AIJI System AP-200 Fixed WLL Telephone (PCS CDMA) User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	552411
Application ID	CRje9Bj2E3ZmRDdnOE8gSg==
Document Description	Users Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	111.2kB (1390061 bits)
Date Submitted	2005-06-16 00:00:00
Date Available	2005-06-16 00:00:00
Creation Date	2005-06-16 17:17:02
Document Lastmod	2005-06-16 17:17:36
Document Title	Users Manual 1

CDMA2000 1X RTT Fixed
Wireless Telephone
Quick Start Guide & User’s Manual
MODEL : AP Series
CDMA2000 1X RTT WLL
CDMA2000 1X RTT WLL
Model : AP Series
REFERENCE & WARNING
REVISED HISTORY
DATE
Feb 28, 2005
CONTENTS OF CHANGES
Initial Release
Model : AP Series
REMARK
Please read this manual before operating the
phone, and keep it for the future reference.
2005 Aiji System Co., Ltd. All rights reserved. No
reproduction in whole or in part is permitted,
without prior written approval.
The information in this user manual is subject to
change without notice and does not represent a
commitment on the part of Aiji System Co., Ltd.
Model Number: AP Series
Version: Initial Release, Feb. 28, 2005
Follow the directions on this page to start using
your phone now. For more information, refer to
the rest of this user manual.
Aiji System Co.,Ltd.
Aiji System Co.,Ltd.
CDMA2000 1X RTT WLL
Model : AP Series
CDMA2000 1X RTT WLL
Model : AP Series
SAFETY INFORMATION
WARNING
• To reduce the risk of fire or electric shock, do not expose this
product to rain or moisture.
•Do not use this product near swimming pools or other bodies of
water.
•Before using your phone, check your output voltage.
Hospitals or health care facilities may be using equipment that
could be sensitive to external RF energy.
• If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
IMPORTANT
Before installing or operating this product read this information.
OPTIMAL PHONE PERFORMANCE
• Do not operate your product when holding the antenna, or when
someone is within four inches (ten centimeters) of the antenna.
Holding the antenna affects call quality and may cause the
telephone to operate at a higher power level than needed.
•For the best call quality, keep the antenna free from obstructions
and point the antenna straight up.
•Do not use the unit with a damaged antenna. Have your antenna
replaced by a qualified technician immediately. Use only a
manufacturer-approved antenna. Non-approved antennas,
modifications, or attachments could impair call quality, damage the
phone.
•RF energy may affect improperly installed or inadequately shielded
personal medical devices such as pace markers, hospital monitor.
Consult the manufacturer of any personal medical devices to
determine if they are adequately shielded from external RF energy.
Turn your terminal OFF in health care facilities when any regulations
posted in the areas instruct you to do so.
Aiji System Co.,Ltd.
▷Reorient or relocate the receiving antenna
▷ Increase the distance between the radio or television and the
telephone.
▷ Connect the equipment into an outlet on a circuit different from
that to which the terminal is connected.
▷ Consult you Authorized AIJI Dealer of an experienced radio/TV
technician for help.
• Use only the battery, antenna and AC power supply provided by
AIJI. Using any other type will invalidate the warranty.
• Only authorized personnel should service the phone and its
accessories. Faulty installation or service may be dangerous and
may invalidate the warranty.
• Do not use the unit in designated "No Cellular Phone Use" area.
• Avoid exposure to high temperature or humidity.
Aiji System Co.,Ltd.
CDMA2000 1X RTT WLL
Model : AP Series
• Avoid wetting the unit with any liquids. If the unit gets wet, turn the
power off immediately and remove the backup battery and AC power
supply. If the unit is inoperable, then return to the service agent for
service.
• Avoid shock or impact.
• We recommend you to charge the backup battery before initial use.
Backup battery may be discharged during delivery.
CDMA2000 1X RTT WLL
Model : AP Series
CDMA2000 Fixed
Wireless Te l e p h o n e
Quick Start Guide
CARE AND SERVICE
MODEL…AP Series
• Unplug the telephone from the wall outlet and remove antenna (or
disconnect antenna cable) before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for cleaning.
• If the unit fails for any reason, do not attempt to disassemble;
contact the telephone service provider for assistance.
