W 700 LOWER ABC MODULE, MIMO

FWP-L4MTU4MMOD 20W RF MOD, 700ABC/700UC

FWP-U416000MOD 700 LTE, UPPER C, 20W MODULE, SISO, SGL SD

FWP-U4MT000MOD DUAL 20W 700 UPPER C MODULE, MIMO

FWP-U816100MOD 40W 700 Upper C MODULE, NON-DIVERSITY, SGL SD (SGL-SLOT)

Table4.FlexWavePrismRFModulesforPRUsSupportedinthisInstallationGuide(Cont.)

Catalog Number Description

RF Module Components

Page 12 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

RFMODULECOMPONENTS

Figure5showstypicalRFModulecomponents,usingtheSingle‐SlotRFModuleasanexample.

Figure5.PRU Single-Slot RF Module Components

Figure6showsthecomponentsofanHDMRFModule.

Figure6.HDM RF Module Components

Mounting

latch

Mounting hook

Duplexer Power Amplifier (PA)

DARTs

Duplexers Power Amplifier

Mounting latch

Mounting hook

Tx and Rx Cards

Duplexer and Low Noise Amplifier

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 13

DuplexerandLowNoiseAmplifier

TheRFModuleprovidesthePRUwithaninternalDuplexerthatisoptimizedtoprovidethe

desiredRFband‐passfilteringandin‐bandequipmentisolationbetweenFWDandREVpaths.

TheDuplexerprovidesthefilteringnecessarytothetransmitandreceivepathstoandfromthe

connectedantenna.

TheDuplexerforthePrismRemoteUnitSingle‐andDual‐CardRFModulesandtheDual‐Slot40W

RFModulescontainsuptotwoREVpathLowNoiseAmplifiers(LNAforPRIand/orSECreverse

paths).EachLNAprovidesthePrismreversepathwithnominal30dBREVgainandsystemNFof

5dBperRXpath.

TheDuplexerforanHDMRFModuledoesnothaveaLowNoiseAmplifier.

Duplexersarenotfieldserviceable.

LinearPowerAmplifiers

TheLinearPowerAmplifier(LPA)isahighqualitybroadbandRFamplifierusedforachieving

Prismproduct‐ratedpowerforthePRUTxforwardpathspectrumRF.ThePAsarepass‐band

specific,withthemaximumcompositeTxpowerlevels,and>10dBinstantaneouspeakpower

ratinglistedin:

•Table5forSingle‐Card,Dual‐Card,andHDMRFModules

•Table6onpage14forDual‐Slot40WRFModules.

TheLPAishousedwithintheRFModule,andisnotfieldserviceable.

Table5.LPAMaximumCompositeTxPowerLevelsforSingle‐Card,Dual‐Card,andHDMRFModules

Passband Maximum

dBm

Watts Instantaneous

Bandwidth

(MHz)

AWS 2100 +43 20 45

Cellular 850 +43 20 25

+46 40 25

EGSM 900 +40 10 35

DCS 1800 +42 15.8 75

LTE 700 Lower ABC +43 20 18

+46 40 18

LTE 700 Upper C +43 20 10

+46 40 10

PCS 1900 +43 20 70

PGSM 900 +40 10 25

SMR 800 +38 6.5 18

SMR 900 +38 6.5 5

UMTS 2100 +42 15.8 60

RF Module Components

Page 14 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

NOTE: IndustryCanada20dBPassBandModelNumberFWP‐C4MT000MODCellular

850MHz=26.3MHzandthePCS1900=66.8MHz.

DigitalProcessingModule

TheDigitalProcessingModule(DPM)isfoundonlyintheHDMRFModules.TheDPMprovides

theprimaryprocessingandlogicfunctionsfortheHDMRFModule.Italsoprovidestheprimary

powerinterfacefortheHDMRFModule,andconversionofthenative28Vdcvoltagetolower

voltagesasnecessaryforfunctionality.

TheDPMhasaTransmit(Tx)BoardandaReceive(Rx)Board:

•TxBoard—providesbandspecificfilteringfortheintendedTransmitpath.

•RxBoard—providesbandspecificfilteringfortheintendedReceivepath.

Table6.LPAMaximumCompositeTxPowerLevelsforDual‐Slot40WRFModules

Passband Maximum

dBm

Watts Instantaneous

Bandwidth (MHz)

PCS 1900 +46 40 70

AWS 2100 +46 40 45

Power Cable Connection

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 15

UNDERSTANDINGTHERFMODULECABLES

BeforeyouinstalltheRFModulecables,familiarizeyourselfwiththerulesthatpertaintothese

cables,asdefinedinthefollowingsections.

AlwaysprovidedateachRFModuleshelfarefivecables:

•twoHigh‐SpeedDataCables,whichinthisdocumentarereferredtoasLVDS(Low‐Voltage

DifferentialSignaling)cables

•twoRFCables(TX0/RX0)and(TX1/RX1)

•onePower(PWR)Cable.

PowerCableConnection

Maintainadequatestrainreliefdistancesfromtheconnectionpointstothemodule.

