ALPS ALPINE 9ZUA145 Car Navigation Unit User Manual 68 29530Z12 A c3 comm FCC

Alpine Electronics Inc Car Navigation Unit 68 29530Z12 A c3 comm FCC

(Short-Term Confidential) User Manual_2

30-EN

[Wireless] is selected on the Setup main screen in step 3. See “Setup

Operation” (page 29).

Wireless Setup Menu screen

*This setting is only available when “Bluetooth” is set to “On” ( ).

1Select the desired item.

2To switch the setting, touch [ ], [ ], [ ], [ ], or mark the

checkboxes “Off”( ) or “On”( ).

• If “ ” appears, there is a further hierarchy. Touch the desired

item.

3Touch [ ] to return to the main source screen.

• To return to the previous List screen, touch [ ] or [ ] in the

previous page. For details, see “About Basic Operation for List

Screen” (page 18).

Bluetooth Setup

[Bluetooth] is selected on the Wireless Setup Menu screen in step 1. See

“Wireless (Bluetooth) Setup” (page 30).

You can register and set up Bluetooth compatible devices.

Setting item:

Bluetooth

Setting contents:

Off / On (Initial setting)

*Turn this setting “On” to automatically connect a registered Bluetooth

device whenever this unit is turned ON. See “Registering the Bluetooth

Device” if no device is registered.

Make sure the “Bluetooth” setting is “On” ( ). See “Bluetooth Setup”

(page 30).

You can display the Bluetooth device name and device address of this

unit.

Setting item:

Bluetooth Information

The Bluetooth device is used when a connectable Bluetooth compatible

device is searched and connected from this unit, or a new Bluetooth

compatible device is registered.

Setting item:

Set Bluetooth Device

1Touch [ ] (Search) of “No Device.”

Wireless (Bluetooth) Setup

Bluetooth

Bluetooth Information*

Set Bluetooth Device*

Hands-free Device Priority*

iPhone Auto Pairing*

Device

Passcode Change

Default Phone Book Format

Phone Speaker

Microphone Select (X108U/INE-W967HD only)

The following steps 1 to 3 are common to each “Setting

item” of Wireless Setup. See each section for details.

Off: Bluetooth function is not used.

On*: Select when you would like to pair your Bluetooth

compatible phone with this unit.

Displaying Bluetooth Information

Registering the Bluetooth Device

31-EN

2Touch [ ] (Audio), [ ] (Hands-free) or [ ] (Both)

of the device you want to connect from the list.

• You can register up to 5 Bluetooth compatible mobile phones.

• You can connect three Bluetooth Devices; two exclusively for

Hands-Free Phone and one exclusively for Bluetooth Audio.

• When you register a Hands-Free Phone for the first time, Priority1

is set automatically. When you connect two Hands-Free Phones,

select “HFT” or “Both.” You can then set the priority on the

Priority setting screen. For details, see “Hands-free Device Priority

Setting” (page @@).

3When the device registration is complete, a message

appears and the device returns to normal mode.

• The Bluetooth registration process differs depending on the device

version and SSP (Simple Secure Pairing). If a 4 or 6 character Passcode

appears on this device, enter the Passcode using the Bluetooth

compatible device.

If a 6 character Passkey appears on this device, make sure the same

passkey is displayed on the Bluetooth compatible device and touch “Yes.”

• If all 5 devices have been registered, you cannot register a 6th device. To

5 devices first.

Setting the Bluetooth Device

Select one of 5 paired Bluetooth compatible devices that you previously

registered.

Touch [ ] (Audio) or [ ] (Hands free) of the device you

want to connect from the Paired Device list.

Deleting a Bluetooth Device from the list

You can delete the information of a previously connected Bluetooth

compatible device.

1Touch [ ] (Delete) of the Bluetooth compatible device

to delete from the Paired Device list.

2Touch [OK].

• Touching [Cancel] will cancel the setting.

Make sure the “Bluetooth” setting is “On” ( ). See “Bluetooth Setup”

(page @@).

When you connect two Hands-Free Phones, set the priority of the

operation and the setting of incoming-outgoing calls.

Setting item:

Hands-free Device Priority

Setting contents:

Priority1 / Priority2

Touch the checkbox of Priority1/Priority2 of the Device

names that are connected to the unit to set them.

• When connected to two hands-free phones, operating restrictions apply

to the hands-free phone registered to Priority2. For details, see “Hands-

free Phone Control” (page @@).

Make sure the “Bluetooth” setting is “On” ( ). See “Bluetooth Setup”

(page 30).

When an iPhone is connected via USB and it is not on the Registered

Device list, it will be paired automatically.

Setting item:

iPhone Auto Pairing

Setting contents:

On / Off (Initial setting)

• This setting supports iPhones with iOS Ver.5.5 or later.

• When more than 5 Bluetooth devices are registered, Auto Pairing does

not start.