• If any of the following conditions exist; unplug the unit at the wall
plug, remove battery, and call the service provider.
▷
▷
▷
▷
▷
The power supply cord is damaged or frayed.
Liquid has been spilled into the unit.
The unit has been exposed to rain or water.
The unit has been dropped or damaged.
The unit does not work normally by following the operating
instructions.
Aiji System Co.,Ltd.
Aiji System Co.,Ltd.
CDMA2000 1X RTT WLL
Model : AP Series
1. Getting to Know Your Phone
1.1 Key Definition
Description
Key
1. Activate MENU state (also MENU state in the call state)
CDMA2000 1X RTT WLL
Model : AP Series
1.3 Icons
1.3.1 Standby Icons
Icon
Description
Icon
Description
Signal strength in the service area.
Lock mode
1. Set the [DND (Do Not Disturb)] function. It prohibits incoming
calls when the phone is in the idle-state
In use
Off-hook mode
1. Send a dialed number when a call is placed and/or to redial
and \ send the last number dialed
1. Sound: 31 Ring tones/Alerts/Volume
2. Volume up (also function as a cursor in the edit state)
No Service
Alarm/Morning Call
New message
Battery status
Voice message
AC Power Mode
1. Activate SMS and Voice Mail state
1. Phone book
2. Volume down (also function as a cursor in the edit state)
1. Store phone numbers and any settings you select in the menu
within the phone's memory.
1. Delete the last digit/dial number (also exit without storing in the
MENU state)
2. Deactivate a state - No store a value
1.3.2 Sub Icons
Description
Icon
Icon
Description
Message sent successfully
Mobile
Message sending fail
Home
Read Message
Office
Locked Message
Other
3-way Calling
Incoming Call
Group
Outgoing Call
1. To make or receive a call using the speakerphone.
1.2 External Features
Features
Description
Antenna
Adjusting direction of antenna improves the voice and
data quality
RF Connector
For connection to basic antenna or external antenna
DC Power Jack
For connection to power adapter
RS-232C port
For connection to PC for Internet
Power Switch
To turn on/off the phone
Aiji System Co.,Ltd.
Missed Call
Aiji System Co.,Ltd.
CDMA2000 1X RTT WLL
Model : AP Series
CDMA2000 1X RTT WLL
Model : AP Series
2. Basic Functions
Turn on
your phone
1. Connect handset to the main set
2. Connect the antenna
3. Open the battery cover at the bottom of the main set
and Insert backup battery.
4. Turn "ON" the battery switch.
5. Close the battery cover and connect the AC power
supply.
Make a Call
1. Pick up the handset or press
2. Enter phone number
CDMA2000 Fixed
Wireless Te l e p h o n e
U s e r ’s Manual
button.
MODEL…AP Series
When the phone rings, pick up the handset or press
Answer a Call button
End a Call
Replace the handset or press
Redial
1. Pick up the handset or press
2. Press
button.
button
button.
1. Pick up the handset or press
button.
2. For the location numbers of one digit, press and hold
(1- touch/2-touch)
the corresponding digit key.
For the other entry numbers, press the first digit key(s)
briefly and hold down the last digit key.
Speed dial
10
Read new
message
Press
-> Inbox -> Select Card or Phone
Phone book
search
Press
button -> Enter the name
Aiji System Co.,Ltd.
Aiji System Co.,Ltd.
11
CDMA2000 1X RTT WLL
Model : AP Series
CDMA2000 1X RTT WLL
CONTENTS
1. Introduction
15
1.1 Highlights
1.2 Check Components
1.3 Installation
15
17
18
1.3.1 Connect Components
1.3.2 Installation Steps
1.3.3 Place the Terminal
1.4 Phone Overview
1.4.1 Key Definition
1.4.2 External Features
1.4.3 Viewing the Display Screen
1.4.4 Check the LCD Display
18
20
21
22
23
23
24
24
2. General Functions
25
2.1 Making a Call
2.2 Correcting Dialing Mistakes
2.3 Receiving Calls
2.4 Lock Mode (Quick)
2.5 Call Waiting / Call Forwarding
2.5.1 Call Waiting
2.5.2 Call Forwarding
2.6 Mute
2.7 Redialing Calls
2.8 Adjusting the Volume
2.9 Signal Strength
2.10 Caller ID Display
2.11 Speed Dialing
2.12 Phone book Features
2.12.1 Personal Phone Book Memory
26
26
26
26
27
12
Aiji System Co.,Ltd.
