ADTRAN SR310N 4 Port ADSL2+ 11n 150Mbps Router User Manual UT300 R

SmartRG, Inc. 4 Port ADSL2+ 11n 150Mbps Router UT300 R

Exhibit 08 Users Manual

4 Port ADSL2+ 11n 150Mbps Router SR310N USER MANUAL
ADSL MODEM USER MANUAL - 2 - CONTENTS 1. OVERVIEW ................................................................................................................................. 4 1.1 ABOUT ADSL AND ADSL 2+ ............................................................................ 4 1.2 DEVICE INTRODUCTION ................................................................................ 4 1.3 LED STATUS INDICATION ............................................................................... 5 1.4 PROTOCOLS ................................................................................................... 5 1.5 FEATURES ....................................................................................................... 5 1.6 ABOUT WIRLESS ADSL .................................................................................. 6 2. HARDWARE INSTALLATION AND SOFTWARE CONFIGURATION ............................ 7 2.1 SYSTEM REQUIREMENT ............................................................................... 7 2.2 HARDWARE INSTALLATION ........................................................................... 7 2.3 SOFTWARE CONFIGURATION ....................................................................... 8 3. PROTOCOL CONFIGURATION ........................................................................................... 10 3.1 CONFIGURATION GUIDE ............................................................................. 10 3.2 RFC1483 BRIDGE CONFIGURATION ........................................................... 12 3.3 PPPOA AND PPPOE CONFIGURATION ....................................................... 12 4. APPLICATION OF DHCP ....................................................................................................... 16 4.1 TCP/IP PROTOCOL CONFIGURATION......................................................... 16 4.2 MODEM CONFIGURATION ........................................................................... 16 5. OTHER FUNCTIONS AND CONFIGURATION .................................................................. 18 5.1 STATUS CHECKING ...................................................................................... 18 5.2 CONFIGURATION OF MODEM’S IP ADDRESS AND PASSWORD .............. 19 5.3 WIRELESS CONFIGURATION ...................................................................... 20 6. RESET TO DEFAULT SETTING ............................................................................................ 24 7. SPECIFICATION ...................................................................................................................... 25 7.1 POWER SUPPLY ........................................................................................... 25 7.2 STANDARDS .................................................................................................. 25 7.3 ENVIRONMENT REQUIREMENTS ............................................................... 25 APPENDIX ..................................................................................................................................... 26 APPENDIX A. TROUBLESHOOTING .................................................................. 26 APPENDIX B. SPLITTER CONNECTION ............................................................ 27 APPENDIX C. CONFIGURATION OF TCP/IP PROTOCOL ................................. 27 APPENDIX D. SHIPPING LIST ............................................................................ 29 Reference Standards
ADSL MODEM USER MANUAL - 3 - Related Documents Definition & Acronyms ATU-C ADSL Transceiver Unit, Central Office End ATU-R ADSL Transceiver Unit, Remote Terminal End FEXT Far-end Cross Talk HDSL High-rate Digital Subscriber Line POTS Plain Old Telephone Service PSTN Public Switched Telephone Network WINS Windows® Internet Name Server ADSL Asymmetric Digital Subscriber Line OAM Operations, Administration And Maintenance QAM Quadrature Amplitude Modulation DMT Discrete Multitone DSL Digital Subscriber Line FEC Forward Error Correction ATM Asynchronous Transfer Mode WAN Wide Area Network PRD Pseudo-random Downstream PRU Pseudo-random Upstream LAN Local Area Network PVC Permanent Virtual Circuit SVC Switched Virtual Circuit PPP Point to Point protocol DNS Domain Name Server VPI Virtual Path ID VCI Virtual Circuit ID DSL Digital Subscriber Line IP Internet Protocol CO Central Office EC Echo Canceling