LVDSCableConnections

•LVDScableslabeledPRIMandDIVshouldalwayseitherbeconnectedtoaRFModuleorstrain

relievedtoadjacentcables,asthisprotectsthecableagainstdamagethroughmisplacement.

•AlignandfullyinserttheLVDScableconnectorsintotheirrespectiveconnectorcages.Full

insertionisidentifiedbyanaudibleclick.

•EnsurethetwoLVDScablesarefullyseatedandlatchedintotheirrespectivereceptacleson

theRFModulebylightlypullingoutwardontheconnectors.Iffullyseatedandlockedinto

position,thecableconnectorswillnotslidebackout.

•Maintainadequatestrain‐reliefdistancesfromtheconnectionpointstotheRFModule.

RFCableConnections

TheRFModulecablesthatarepre‐installedinthePRUconnecttothecorrespondingconnectors

ontheRFModule.TheRFModulecablescorrelatetotheantennaconnectorsonthebottomofthe

PRUchassis.

Understanding the RF Module Cables

Page 16 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

RFCableRules

•WheninstallingaDiversity,MIMOorDual‐BandRFModule,bothRFcableslabeledMODN

TX0/RX0andMODNTX1/RX1shallbeconnectedtotheN‐StyleconnectionsoftheRF

Module.

•WheninstallingaNon‐DiversityorSISORFModule:

–TheMODNTX0/RX0cableshallbeconnectedtothesingleavailableN‐StyleRF

ConnectionoftheRFModule.

–TheMODNTX1/RX1cableshallbeconstrainedtotheexistingcablesusingatiewrapor

similarlyacceptedfastenersoitcannotbepinchedorpreventthePRUdoorfromclosing.

DonotcutorattempttootherwiseremovethisRFCable.

•RFcablesarehand‐formable;however,cablesmustadheretoaminimumbendradiusof

1‐inchfromtheoutletoftheintegratedcableguidetotherespectiveN‐StyleRFconnection

ontheRFModule.

RFModuleCablesforSingle‐Card,Dual‐Card,andHDMRFModules

TheRFcableandconnectorlabelsalsocorrespondtotheRFModuleslotsinthePRUchassis,

whereMODAisthebottomslotandMODDisthetopslot.Intheinstallationsteps,theRFcables

andconnectorsarereferredtoasMODNTX0/RX0andasMODNTRX1whereNequalsA,B,C,orD.

ThecablesandconnectorshavecorrespondinglabelsasshowninTable7forSingle‐Card,

Dual‐Card,andHDMRFModules.

Table7.RFAntennaLabelsforSingle‐Card,Dual‐Card,andHDMRFModules—FromTopofChassisDown

RF Module

Cable,

RF Module

Connector,

and Remote

Antenna

Connector

Label

Function

Single-Slot

Remote Unit RF

Module Slot

Designations

Dual-Slot Remote Unit RF Module Slot

Designations

Dual-Bay Tri-Bay Quad-Bay

Mod D

TX0/RX0

Transmit RF power and primary receive

to/from the antenna for RF Module D

MOD D N/A N/A MOD C

Mod D

TX1/RX1

Diversity receive for RF power from the

antenna for RF Module D

Mod C

TX0/RX0

Transmit RF power and primary receive

to/from the antenna for RF Module C

MOD C N/A MOD B

Mod C

TX1/RX1

Diversity receive for RF power from the

antenna for RF Module C

Mod B

TX0/RX0

Transmit RF power and primary receive

to/from the antenna for RF Module B

MOD B MOD A MOD B

Mod B

TX1/RX1

Diversity receive for RF power from the

antenna for RF Module B

Mod A

TX0/RX0

Transmit RF power and primary receive

to/from the antenna for RF Module A

MOD A MOD A MOD A

Mod A

TX1/RX1

Diversity receive for RF power from the

antenna for RF Module A

RF Cable Connections

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 17

RFModuleCablesforDual‐SlotInstallations

ForDual‐Slotinstallations,theRFcablesandconnectorsarelabeledasMODNTX0/RX0andMODN

TX1/RX1,whereNreferstothebottomslotofthedouble‐slotinstallation.Forexample,fora

Dual‐SlotinstallationinaQuad‐Baychassis,theRFcablesandconnectorsarelabeledasMODC

TX0/RX0andMODCTX1/RX1.

ThecablesandconnectorshavecorrespondinglabelsasshowninTable8onpage17for

Dual‐Slot40WRFModules.