Device Setup

[Device] is selected on the Wireless Setup Menu screen in step 1. See

“Wireless (Bluetooth) Setup” (page 30).

You can make various settings for a Bluetooth compatible device.

You can set the code for connecting with a Bluetooth compatible device.

Setting item:

Passcode Change

Enter a 4-digit passcode, and then touch [OK].

• The initial number is 0000.

• For details on how to input the numeric keypad, see “Numeric Keypad

Input Operations” (page 75).

Audio: Sets for use as an Audio device.

Hands-free: Sets for use as a Hands Free Device.

Both: Sets for use as both an Audio device and Hands Free

Device.

Hands-free Device Priority Setting

iPhone Auto Pairing Setting

On: Performs iPhone Auto Pairing setting.

Off: Does not perform iPhone Auto Pairing setting.

Setting the Passcode

32-EN

You can select the character code that is used when transferring the

phone book or history from a mobile phone. If unreadable characters

appear in the transferred data, select the correct character code.

Setting item:

Default Phone Book Format

Setting contents:

Latin-1 / Latin-9 (Initial setting) / Russian / Chinese / Thai / Arabic / UTF-8 /

UTF-16LE / UTF-16BE

You can select which speaker in the car will output the audio from the

phone.

Setting item:

Phone Speaker

Setting contents:

All (Initial setting) / Front Left / Front Right / Front Left + Right

• The setting cannot be adjusted during a phone call. Adjust the setting

before placing a call.

• This option is not available when “External Audio Processor” (page 49)

is set to On.

You can select the built-in microphone or the supplied microphone as a

Hands-Free Microphone.

Setting item:

Microphone Select

Setting contents:

Built-in (Initial setting) / Add-on

[General] is selected on the setup main screen in step 3. See “Setup

Operation” (page 29).

General Setup Menu screen

*1 You can make this setting in the Sound Setup screen of the Shortcut

Setup. For details, see “Sound Setup Function” (page 19).

Changing the Character Code of the Phone

Book

Latin-1: ISO 8859-1

Latin-9: ISO 8859-15

Russian: ISO 8859-5

Chinese: GB18030

Thai: CP874

Arabic: CP1256

UTF-8

UTF-16LE

UTF-16BE

Selecting the Output Speaker

All: The sound is output from all speakers in car.

Front Left: The sound is only output from the front left speaker.

Front Right: The sound is only output from the front right speaker.

Front Left +

Right:

The sound is output from the front left and front right

speakers.

Setting the Microphone Select (X801D-U/INE-

W997D only)

Built-in: Use the built-in microphone.

Add-on: Use the supplied microphone.

General Setup

Sound

Balance / Fader *1

Rear Speaker*2

Subwoofer*2

Subwoofer Level*1, 2, 3, 5

Subwoofer Phase*2, 3

MX HD*1, 4, 5

EQ Presets*4, 5

Dual HD EQ*4, 5

X-Over*5

Time Correction (TCR)

Defeat

Source Volume Setup

Caller Level

Microphone Level

Ring Tone Level

Key Sound Feedback

Mute While Backing Up

Default Sound Settings

Picture Quality.

Video*6

Camera*7

Navigation

Display/Key

Screen/Lighting

Screen Color

Illumination Color (X108U/INE-W967HD only)

Text Scroll

Artwork Position

General

Language

Format

About

Demo Mode

Vehicle

Installation Status

33-EN

*2 You can also make the setting in the Bal./Fad. screen.

For details on how to adjust, see “Setting the Balance/Fader/Rear

Speaker/Subwoofer” (page 33).

*3 This setting is only available when “Subwoofer” is set to “On” ( ).

*4 When the Defeat setting is “On,” you cannot perform the set up.

*5 When the Sound Setup of the Shortcut Setup is selected to ”BASS

ENGINE SQ,” you cannot perform the set up.

*6 “Video” can be selected while a video is playing.

*7 The camera names are not displayed when Camera Select (page 46) is

set to “Off.”

1Select the desired item.

2To switch the setting, touch [ ], [ ], [ ], [ ], or mark the

checkboxes “Off” ( ) or “On” ( ).

• If “ ” appears, there is a further hierarchy. Touch the desired

item.

3Touch [ ] to return to the main source screen.

• To return to the previous List screen, touch [ ] or [ ] in the

previous page. For details, see “About Basic Operation for List

Screen” (page 18).

Sound Setup

[Sound] is selected on the General Setup Menu screen in step 1. See

“General Setup” (page 32).

You can set up items related to the sound quality.

Set Balance/Fader/Rear Speaker/Subwoofer/Subwoofer Level/

Subwoofer Phase in the Bal./Fad. screen.

Setting item:

Balance*1 / Fader*1 / Rear Speaker / Subwoofer*2 / Subwoofer Level*1, 2 /

Subwoofer Phase*1

*1 When selecting either of the above setting items, the Bal./Fad. screen is

displayed.