27
27
27
27
28
28
28
29
29
29
Model : AP Series
29
2.12.1.1 Saving Numbers in Your Personal Phone Book
2.12.1.2 Retrieving Numbers
2.12.2 Making a call from Your Phone Book
2.12.2.1 One-Touch Speed Dialing
2.12.2.2 Two-Touch Speed Dialing
2.12.2.3 Three-Touch Speed Dialing
2.12.2.4 Dialing from a Call History
30
30
30
30
31
31
3. Menu Features
3.1 General Guidelines to MENU Access and Settings
3.2 List of Menu State
3.3 Call History
3.3.1 Recent Calls
3.3.2 Incoming Calls
3.3.3 Outgoing Calls
3.3.4 Missed Calls
3.3.5 Call Timer
3.3.6 Call Memo
3.3.7 Clear History
3.4 Phone Book
3.4.1 Find Entry
3.4.2 New Entry
3.4.2.1 Creating a New Entry in the Phone's Memory
3.4.2.2 Storing Phone Numbers at Call's End
3.4.3 Edit Group
3.4.4 Memory Status
3.4.5 Phone Infomation
3.5 Message
3.5.1 Inbox
3.5.2 Write Message
3.5.2.1 How to write a Text
3.5.3 Outbox
3.5.4 Delete Messages
3.5.5 Message Settings
31
31
31
37
37
37
37
38
38
38
39
39
39
39
39
40
40
40
41
41
41
42
43
43
43
43
Aiji System Co.,Ltd.
13
CDMA2000 1X RTT WLL
Model : AP Series
3.5.5.1 Display Message
3.5.5.2 Auto Save
3.5.5.3 Auto Delete
3.5.5.4 Font Size
3.5.5.5 Delivery Acknowledgement
3.5.5.6 Store Message
3.6 Sound
3.6.1 Ring Tones
3.6.2 Alerts / Tones
3.6.2.1 No Service
3.6.2.2 Minute Minder
3.6.2.3 Connect Tone
3.6.2.4 Disconnect
3.6.3 Volume
CDMA2000 1X RTT WLL
44
44
44
44
44
45
45
45
45
46
46
46
46
46
Model : AP Series
Chapter 1. Introduction
1.1 Highlights and Features of AP series
Thanks for purchase of the AP Fixed Wireless Telephone. This
telephone has been designed to operate on the latest CDMA 2000 1x
RTT technology. This technology has greatly enhanced voice clarity
and can provide various advanced features. Basically this telephone is
designed for the desktop and the use in the office and a house. This
can be easily installed in any place using the wall mount bracket
(Optional Accessory).
3.7 Phone Setting
47
The telephone provides:
3.7.1 Hot Line
3.7.2 Alarm Clock
3.7.3 Language
3.7.4 Font Select
3.7.5 LCD Contrast
47
47
47
48
48
• 4-line LCD display with status indicator.
- 8-line LCD display to view text message easily.
3.8 Security
3.8.1 Lock Phone
3.8.2 Change Code
3.8.3 Restrict
3.8.4 Reset Phone
3.8.4.1 Reset Settings
3.8.4.2 Reset All
3.8.5 PIN
48
• 128 x 64 Graphic LCD display.
• Window UI (Graphic User Interface): Pop-Up Animation Menu.
• Phone book
- 200 memory locations to store names and telephone numbers
in the phone.
- Store name, 4 phone numbers (Mobile/Home/Office/Other),
group and ring sound per location.
- Group editing available.
48
49
49
49
49
49
49
3.9 Data Service
•Brilliant 16-polyphonic midi sound
50
•A choice of 31 rings and melodies.
Appendix A : Specification
51
•Alarm (Morning Call): Various setting options
(Once/Daily/Weekdays only (Mon ~ Fri)/Weekends)
•50 text messages can be stored in the phone.
14
Aiji System Co.,Ltd.
Aiji System Co.,Ltd.
15
CDMA2000 1X RTT WLL
Model : AP Series
• 99 Voice Mail.