ADSL MODEM USER MANUAL - 4 - 1. OVERVIEW 1.1 ABOUT ADSL AND ADSL 2+ ADSL MODEM is a broadband Internet access device，which utilizes the high frequency segment of the phone line to transmit high-speed data without interfering with the voice transmission. The frequency of ADSL signal is higher than that of voice, so voice and ADSL signal can coexist in one line by using a splitter to insulate each from the other. ADSL data transfer on the asymmetry way. The upload speed is up to 1Mbps and download speed is up to 8Mbps. It is an ideal device for broadband access. Transmission performance of ADSL2 is improved comparing with the first generation of ADSL. These improvements are mainly concerned with long distance, anti-line-loss, anti-noise, etc. By doubling the transmission bandwidth, ADSL2+ has implemented a downlink rate as high as 24 Mbps. Therefore, Internet applications such as synchronous transmission of multi video stream, online games and huge capacity of downloading files are made possible. 1.2 DEVICE INTRODUCTION Figure 1.1 1 OVERVIEW
ADSL MODEM USER MANUAL - 5 - Interface introduction: a) Power Interface: 12V DC, 500mA. . b) Switch: To turn on or turn off the power. c) WIFI: To switch on or switch off the WIFI. d) LAN1~LAN4: Connect Ethernet port of the Gateway with 10/100BASE-T port of the computer using the network cable that comes with the modem e) Line: Connected with phone line or “ADSL” port of the splitter. 1.3 LED STATUS INDICATION Table 1.1 Steady light Flashing Fast flashing Off POWER (green) Power on / / Power off DSL(green) The modem is in good connection The modem is boot OK In handshaking status Power off Internet(green) Route mode and obtained IP address Route mode and Data transmitting or receiving / Bridge mode or no Data transmitting or receiving LAN(1-4) (green) Ethernet line is connected to PC Ethernet is transmitting data Ethernet line not connected properly WLAN(green) / / Wireless is transmitting data Disable Wireless WPS(green) / / Start WPS Disable WPS 1.4 PROTOCOLS ADSL Modem supports the following protocols: 1. PPPoA（PPP over ATM ） LLC encapsulation or VCMUX encapsulation (RFC2364) 2. PPPoE (PPP over Ethernet) LLC encapsulation or VCMUX encapsulation (RFC2516) 3. 1483 bridge（1483 Bridged IP over ATM）LLC encapsulation or VCMUX encapsulation (RFC1483) 4. 1483 routing（1483 Routing IP over ATM）LLC encapsulation or VCMUX encapsulation (RFC1483) 5. Classical IP over ATM (RFC1577) 1.5 FEATURES 1. Supports ANSI T1.413 ISSUE 2, ITU G.992.1 (G.DMT), ITU G.992.2 (G.LITE), ITU G.992.3 (ADSL2), ITU G.992.5 (ADSL2+), Annex M. 2. Web-based configuration and monitoring. 3. Supports up to 8 PVCs. 4. Routing function. 5. NAPT、DHCP function.
ADSL MODEM USER MANUAL - 6 - 6. Support GUI Upgrading. 7. ATM management function. 8. Wireless access distance is more than 150m 1.6 ABOUT WIRLESS ADSL An ADSL MODEM is a broadband Internet access device, which utilizes the high frequency segment of the phone line to transmit high-speed data without affecting the voice transmission. The frequency of the ADSL signal is higher than that of voice, so voice and ADSL signal can coexist in one line by using a splitter to insulate each from the other. ADSL data transfer adapts the asymmetry model. It supports upload transmission speed up to 2Mbps and download speed up to 24Mbps for ADSL2+. ADSL is an ideal device for broadband access. But the ADSL users are also limited by the cable and can’t move freely. Wireless ADSL is a new device that integrates WLAN and ADSL functions. User can slip the leash to visit Internet expediently as long as they install WLAN card into their computer. The device can be utilized in company, hotel, cafe, airport, station, and financial institution and home where there are many mobile users and the network infrastructures are difficult to establish. The wireless ADSL supports 802.11b, 802.11b+g, 802.11g, 802.11n and 802.11b+g+n mode with maximum data rate 150Mbps.
ADSL MODEM USER MANUAL - 7 - 2. HARDWARE INSTALLATION AND SOFTWARE CONFIGURATION 2.1 SYSTEM REQUIREMENT A computer with a network card with Ethernet interface. 2.2 HARDWARE INSTALLATION 2.2.1 HARDWARE CONNECTION Figure 2.1 To go online and make phone calls simultaneously, please refer to Appendix B: SPLITTER CONNECTION. 2.2.2 INSTALLATION STEPS 1. Connect line port of the ADSL MODEM to telephone jack with the telephone cord that comes with the 2 HARDWARE INSTALLATION AND SOFTWARE CONFIGURATION
ADSL MODEM USER MANUAL - 8 - modem. 2. Connect Ethernet port of the ADSL MODEM to Ethernet port of the computer using the network cable that comes with the modem. 3. Plug in the power cord , and turn on the power. 2.3 SOFTWARE CONFIGURATION 2.3.1 PREPARATION BEFORE SOFTWARE INSTALLATION Before the installation, please confirm information below or consult with the ADSL service provider. Table 2.1 shows all the information needed to configure for different protocols. Table 2.1 Protocol Virtual Dial Mode Private Line Mode PPPOE PPPOA 1483 Bridged Necessary Information VPI VPI VPI VCI VCI VCI User name User name Password Password 2.3.2 COMPUTER CONFIGURATION The default factory-set IP Address for the ADSL MODEM is: 192.168.1.1. The Subnet Mask is: 255.255.255.0. Users can configure ADSL MODEM through an Internet browser. ADSL MODEM can be used as a gateway and DNS server and users need to set the computer’s TCP/IP protocol as follow: 1. Set the computer at same Internet segment with ADSL MODEM so as to enter ADSL MODEM configuration page through a browser. 2. Set the computer’s gateway’s IP address the same as the ADSL Modem’s. 3. Set the computer’s DNS server’s IP address the same as the ADSL Modem’s or that of an effective DNS server. If the user has any question regarding the computer’s TCP/IP protocol, please refer to APPENDIX C: TCP/IP PROTOCOL CONFIGURATION. 2.3.3 ADSL MODEM CONFIGURATION Open the browser; input http://192.168.1.1 in the address column. Press “Enter” key then the entry dialog box will pop up as Figure 2.2, Input username: admin, and password: 1234 then press “OK”. The ADSL MODEM configuration page will be shown.
ADSL MODEM USER MANUAL - 9 - Figure 2.2 2.3.4 ADSL MODEM WORK MODE CONFIGURATION 1． For different protocols, the users need to set ADSL Modem accordingly as listed below: Table 2.2 PPPoE PPPoA PVC Protocol Use DNS User Name Password √ PPPoE Enable √ √ √ PPPoA Enable √ √ 1483 Bridged PVC Default route √ Disable Note: √ means configure according to ADSL service provider’s instructed value. PPPoE can also be realized via third party dialup software. User Manual Reference Chapter PPPoE PPPoA 1483 Bridged 3.3 3.3 3.2 2． After getting through every page for parameters set-up, click “save” to save the value in ADSL MODEM 3． Click the “SysRestar” on “Maintenance” Tab to enter the page as Figure 2.3.You can choose “Current Settings” and Click “Restart” button to reboot the ADSL MODEM.(You can also choose the “factory default settings” in order to restart the modem to default configuration.) Figure 2.3
ADSL MODEM USER MANUAL - 10 - 3. PROTOCOL CONFIGURATION If the configuration is bridge encapsulation, there is no need to configure any more parameters. Only need to use the third party dial-up software to connect the Internet. Totally, this router supports：PPPoA、PPPoE、Bridging. For detail configuration information, please check the following configuration guide. 3.1 CONFIGURATION GUIDE Click “Internet” on “Interface Setup” Tab. You can modify the configuration. Note: At most we can have eight connections. You can got the detail about the default seven connections after you click the button “PVCs Summary”as Figure 3.1 Figure 3.1 If you need to add a new connection, please modify an existing connection For example, if you need to add a new connection “VPI/VCI=8/88” (The correct PVC (VPI/VCI) you can get from the ISP.) instead of the connection “VPI/VCI=0/33”. You can modify as Figure 3.2 and choose “PVC0” and find the change as Figure 3.3. 3 PROTOCAL CONFIGURATION
ADSL MODEM USER MANUAL - 11 - Figure 3.2 Figure 3.3 The Modem supports three ADSL protocol modes. Choose the protocol which is appointed by ISP and PVC encapsulation. Below, we introduce the configuraion of the three protocol modes.
ADSL MODEM USER MANUAL - 12 - • PPP over ATM (PPPoA) • PPP over Ethernet (PPPoE) • Bridging Some connection lines need to confirm the LLC or VC, if you can’t confirm, please don’t modify the default value or ask your ISP. 3.2 RFC1483 BRIDGE CONFIGURATION If you get the correct PVC (VPI/VCI) which you can get from the ISP, you don’t need modify another parameter. Click “save” to save configuration as Figure 3.4. Figure 3.4 3.3 PPPOA AND PPPOE CONFIGURATION PPPoE is also known as RFC 2516. It is a method of encapsulating PPP packets over Ethernet. PPPoA is also known as RFC2364 and named as Peer to Peer Protocol over ATM. As PPPoE, it also has all the features of PPP. Although it’s based on ATM protocol, the setting of all the other parameters is similar with
ADSL MODEM USER MANUAL - 13 - PPPoE. So we only introduce PPPoE in detail here. In Figure 3.4, select PPP over Ethernet (PPPoE), entering the configuration interface, as Figure 3.5 Figure 3.5
ADSL MODEM USER MANUAL - 14 - In Figure 3.4, select PPPoA from “Encapsulation”entering the configuration interface, as Figure 3.6 Figure 3.6
ADSL MODEM USER MANUAL - 15 - Select “Get IP Address Dynamic”and enter Severvice name、username、password.  Broadband User Name: Your account from ISP to access Internet.  Password: Input the password assigned by your ISP.
ADSL MODEM USER MANUAL - 16 - 4. APPLICATION OF DHCP Apart from being a modem, ADSL Modem can also support router and DHCP applications, which are especially applicable for small business, small scale LAN, net-café, etc. The ADSL Modem can work as a router and DHCP sever without proxy server. The configuration steps are shown below: 4.1 TCP/IP PROTOCOL CONFIGURATION 1. Set IP address as “Automatically obtain IP address”; 2. Set gateway’s IP the same as Modem’s; 4.2 MODEM CONFIGURATION 1. Set protocol as described in Chapter 3. 2. DHCP sever settings: a) Click “lan” label of Page “Interface Setup”. Define DHCP starting IP Address and IP Pool Count shown as Figure 4.1. b) Fill in the starting IP address. Here we will use 192.168.1.2 as an example. c) Do not change other options. Click “Save” to save the config. 4 APPLICATION OF DHCP
ADSL MODEM USER MANUAL - 17 - Figure 4.1
ADSL MODEM USER MANUAL - 18 - 5. OTHER FUNCTIONS AND CONFIGURATION 5.1 STATUS CHECKING The working status of ADSL MODEM can be monitored by some pages. 1． Overview of Device Information As shown in Figure 5.1, the information of Firmware Version, ADSL firmware Version, ADSL link status, link speed and LAN interface can be viewed on this page. 5 OTHER FUNCTIONS AND CONFIGURATION
ADSL MODEM USER MANUAL - 19 - Figure 5.1 5.2 CONFIGURATION OF MODEM’S IP ADDRESS AND PASSWORD 1. CONFIGURATION OF MODEM’S IP ADDRESS As a network device, ADSL Modem has its own IP address and MAC address. The factory sets the ADSL Modem at a default IP address of 192.168.1.1 and subnet mask of 255.255.255.0. The user can configure these
ADSL MODEM USER MANUAL - 20 - addresses through the LAN page. 2. Configuration of administrator’s password and user’s password When logging on the setting page of ADSL Modem, the system requires user name and password to verify for permission. The default administrator’s account is “admin” and the default password for this account is “1234”. The user, through the user configuration tab on Administration page, can change the passwords. (Attention: please remember the password after changing otherwise you will not be able to change configuration after saving.) 5.3 WIRELESS CONFIGURATION Press “WIRELESS” on the top of web pages to enter wireless section. You can select to configure wireless setup, security and management. 5.3.1 WIRELESS SETUP Click “WIRELESS” on the top menu to setup basic wireless parameters. In default, check “Access Point” box to launch wireless AP. 5.3.1.1.Access Point Settings  SSID (Service Set Identifier): The mobile users cannot access WLAN until setting their SSID as the same value of the wireless ADSL. The SSID value of the ADSL is “default”  Current Channel：To denote the different frequency of wireless signals whose value is from 1 to 11. The default value is”11”. If there are more than one APs located in the same area, each of them must works at different channels to reduce interference. For Example: Three APs are install in the same place, the AP’s channel should be 1,6 and 11 respectively.  Wireless mode: The default setting is 802.11b+g+n (Mixed mode). If you do not know or have among 11n 11g and 11b devices in your network, then keep the default setting  Beacon interval: The Beacon Interval value indicates the frequency interval of the beacon. Enter a value between 20 and 1000. A beacon is a packet broadcast by the Router to synchronize the wireless network.  RTS/CTS Threshold: The RTS (Request To Send) threshold (number of bytes) for enabling RTS/CTS handshake. Data with its frame size larger than this value will perform the RTS/CTS handshake. Setting this attribute to be larger than the maximum MSDU (MAC service data unit) size turns off the RTS/CTS handshake. Setting this attribute to zero turns on the RTS/CTS handshake Enter a value between 1500 and 2347.  DMIT: This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM).
ADSL MODEM USER MANUAL - 21 - Figure 5.3
ADSL MODEM USER MANUAL - 22 - 5.3.1.2. Multiple SSID’S Settings SSID Index, SSID: The SSID is the unique name of a wireless access point (AP) to be distinguished from another. For security propose, change the default name to a unique ID name to the AP which is already built-in to the router’s wireless interface. It is case sensitive and must not excess 32 characters. Make sure your wireless clients have exactly the SSID as the device, in order to get connected to your network. Broadcast SSID: Select Yes to hide the SSID in so a station cannot obtain the SSID through passive scanning. Select No to make the SSID visible so a station can obtain the SSID through passive scanning. Authentication Type: To prevent unauthorized wireless stations from accessing data transmitted over the network, the router offers highly secure data encryption, known as WEP.&WPA. If you require high security for transmissions, there are two alternatives to select from: 64-bit WEP and 128-bit WEP. WEP 128 will offer increased security over WEP 64. You can disable or enable with WPA or WEP for protecting wireless network. The default type of wireless is disabled and to allow all wireless computers to communicate with the access points without any data encryption 5.3.1.3. Wireless MAC Address Filter The MAC filter screen allows you to configure the router to give exclusive access to up to 32 devices (Allow Association) or exclude up to 32 devices from accessing the router (Deny Association). Every Ethernet device has a unique MAC (Media Access Control) address. The MAC address is assigned at the factory and consists of six pairs of hexadecimal characters, for example, 00:AA:BB:00:00:02. You need to know the MAC address of the devices to configure this screen. To change your router’s MAC filter settings, click Wireless LAN, MAC Filter to open the MAC Filter screen. The screen appears as shown. . Active: Select Actived to enable MAC address filtering. Action: Define the filter action for the list of MAC addresses in the MAC address filter table. Select Deny Association to block access to the router, MAC addresses not listed will be allowed to access the router. Select Allow Association to permit access to the router, MAC addresses not listed will be denied access to the router. MAC Address: Enter the MAC addresses (in XX:XX:XX:XX:XX:XX format) of the wireless station that are allowed or denied access to the router in these address fields. 5.3.1.4 WEP Key 1 to Key 4: Enter the key to encrypt wireless data. To allow encrypted data transmission, the WEP Encryption Key values on all wireless must be the same as the router. There are four keys for your selection. input format is in HEX style, 5 and 13 HEX codes are required for and 128-bitWEP respectively. If you chose WEP 64-bits, then enter any 5 ASCII characters or 10 hexadecimal characters ("0-9", "a,b,c,d,e,f"). If you chose WEP 128-bits, then enter 13 ASCII characters or 26 characters ("0-9", "a,b,c,d,e,f"). You must configure all four keys, but key can be activated at any one time. The default key is key 1. 5.3.1.5 WPA-PSK Encryption: TKIP (Temporal Key Integrity Protocol) utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers.
ADSL MODEM USER MANUAL - 23 - Pre-Shared key: The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters. The WPS Hardware Push Button and LED behaviors are defined as below: 1）Physical push button is pressed down and holds until the LED starts flashing, WPS starts to process and the LED will flash. 2）Push button (in the web UI) is pressed, WPS starts to process and the LED will flash. 3）Once the PIN is entered, WPS starts to process and the LED will flash. 4）Once the connection is successfully established between the router and the client, the LED will remain in solid for 5 seconds to tell the users that the connection has been established. 5）After 5 seconds, the LED will light off to indicate users that the router is ready for a new WPS connection 5.3.2 APPLY WIRELESS AP After you changed wireless parameters in wireless section, press "Save" button can apply the changes.
ADSL MODEM USER MANUAL - 24 - 6. RESET TO DEFAULT SETTING If you are experiencing difficulty logging on to the configuration page (For example: you forget the password), you can reset the ADSL MODEM to the default configuration，Then you will be able to log on with the default username and password. Method: 1) Turn on the ADSL MODEM. 2) Keep pressing the RESET BUTTON for 6 seconds. 3) Release the RESET BUTTON when the PC light off. 4) Done. 6 RESET TO DEFAULT SETTING
ADSL MODEM USER MANUAL - 25 - 7. SPECIFICATION 7.1 POWER SUPPLY  Exterior power adapter  Input: 110VAC, 60Hz  Output: 12VDC，500mA.  Polarity： 7.2 STANDARDS  EMI/Immunity: FCC Part 15 Class B, CE Mark (EN55022 Class B/EN50082)  Safety Standard: UL, EN60950, 3C  Communication: FCC Part 68, CYR21  Electromagnetic: in accordance with FCC, ETSI and CISPR standard 7.3 ENVIRONMENT REQUIREMENTS  Temperature: 5℃－40℃(41F－104F)  Relative humidity:30%－90%  Electromagnetic disturbance：FCC PART15&68 7 SPECIFICATION
ADSL MODEM USER MANUAL - 26 - APPENDIX APPENDIX A. TROUBLESHOOTING Phenomena Solution The indicator of power supply is not on 1. Make sure the connection of power supply is good. 2. Make sure the switch of power supply is turned on. 3. Make sure the output of power supply is correct. The indicator of LAN is not on 1. Check the connection between the cable and the network card. 2. Make sure that the correct cable is used. 3. Make sure the cable works fine by pinging the host IP address. Can not access Internet or remote networks 1. Make sure the problems listed above are eliminated. 2. Make sure the software configuration of the ADSL Modem is correct. 3. Make sure you have restarted the ADSL Modem after configuration change. 4. Check IP connection using ping command. 5. Make sure the DNS of the computer is correct. Can’t access some web server 1. The MTU of operating system might be too large. 2. Some operating systems might need to be patched. Can not log on to the configuration page 1. Make sure the LAN indicator is on. 2. Make sure the configuration of TCP/IP is correct. 3. Make sure the data indicator of Modem is on when using Ping command. 4. Make sure the user name and password is correct. 5. Reset the device. APPENDIX
ADSL MODEM USER MANUAL - 27 - APPENDIX B. SPLITTER CONNECTION 1. Splitter 2. Connection Firstly, use a telephone cord to connect the LINE port of the splitter and the RJ-11 port (the phone jack) on the wall. Then use another telephone cord to connect the ADSL port of the splitter and the LINE port of the ADSL Modem. Finally, use another telephone cord to connect the telephone set and the PHONE port of the splitter. APPENDIX C. CONFIGURATION OF TCP/IP PROTOCOL Here we will explain the configuration which using Windows 2000 operation system as an example. For other operation systems the process is similar. 1. Right click on the “Local Area Connection”, click “Properties” on the pop up menu, as shown in Figure C.1.
ADSL MODEM USER MANUAL - 28 - Figure C.1 2. The dialog box of networks is shown in Figure C.2. On the “General” property page select “Internet Protocol(TCP/IP)”，and then click the “Properties” button. Figure C.2 3. The “Internet Protocol (TCP/IP) properties” pop up window is shown as Figure C.3. Select “Use the following IP address”. Input the following IP address: 192.168.1.11 and subnet mask: 255.255.255.0 (These addresses and subnet mask are similar with the factory default setting. The user can set different IP addresse and subnet mask whenever necessary). Select “Gateway”, input the default IP address of the gateway: 192.168.1.1 and IP address of Preferred DNS server: 202.96.209.133 (you can use your ISP’s address), IP address of Alternate DNS server: 202.96.209.5(you can use your ISP’s address). The result is
ADSL MODEM USER MANUAL - 29 - shown in Figure C.3. Figure C.3 4. Click “OK” button to return to the “Local Area Connection Property” dialog box. 5. Click “OK” button to close the Network property dialog box. APPENDIX D. SHIPPING LIST Make sure the following items are included in the box. If any one of them is missing, please contact the vendor immediately. ADSL MODEM ×1 User Manual ×1 Telephone Line(RJ-11) ×2 Power Adapter ×1 Cable Cat5 RJ45 ×1 Splitter ×1
ADSL MODEM USER MANUAL - 30 - FCC INFORMATION FCC Caution • Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • For product available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible. • This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.. THIS DEVICE MUST NOT BE CO-LOCATED OR OPERATING IN CONJUNCTION WITH ANY OTHER ANTENNA OR TRANSMITTER NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. Federal Communications Commission (FCC) Requirements, Part 15 This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ---Reorient or relocate the receiving antenna. ---Increase the separation between the equipment and receiver. ---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ---Consult the dealer or an experienced radio/TV technician for help. REGULATORY INFORMATION / DISCLAIMERS Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use on the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. MPE Statement (Safety Information) Your device contains a low power transmitter. When device is transmitted it sends out Radio Frequency (RF) signal. FCC Information to User This product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals. SAFETY INFORMATION In order to maintain compliance with the FCC RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use only with supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. Please use the factory recommended power supply.

Navigation menu