ADC ACE COM L1 ThinMux Chassis User Manual To The 871fc9a0 4414 4e9f 8126 Eee2e1cdb7e2
User Manual: ADC ACE-COM L1 to the manual
Open the PDF directly: View PDF 
.
Page Count: 34
| Download | |
| Open PDF In Browser | View PDF |
USER MANUAL ThinMux Chassis Product Catalog: ACE-COM L1 Part Number: 150-2263-01 CLEI: VAMXHN0F LTPH-UM-1088-02, Issue 2 Revision History of Manual To order copies of this document, use document catalog number LTPH-UM-1088-02. Issue Release Date Revisions Made 1 June 22, 2001 Initial release. 2 January 3, 2002 Update to reflect install, wiring, and setup only. Copyright January 3, 2002 © 2002 ADC DSL Systems, Inc. All rights reserved. Trademark Information ADC is a registered trademark of ADC Telecommunications, Inc. No right, license, or interest to such trademarks is granted hereunder, and you agree that no such right, license, or interest shall be asserted by you with respect to such trademark. Other product names mentioned in this practice are used for identification purposes only and may be trademarks or registered trademarks of their respective companies. Disclaimer of Liability Information contained in this document is company private to ADC DSL Systems, Inc., and shall not be modified, used, copied, reproduced or disclosed in whole or in part without the written consent of ADC. Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice. In no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits, and ADC further disclaims any and all liability for indirect, incidental, special, consequential or other similar damages. This disclaimer of liability applies to all products, publications and services during and after the warranty period. similar damages. This disclaimer of liability applies to all products, publications and services during and after the warranty period. ii January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 Using This Manual USING THIS MANUAL The following conventions are used in this manual: • Monospace type indicates screen text. • Keys you press are indicated by small icons such as Y or ENTER . Key combinations to be pressed simultaneously are indicated with a plus sign as follows: CTRL + ESC . • Items you select are in bold. Three types of messages, identified by icons, appear in text. Notes contain information about special circumstances. Cautions indicate the possibility of personal injury or equipment damage. The Electrostatic Discharge (ESD) symbol indicates that a device or assembly is susceptible to damage from electrostatic discharge. UNPACK AND INSPECT YOUR SHIPMENT Upon receipt of the equipment: • Unpack each container and inspect the contents for signs of damage. If the equipment has been damaged in transit, immediately report the extent of damage to the transportation company and to ADC. Order replacement equipment, if necessary. • Check the packing list to ensure complete and accurate shipment of each listed item. If the shipment is short or irregular, contact ADC as described in “Appendix C - Product Support” on page 19. If you must store the equipment for a prolonged period, store the equipment in its original container. ThinMux Chassis January 3, 2002 iii Safety Warnings and Notices LTPH-UM-1088-02, Issue 2 SAFETY WARNINGS AND NOTICES The ThinMux chassis DC power supply feeds must be connected to either (1) -48 Vdc Safety Extra Low Voltage (SELV) sources or (2) -48 Vdc sources that are electrically isolated from the AC sector and reliably connected to earth. The source’s fault current capacity shall be lower than 50A, or an appropriate overcurrent protection rated 5A, must be provided on each -48 Vdc conductor. The overcurrent protection can also be used as a cutoff switch if another disconnect device is not installed. This equipment may be provided with a module that incorporates laser source(s). Refer to the module’s documentation for detailed safety information. The telemetry I/O must be connected to either a SELV source or an ELV source that is electrically isolated from the AC sector and reliably connected to earth. The metallic telecommunication interface should not leave the building premises unless connected to telecommunication devices providing primary and secondary protection. iv January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 Table of Contents TABLE OF CONTENTS Overview ________________________________________________ 1 Features ............................................................................................ 