*2 When the Sound Setup of the Shortcut Setup is selected to “BASS

ENGINE SQ,” you cannot perform the set up.

Fad./Bal. screen

Enables you to change to each setting screen.

Balance/Fader Image area

Setting the Balance/Fader

Touch the desired point within the image area. Or touch [ ]

[ ] [ ] [ ].

Balance:

L15 to R15

Fader:

F15 to R15

• To reset to the initial setting (Balance: 0, Fader: 0), touch [Center].

Rear Speaker Setting

You can set the rear speaker output to “Off.”

Setting item:

Rear Speaker

Setting contents:

On (Initial setting) / Off

Turning Subwoofer ON/OFF

If an optional subwoofer is connected to the unit, make the following

setting.

Setting item:

Subwoofer

Setting contents:

On / Off (Initial setting)

Adjusting the Subwoofer Level

You can set the Subwoofer level when a Subwoofer is connected.

Setting item:

Subwoofer Level

Setting contents:

0 to 15 (Initial setting: 0)

• This setting is only available when “Subwoofer” is set to “On” ( ).

Setting the Subwoofer Phase

The subwoofer output phase is toggled Subwoofer Normal (0°) or

Subwoofer Reverse (180°).

Setting item:

Subwoofer Phase

Setting contents:

0° (Initial setting) / 180°

• This setting is only available when “Subwoofer” is set to “On” ( ).

The following steps 1 to 3 are common to each “Setting

item” of General Setup. See each section for details.

Setting the Balance/Fader/Rear Speaker/

Subwoofer

34-EN

Media Xpander (MX HD) makes vocals or instruments sound distinct

regardless of the music source. The HD-Radio (FM)/SiriusXM, USB

Flash drive and iPod/iPhone, will be able to reproduce the music clearly

even in cars with a lot of road noise.

Setting item:

MX HD

• When the Defeat setting is “On,” you cannot perform the set up.

• When the Sound Setup of the Shortcut Setup is selected to “BASS

ENGINE SQ,” you cannot perform the set up.

• The MX HD setting can be performed only when a source is currently

selected.

Adjustable source (media) and setting value

HD-Radio (FM)/SiriusXM: Off (Initial setting) / Level1 / Level2 / Level3

The medium to high frequencies become more clear, and produces

well balanced sound in all the bands.

Compressed Media: Off (Initial setting) / Level1 / Level2 / Level3

This corrects information that was omitted at the time of

compression. This reproduces a well-balanced sound close to the

original.

HDMI/AUX: Off (Initial setting) / Compressed Media / Movie / Music

Choose the MX HD mode (Compressed Media, Movie, or Music) that

corresponds to the media connected.

(Movie)

The dialog portion of the video is reproduced more clearly

(Music)

This disc contains a large quantity of data such as music clip. MX uses

this data to reproduce the sound accurately.

• The effectiveness increases as the MX HD setting value increases Level1

Level2 Level3.

• You can set this for each source.

• iPod/iPhone/USB Audio/Bluetooth Audio/Pandora/Bluetooth Pandora

correspond to Compressed Media.

10 typical equalizer settings are preset at the factory for a variety of

musical source material.

Setting item:

EQ Presets

Setting contents:

FLAT (Initial setting) / POP / ROCK / NEWS / JAZZ / ELECTRONIC /

HIP HOP / EASY LISTENING / COUNTRY / CLASSICAL

• Only one type can be set to ON.

• When Equalizer Presets is set, the linked Dual HD EQ settings are also

changed. We recommend storing Dual HD EQ settings in a Preset in

advance.

• The Equalizer Presets setting can be configured when Defeat is “Off.”

Parametric Equalizer (Dual HD EQ) can adjust the center frequency/Q

Adjustment (bandwidth)/level in the front seats and the rear seats,

respectively.

You can adjust only to the approximate frequency zone, but can then

compensate by performing advanced correction of the sound.

Setting item:

Dual HD EQ

• When the Defeat setting is “On,” you cannot perform the set up.

• When the Sound Setup of the Shortcut Setup is selected to “BASS

ENGINE SQ,” you cannot perform the set up.

1Adjust the Dual HD EQ to your preference.

Front/Rear speaker switching button

Not displayed when Front/Rear Sync is ”On” ( ).

Front/Rear speaker interlock button

Adjusting the Band

Touch [Band] to select the band to be adjusted.

Band1 Band2 ••• Band8 Band9 Band1

• You can select a band directly by touching the screen.

Setting the Media Xpander (MX HD) Equalizer Presets

Adjusting the Parametric Equalizer Curve

(Dual HD EQ)

On: When you want the Front and Rear speakers to have the

same setting, set to ”On” ( ).

Off: When you want to set the Front and Rear speakers

independently, set to ”Off” ( ).

