ADTRAN 414RG24X Wireless Mini PCI User Manual

Adtran Wireless Mini PCI Users Manual

Users Manual

Download: ADTRAN 414RG24X Wireless Mini PCI User Manual
Mirror Download [FCC.gov]ADTRAN 414RG24X Wireless Mini PCI User Manual
Document ID2995143
Application IDcPcGePqQa5ffJpwDSeZHuA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize20.13kB (251613 bits)
Date Submitted2016-05-18 00:00:00
Date Available2016-11-14 00:00:00
Creation Date2016-05-16 15:13:30
Producing SoftwareAcrobat Distiller 15.0 (Windows)
Document Lastmod2016-05-16 15:13:30
Document TitleMicrosoft Word - Wireless Card Installation Guide-XW325EH
Document CreatorPScript5.dll Version 5.2.2
Document Author: Elaine

Wireless Card Installation Guide
Card name: XW325EH 2.4G Radio Daughter card
Model/PN: 33500008x‐E (x=0~9, a~z, A~Z, blank, “‐” or “+”)
Description:
 802.11 b/g/n support on 2.4GHz radio with 2x2 MIMO antenna design
 The 2.4 GHz radio SHALL support the frequency band specified in 802.11b/g/n.
 The 2.4GHz radio SHALL incorporate a 2x2 MIMO antenna arrangement with 2
spatial streams
 The 2.4GHz radio SHALL support 20 and 40 MHz channels on the 2.4 GHz radio
1. Installation way
Step1: Find the board and make sure the quality
Step2: Assemble XW325EG in the miniPCIe socket.
Step3: Assemble with necessary screws. 2pcs per unit.
Step4: Assemble the antenna, 2pcs per unit
Step5 Assemble the top cover
Step6: Log in the unit to setup the configuration, IP: 192.168.1.1
2. Safety and Regulatory Compliance Notice
Module FCC ID: HDC414RG24X
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the
FCC compliance requirement of the end product, which integrates this module.
Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment
authorizations (e.g. Verification , Doc) of the host device to be addressed by the
integrator/manufacturer.
20cm minimum distance has to be able to be maintained between the antenna and the users
for the host this module is integrated into. Under such configuration, the FCC radiation
exposure limits set forth for a population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation
with the antenna while this end product is installed and operated. The end user has to be informed that
the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end
user has to also be informed that any changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate this equipment. If the size of the end product is
smaller than the palm of the hand, then additional FCC part 15.19 statement is required to be available in
the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
HDC414RG24X ". If the size of the end product is larger than the palm of the hand, then the following
FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of
FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including interference that may
cause undesired operation.
RSS-GEN 8.4 Notice for Canada
Module IC ID: 2250A-414RG24X
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de
20cm de distance entre la source de rayonnement et votre corps
OEM integrator is still responsible for testing their end product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC
peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain
laptop configurations or co-location with another transmitter), then the IC authorization is no
longer considered valid and the IC No. cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate IC authorization.
Modular OEM Integrator Notice
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following: “Contains transmitter module IC:
2250A-414RG24X”.
Contient le module d'émission IC: 2250A-414RG24X
CAN ICES-3 (B)/NMB-3(B)

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Elaine
Create Date                     : 2016:05:16 15:13:30+08:00
Modify Date                     : 2016:05:16 15:13:30+08:00
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.158975, 2016/02/13-02:40:29
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - Wireless Card Installation Guide-XW325EH
Creator                         : Elaine
Producer                        : Acrobat Distiller 15.0 (Windows)
Document ID                     : uuid:c0101893-af9d-4a14-812d-9fe87d2cfc56
Instance ID                     : uuid:bb6d6e6e-b9ae-45d6-86d5-b8612c772dfd
Page Count                      : 6
EXIF Metadata provided by EXIF.tools
FCC ID Filing: HDC414RG24X

Navigation menu