1 Backplane......................................................................................... 2 External Interfaces ________________________________________ 3 T1/E1 Interface ................................................................................ 3 T1/E1 Test Interface......................................................................... 3 RS-232 Craft Interface ..................................................................... 4 10/100BASE-T Ethernet Interface................................................... 4 Discrete Alarms................................................................................ 4 Battery Supply.................................................................................. 5 Installation ______________________________________________ 5 Mounting the Chassis....................................................................... 6 Installing the Fan Module (FB1)...................................................... 7 Wiring the Common Access Panel .................................................. 8 Connect a BITS Timing Source............................................. 8 Connect Test Access .............................................................. 9 Connect Alarms ................................................................... 10 Connecting Power .......................................................................... 10 Installing DS3 or STS-1 Interface Cables...................................... 11 Appendix A - Pin Assignments _____________________________ 14 T1/E1 Interface .............................................................................. 14 RS-232 Craft Interface ................................................................... 17 10/100BASE-T Ethernet Interface................................................. 17 Appendix B - Specifications________________________________ 18 Appendix C - Product Support _____________________________ 19 ThinMux Chassis January 3, 2002 v List of Figures LTPH-UM-1088-02, Issue 2 Appendix D - Abbreviations ________________________________20 Certification and Warranty __________________ Inside Back Cover LIST OF FIGURES 1. Backplane Interfaces (rear view) ...........................................................2 2. ThinMux Chassis in a CO Rack ............................................................6 3. Installing the Fan Module (FB1) ...........................................................7 4. Wire-Wrap Pin Positions/Common Access Panel (rear view) ..............8 5. Installing Line Terminators ...................................................................9 6. Battery Supply Connector (rear view).................................................10 7. DS3 or STS-1 Shelf Configuration......................................................12 8. Male Cable Connector Into Female Backplane Connector .................14 LIST OF TABLES 1. T1/E1 Receive Pin Assignments .........................................................14 2. T1/E1 Transmit Pin Assignments........................................................16 3. RS-232 Craft Interface Pin Assignments.............................................17 4. Ethernet 10/100BASE-T Pin Assignments..........................................17 vi January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 List of Figures LIST OF FIGURES 1. Backplane Interfaces (rear view) .......................................................... 2 2. ThinMux Chassis in a CO Rack............................................................ 6 3. Installing the Fan Module (FB1)........................................................... 7 4. Wire-Wrap Pin Positions/Common Access Panel (rear view).............. 8 5. Installing Line Terminators................................................................... 9 6. Battery Supply Connector (rear view) ................................................ 10 7. DS3 or STS-1 Shelf Configuration ..................................................... 12 8. Male Cable Connector Into Female Backplane Connector................. 