• Call History (Record&Time):
Recent_30/Incoming_20/Outgoing_20/Missed_20
•
•
•
•
•
Speed dialing (1- touch, 2-touch and 3-touch) with a 200 number memory.
Call Forwarding/Call Waiting/Caller ID/Last Number Re-Dial
Alert (No Service / Minute Minder / Connect Tone / Disconnect Tone)
Emergency Call
Hot Line
•
•
•
•
•
Restrict Call
Security
Internet connection up to 153Kbps through RS-232C serial data port.
Support the Authentication Key (A-Key)
Various supplementary services such as Last Number Redial, Dial
Tone and On Hook etc.
• Optional Functions: R-UIM, Speaker phone, LCD backlight, Button backlight
CDMA2000 1X RTT WLL
1.2 Check Components
•Your package contains the following items. The illustrations below may look
different from your phone and accessories;
[ Main Unit with handset ]
[ User’s Manual ]
16
Aiji System Co.,Ltd.
Model : AP Series
[ Dipole Antenna ]
[ AC/DC power Adapter ]
[ Backup Battery ]
[ Power Cord ]
Aiji System Co.,Ltd.
17
CDMA2000 1X RTT WLL
Model : AP Series
• In addition, you can obtain the following accessories for your phone
from our local dealer in your country.
1) RS-232C Data Cable
CDMA2000 1X RTT WLL
Model : AP Series
•Connect curl cord of handset assembly to the RJ-11C port located at
the left side of the terminal.
2) Wall Mount Bracket
• Please make sure that these components are present before you
begin the unit installation. And then compare the following figures and
components. If components are missing or damage is found, contact
the store where you purchased the unit immediately.
1.3 Installation
You should follow each step carefully as shown below in order to
guarantee proper operation of CDMA Fixed Wireless Telephone.
•Open the battery case, securely connect the battery cord, place the
backup battery pack and close the case.
1.3.1 Connect Components (See the figures in "Installation Steps")
•Connect the antenna to the TNC antenna connector
located at the top side of the terminal. If you placed the
terminal on the flat surface, bend the antenna up right.
18
Aiji System Co.,Ltd.
Aiji System Co.,Ltd.
19
CDMA2000 1X RTT WLL
Model : AP Series
• Check output voltage.
• Connect the AC/DC Adapter cable to the DC input port located at the
topside of the terminal.
CDMA2000 1X RTT WLL
Model : AP Series
4) Open the battery cover at the bottom of the main unit.
5) Insert back-up battery in the bottom of the main unit. (Give care to polarity)
6) When you use terminal first, please turn "on" the battery switch.
7) Replace the Battery cover.
8) Connect the AC power supply.
Notice
Before using the terminal,please check battery
switch is on, after switching on it, use the phone.
▷If it is good, beep tone is heard.
▷it is not good (Booting is fail or beep tone is not heard), you have to
connect the adapter or backup battery, again.
•Please follow the below to get better voice quality;
1) Keep away from electrical appliances such as TV, computer, radio
and so on.
2) Keep terminal in a high and central location with no obstructions,
such as metal walls.
3) Raise the integral antenna of terminal to get maximum strength of
receive signal as shown figure at the next page.
1.3.3 Place the Terminal
•Place the terminal on the stable flat secure surface area (desk, table,
etc.). Serious damage may result if the unit falls. Do not place the
unit on, or within 1 meter of heaters or radiators. This unit is designed
for desktop usage. Avoid direct exposure to the sunlights and damp
area.
•Read the SAFETY INFORMATION located at the first part of this
document before you place the terminal.
1.3.2 Installation Steps
Please follow the below procedure to install the unit properly.
1) Connect Base handset to the handset connector.
2) Connect the antenna to the TNC connector (Turn right).
3) Bend the antenna up right.
20
Aiji System Co.,Ltd.
Aiji System Co.,Ltd.
21
CDMA2000 1X RTT WLL
Model : AP Series
CDMA2000 1X RTT WLL
Model : AP Series
1.4.1 Key Definition
1.4 Phone Overview
Key
The following shows key components of
your mobile phone.