35-EN

Adjusting the Frequency

Touch [ ] or [ ] of “Frequency” to adjust the frequency of the

selected band.

Adjustable frequency bands:

20 Hz to 20 kHz (in 1/3 octave steps)

Adjusting the Level

Touch [ ] or [ ] of “Level” to adjust the level of selected band.

Setting contents:

-14 to +14 (Initial setting: 0)

Setting the Bandwidth

Touch [ ] or [ ] of “Q Factor” to select the bandwidth.

Setting contents:

Wide (Initial setting) / Medium / Narrow

2To adjust another band, repeat step 1, and adjust all

bands.

3To store the adjusted setting value, touch and hold

[Preset 1], [Preset 2], or [Preset 3] for at least 2 seconds.

• Band2 and Band8 are the same as the Bass and Treble controls.

• For details on setting Bass and Treble, see “Adjusting Bass Level/Treble

Level” (page 20).

• Settings exceeding the frequency of adjacent bands are not available.

• While adjusting the Dual HD EQ, you should consider the frequency

response of the connected speakers.

• When the Dual HD EQ is adjusted, the Equalizer Presets are

overridden.

• When Equalizer Presets is set, the linked Dual HD EQ settings are also

changed. We recommend storing Dual HD EQ settings in a Preset in

advance.

• Touch [Flat] to initialize all values.

Calling the Dual HD EQ adjusted value

Calling the pre-set Dual HD EQ adjusted value.

Touch [Preset 1], [Preset 2], or [Preset 3] on the Dual HD EQ

screen.

The setting stored in the Preset will be recalled.

Before performing the following procedures, see “About the Crossover”

(page 37).

Setting item:

X-Over

• When the Sound Setup of the Shortcut Setup is selected to “BASS

ENGINE SQ,” you cannot perform the set up.

1Touch [Channel] to select the channel.

Each time you touch, the channel switches.

• The channel being adjusted is displayed in red.

2Adjust the crossover to your preference.

Selecting the Cut-Off Frequency

Touch [ ] or [ ] of “Frequency,” and then select the cut-off

frequency.

Setting contents:

20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) / 100 / 125 / 160 / 200 Hz

Adjusting the Slope

Touch [ ] or [ ] of “Slope,” and then adjust the HPF or LPF slope.

Setting contents:

0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct.

Adjusting the Level

Touch [ ] or [ ] of “Level,” and then adjust the HPF or LPF level.

Setting contents:

-12 to 0 dB (Initial setting: 0)

3Repeat steps 1 to 2 to make adjustment to the other

channels.

4To store the adjusted setting value, touch and hold

[Preset 1], [Preset 2], or [Preset 3] for at least 2 seconds.

• Touch [Flat] to initialize all values.

• If the Rear Speaker setting is “Off,” the Rear Speaker setting cannot be

edited (page 33).

• If the Subwoofer setting is “Off,” the Subwoofer setting cannot be edited

(page 33).

• While adjusting the X-Over you should consider the frequency response

of the connected speakers.

Calling the X-Over adjusted value

Calling the pre-set X-Over adjusted value.

Touch [Preset 1], [Preset 2], or [Preset 3] on the X-Over

screen.

The setting stored in the Preset will be recalled.

Band1: 20 Hz~100 Hz (63 Hz)

Band2: 63 Hz~315 Hz (125 Hz)

Band3: 125 Hz~500 Hz (250 Hz)

Band4: 250 Hz~1 kHz (500 Hz)

Band5: 500 Hz~2 kHz (1 kHz)

Band6: 1 kHz~4 kHz (2 kHz)

Band7: 2 kHz~7.2 kHz (4 kHz)

Band8: 5.8 kHz~12 kHz (8 kHz)

Band9: 9 kHz~20 kHz (16 kHz)

Adjusting the Crossover Settings (X-Over)

Front HPF Rear HPF Subw. LPF Front HPF

36-EN

Before performing the following procedures, see “About Time

Correction” (page 38).

Setting item:

Time Correction

1Touch the Correction mode button.

The pop up screen for selecting the correction mode is

displayed.

2Touch [ms], [cm] or [inch] to select the mode for making

adjustments.

The selected mode is displayed on the Correction mode button.

3Touch [ ] or [ ] for each speaker to adjust the time or

distance.

0.0 msec to 9.9 msec (0.1 msec/step)

0.0 cm (0.0 inch) to 336.6 cm (132.7 inch) (3.4 cm/step)

All speaker setting values are adjustable in the range of 15 ms or 510

cm.

4To store the adjusted setting value, touch and hold

[Preset 1], [Preset 2], or [Preset 3] for at least 2 seconds.

• Touch [Flat] to set all values to 0.0.

• If the Rear Speaker setting is “Off,” the Rear Speaker setting cannot be

edited (page 33).

• If the Subwoofer setting is “Off,” the Subwoofer setting cannot be edited

(page 33).

Calling the Time Correction Value

Calling the pre-set time correction value.

Touch [Preset 1], [Preset 2], or [Preset 3] on the time

correction screen.

The setting stored in the Preset will be recalled.

If Defeat is “On,” MX HD, Equalizer Presets and Dual HD EQ functions

are turned Off. This disables any settings made for these functions.

Setting item:

Defeat

Setting contents:

Off (Initial setting) / On

Setting item:

Source Volume Setup Radio / SiriusXM*1 / Compressed Media*2 /

iPod Music / iPod Video or AUX*3, 4 / HDMI*4, 5 / Bluetooth Audio /

Factory Audio*6

Setting contents:

-14 to +14 (Initial setting: 0)

*1 Not displayed when a SiriusXM Tuner is not connected.

*2 Compressed Media is the music data in a USB flash drive (MP3/

WMA/AAC/FLAC).

*3 The item selected in AUX Source Select (iPod Video or AUX) is

displayed. For details, see “Setting the AUX Mode” (page 44).

*4 The source name set in “HDMI Setup” (page 45) and “Setting the

Auxiliary (AUX) Name” (page 45) is displayed.

*5 Not displayed when an HDMI device is not connected.

*6 Not displayed when an iDataLink module is not connected.

• Settable source differs depending on the connected device and settings.

You can adjust the volume of the incoming call.

Setting item:

Caller Level

Setting contents:

1 to 11 (Initial setting: 5)

You can adjust the transmit volume, during the call.

Setting item:

Microphone Level

Setting contents:

1 to 11 (Initial setting: 5)

You can adjust the receive volume, during the call.

Setting item:

Ring Tone Level

Setting contents:

1 to 6 (Initial setting: 3)

You can change the volume of the sound heard when a button is

touched.

Setting item:

Key Sound Feedback

Setting contents:

0 to 6 (Initial setting: 3)

Adjusting the Time Correction (TCR)

Setting Defeat

Correction mode

Setting the Volume for Each Source

Adjusting the Caller Level

Adjusting the Microphone Level

Adjusting the Ring Tone Level

Volume Setting

37-EN

The sound can be muted when the shift gear lever is set to the reverse

(R) position enabling you to easily hear sensors, etc., while reversing

your car.

Setting item:

Mute While Backing Up

Setting contents:

Off / On (Initial setting)

You can restore the Dual HD EQ*/X-Over*/Time Correction*/MX HD

Level/Rear Speaker/Subwoofer/Subwoofer Level/Subwoofer Phase to

factory settings.

Setting item:

Default Sound Settings

Touch [Set], and the confirmation message appears.

To initialize, touch [OK].

*The setting values that are stored in Preset 1 to Preset 3 cannot be

initialized.

About the Crossover

Crossover (X-Over):

This unit is equipped with an active crossover. The crossover limits the

frequencies delivered to the outputs. Each channel is controlled

independently. Thus, each speaker pair can be driven by the frequencies

for which they have been optimally designed.

The crossover adjusts the HPF (high pass filter) or LPF (low pass filter)

of each band, and also the slope (how fast the filter rolls off the highs or

lows).

Adjustments should be made according to the reproduction

characteristics of the speakers. Depending on the speakers, a passive

network may not be necessary. If you are unsure about this point, please

consult your authorized Alpine dealer.

• HPF (high pass filter): Cuts the lower frequencies and allows the higher

frequencies to pass.

• LPF (low pass filter): Cuts the higher frequencies and allows the lower

frequencies to pass.

• Slope: The level change (in dB) for a frequency change of one octave.

• The higher the slope value, the steeper the slope becomes.

• Adjust the slope to FLAT to bypass the HP or LP filters.

• Do not use a tweeter without the HPF on or set to a low frequency, as it

may cause damage to the speaker due to the low frequency content.

• Adjustment should be made according to the recommended crossover

frequency of the connected speakers. Determine the recommended

crossover frequency of the speakers. Adjusting to a frequency range

outside that recommended may cause damage to the speakers.

For the recommended crossover frequencies of Alpine speakers, refer to

the respective Owner’s Manual.

We are not responsible for damage or malfunction of speakers caused by

using the crossover outside the recommended value.

Setting Audio Mute On/Off while Backing up

Off: Does not mute.

On: Mutes when the shift gear lever is set to the reverse (R)

position.

Default Sound Settings

Cut-off frequency

(1/3 octave steps) Slope Level

HPF LPF HPF LPF

Subwoofer

(LPF) ---- 20 Hz -

200 Hz ----

FLAT, –6,

–12, –18,

–24 dB/oct.

0 to

–12 dB

Rear

speaker

(HPF)

20 Hz -

200 Hz ----

FLAT, –6,

–12, –18,

–24 dB/oct.

---- 0 to

–12 dB

Front

speaker

(HPF)

20 Hz -

200 Hz ----

FLAT, –6,

–12, –18,

–24 dB/oct.

---- 0 to

–12 dB

Level

adjusting

(0 to –12 dB)

Output frequency

range Output frequency range

Slope adjusting

20 Hz

(Different from actual

display) LPF cut-off

frequency

HPF cut-off

frequency

Low range High range

Slope

FLAT

Subwoofer Rear speaker

Front speaker

200 Hz

38-EN

About Time Correction

The distance between the listener and the speakers in a car vary widely

due to the complex speaker placement. This difference in the distances

from the speakers to the listener creates a shift in the sounds image and

frequency characteristics. This is caused by the time delay between the

sound reaching the listener’s right versus the left ear.

To correct this, this unit is able to delay the audio signal to the speakers

closest to the listener. This effectively creates a perception of increased

distance for those speakers. The listener can be placed at an equal

distance between the left and right speakers for optimum staging.

The adjustment will be made for each speaker in 3.4 cm steps.

Adjust the time correction level of the front left speaker to a high value

and the rear right to zero or a low value.

The sound is not balanced because the distance between the listening

position and the various speakers is different.

The difference in distance between the front left speaker and the rear right

speaker is 1.75 m (68-7/8").

Here we calculate the time correction value for the front left speaker in the

diagram on the above.

Conditions:

Farthest Speaker – listening position : 2.25 m (88-9/16")

Front left speaker – listening position : 0.5 m (19-11/16")

Calculation: L = 2.25 m – 0.5 m = 1.75 m (68-7/8")

Time correction = 1.75 ÷ 343* × 1,000 = 5.1 (ms)

*Speed of sound: 343 m/s (765 mph) at 20°C

In other words, giving the front left speaker a time correction value of 5.1

ms makes it seem as if its distance from the listener is the same as the

distance to the farthest speaker.

Time correction eliminates the differences in the time required for the

sound to reach the listening position.

The time of the front left speaker is corrected by 5.1 ms so that its sound

reaches the listening position at the same time as the sound of other

speakers.

Adjust the time correction level of each speaker to almost the same level.

1Sit in the listening position (driver’s seat, etc.) and

measure the distance (in meters) between your head and

the various speakers.

2Calculate the difference between the distance correction

value to the farthest speaker and the other speakers.

L = (distance to farthest speaker) – (distance to other speakers)

These values are the time correction values for the different speakers.

Setting these values to make each sound reach the listening position

at the same time as the sound of other speakers.

Time Correction Value List

Example 1. Listening Position: Front Left Seat

Example 2. Listening Position: All Seats

Time

Difference

(msec)

Distance

(cm)

Distance

(inch)

Time

Difference

(msec)

Distance

(cm)

Distance

(inch)

0.0 0.0 0.0 5.1 173.4 68.3

0.1 3.4 1.3 5.2 176.8 69.7

0.2 6.8 2.7 5.3 180.2 71.0

0.3 10.2 4.0 5.4 183.6 72.4

0.4 13.6 5.4 5.5 187.0 73.7

0.5 17.0 6.7 5.6 190.4 75.0

0.6 20.4 8.0 5.7 193.8 76.4

0.7 23.8 9.4 5.8 197.2 77.7

0.8 27.2 10.7 5.9 200.6 79.1

0.9 30.6 12.1 6.0 204.0 80.4

1.0 34.0 13.4 6.1 207.4 81.7

1.1 37.4 14.7 6.2 210.8 83.1

1.2 40.8 16.1 6.3 214.2 84.4

1.3 44.2 17.4 6.4 217.6 85.8

1.4 47.6 18.8 6.5 221.0 87.1

1.5 51.0 20.1 6.6 224.4 88.4

1.6 54.4 21.4 6.7 227.8 89.8

1.7 57.8 22.8 6.8 231.2 91.1

1.8 61.2 24.1 6.9 234.6 92.5

1.9 64.6 25.5 7.0 238.0 93.8

2.0 68.0 26.8 7.1 241.4 95.1

2.1 71.4 28.1 7.2 244.8 96.5

2.2 74.8 29.5 7.3 248.2 97.8

2.3 78.2 30.8 7.4 251.6 99.2

2.4 81.6 32.2 7.5 255.0 100.5

2.5 85.0 33.5 7.6 258.4 101.8

2.6 88.4 34.8 7.7 261.8 103.2

2.7 91.8 36.2 7.8 265.2 104.5

2.8 95.2 37.5 7.9 268.6 105.9

2.9 98.6 38.9 8.0 272.0 107.2

3.0 102.0 40.2 8.1 275.4 108.5

3.1 105.4 41.5 8.2 278.8 109.9

3.2 108.8 42.9 8.3 282.2 111.2

3.3 112.2 44.2 8.4 285.6 112.6

3.4 115.6 45.6 8.5 289.0 113.9

3.5 119.0 46.9 8.6 292.4 115.2

3.6 122.4 48.2 8.7 295.8 116.6

3.7 125.8 49.6 8.8 299.2 117.9

3.8 129.2 50.9 8.9 302.6 119.3

3.9 132.6 52.3 9.0 306.0 120.6

4.0 136.0 53.6 9.1 309.4 121.9

4.1 139.4 54.9 9.2 312.8 123.3

4.2 142.8 56.3 9.3 316.2 124.6

4.3 146.2 57.6 9.4 319.6 126.0

4.4 149.6 59.0 9.5 323.0 127.3

4.5 153.0 60.3 9.6 326.4 128.6

4.6 156.4 61.6 9.7 329.8 130.0

4.7 159.8 63.0 9.8 333.2 131.3

4.8 163.2 64.3 9.9 336.6 132.7

4.9 166.6 65.7

5.0 170.0 67.0

39-EN

Picture Quality. Setup

[Picture Quality.] is selected on the General Setup Menu screen in step

1. See “General Setup” (page 32).

You can set up items related to an image.

Settable items differ depending on the application.

[Video] (Video media)*1:

Visual EQ / Brightness / Color / Tint / Contrast / Sharpness

[Camera]*2:

Brightness / Color / Contrast

[Navigation]:

Brightness / Contrast

*1 “Video” can be selected while a video is playing.

*2 The camera names are not displayed when “Off ” is set (page 46).

You can select a mode suitable for the subject image.

Setting item:

Visual EQ

Setting contents:

Off (Initial setting) / Night / Soft / Sharp / Contrast

• To return to the default video settings, set this function to Off. Any

Visual EQ selection or changes made are reset their initial settings.

Setting item:

Brightness

Setting content:

-15 to +15 (Initial setting: 0)

You can adjust the brightness between MIN (-15) and MAX (+15).

When it reaches the minimum or maximum point, the display shows

“MIN” or “MAX” respectively.

Setting item:

Color

Setting content:

-15 to +15 (Initial setting: 0)

You can adjust the color between MIN (-15) and MAX (+15). When it

reaches the minimum or maximum point, the display shows “MIN” or

“MAX” respectively.

Setting item:

Tint

Setting content:

R15 to G15 (Initial setting: 0)

Adjust the Color from R15 to G15.

Setting item:

Contrast

Setting content:

-15 to +15 (Initial setting: 0)

You can adjust the contrast between MIN (-15) and MAX (+15). When

it reaches the minimum or maximum point, the display shows “LOW”

or “HIGH” respectively.

Setting item:

Sharpness

Setting content:

-5 to +5 (Initial setting: 0)

Picture quality adjustment range is -5 to +5. “SOFT” and “HARD”

appear as the minimum and maximum values specified.

When adjusting audio (video media), you can store the settings made for

“Adjusting Brightness, Color, Tint, Contrast and Sharpness.”

Setting item:

Preset 1 / Preset 2

1After completing “Adjusting Brightness, Color, Tint,

Contrast and Sharpness” (page 39), touch and hold

[Preset 1] or [Preset 2] to save the settings.

2Touch [Preset 1] or [Preset 2] to call the saved settings.

Selecting the Visual EQ Mode

(Factory’s setting)

Off: Initial Setting

Night: Suitable for movies in which dark scenes frequently

appear.

Soft: Suitable for CGs and animated films.

Sharp: Suitable for old movies where images are not clearly

shown.

Contrast: Suitable for recent movies.

Adjusting Brightness

Adjusting Color of Picture

Adjusting Tint of Picture

Adjusting Image Contrast

Adjusting Picture Quality

Saving and calling the adjusted picture

quality

40-EN

Display/Key Setup

[Display/Key] is selected on the General Setup Menu screen in step 2.

See “General Setup” (page 32).

You can set up the brightness, color, display, etc., of the screen.

1Touch [Screen/Lighting] in the Display/Key Setup Menu

screen.

The Screen/Lighting setup screen appears.

Setting item:

Dimmer / Key Illumination Level / Screen Dimmer Level

Setting the Brightness of the Backlighting

Backlighting is provided by LEDs light built into the liquid crystal panel.

The illumination control adjusts the brightness of the backlighting based

on the car ambient lighting for easier viewing.

Setting item:

Dimmer

Setting contents:

Auto (Initial setting) / On / Off

• When “On” is set, the setting is also applied for the button lighting in

“Adjusting the Dimmer of Button Lighting at Night” (page 40), and

“Adjusting the Minimum Level of Backlight” (page 40).

Adjusting the Dimmer of Button Lighting at Night

You can adjust the brightness of the button lighting at night with the

dimmer.

Setting item:

Key Illumination Level

Setting level:

-2 to +2 (Initial setting: 0)

• This setting is only available when “Dimmer” is set to “On.”

Adjusting the Minimum Level of Backlight

You can adjust the brightness of the backlight. This function could be

used, for instance, to change the screen brightness while traveling at

night.