Table8.RFAntennaLabelsforDual‐Slot40WRFModules(TopofChassisDown)

RF Module

Cable,

RF Module

Connector,

and Remote

Antenna

Connector

Labels

Function

Slots for 40W RF Modules (a) (b)

Dual-Bay Tri-Bay Quad-Bay

Mod D

TX0/RX0

Transmit RF power and primary receive

to/from the antenna for RF Module D

N/A N/A Slots C and D

Mod D RX1 Diversity receive for RF power from the

antenna for RF Module D

Mod C

TX0/RX0

Transmit RF power and primary receive

to/from the antenna for RF Module C

N/A N/A

Mod C RX1 Diversity receive for RF power from the

antenna for RF Module C

Mod B

TX0/RX0

Transmit RF power and primary receive

to/from the antenna for RF Module B

Slots A and B Slots A and B Slots A and B

Mod B RX1 Diversity receive for RF power from the

antenna for RF Module B

Mod A

TX0/RX0

Transmit RF power and primary receive

to/from the antenna for RF Module A

Mod A RX1 Diversity receive for RF power from the

antenna for RF Module A

(a) N/A indicates that the slot cannot be used for a Dual-Slot 40W RF Module

(b) Install the Dual-Slot 40W RF Module in the lower-most slot in the chassis. If, however, if two Dual-Slot 40W

RF Modules are present, install the 2100 Module in the lower-most slot and the 1900 Module in the

upper-most slot.

Understanding the RF Module Cables

Page 18 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

RFGroupAssignmentsforPRUs

A PRU comprises from one to four RF Module slots. Figure 7 illustrates the

numbering of RF Module slots and DARTs.

Figure 7. DART RF Groups in a Prism Remote Unit (PRU)

Prism Quad-Band Remote Unit with Single-Card RF Modules

SeRF Module

DART 7

DART 8

Group D

DART 5

DART 6

Group C

DART 3

DART 4

Group B

DART 1

DART 2

Group A

RF Group Assignments for PRUs

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 19

Table 9 lists how the FlexWave Prism EMS references the RF group assignments

and corresponding components of each RF Module.

NOTE: In a dual-LPA system, the Configure Remote Forward Gain page shows two values for the LPA

status, one for each LPA. Changing the LPA Mode or resetting the LPA applies to both LPAs at the

same time.

CAUTION! Should your system experience an LPA problem, refer to Table 9 to ensure that you apply new

settings or troubleshoot the correct RF Module.

CAUTION! If you use a customized SNMP polling for system status, you must change your LPA indexing

scheme.

Table 9. Remote Unit RF Group Assignments (from Top/Down)

Physical

RF Slot

Group

DART

Number

LNA Number LPA

Number

for Single

LPA

Number

for Dual

LPAs

Power

Detector

Number

for Single

Power

Detector

Number

for Dual

PDs

Primary Diversity

D D 8 8 7878

7 7 7 7

C C 6 6 5656

5 5 5 5

B B 4 4 3434

3 3 3 3

A A 2 2 1212

1 1 1 1

SeRF Board

Understanding the RF Module Cables

Page 20 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

TheDual‐Slot40WRFModuleoccupiestwoslotsinaPrismRemote.Figure8showsthemain

componentsinaPrismenclosure,witha40WRFModuleoccupyingSlotsAandB.Thecontrolling

DARTwillalwaysbeintheupperslot(BorD),andthesecondLPAisalwaysinthelowerslot(A

orC).

Figure8.Dual-Slot 40W RF Module in a Quad-Bay Prism Remote

NOTE: IfaDual‐Slot40WRFModuleAWS2100andaDual‐Slot40WRFModulePCS1900areboth

installedinaQuad‐BayRemote,itisrecommendedthatthePCS1900beinstalledinupper‐most

slot,andtheAWS2100beinstalledinthelower‐mostslot.

NOTE: Toaccommodatetwo‐slotmodules,youneedtoremoveamoduleslotshelfasdescribedin

“Dual‐SlotModulesOnly—RemovetheModuleSlotShelf”onpage25.

Dual-slot 40W RF Module

in Slot B (upper slot) and

Slot A (lower slot) with the

controlling DART in Slot B

and the second DART in Slot A

AC power switch

Four DC power switches

SeRF Module and Power supplies

Slot C (empty for future use)

Slot D (empty for future use)

Fans

Connectivity panel with Status LED

Safety Precautions

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 21

INSTALLTHERFMODULE(S)

ThefollowingsectionsguideyouthroughtheinstallationofanRFModuleintoaPRUchassis.The

processtoinstallthefourdifferenttypesofRFModulesisbasicallythesame;however,

differencesarenotedandshouldbefollowed.

NOTE: Inthefollowingsteps,theRFcablesandconnectorsarereferredtoasMODNTX0/RX0andas

MODNTRX1whereNequalsA,B,C,orD.

SafetyPrecautions

CAUTION! Thisisrestrictedaccessequipmentandonlyqualifiedservicepersonnelshouldserviceand

operatethisequipmentusingappropriatetools.

CAUTION! Wetconditionsincreasethepotentialforreceivinganelectricalshockwheninstallingorusing

electrically‐poweredequipment.Topreventelectricalshock,neverinstalloruseelectrical

equipmentinawetlocationorduringalightningstorm.

CAUTION! Alwaysallowsufficientfiberlengthtopermitroutingofpatchcordsandpigtailswithoutsevere

bends.Fiberopticpatchcordsorpigtailsmaybepermanentlydamagedifbentorcurvedtoa

radiusoflessthan2inches(5.1cm).

CAUTION! ExteriorsurfacesofthePrismRemoteUnitmaybehot.Usecautionduringservicing.

CAUTION! Servicepersonnelmustconfirmthattheperimetergasketanddoor‐to‐doorgasketsareinplace

whenclosingthePrismdoorsafterservicing.