Description
1. Activate MENU state (also MENU state in the call state)
1. Activate SMS and Voice Mail state
5.TNC Antenna
1.Handset
6.LCD Screen
2.Menu Key
3.Mute Key
7.OK Key
9.Clear Key
4.Curl Cord
8.Navigation Key
10.Alphanumeric
Keypad
1. Set the [DND (Do Not Disturb)] function. It prohibits incoming
calls when the phone is in the idle-state
1. Send a dialed number when a call is placed and/or to redial
and \ send the last number dialed
1. Sound: 31 Ring tones/Alerts/Volume
2. Volume up (also function as a cursor in the edit state)
1. Phone book
2. Volume down (also function as a cursor in the edit state)
1. Store phone numbers and any settings you select in the menu
within the phone's memory.
1. Delete the last digit/dial number (also exit without storing in the
MENU state)
2. Deactivate a state - No store a value
3. Press this key once in a menu, to go back one level.
1. Off Hook mode
2. To make or receive a call using the speakerphone.
11.Lock mode Key
12.OHD Key
1.4.2 External Features
Features
22
Aiji System Co.,Ltd.
Description
Antenna
Adjusting direction of antenna improves the voice and
data quality
RF Connector
For connection to basic antenna or external antenna
DC Power Jack
For connection to power adapter
RS-232C port
For connection to PC for Internet
Power Switch
To turn on/off the phone
Aiji System Co.,Ltd.
23
CDMA2000 1X RTT WLL
Model : AP Series
CDMA2000 1X RTT WLL
1.4.3 Viewing the Display Screen
Chapter 2. General Functions
The LCD shows icons on the top of the LCD screen. The icons indicate
the setting status and operating status of the phone.
Icon
Description
Icon
Description
Signal strength in the service area.
Lock mode
In use
Off-hook mode
No Service
Alarm/Morning Call
New message
Battery status
Voice message
AC Power Mode
1.4.4 Check the LCD Display
•After you follow the installation instruction 1.3.1 to 1.3.3, please
check the LCD for normal operation.
•If you may not see status of service, please repeat the 5th
instruction of 1.3.2. And conform Fixed Wireless Telephone to get
the proper signal strength from service operator system.
※The adapter type(with power cord) may be different by country
adaptation.
24
Aiji System Co.,Ltd.
Model : AP Series
2.1 Making a Call
When you make a call, follow these simple steps:
1) Make sure your phone is turned on.
2) Pick up the handset or press
button.
3) Listen for dial tone. If the service is not available, you hear a no
service tone.
4) Enter the phone number, with area code (if needed).
5) Wait for the Auto Time-out or press
• If the phone is locked, take the following step.
→ 6. Security Enter Password → 1Lock Phone Select ◉ Unlock
•Call Failed indicates that the call did not go through. Please
check Antenna Icon and call again a few minutes later.
6) The call is connected and you can start conversation.
7) To end the call, replace the handset or press
button.
Tip 1: To redial your latest outgoing call, press
to dial.
Tip 2: Your phone offers many different ways to make calls, including
Speed Dialing ("Using One / Two / Three Speed Dialing" on page
30) and using Call History ("Viewing Call History (Incoming,
Outgoing and Missed)" on page 37).
Tip 3: This phone has been restricted If this message displays on
your screen, then outgoing calls are in restricted mode. You can
only dial phone numbers saved in Emergency.
•If you want to turn off this function, take the following step.
→ 6. Security → Enter Password → 3 Restrict
→ 2 Outgoing Call → Select ▣No
Tip 4: When speed dialing is enabled, type in the phone book entry
number and hold the last digit until the call is made.
Aiji System Co.,Ltd.
25
CDMA2000 1X RTT WLL
Model : AP Series
2.2 Correcting Dialing Mistakes
If you make mistakes while dialing a number, press
once to erase
the last digit entered or hold down
for at least two seconds to delete
all digits.
2.3 Receiving Calls
1) Make sure your phone is on. If your phone is off, incoming calls go to
voicemail.
2) When phone rings, pick up the handset (or press
(Optional
function)).
3) Start conversation.
4) To disconnect the call, replace the handset (or press
(Optional
function)).
2.4 Lock Mode (Quick)
Use to prevent others from using your phone.
1) In standby mode, to activate the Lock Mode quickly, press the #
for 3 seconds. Lock mode Setting! will be displayed.