14 LIST OF TABLES 1. T1/E1 Receive Pin Assignments......................................................... 14 2. T1/E1 Transmit Pin Assignments ....................................................... 16 3. RS-232 Craft Interface Pin Assignments ............................................ 17 4. Ethernet 10/100BASE-T Pin Assignments ......................................... 17 ThinMux Chassis December 7, 2001 vii List of Tables viii LTPH-UM-1088-02, Issue 2 December 7, 2001 ThinMux Chassis LTPH-UM-1088-02, Issue 2 List of Tables LIST OF TABLES 1. T1/E1 Receive Pin Assignments......................................................... 14 2. T1/E1 Transmit Pin Assignments ....................................................... 16 3. RS-232 Craft Interface Pin Assignments ............................................ 17 4. Ethernet 10/100BASE-T Pin Assignments ......................................... 17 ThinMUX Chassis November 7, 2001 ix List of Tables x LTPH-UM-1088-02, Issue 2 November 7, 2001 ThinMUX Chassis LTPH-UM-1088-02, Issue 2 Overview OVERVIEW The ADC® ThinMux™ chassis houses the ThinMux DS3 or ThinMux STS-1 multiplexer and fits in a Central Office (CO) rack. Each type of multiplexer provides support for a minimum of 28 T1 (or 21 E1) lines from the chassis. The chassis also provides two DS3 interfaces for external equipment. It features a forced-air cooling unit, Ethernet port, rear craft port, craft ports on the multiplexer front panels, and fiber management guides. Offering a 1+1 protected multiplexing function on the network and client side, the ThinMux chassis is the industry’s most compact multiplexer platform. FEATURES • The ThinMux chassis allows for the following shelf configurations: – STS-1 to 28 T1 (using ThinMux multiplexer HXU-359) – DS3 to 28 T1 or 21 E1 lines (using ThinMux multiplexer HXU-360) • Dual multiplexer support for 1+1 protection of network and customer interfaces • Migration path and investment protection on installed equipment • Concentration of many low-speed access network interfaces to a single high-speed network interface • Industry-standard 64-pin T1 (or E1) connectors enable rapid installation • Craft port access for easy configuration • Field-serviceable forced-air cooling unit Depending on your network interface requirements, several cabling options are available. Select the instructions that apply to your configuration as shown in “Installing DS3 or STS-1 Interface Cables” on page 11. ThinMux Chassis January 3, 2002 1 Overview LTPH-UM-1088-02, Issue 2 BACKPLANE RJ-45 Ethernet 10/100BASE-T connector DS3 or STS-1 connectors Line 2 Tx Line 1 Rx Tx DB-9 craft port connector -48 Vdc battery supply screw connectors (common access panel) Rx Bits Test Access CRIT VIS CRIT AUD NO Alarm B- TTIP NO B+ TRING COM A- RTIP NC NC MAJ A+ RRING Frame GND Frame GND CRIT COM FE MIN COM RTN B] -48 B RTN A -48 A FGND Craft RS-232 Chassis ground 32-pair (female) connectors - T1, E1 (left Rx, right Tx) ESD strap input Figure 1. BITS A and B, test access (visual, audible, and discrete alarm wire-wrap pins) Backplane Interfaces (rear view) The ThinMux chassis provides a compact 1U platform for the ThinMux family of multiplexers with the following interconnects: 2 • One 10/100BASE-T Ethernet (IEEE 802.3) • Two 64-pin female receptacle connectors for T1/E1 transmit/receive, chassis-shielded • Four 75Ω BNC connectors for DS3/STS-1 transmit/receive • Four wire-wrap 0.045-inch pins for Building Integrated Timing Supply (BITS) A and B • Four wire-wrap 0.045-inch pins for T1 or E1 test access, transmit/receive • Four wire-wrap 0.045-inch pins for Visible (VIS) and Audible (AUD) alarms (dry relay contacts) which are normally open (NO) discrete alarms • Five wire-wrap 0.045-inch pins for discrete alarms (solid sate relay contacts): Far End, Minor, Major, and Critical • Five screw connectors for -48V dual power • One DB-9 connector for RS-232 communication January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 External Interfaces EXTERNAL INTERFACES The ThinMux chassis provides the following interfaces: • T1/E1 • T1/E1 Test • RS-232 • 10/100BASE-T Ethernet • Discrete alarms T1/E1 INTERFACE There are two female 32-pair connectors to access 28 T1 (or 21 