CAUTION! ThisequipmentusesaClass1LaseraccordingtoFDA/CDRHrules.Laserradiationcanseriously

damagetheretinaoftheeye.Donotlookintotheendsofanyopticalfiber.Donotlookdirectly

intotheopticaltransceiverofanydigitalunitorexposuretolaserradiationmayresult.An

opticalpowermetershouldbeusedtoverifyactivefibers.AprotectivecaporhoodMUSTbe

immediatelyplacedoveranyradiatingtransceiveroropticalfiberconnectortoavoidthe

potentialofdangerousamountsofradiationexposure.Thispracticealsopreventsdirtparticles

fromenteringtheadapterorconnector.

CAUTION! ThissystemisanRFTransmitterandcontinuouslyemitsRFenergy.Maintain3foot(91.4cm)

minimumclearancefromtheantennawhilethesystemisoperating.Whereverpossible,shut

downtheRANbeforeservicingtheantenna.

Install the RF Module(s)

Page 22 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

GuardagainstDamagefromElectro‐StaticDischarge

CAUTION! Electro‐StaticDischarge(ESD)candamageelectroniccomponents.TopreventESDdamage,

alwayswearanESDwriststrapwhenworkingwiththeIRUorwhenhandlinganyofits

components.ConnectthegroundwireontheESDwriststraptoanearthgroundsourcebefore

touchingtheIRUoranyofitscomponents.Wearthewriststraptheentiretimethatyouwork

withtheIRUanditscomponents.

CAUTION! PlacethePrismRFModulesinanti‐staticpackingmaterialwhentransportingorstoringthem.

UnpackandInspecttheRFModule

1Inspecttheexterioroftheshippingcontainer(s)forevidenceofroughhandlingthatmayhave

damagedthecomponentsinthecontainer.

2Unpackeachcontainerwhilecarefullycheckingthecontentsfordamageandverifywiththe

packingslip.

3Ifdamageisfoundorpartsaremissing,fileaclaimwiththecommercialcarrierandnotifyTE

CustomerService(see“ContactingTEConnectivity”onpage46).Savethedamagedcartons

forinspectionbythecarrier.

4Saveallshippingcontainersforuseiftheequipmentrequiresshipmentatafuturedate.

CAUTION! HandletheRFModulewithcareduringinstallation.Beespeciallycarefultonotdamagethe

thermal‐interfacematerial(TIM),whichisattachedtotheLPA.IftheTIMisdamaged,theLPA

canoverheat.BeforeinstallingtheRFModule,checktoseeiftheheatsinkmaterialisgougedor

cracked.IftheTIMisdamaged,donotinstalltheRFModuleandcontactTEConnectivityfor

assistance(see“ContactingTEConnectivity”onpage46forcontactinformation).

CAUTION! Ifthethermal‐interfacematerialisdamaged,theinstallationanduseoftheRFModulemayvoid

thewarrantyoftheRFModule.

Remove Release Liners from the RF Module

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 23

RemoveReleaseLinersfromtheRFModule

NOTE: ReleaseLinersarepresentonfrontandbackofnewmodules.

1OpenthePRUenclosure.

2Removereleaseliners,ifpresent,fromthethermalpadsontheRFModulepriortoinstalling

themoduleintothePRUchassis.

CAUTION! Thethermalpadsareverysensitivetomishandling—donotnick,scratch,ordingthem.

FormostRFModules,thethermalpadsarelocatedaslistedbelowandasshowninFigure9,

whichshowsaDual‐Slot40WRFModule.

•onelargepadonthebacksurfaceofeachLinearPowerAmplifier(LPA)

•uptotwoonthefrontsurface(DARTs)

•oneontheleftsideforthe(RDI)

•oneonthevectormodulatorboard

•oneontheRFpowercombiner.

Figure9.Thermal Pads on a Dual-Slot 40W RF Module

One large

thermal pad on each PA

(bottom of the LPA)

One thermal pad

for the RDI

One thermal pad

for each DART

One thermal pad

for each DART

One thermal pad

for RF Power

Combiner

One thermal pad

for Vector

Modulator

Install the RF Module(s)

Page 24 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

ForHDMRFModules,thethermalpadsarelocatedaslistedbelowandasshowninFigure10.

•onepadforeachRxandTxboard

•onelargepadovertheDPM

•oneforeachPowerAmplifier(PA),whichisonthebottomoftheHDMRFModule.

Figure10.Thermal Pads on an HDM RF Module

DPM Thermal Pad

Tx A Thermal Pad

Tx B Thermal Pad

Rx A Thermal Pad

Rx B Thermal Pad

2.9796 in2.9796 in

NOTE: Tx and Rx cards are paired: Tx A ony pairs with Rx A and Tx B only pairs with Rx B.

Dual-Slot Modules Only—Remove the Module Slot Shelf

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 25

Dual‐SlotModulesOnly—RemovetheModuleSlotShelf

1ForDual‐SlotRFModulesonly.

IfyouareinstallingaDual‐Slot

RFModule,youmustremovea

moduleslotshelffromthePRU

chassistoaccommodatethe

module’ssize.(Forfurther

information,seeTable7on

page16.)

Removetheshelfasappropriate

fortheRFModule:

•ForaDual‐Slot40WRF

Module,removetheModule

BShelf.

•ForaDual‐BayDual‐SlotRF

Module,removeModuleD

Shelf.

Toremovethemoduleshelf:

aUsea9/64”Allen™wrench

toremovethethreescrews

thatattachthemoduleshelf

tothePRUchassis,asshown

inthefollowinggraphic.

bDiscardorstorethemodule

shelfandfasteners.

Use 9/64” Allen Wrench to

remove the three module-shelf screws

Remove Module D Shelf for

Dual-Band Dual-Slot RF Modules

Remove Module B Shelf for

Dual-Slot 40W RF Modules

Install the RF Module(s)

Page 26 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

InstalltheRFModuleintothePrismRemoteChassis

Recommendation: InstallDual‐BayDual‐Slotmodulesinthetwoupper‐mostslotsofthePRU.

Recommendation: InstallDual‐Slot40Wmodulesinthebottom‐mostslotsofthePRU.

Recommendation: IfbothaDual‐SlotAWS210040WRFModuleandaDual‐SlotPCS190040W

RFModuleareinstalledinaQuad‐BayPRU,installtheAWS2100Modulein

thelower‐mostslotofthePRU.

1HoldtheRFModulesothattheDARTcard(s)faceawayfromthePRUandtheMountingHook

istowardtheReceivingflangeonthePRUchassis.

NOTE: AlwaysinstallRFModulesfromthebottomup.Donotskipaslot.

2HoldingtheRFModuleata45°angleinrespecttotherearheatsink,restthebottomsurface

ofthemoduleontheRFModuleshelf,asshowninoneofthefollowinggraphics,andas

applicabletotheRFModule.

•Single‐SlotRFModule:Figure11onpage27

•HDMRFModule:Figure12onpage28

•Dual‐BayDual‐SlotRFModule:Figure13onPage29

•Dual‐Slot40WRFModule:Figure14onPage30.

Install the RF Module into the Prism Remote Chassis

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 27

Figure11.Installing a Single-Slot RF Module

RF MOD C

RF MOD D

SeRF

Module

RF MOD A

RF MOD B

Single-Slot

RF Module

Heat Sink

Install the RF Module(s)

Page 28 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

Figure12.Installing an HDM RF Module

RF MOD C

RF MOD D

SeRF

Module

RF MOD A

RF MOD B

HDM RF Module

Install the RF Module into the Prism Remote Chassis

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 29

Figure13.Installing a Dual-Bay Dual-Slot RF Module

Installing a Dual-Band

Dual-Slot RF Module

Install the RF Module(s)

Page 30 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

Figure14.Installing a Dual-Slot 40W RF Module

Install the RF Module into the Prism Remote Chassis

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 31

3AligntheMountingHookonthemodulewiththereceivingflangeonthePRUheatsink,and

thenslidetheRFModuleintowardtheflangeuntilitcangonofurther.

RF Module

Mounting

hook

Chassis

Receiving

flange

Install the RF Module(s)

Page 32 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

4PushtheleftedgeoftheRFModulebackandintothePRUchassisuntilitcangonofurther,as

showninthefollowinggraphics:

•ForSingle‐SlotRFmodules,seeFigure15onpage32.

•ForHDMRFmodules,seeFigure16onpage33.

•ForDual‐SlotRFmodules,seeFigure17onpage34,whichusestheDual‐Slot40WRF

Moduleasanexample.

CAUTION! MakesuretheRFModuleisseatedcorrectlyintheModuleshelf.IncorrectalignmentoftheRF

ModulecancausetheRFModuletofailduetooverheating.

•ThefrontedgeoftheRFModuleshouldbeparallelwiththeshelfaboveit.

•TheMountingHookontheRFModuleshouldbefullyengagedwiththeReceivingflangeon

thePRUchassis.

•IfyoulatercannotshutthePRUdoor,verifythattheRFModuleisinstalledcorrectly.

Figure15.Seating a Single-Slot RF Module

Push the RF Module

back into the chassis

until it can go no further.

Single-Slot

RF Module

Install the RF Module into the Prism Remote Chassis

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 33

Figure16.Seating an HDM RF Module

Push the HDM RF Module

back into the chassis

until it can go no further.

HDM

RF Module

Install the RF Module(s)

Page 34 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

Figure17.Seating a Dual-Slot RF Module

SecureRFModuleLatches

1TosecurethemodulelatchesontheleftsideoftheRFModule,dooneofthefollowing,as

appropriatefortheRFModulebeinginstalled:

•“ConnectLatchesonSingle‐SlotandHDMRFModules”onpage35

•“ConnectLatchesonDual‐BayDual‐SlotRFModules”onpage36.

Push the RF Module back

into the chassis until it can

go no further.

Secure RF Module Latches

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 35

ConnectLatchesonSingle‐SlotandHDMRFModules

ForSingle‐SlotandHDMRFModules,securetwolatches,asshowninFigure18.

Figure18.Latches on Single-Slot and HDM RF Modules

Two latches on Single-Slot

RF Modules

Two latches on

HDM RF Modules

Install the RF Module(s)

Page 36 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

ConnectLatchesonDual‐BayDual‐SlotRFModules

ForDual‐BayDual‐SlotRFModules,securefourlatches,asshowninFigure19.

Figure19.Dual-Bay Dual-Slot RF Module Latches

Four latches in a

Dual-Band Dual-Slot

RF Module

Connect the RF Module Cables

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 37

LatchesonDual‐Slot40WRFModules

ForDual‐Slot40WRFModules,securefourlatches,asshowninFigure20.

Figure20.Dual-Slot 40W RF Module Latches

VerifythattheRFModuleMountingHookisEngaged

1VerifythattheRFModuleMountingHookisengagedcorrectlybypullingthemoduleaway

fromtheheatsink.TheRFModuleshouldnotmove.IftheRFModulemovesduringthischeck,

repeatallthestepsstartingat“InstalltheRFModuleintothePrismRemoteChassis”on

page26throughthisstep.

ConnecttheRFModuleCables

ThestepstoconnecttheRFModulecableshavebeenseparatedintotwodifferentprocedures;

followthestepsthatcorrespondtotheRFModulebeinginstalled.

•“ConnectingCablesinaSingle‐SlotRFModuleInstallation”onpage38

•“ConnectingCablesinaDual‐SlotRFModuleInstallation”onpage40.

Four latches in

a Dual-Slot 40W

RF Module

Install the RF Module(s)

Page 38 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

ConnectingCablesinaSingle‐SlotRFModuleInstallation

1PositionthecablessothattheyareundertherightedgeoftheRFModule,pointingup.

2Followtheruleslistedin“UnderstandingtheRFModuleCables”onpage15.

3Workingfromthebottomconnectorup,connecttheRFModulecables,asfollows:

aConnecttheMODNTX1/RX1cabletotheRFModule.

iIfaTX1/RX1RFModuleconnectionisavailable,inserttheN‐StylePlugoftheMODN

TX1/RX1cableintotheTX1/RX1N‐StyleJackoftheRFModule.If RF Module

connection is not available, constrain the MOD N TX1/RX1 cable toaccompanying

cablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoorfromclosing.

ii Turnthecouplingnutoftheplugclockwisetothreadontothejackandfinger‐tighten.

iii Torquecouplingnutto8+/‐1in‐lbstoensurefullconnection.

NOTE: InsufficienttorqueappliedtoRFModuleconnectionscanresultinelevatedinsertion/returnloss

andhigherthannormalVSWRreportedbythesystem.

bConnecttheMODNTX0/RX0cabletotheRFModule.

iInserttheN‐StylePlugoftheMODNTX0/RX0cableintotheTX0/RX0N‐StyleJackof

theRFModule.

ii Turnthecouplingnutoftheplugclockwisetothreadontothejackandfinger‐tighten.

iii Torquecouplingnutto8+/‐1in‐lbstoensurefullconnection.

NOTE: InsufficienttorqueappliedtoRFModuleconnectionscanresultinelevatedinsertion/returnloss

andhigherthannormalVSWRreportedbythesystem.

cConnecttheLVDSCablestotheRFModule.

iConnect the MOD N DIV LVDS Cable to the DIV receptacle of the RF Module by

insertingandslidinginuntilfullyseated.

NOTE: AlwaysconnecttheDiversityLVDSCablewiththeRFModule.

ii ConnecttheMODNPRIMLVDSCabletothePRIMconnector,followingthesamesteps

asabove.

NOTE: FullinsertioncanberecognizedbyanaudibleclickastheLVDSCableConnectorlocksintotheRF

ModuleReceptacle.ThiscanbeverifiedbylightlypullingbackontheLVDSconnectorwhile

makingsurenottodepressthereleasetrigger.Whenfullyinserted,thecableshouldnotbeable

toberemovedfromthereceptacle.

dConnectthePowerCableConnectortothePWRreceptacleoftheRFModulebyinserting

andslidinginuntilfullyseated.

NOTE: FullinsertioncanberecognizedbyanaudibleclickasthePowerCableConnectorlocksintothe

RFModuleReceptacle.ThiscanbeverifiedbylightlypullingbackonthePowerCableConnector

whilemakingsurenottodepressthereleasetriggersontheendsoftheconnector.Whenfully

inserted,thecableshouldnotbeabletoberemovedfromthereceptacle.

Connect the RF Module Cables

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 39

RefertothegraphicthatcorrespondstotheRFModulebeinginstalledintoasingleslot(bay)

ofthePRU:

•Single‐SlotRFModule:Figure21onPage39

•HDMRFModule:Figure22onpage40

Figure21.Cable Connections for Single-Slot RF Modules

CAUTION! EnsurethatallcablebendsarebelowthetopedgeoftheConnectorInterfacePanelasindicated

bythedashedlineintheprecedingfigure.Failuretocorrectlypositionthecablescouldinhibit

closingthePRUdoor,whichcanresultindamagetothecables.

MOD A

MOD D

MOD C

MOD B

SeRF

Module

TX0/RX0

RX1

DIV

PRIM

PWR

Note routing of

high-speed cables

Note bend

radii ≥ 1-inch

Edge of Connector Interface Panel

Cable connections for a Single-Slot RF Module

Install the RF Module(s)

Page 40 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

Figure22.Cable Connections for HDM RF Modules

ConnectingCablesinaDual‐SlotRFModuleInstallation

1PositionthecablessothattheyareundertherightedgeoftheRFModule,pointingup.

2Followtheruleslistedin“UnderstandingtheRFModuleCables”onpage15.

3FollowtheruleslistedbelowthatpertainonlytoDual‐SlotRFModules.

•TheupperRFModuleshelfwilleithernotbepresent(factoryinstalledmodule)orwillbe

removedpriortoinstallation(fieldinstalledmodule).

•TheMODNTX0/RX0cableforthelowerRFModuleslotwillneedtobeconnectedtothe

MODNTX0/RX0N‐StyleRFconnectionoftheDual‐SlotRFModule.

•ConstraintheMODNTX1/RX1cabletotheexistingcablesusingatiewrapsuchsoit

cannotbepinchedorpreventthePRUdoorfromclosing.Donotcutorattemptto

otherwiseremovethisRFcable.

•ThePower(PWR)cableandtwoLVDScablesoftheupperRFModuleslotarenotused

wheninstallingaDual‐SlotRFModule.

Cable Connections for an HDM RF Module

TX0/RX0

TX1/RX1

POWER

DATA 1 (DIV)

DATA 0 (PRIM)

Cable Connection Notes

• Always connect the Power cable.

• Always connect the two LVDS cables: PRIM and DIV.

• SISO requires one RF cable (TX1/RX1).

• MIMO and Dual-Band require two RF cables

(TX1/RX1 and TX0/RX0).

Connect the RF Module Cables

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 41

4Workingfromthebottomconnectorup,connecttheRFModulecables,asfollows:

aConnecttheMODNTX1/RX1cabletotheRFModule.

NOTE: DonotremoveanyfactoryconnectedRFCables.

iConstraintheMODNTX1/RX1cableofthelowerRFModuleslottoaccompanying

cablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoorfromclosing.

ii ConnecttheMODNTX1/RX1cabletotheTX1/RX1orN/C,N‐StyleJackoftheupper

RFModuleslot.

iii Turnthecouplingnutoftheplugclockwisetothreadontothejackandfinger‐tighten.

iv Torquecouplingnutto8+/‐1in‐lbstoensurefullconnection.

NOTE: InsufficienttorqueappliedtoRFModuleconnectionscanresultinelevatedinsertion/returnloss

andhigherthannormalVSWRreportedbythesystem.

bConnecttheMODNTX0/RX0cabletotheRFModule.

NOTE: DonotremoveanyfactoryconnectedRFCables.

iIfTX0/RX0RFModuleconnectionisavailable,inserttheN‐StylePlugoftheMODN

TX0/RX0cableintotheTX0/RX0N‐StyleJackofthelowerRFModule slot. If RF

Module connection is not available, constrain the MOD N TX0/RX0cableto

accompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoor

fromclosing.

ii Turnthecouplingnutoftheplugclockwisetothreadontothejackandfinger‐tighten.

iii Torquecouplingnutto8+/‐1in‐lbstoensurefullconnection.

iv IfTX0/RX0RFModuleconnectionisavailable,inserttheN‐StylePlugoftheMODN

TX0/RX0cableintotheTX0/RX0N‐StyleJackoftheupperRFModule slot. If RF

Module connection is not available, constrain the MOD N TX0/RX0cableto

accompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoor

fromclosing.

vTurnthecouplingnutoftheplugclockwisetothreadontothejackandfinger‐tighten.

vi Torquecouplingnutto8+/‐1in‐lbstoensurefullconnection.

NOTE: InsufficienttorqueappliedtoRFModuleconnectionscanresultinelevatedinsertion/returnloss

andhigherthannormalVSWRreportedbythesystem.

Install the RF Module(s)

Page 42 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

cConnecttheLVDSCablestotheRFModule.

iIfavailable,connecttheMODNDIVLVDSCabletotheDIVreceptacleofthelowerRF

Modulebyinsertingandslidinginuntilfullyseated.IfDIVreceptacleisnotavailable,

constraintheMODNDIVLVDSCabletoaccompanyingcablesusingatiewrapsoit

cannotbepinchedorpreventthePRUdoorfromclosing.

ii Ifavailable,connecttheMODNPRIMLVDSCabletothePRIMreceptacleofthelower

RFModulebyinsertingandslidinginuntilfullyseated.IfDIV receptacle is not

available,constraintheNPRIMLVDSCabletoaccompanyingcablesusingatiewrap

soitcannotbepinchedorpreventthePRUdoorfromclosing.

iii Ifavailable,connecttheMODNDIVLVDSCabletotheDIVreceptacleoftheupperRF

Modulebyinsertingandslidinginuntilfullyseated.IfDIVreceptacleisnotavailable,

constraintheMODNDIVLVDSCabletoaccompanyingcablesusingatiewrapsoit

cannotbepinchedorpreventthePRUdoorfromclosing.

iv Ifavailable,connecttheMODNPRIMLVDSCabletothePRIMreceptacleoftheupper

RFModulebyinsertingandslidinginuntilfullyseated.IfDIV receptacle is not

available,constraintheNPRIMLVDSCabletoaccompanyingcablesusingatiewrap

soitcannotbepinchedorpreventthePRUdoorfromclosing.