The lock code (password) is commonly the last 4 digits of your phone number.
Note To cancel the Lock Mode, Press
→ 6. Security Enter Password
1 Lock Phone Select Unlock
CDMA2000 1X RTT WLL
Model : AP Series
2.5.1 Call Waiting
Your WLL service may offer a call waiting function. While a call is in
progress, you may hear two beeps indicating another incoming call.
When call waiting is enabled, you may put three active calls on hold while
you answer the other incoming call.
1) Press
to receive a waiting call.
2) Press
again to switch between calls.
2.5.2 Call Forwarding
This feature enables incoming calls to be rerouted to a number that you
specify. For example, you may wish to forward your business calls to
your mobile phone while you are not in the office.
2.6 Mute
The mute function prevents the other party from hearing your voice, but
allows you to hear the other party.
1) Press
during a call.
2) To cancel Mute, press
again.
2.7 Redialing Calls
2.5 Call Waiting / Call Forwarding
This menu contains network services, which allow you to forward
incoming calls when you can't answer a call, to receive a second call.
Please contact your service provider to check their availability and
details.
26
Aiji System Co.,Ltd.
1) Press
to redial the last number in call history (Recent Calls).
•You can also redial any of the last 60 numbers you have dialed,
received and missed. The last 30 numbers are stored in the call
history (Recent Calls) list. (See the Call History List on page 37.)
Aiji System Co.,Ltd.
27
CDMA2000 1X RTT WLL
Model : AP Series
2.8 Adjusting the Volume
The volume keys on the top side of the phone can be used to adjust the
earpiece, ringer, and keypad beep volumes. The upper key (
) is
used to increase and the lower key (
) is used to decrease the
volume.
•You may adjust the earpiece volume during a call.
CDMA2000 1X RTT WLL
Model : AP Series
2.11 Speed Dialing
Speed dialing is a convenient feature, which allows you to make phone
calls quickly and easily. Your phone recalls the phone number from your
personal directory, displays it briefly and then dials it.
1) From off-hook stage, press the memory number (1 through 200)
corresponding to the appropriate entry, and hold for a few seconds.
Tip 1: You should check with your service provider to ensure they
offer this feature.
2.9 Signal Strength
The call quality depends on the signal strength in your area. The current
signal strength is displayed on the screen as the number of bars next to
the signal strength icon: The more bars, the better the signal strength. If
the signal quality is poor, move to an open area. If you are in a building,
the reception may be better near a window. For maximum reception,
make sure that the antenna is fully extended.
2.10 Caller ID Display
Caller ID lets you know who is calling by displaying the number of the
person calling when your phone rings. If the caller's name and number
are already stored in your phone book, the corresponding name appears
with the number.
Tip 1: The LCD of the phone displays information such as:
•Date and Time
•Caller ID (caller's information [name and/or number])
•Number of missed calls
•Number of new messages
•No service status and Power Save Mode.
The phone will display most recent information.
28
Aiji System Co.,Ltd.
2.12 Phone Book Features
You can store up to 200 entries in your phone book with easy access to
your most frequently dialed phone numbers and make a call by pressing
entry number in off-hook state.
2.12.1 Personal Phone Book Memory
The phone has 200 personal phone book entry numbers where you can
store up 4 phone numbers with 16 digits for each phone number
2.12.1.1 Saving Numbers in Your Personal Phone Book
1) Input the phone number that you want to save (up to 16 digits).
2) Press
→ Select '1.Save' → Press
3) Select your desired label types Mobile, Home, Office, Other
using the upper key (
) and the lower key (
).
4) Enter a name for the phone number (up to 16 characters)Press
If you do not want to enter a name, go to the next step.
5) You may select the desired ID ring type and group
No Group, Family, Friend, Office, Other.
Aiji System Co.,Ltd.
29

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2005:06:16 17:17:36-03:00
Create Date                     : 2005:06:16 17:17:02-03:00
Title                           : 
Author                          : 
Producer                        : 
Page Count                      : 15
Mod Date                        : 2005:06:16 17:17:36-03:00
Creation Date                   : 2005:06:16 17:17:02-03:00
Metadata Date                   : 2005:06:16 17:17:36-03:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools