AIRTAME APS AT-DG1 HDMI Dongle, model AT-DG1 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2595644
Application ID	Ds8R7zBx0sRHXRieXUUblQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.11kB (88898 bits)
Date Submitted	2015-04-24 00:00:00
Date Available	2015-04-24 00:00:00
Creation Date	2014-11-27 16:29:46
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2014-11-27 16:29:46
Document Title	User Manual
Document Creator	Adobe InDesign CS6 (Macintosh)

AIRTAME
How to use, Safety, Regulatory
and Warranty information
For more information visit
airtame.com/support
WHAT’S IN THE BOX?
AIRTAME:
The AIRTAME Dongle plugs into
the HDMI port on your TV
Micro USB Cable:
To provide power for AIRTAME
you need to connect the Micro
USB cable between AIRTAME
and the AC Adapter
HDMI Extension Cord:
The HDMI extender can be used
if AIRTAME not fit behind the TV
because of limited space.
Power supply:
The provided power supply
should be used to power
AIRTAME
Micro USB cable
HDMI extension cable
AC power adapter
EU power adapter
UK power adapter
SET UP PROCESS
More help can be found at:
setup.airtame.com
Step 1
Plug AIRTAME into an HDMI port in the
back of your TV. Take the included USB
cable and plug the smaller end into
AIRTAME and the other end into the
included power adapter. Power it up.
Step 2
On your TV, select the HDMI input
source you just plugged AIRTAME in
to. You should see an AIRTAME setup
screen now.
Step 3
Go to setup.airtame.com from your
browser on your phone, tablet
or computer - and follow further
instructions.
SAFETY PRECAUTIONS
AIRTAME has been designed
with high attention to the safety
for the user. However if used
improperly, AIRTAME have
the potential for causing fire,
electrical shock or personal
injury. To avoid any accident
please pay attention to these
guidelines:
• Use only the power supply
and Micro USB cable provided
by AIRTAME. Using other
cables and power supplies can
potentially damage or influence
the functionalities during use.
• AIRTAME generates heat
during use that increases the
temperature of the outside of
AIRTAME. It should be powered
off and cooled before removing
from your monitor.
• Stop use of AIRTAME imidiately
if the device funtions in an
abnormal manner, produces
unusual sounds or smell and/or
becomes to hot to touch.
• Do not expose AIRTAME
including the Micro USB cable,
HDMI extender or power supply
to water or extreme conditions
(moisture, heat, cold, dust) as
it potentially could result in
malfunction when exposed to
such elements.
• Do not attempt to disassemble
or repair AIRTAME yourself.
Doing so voids the limited
warranty and could harm you,
your television, and/or the
device.
• Be careful when using the
Power supply and only use in
combination with AIRTAME in
dry locations to avoid the risk of
electric shock.
LICENSE AGREEMENT
Software license terms related
to AIRTAME can be found at
airtame.com/support/license
When using AIRTAME you
accept the agreement to those
terms.
WARRANTY
INFORMATION
Warranty information applicable
for your country can be found at
airtame.com/support/warranty
LEGAL NOTICES
Model AT-DG1
FCC ID: 2ADEFAT-DG1
IC: 12460A-ATDG1
Federal Communication
Commissions Interference
Statement
This equipment has been tested
and found to comply with the
limits for a Class B digital device,
pursuant to Part 15 of the FCC
Rules. These limits are designed
to provide reasonable protection
against harmful interference in
a residential installation. This
equipment generates, uses and
can radiate radio frequency
energy and, if not installed and
used in accordance with the
instructions, may
cause harmful interference
to radio communications.
However, there is no guarantee
that interference will not occur
in a particular installation. If
this equipment does cause
harmful interference to radio or
television reception, which can
be determined by turning the
equipment off and on, the user
is encouraged to try to correct
the interference by one of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
This device complies with Part
15 of the FCC Rules. Operation
is subject to the following two
conditions: (1) this device may
not cause harmful interference,
and (2) this device must accept
any interference received,
including interference that may
cause undesired operation.
FCC Caution: Any changes or
modifications not expressly
approved by the party
responsible for compliance
could void the user’s authority to
operate this equipment.
IEEE 802.11b or 802.11g operation
of this product in the U.S.A. is
firmware-limited to channels 1
through 11.
Wireless Radio Use: This device
is restricted to indoor use when
operating in the 5.15 to 5.25 GHz
frequency band.
IMPORTANT NOTE:
FCC Radiation Exposure
Statement:
To satisfy FCC and IC exposure
requirements, a separation
distance of at least 20 cm
should be maintained between
the antenna of this device and
persons during device operation.
Operations at closer than this
distance are not recommended.
The antenna used for this
transmitter must not be colocated in conjunction with any
other antenna or transmitter.
Note to US model owner:
To comply with US FCC
regulation, the country selection
function has been completely
removed from all US models.
The availability of some specific
channels and/or operational
frequency bands are country
dependent and are firmware
programmed at the factory to
match the intended destination.
The firmware setting is not
accessible by the end user.
INDUSTRY CANADA (IC)
NOTICES
English
“Under Industry Canada
regulations, this radio transmitter
may only operate using an
antenna of a type and maximum
(or lesser) gain approved for the
transmitter by Industry Canada.
To reduce potential radio
interference to other users,
the antenna type and its gain
should be so chosen that the
equivalent isotropically radiated
power (e.i.r.p.) is not more than
that necessary for successful
communication.”
“This device complies with
Industry Canada licence-exempt
RSS standard(s). Operation is
subject to the following two
conditions: (1) this device may
not cause interference, and
(2) this device must accept
any interference, including
interference that may cause
undesired operation of the
device.”
French
“Conformément à la
réglementation d’Industrie
Canada, le présent émetteur
radio peut fonctionner avec une
antenne d’un type et d’un gain
maximal (ou inférieur) approuvé
pour l’émetteur par Industrie
Canada.
Dans le but de réduire les risques
de brouillage radioélectrique à
l’intention des autres utilisateurs,
il faut choisir le type d’antenne
et son gain de sorte que la
puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse
pas l’intensité nécessaire
à l’établissement d’une
communication satisfaisante.”
“Le présent appareil est
conforme aux CNR d’Industrie
Canada applicables aux appareils
radio exempts de licence.
L’exploitation est autorisée aux
deux conditions suivantes : (1)
l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur
de l’appareil doit accepter
tout brouillage radioélectrique
subi, même si le brouillage est
susceptible d’en compromettre
le fonctionnement.”
EUROPEAN UNION
AIRTAME ApS declares that this
equipment is in compliance with
the essential requirements and
other provisions of Directive
1999/5/EC.
The full Decleration of
Conformity can be found at
airtame.com/support/cemarking
Waste management of AIRTAME
follows the WEEE Directive
2012/19/EU and the RoHS
recasst Directive 2011/65/EU.
More information can be found
at airtame.com/support/waste
AIRTAME was designed by:
AIRTAME ApS, Vestergade
20C 2nd, Copenhagen K 1456,
Denmark.
airtame.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2014:11:27 16:29:46+01:00
Metadata Date                   : 2014:11:27 16:29:46+01:00
Modify Date                     : 2014:11:27 16:29:46+01:00
Creator Tool                    : Adobe InDesign CS6 (Macintosh)
Instance ID                     : uuid:25478de6-b541-9449-959d-2c478970f455
Original Document ID            : xmp.did:EE7F1174072068118DBBFE674B209159
Document ID                     : xmp.id:0180117407206811822AF51443AF12BC
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:FA7F1174072068118C148ED90E9C5721
Derived From Document ID        : xmp.did:FB7F117407206811822AE2ECA8A4BDB0
Derived From Original Document ID: xmp.did:EE7F1174072068118DBBFE674B209159
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Macintosh)
History Changed                 : /
History When                    : 2014:11:27 16:29:46+01:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 12
Creator                         : Adobe InDesign CS6 (Macintosh)

EXIF Metadata provided by EXIF.tools