NOTE: FullinsertioncanberecognizedbyanaudibleclickastheLVDSCableConnectorlocksintotheRF

ModuleReceptacle.ThiscanbeverifiedbylightlypullingbackontheLVDSconnectorwhile

makingsurenottodepressthereleasetrigger.Whenfullyinserted,thecableshouldnotbeable

toberemovedfromthereceptacle.

dConnectthePowercabletotheRFModule.

iConnectthePowerCableConnectortothePWRreceptacleofthelowerRFModuleby

insertingandslidinginuntilfullyseated.

ii Ifavailable,connectthePowerCableConnectortothePWRreceptacleoftheupperRF

Modulebyinsertingandslidinginuntilfullyseated.IfPWRreceptacleisnotavailable,

constrainthePowerCabletoaccompanyingcablesusingatiewrapsoitcannotbe

pinchedorpreventthePRUdoorfromclosing.

NOTE: FullinsertioncanberecognizedbyanaudibleclickasthePowerCableConnectorlocksintothe

RFModuleReceptacle.ThiscanbeverifiedbylightlypullingbackonthePowerCableConnector

whilemakingsurenottodepressthereleasetriggersontheendsoftheconnector.Whenfully

inserted,thecableshouldnotbeabletoberemovedfromthereceptacle.

RefertothegraphicthatcorrespondstotheRFModulebeinginstalledinadual‐slot:

•Dual‐BayDual‐SlotRFModule:Figure23onPage43

•Dual‐Slot40WRFModule:Figure24onPage44.

Connect the RF Module Cables

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 43

Figure23.Cable Connections for Dual-Bay Dual-Slot RF Modules

Cable Connections for a Dual-Slot RF Module

Tie wrap

Factory-installed

RX1 cable

Two N-Type

RF connectors

N-Type

RF connector

Install the RF Module(s)

Page 44 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

Figure24.Cable Connections for Dual-Slot 40W RF Modules

CAUTION! EnsurethatallcablebendsarebelowthetopedgeoftheConnectorInterfacePanelasindicated

bythedashedlineintheprecedingfigure.Failuretocorrectlypositionthecablescouldinhibit

closingthePRUdoor,whichcanresultindamagetothecables.

Tie wrap around

factory-installed

RX1 cable

Keep cable bends

behind the edge

of the Connector

Interface Panel

Power on the RF Module

FlexWave Prism RF Modules for Prism Remote Units Installation Guide Page 45

PowerontheRFModule

1FollowtheruleslistedbelowtotogglethePowerswitchthatcorrespondstotheRFModule

toitsONposition.

•ForDual‐SlotRFModules,usethePowerswitchforthelowermodule.Forexample,to

powerupaDual‐SlotRFModuleincombinedslotsC+DinaQuad‐Baychassis,turnONDC

PowerswitchforModC;leavetheDCPowerswitchforModDOFF.

•ADual‐Slot40WRFModuleusesthePowerSuppliesinbothslots.IftheDual‐Slot40WRF

ModuleisinstalledinslotsC+D,turnONthePowerswitchforModCandModD.

2Repeatallthestepsin“InstalltheRFModule(s)”onpage21toinstallotherRFModules.

MOD A

SeRF

Module

AC Power

switch for

Remote

chassis

DC Power switch for Mod A

DC Power switch for Mod B

DC Power switch for Mod C

DC Power switch for Mod D

MOD B

MOD C

MOD D

Contacting TE Connectivity

Page 46 FlexWave Prism RF Modules for Prism Remote Units Installation Guide

CONTACTINGTECONNECTIVITY

ContactingTEConnectivitybyTelephone

ContactingTEConnectivityOnline

ClickononeofthefollowingURLs,orpast

theURLintoyourwebbrowser.

Sales

Asia Pacific +65-6294-9948

France 0800 914032

Germany 0180 2232923

Italy 0800 782374

Spain 900 983291

United Kingdom 0800 960236

USA or Canada 1-800-366-3891

Extension 73000

Connectivity Extension 73475

Wireless Extension 73476

Technical Support

USA or Canada 1-800-530-9960

Elsewhere +1-952-917-0761

Customer Portal

https://www.te.com/portal/wireless/

Technical Support for Wireless Products

http://www.te.com/WirelessSupport

ADC Telecommunications PSM7A7UD FlexWave Prism HDM 700 Lower ABC/Upper C User Manual RF modules installation guide

ADC Telecommunications Inc FlexWave Prism HDM 700 Lower ABC/Upper C RF modules installation guide

RF modules installation guide

Navigation menu

Namespaces

Views

Navigation