E1) lines for intra-building connection; no protection is provided on the backplane. One connector is for transmission, the other is for reception. Each port is routed to both multiplexers (A and B) for transmit and receive. See “Appendix A - Pin Assignments” on page 14 for interface pinout description. A shielded 32-pair cable should be used and grounded at either the frame or chassis. The ground connection is done at one end of the cable only to avoid ground loops. T1/E1 TEST INTERFACE The four-wire test interface can be routed to any of the 28 T1 (or 21 E1) low-speed T1/E1 ports. It can be used to monitor the line or to look toward the network or subscriber drop. The four signals are accessed through four 0.045-inch wire-wrap pins. (For more information about the wire-wrap pins, see “Connect Test Access” on page 9.) ThinMux Chassis January 3, 2002 3 External Interfaces LTPH-UM-1088-02, Issue 2 RS-232 CRAFT INTERFACE Communication with the ThinMux STS-1 and ThinMux DS3 central processors occur through a standard grounded DB-9 connector (RS-232 Data Communication Equipment interface). Signals are routed to both multiplexers, and the transmitter of the inactive multiplexer remains in a tristate mode. Pin 5 is the digital ground of all digital components (both multiplexers). See Table 3 on page 17 for interface pinout description. 10/100BASE-T ETHERNET INTERFACE Communication with the multiplexer (STS-1 or DS3) central processors occurs through the standard grounded RJ-45 10/100BASE-T interface for metallic chassis. Similar to the RS-232 interface, signals are routed to both multiplexers; the transmitter of the inactive multiplexer remains in a tristate mode. See Table 4 on page 17 for interface pinout description. DISCRETE ALARMS In addition to the various interfaces supplied by the ThinMux chassis, the common access panel (see Figure 4 on page 8) provides access for discrete alarm wiring. The discrete alarms connection is provided by 0.045-inch wire-wrap pins located on the rear of the chassis (see Figure 1 on page 2). The signals are routed to the multiplexers, where the logic functions are performed. Critical VIS and AUD alarms comprise dry contacts for telemetry applications. The alarms have an independent common connection (serial COM port) to relays; normally open (NO) is provided. Current is limited to 0.5A when a maximum temperature rise of 20°C on traces is desired (as per MIL-STD-275C). When using a legacy HXU-358 multiplexer, the CRIT VIS, CRIT AUD, and Alarm pins must be left unconnected. For all other multiplexers, these pins may be used as needed. Other alarms (FE, MIN, MAJ, and CRIT) share the same COM, and only normally open contact is provided as shown in Figure 4 on page 8. Contact closure is made using a solid-state relay photo Metal-Oxide Semiconductor 4 January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 Installation Field-Effect Transistor (MOSFET). When set to ON, resistance is 35Ω at 85°C (worst case). The switched current must be less than 80 mA, and the switched voltage must be less than 135V. If a coil relay or other inductive load is used, a protection diode must be connected between the alarm signal and the COM signal to prevent damage to the solid state relay. ADC does not provide the diode with the ThinMux chassis. The diode must be purchased separately. Use Motorola diode part number 1N4004 or equivalent. BATTERY SUPPLY The battery supply terminals are located on the rear of the chassis under the common access panel (see Figure 1 on page 2). Five AWG 16 wires connect the Return B, -48B, Return A, -48A, and Frame Ground to the power source. To wire power A and B inputs, attach A and B power leads from the fuse panel or office battery to the appropriate screw connector on the terminal block. For more information, refer to “Connecting Power” on page 10. INSTALLATION Before installing the ThinMux Chassis, visually check its packaging to ensure that it has sustained no shipping damage. Immediately report any damage to the shipping agent. See “Appendix C - Product Support” on page 19. ThinMux Chassis January 3, 2002 5 Installation LTPH-UM-1088-02, Issue 2 MOUNTING THE CHASSIS Three 8-32 x 5 /16 screws CO rack Two 6-32 x 1/4 screws Mounting brackets ESD input bracket Two 12-24 x 1/ 2 screws Two 12-24 x 1/2 screws Figure 2. 