ADTRAN WE65 DUAL-BAND WIFI EXTENDER User Manual WE65ac Quick Start Guide

SmartRG, Inc. DUAL-BAND WIFI EXTENDER WE65ac Quick Start Guide

user manual

Extending the access range for your router is easy.If your routerdoes not support WPS (most do not), or the WPS method fails,follow the instructions in the "WITHOUT WPS" section. If yourrouter supports WPS, follow the instructions in the "WITH WPS"section.Note: If you want the WE65ac extender to broadcast on both 2.4GHz and 5 GHz channels, slide the button on the bottom of theextender to 5before proceeding with setup.WITHOUT WPS1. Connect the extender to your PC using an Ethernet cable.2. Plug the WE65ac extender into a power outlet near your PC.The lights on the extender flash and it boots up (about 25seconds). When the extender is ready, a browser windowopens.3. Enter the password for the extender and click Login. TheConnection Wizard page appears.4. Click Start at the bottom of the page. The Step 1 of 2 pageappears.5. Select a network from the list of available networks.6. Click Next. The Step 2 of 2 page appears.7. Enter the Wireless Key for the network you selectedand then click Finish.The extender searches for your wireless network. The lightsscroll from TOO FAR to OK to TOO CLOSE and back again.When the extender has found your router, a successmessage appears in the browser window.Note: If the range lights flash longer than 1 minute, makesure your router is switched on and move your extendercloser to it.8. Click OK. The Connection Wizard summary page appears.Take note of the SSID for the connected wireless network tomake it easier to find later.9. Close the browser window.10. Disconnect the Ethernet cable from the extender and yourPC, and then unplug the extender.11. Plug the extender into a power outlet halfway between yourrouter and the area where you wish to extend WiFicoverage. The Power light glows white.12. Within 2 minutes, press the WPS button on the bottom ofthe extender for 1 second and release.The extender searches for your network. The lights scroll from TOOFAR to TOO CLOSE and back again. When one of the lights glowssteadily, the extender has found your network.If the extender is too far from your router, the TOO FAR light glowsred. Plug the extender to an outlet closer to the router.If the extender is too close, the TOO CLOSE light glows red. Plugthe extender into an outlet further from the router.When the OK light glows white, you’ve found a suitable locationwith a good signal.Note: It is normal for the range lights to change occasionally.Wireless reception can vary according to the number of wirelessdevices in use at the same time, type of structure, etc.Warning: Do not press the Reset button unless you want to clearthe current settings. The Reset button is in a small circular hole onthe rear panel. If you want to restore the default settings, press theReset button gently for 1 second with a fine wire (such as a paperclip) inserted into the hole and then release. The system rebootsand returns to the factory defaults.CONNECTING DEVICESNow that setup is complete, you'll want to connect your WiFi clientdevices (Smartphone, tablet, laptop, etc.) to the new, extendednetwork. Look for a network name with “ext” at the end.For example, if your existing WiFi network is named "Rogers12345",the extended WiFi network name would be:lRogers12345ext (on the 2.4GHz band), orlRogers12345-5Gext (on the 5GHZ band)Log in with the same WiFi password that you use for your WiFirouter and your device is connected.WITH WPS1. Press the WPS button on your router and then gently pressthe WPS button on the extender.2. Alternatively, you can activate WPS connection as follows:a. Press the WPS button on your routerb. Follow steps 1-3 in the "WITH WPS"c. Click the Advanced tab and then, in the leftnavigation menu, click WPS Settings.d. Click the WPS button. A progress popup appears.When the connection is made, the progress popupcloses.
OTHER OPTIONSThree additional operation modes are supported:lRepeaterlStandalone Access PointlWiFi Client.For detailed information, refer to the WE65ac User Manual.ADDITIONAL SUPPORTIf you require further instructions, please contact the ServiceProvider from whom this product was purchased.RECORD WE65AC SETTINGSSSID:WIFI KEY:PASSWORD:COPYRIGHT 2016 SMARTRG INC. ALL RIGHTS RESERVED.Safety NoteThe socket outlet shall be installed near the equipment and shall be easily accessible.le socle de prise de courant doit être installé à proximité du matériel et doit être aisément accessible.FCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:lReorient or relocate the receiving antenna.lIncrease the separation between the equipment and receiver.lConnect the equipment into an outlet on a circuit different from that to which the receiver isconnected.lConsult the dealer or an experienced radio/TV technician for help.FCC Radiation Exposure StatementThis device complies with FCC radiation exposure limits set forth for an uncontrolled environmentand it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operatedin accordance with provided instructions and the antenna(s) used for this transmitter must beinstalled to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installersmust be provide with antenna installation instructions and consider removing the no-collocationstatement.This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation.Caution!Any changes or modifications not expressly approved by the party responsible for compliance couldvoid the user's authority to operate the equipment.Canada StatementThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject tothe following two conditions: (1) this device may not cause interference, and (2) this device mustaccept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exemptsde licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pasproduire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectriquesubi, même si le brouillage est susceptible d'en compromettre le fonctionnement.The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 andcompliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure andcompliance.Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter. This equipment should be installed and operated with a minimum distance of 20centimeters between the radiator and your body.Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenneou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20centimètres entre le radiateur et votre corps.This radio transmitter (identify the device by certification number, or model number if Category II)has been approved by Industry Canada to operate with the antenna types listed below with themaximum permissible gain and required antenna impedance for each antenna type indicated. Antennatypes not included in this list, having a gain greater than the maximum gain indicated for that type,are strictly prohibited for use with this device.Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro demodèle s'il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pourfonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal etl'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, oudont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation del'émetteur.5GHz 5150-5250 MHz band is restricted to indoor operations only.

Navigation menu