1 Three 8-32 x 5/16 screws ThinMux Chassis in a CO Rack Install a mounting bracket on each side of the ThinMux chassis using the three screws provided for each bracket (8-32 x 5/16 screws) as shown in Figure 2. (Mounting brackets and screws are contained in the installation kit.) Two sets of mounting brackets are supplied to fit 19-inch or 23-inch racks with standard EIA-hole spacing (1/2 inch). Optional brackets with WECO-hole spacing (1 inch) are available (ACE-MK1). 6 2 Install ESD input bracket on front left side of the chassis. 3 Align the chassis mounting bracket holes with the rack’s vertical mounting holes. Mount the chassis in the rack. Install two 12-24 x 1/2 screws in each bracket and secure the chassis to the rack. January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 Installation INSTALLING THE FAN MODULE (FB1) Fan module ThinMux chassis Figure 3. Installing the Fan Module (FB1) 1 Unwrap the enclosed fan module. 2 Align the fan with the slot located on the left side of the chassis and slide the fan in as shown in Figure 3. 3 Insert the fan module until the connector is firmly seated in the backplane. ThinMux Chassis January 3, 2002 7 Installation LTPH-UM-1088-02, Issue 2 WIRING THE COMMON ACCESS PANEL 1 Unscrew the common access panel hold-down lugs and remove the cover (see Figure 4). CRIT VIS CRIT AUD TTIP NO NO FE B+ TRING COM COM MIN A- RTIP NU NU MAJ A+ RRING Frame GND Frame GND CRIT Bits Test Access B- Alarm COM Figure 4. Wire-Wrap Pin Positions/Common Access Panel (rear view) Connect a BITS Timing Source 2 Determine if you require a BITS timing source connection to the chassis; if so, the chassis must first have a line termination prior to chassis connection. The BITS concept is used for interoffice synchronization distribution. Each line source, Bits A and Bits B, must be terminated. ADC provides this termination through external termination blocks (product catalog TERM-100) placed on wire-wrap terminal posts on the rear of the ThinMux chassis as shown in Figure 5 on page 9. 8 January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 Installation Bits B- B+ Test Access TTIP TRING CRIT VIS NO COM CRIT AUD NO COM Alarm FE MIN A- RTIP NC NC MAJ A+ RRING Frame GND Frame GND CRIT COM RTN B] -48 B RTN A -48 A FGND Craft RS-232 Termination blocks (TERM-100 part number 1178533) Side view of termination block* JP7 Wire-wrap pin B- JP12 B+ Terminator PCB Terminator resistor Chassis backplane AA+ *Install the 100Ω termination block with the resistor facing towards the backplane. Figure 5. Installing Line Terminators 3 Install the BITS terminating blocks (catalog number TERM-100), provided in the installation kit, between the Bits A+, A- and B+, B- posts. 4 Connect Bits A and Bits B posts to your Synchronous Optical Network (SONET) clock synchronization source (SONET minimum clock or better). Use a frame ground post as a shield, if needed. Connect Test Access 5 Connect the Test Access TTIP, TRING, RTIP, RING, and Frame GND posts to the external test head. ThinMux Chassis January 3, 2002 9 Installation LTPH-UM-1088-02, Issue 2 Connect Alarms 6 Connect the alarm relay wires from the CO alarm center to the posts of the Visible Alarm (CRIT. VIS—NO and COM), Audible Alarm (CRIT. AUD—NO and COM) and Alarm (FE, MIN, MAJ, CRIT, and COM). Follow the CO site instructions for connecting alarm relays. The visible and audible alarm relays do not have an NC (normally closed) position. 7 Connect a 16 AWG chassis ground cable to the ground (GND) post. CONNECTING POWER The fuse rating for the ThinMux chassis is 2A. RTN B -48 B RTN A -48 A FGND Figure 6. 10 Battery Supply Connector (rear view) 1 Connect 16 AWG cables to the -48V A, B, and RTN terminals. 2 Connect the other end of the cables to CO battery supply and RTN terminals. 3 Apply power and check the voltage. 4 Reinstall the common access panel and screw in the hold-down lugs. January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 Installation The ThinMux chassis DC power supply feeds must be connected to either (1) -48 Vdc Safety Extra Low Voltage (SELV) sources or (2) -48 Vdc sources that are electrically isolated from the AC sector and reliably connected to earth. The source’s fault current capacity shall be lower than 50A, or an appropriate overcurrent protection, rated 5A, must be provided on each -48 Vdc conductor. The overcurrent protection can also be used as a cutoff switch if another disconnect device is not installed. The ThinMux chassis is configured for redundant power. The A and B battery sources are independently connected to each multiplexer. In the event of a loss of power from one of the sources, an alarm is reported by the active multiplexer. Power is continually supplied to both slots in the chassis. INSTALLING DS3 OR STS-1 INTERFACE CABLES After mounting the chassis to the CO rack, select the appropriate interface for cable installation. (For information regarding multiplexer configuration and operation, refer to the specific multiplexer user manual.) When installing components, wear an antistatic wrist strap. Avoid touching components on the circuit board. ThinMux Chassis January 3, 2002 11 Installation LTPH-UM-1088-02, Issue 2 ESD strap input Chassis ground Line 2 Ethernet 10/100BASE-T Line 1 Common access panel Craft port Tx Rx Tx Rx Bits B- B+ Test Access TTIP TRING CRIT VIS NO COM CRIT AUD NO COM Alarm FE MIN A- RTIP NC NC MAJ A+ RRING Frame GND Frame GND CRIT COM RTN B] -48 B RTN A -48 A FGND Craft RS-232 Alarms, power, and frame ground DSX-1 input (receive) from cross-connect DS3 or STS-1 (In) DS3 or STS-1 (Out) Figure 7. DSX-1 output (transmit) to cross-connect DS3 or STS-1 Shelf Configuration 1 Connect the 32-pair shielded cable, with amphenol male connector coming from the cross-connect, to the DSX-1 input (Rx) as shown in Figure 7. 2 Connect the 32-pair shielded cable, with amphenol male connector going to the cross-connect, to the DSX-1 output (Tx). The metallic telecommunication interface should not be routed from the building premises unless connected to telecommunication devices providing primary and secondary protection. 3 12 Connect the DS3/STS-1 coaxial cable for data coming from the DS3/STS-1 network to Line 1 Rx. January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 Installation 4 Connect the DS3/STS-1 coaxial cable for data going to the DS3/STS-1 network to Line 1 Tx. 5 Connect the Ethernet port to a LAN, if required. 6 Connect a VT100 maintenance terminal to the craft port, if required. ThinMux Chassis January 3, 2002 13 Appendix A - Pin Assignments LTPH-UM-1088-02, Issue 2 APPENDIX A - PIN ASSIGNMENTS T1/E1 INTERFACE Figure 8 shows the male T1/E1 amphenol cable connector connecting to the female T1/E1 connector located on the backplane of the ThinMux chassis. Table 1 on page 14 and Table 2 on page 16 describe the pin assignments for transmit and receive. Figure 8. Male Cable Connector Into Female Backplane Connector Table 1. T1/E1 Receive Pin Assignments Pin Number Description Pin Number Description 1 DSX_RX_RING1 33 DSX_RX_TIP1 2 DSX_RX_RING2 34 DSX_RX_TIP2 3 DSX_RX_RING3 35 DSX_RX_TIP3 4 DSX_RX_RING4 36 DSX_RX_TIP4 5 DSX_RX_RING5 37 DSX_RX_TIP5 6 DSX_RX_RING6 38 DSX_RX_TIP6 Continued 14 January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 Table 1. Appendix A - Pin Assignments T1/E1 Receive Pin Assignments (Continued) Pin Number Description Pin Number Description 7 DSX_RX_RING7 39 DSX_RX_TIP7 8 DSX_RX_RING8 40 DSX_RX_TIP8 9 DSX_RX_RING9 41 DSX_RX_TIP9 10 DSX_RX_RING10 42 DSX_RX_TIP10 11 DSX_RX_RING11 43 DSX_RX_TIP11 12 DSX_RX_RING12 44 DSX_RX_TIP12 13 DSX_RX_RING13 45 DSX_RX_TIP13 14 DSX_RX_RING14 46 DSX_RX_TIP14 15 DSX_RX_RING15 47 DSX_RX_TIP15 16 DSX_RX_RING16 48 DSX_RX_TIP16 17 DSX_RX_RING17 49 DSX_RX_TIP17 18 DSX_RX_RING18 50 DSX_RX_TIP18 19 DSX_RX_RING19 51 DSX_RX_TIP19 20 DSX_RX_RING20 52 DSX_RX_TIP20 21 DSX_RX_RING21 53 DSX_RX_TIP21 22 DSX_RX_RING22 54 DSX_RX_TIP22 23 DSX_RX_RING23 55 DSX_RX_TIP23 24 DSX_RX_RING24 56 DSX_RX_TIP24 25 DSX_RX_RING25 57 DSX_RX_TIP25 26 DSX_RX_RING26 58 DSX_RX_TIP26 27 DSX_RX_RING27 59 DSX_RX_TIP27 28 DSX_RX_RING28 60 DSX_RX_TIP28 29 N/C 61 N/C 30 N/C 62 N/C 31 N/C 63 N/C 32 N/C 64 Chassis Ground ThinMux Chassis January 3, 2002 15 Appendix A - Pin Assignments LTPH-UM-1088-02, Issue 2 Table 2. 16 T1/E1 Transmit Pin Assignments Pin Number Description Pin Number Description 1 DSX_TX_RING1 33 DSX_TX_TIP1 2 DSX_TX_RING2 34 DSX_TX_TIP2 3 DSX_TX_RING3 35 DSX_TX_TIP3 4 DSX_TX_RING4 36 DSX_TX_TIP4 5 DSX_TX_RING5 37 DSX_TX_TIP5 6 DSX_TX_RING6 38 DSX_TX_TIP6 7 DSX_TX_RING7 39 DSX_TX_TIP7 8 DSX_TX_RING8 40 DSX_TX_TIP8 9 DSX_TX_RING9 41 DSX_TX_TIP9 10 DSX_TX_RING10 42 DSX_TX_TIP10 11 DSX_TX_RING11 43 DSX_TX_TIP11 12 DSX_TX_RING12 44 DSX_TX_TIP12 13 DSX_TX_RING13 45 DSX_TX_TIP13 14 DSX_TX_RING14 46 DSX_TX_TIP14 15 DSX_TX_RING15 47 DSX_TX_TIP15 16 DSX_TX_RING16 48 DSX_TX_TIP16 17 DSX_TX_RING17 49 DSX_TX_TIP17 18 DSX_TX_RING18 50 DSX_TX_TIP18 19 DSX_TX_RING19 50 DSX_TX_TIP19 20 DSX_TX_RING20 52 DSX_TX_TIP20 21 DSX_TX_RING21 53 DSX_TX_TIP21 22 DSX_TX_RING22 54 DSX_TX_TIP22 23 DSX_TX_RING23 55 DSX_TX_TIP23 24 DSX_TX_RING24 56 DSX_TX_TIP24 25 DSX_TX_RING25 57 DSX_TX_TIP25 26 DSX_TX_RING26 58 DSX_TX_TIP26 27 DSX_TX_RING27 59 DSX_TX_TIP27 28 DSX_TX_RING28 60 DSX_TX_TIP28 29 N/C 61 N/C 30 N/C 62 N/C 31 N/C 63 N/C 32 N/C 64 Chassis Ground January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 Appendix A - Pin Assignments RS-232 CRAFT INTERFACE Table 3. RS-232 Craft Interface Pin Assignments Pin Number Description 1 NC 2 TX 3 RX 4 DSR 5 Digital ground 6 DTR 7 NC 8 NC 9 NC 10/100BASE-T ETHERNET INTERFACE Table 4. ThinMux Chassis Ethernet 10/100BASE-T Pin Assignments Pin Number Description 1 DATA_TRANSMIT+ 2 DATA_TRANSMIT- 3 DATA_RECEIVE+ 4 NC 5 NC 6 DATA_RECEIVE- 7 NC 8 NC January 3, 2002 17 Appendix B - Specifications LTPH-UM-1088-02, Issue 2 APPENDIX B - SPECIFICATIONS Power Input Voltage Range -60 Vdc to -42.5 Vdc Fusing 2A Environmental Operating temperature -40°F to +149°F (-40°C to +65°C) Operating humidity 10% to 95%, non-condensing Dimensions Height: 1.75 in. Width: 17.35 in. Depth: 12.0 in. Weight: < 10 lbs. (fully configured) Network Interfaces DS3 and STS-1 (using a ThinMux multiplexer) Rear Panel Interfaces DS3/STS-1 18 4 BNC, male DS1/E1 32-pair shielded cable with amphenol male connector Craft DB-9 female Ethernet/Telnet RJ-45 Alarm Contacts Wire-wrap pins, FE, MIN, MAJ, CRIT, COM (NO) Audible Alarm Wire-wrap pins, COM (NO) Visible Alarm Wire-wrap pins, COM (NO) Test Access Wire-wrap pins, TTIP, TRING, RTIP, RRING, Frame GND Power Dual screw terminals Bits A and B Wire-wrap pins A+, A-, B+, B-, shield, RtipA, RringA, RtipB, RringB, shield January 3, 2002 ThinMux Chassis LTPH-UM-1088-02, Issue 2 Appendix C - Product Support APPENDIX C - PRODUCT SUPPORT ADC Customer Service Group provides expert pre-sales and post-sales support and training for all its products. Technical support is available 24 hours a day, 7 days a week by contacting the ADC Technical Assistance Center (TAC). Sales Assistance 800.366.3891 ext. 73000 (USA and Canada) or 952.917.3000 Fax: 952.917.3237 • Quotation Proposals Systems Integration 800.366.3891, ext. 73000 (USA and Canada) or 952.917.3000 • Complete Solutions (from concept to installation) • Ordering and Delivery • General Product Information • Network Design and Integration Testing • System Turn-Up and Testing • Network Monitoring (upstream or downstream) • Power Monitoring and Remote Surveillance • Service/Maintenance Agreements BIA Technical Assistance Center 800.638.0031 or 714.730.3222 Fax: 714.730.2400 Email: wsd_support@adc.com • Systems Operation • Technical Information • System/Network Configuration • Product Specification and Application • Training (product-specific) • Installation and Operation Assistance Online Technical Support • Troubleshooting and Repair/Field Assistance • www.adc.com/Knowledge_Base/index.jsp Online Technical Publications • www.adc.com/library1/ Product Return Department 800.366.3891 ext. 73748 (USA and Canada) or 952.917.3748 Fax: 952.917.3237 Email: repair&return@adc.com • ADC Return Material Authorization (RMA) number and instructions must be obtained before returning products. All 800 lines are toll-free in the USA and Canada. ThinMux Chassis January 3, 2002 19 Appendix D - Abbreviations LTPH-UM-1088-02, Issue 2 APPENDIX D - ABBREVIATIONS A AWG: M American Wire Gauge B BITS: Building Integrated Timing Supply BNC: Bayonet-Locking Connector MAJ: Major Alarm MIN: Minor Alarm MOSFET: Metal-Oxide Semiconductor Field-Effect Transistor N NO: Normally Open C R CO: Central Office COM: Communications Port on a PC (serial port) CRIT: Critical Alarm RX: Receive S D DCE: Data Communication Equipment DS3: Digital Signal, Level 3 SELV: Safety Extra Low Voltage STS: Synchronous Transport Signal, Level 1 T TX: Transmit E ELV: Extra Low Voltage ESD: Electrostatic Discharge F FE: Far End L LAN: 20 Local Area Network January 3, 2002 ThinMux Chassis CERTIFICATION AND WARRANTY FCC CLASS A COMPLIANCE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. LIMITED WARRANTY ADC DSL Systems, Incorporated (“ADC”) warrants that, for a period of sixty (60) months from the date of shipment, the hardware portion of its products will be free of material defects and faulty workmanship under normal use. ADC's obligation, under this warranty, is limited to replacing or repairing, at ADC's option, any such hardware product which is returned during the 60-month warranty period per ADC's instructions and which product is confirmed by ADC not to comply with the foregoing warranty. ADC warrants that, for a period of 90 days from the date of purchase, the software furnished with its products will operate substantially in accordance with the ADC published specifications and documentation for such software. ADC’s entire liability for software that does not comply with the foregoing warranty and is reported to ADC during the 90-day warranty period is, at ADC’s option, either (a) return of the price paid or (b) repair or replace of the software. ADC also warrants that, for a period of thirty (30) days from the date of purchase, the media on which software is stored will be free from material defects under normal use. ADC will replace defective media at no charge if it is returned to ADC during the 30-day warranty period along with proof of the date of shipment. The transportation charges for shipment of returned products to ADC will be prepaid by the Buyer. ADC will pay transportation charges for shipment of replacement products to Buyer, unless no trouble is found (NTF), in which case the Buyer will pay transportation charges. ADC may use reconditioned parts for such repair or replacement. This warranty does not apply to any product which has been repaired, worked upon, or altered by persons not authorized by ADC or in ADC's sole judgment has been subjected to misuse, accident, fire or other casualty, or operation beyond its design range. Repaired products have a 90-day warranty, or until the end of the original warranty period—whichever period is greater. ADC DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO ITS PRODUCTS AND ANY ACCOMPANYING WRITTEN MATERIALS. FURTHER, ADC DOES NOT WARRANT THAT SOFTWARE WILL BE FREE FROM BUGS OR THAT ITS USE WILL BE UNINTERRUPTED OR REGARDING THE USE, OR THE RESULTS OF THE USE, OF THE SOFTWARE IN TERMS OF CORRECTNESS, ACCURACY, RELIABILITY OR OTHERWISE. MODIFICATIONS Any changes or modifications made to this device that are not expressly approved by ADC DSL Systems, Inc. voids the user's warranty. All wiring external to the products should follow the provisions of the current edition of the National Electrical Code. SAFETY STANDARDS COMPLIANCE The ThinMux chassis has been tested and verified to comply with the applicable sections of the following safety standards: • GR 63-CORE - Network Equipment-Building System (NEBS) Requirements: Physical Protection • GR 1089-CORE - Electromagnetic Compatibility and Electrical Safety Generic Criteria for Network Telecommunications Equipment • Bi-national standard, UL-1950/CSA-C22.2 No. 950-95; Safety of Information Technology Equipment For technical assistance, refer to “Appendix C - Product Support” on page 19. ADC DSL Systems, Inc. 14402 Franklin Avenue Tustin, CA 92780-7013 Tel: 714.832.9922 Fax: 714.832.9924 Technical Assistance Tel: 800.638.0031 Tel: 714.730.3222 Fax: 714.730.2400 ISO 9001/TL 9000 DNV Certification, Inc. REGISTERED FIRM DOCUMENT: LTPH-UM-1088-02, ISSUE 2 ´,$;¶5}¨ 1204275
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Annotate, Fill forms, Extract, Assemble, Print high-res Producer : Acrobat Distiller 4.05 for Windows Creator : FrameMaker 6.0 Modify Date : 2002:01:07 09:48:02-08:00 Keywords : 150-2263-01, ACE-COM L1, VAMXHN0F, LTPS-UM-1088-02, Issue 2 (1204275) Author : ADC DSL Systems, Inc. Title : ThinMux Chassis User Manual Create Date : 2002:01:07 09:45:17 Page Count : 34 Page Mode : UseOutlinesEXIF Metadata provided by EXIF.tools