Setting item:

Screen Dimmer Level

Setting content:

-15 to +15 (Initial setting: 0)

You can adjust the level between MIN (-15) and MAX (+15). When it

reaches the minimum or maximum point, the display shows “MIN” or

“MAX” respectively.

• This setting is only available when “Dimmer” is set to “On.”

You can choose from 8 different display colors.

Setting item:

Screen Color

Setting contents:

Blue (Initial setting) / Light Blue / Aqua / Red / Green / Amber / Yellow /

White

You can choose the color of the Front Panel button from one of 7 colors.

Setting item:

Illumination Color

Setting contents:

Blue (Initial setting) / Light Blue / Aqua / Red / Green / Amber / Yellow

Scroll display is available if folder name, file name or tag information is

entered.

Setting item:

Text Scroll

Setting contents:

Off (Initial setting) / On

You can set the artwork position to the center or the left.

Setting item:

Artwork Position

Setting contents:

Center / Left (Initial setting)

Screen/Lighting Customize

Auto: Adjust the brightness of the background illumination of

the monitor automatically to the brightness of the car

interior.

On: Keep the background illumination of the monitor dark.

Off: Deactivate Auto Dimmer mode to keep the background

illumination of the monitor bright.

Switching the Display Color

Switching the Illumination Color (X108U/INE-

W967HD only)

Setting the Text Scroll

Off: Turns off the scroll mode.

On: Turns on the Auto scroll mode. Scroll display is repeated

as long as the mode is turned on.

Switching the Artwork Position

41-EN

General Setup

[General] is selected on the General Setup Menu screen in step 1. See

“General Setup” (page 32).

You can set up items related to the language, etc.

The Setup menu, feedback information, etc. for this unit can be changed

to appear in the selected language.

Setting item:

Language

Setting contents:

The character code to be used for tag text information displayed on the

screen can be selected from 7 character codes.

Setting item:

Format

Setting contents:

Latin-1 / Latin-9 (Initial setting) / Russian / Chinese / Thai / Arabic / Hebrew

[About] enables you to check the Serial No., Firmware Version, Model

Name, and to initialize various settings.

Displaying the Product Information

You can view the version information of this product. Make note of this

information and refer to it whenever you contact Alpine Tech Support

or an Alpine-authorized dealer.

Setting contents:

Serial No. / Firmware Version / Model Name

Initializing the System

You can initialize all data, to restore the factory settings. Remove the

USB flash drive, etc. from the system before operation

Setting item:

Clear All Settings

1Touch [Reset] of “Clear All Settings.”

2After the confirmation message appears, touch [OK].

The confirmation screen appears again.

3Touch [OK].

The system starts initialization.

• Do not turn on/off the power, change the ignition key position or

remove the screen panel until system restart is completed.

This unit has a Demonstration feature for the display. When you install

and use the unit for the first time, the unit will enter demo mode

automatically. To quit demo mode, set Demo mode to Off.

Setting item:

Demo mode

Setting contents:

Off / On (Initial setting)

• If you perform an operation during the Demo mode, the demonstration

is temporarily stopped.

Vehicle Setup

[Vehicle] is selected on the General Setup Menu screen in step 1. See

“General Setup” (page 32).

Vehicle Setup enables you to check the connection status of Reverse

Lead/Parking Brake Lead.

Setting item:

Installation Status

The Installation check screen is displayed.

Setting the Menu Language

Format settings

Latin-1: ISO 8859-1

Latin-9: ISO 8859-15

Russian: ISO 8859-5

Chinese: GB18030-2005

Thai: CP874

Arabic: CP1256

Hebrew: CP1255

About X110/X108U/INE-W967HD

Setting Demo mode to Off/On

Installation Setup

42-EN

[Source] is selected on the Setup main screen in step 3. See “Setup

Operation” (page 29).

Source Setup Menu screen

*This setting is only available when “AUX” is set to “On” ( ).

1Select the desired item.

2To switch the setting, touch [ ], [ ], [ ], [ ], or mark the

checkboxes “Off” ( ) or “On” ( ).

• If “ ” appears, there is a further hierarchy. Touch the desired

item.

3Touch [ ] to return to the main source screen.

• To return to the previous List screen, touch [ ] or [ ] in the

previous page. For details, see “About Basic Operation for List

Screen” (page 18).

Radio Setup

[Radio] is selected on the Source Setup Menu screen in step 1. See

“Source Setup” (page 42).

This unit can set your preferred tone quality for FM radio source.

Setting item:

FM Tuner Setting

Setting contents:

Normal (Initial setting) / HiFi / Stable

• Noise may be more noticeable when HiFi is set, depending on the

reception status. In this case, the Normal setting is recommended.

During manual tuning, you can select the frequency step for FM analog

radio station searching.

Setting item:

FM Frequency Step

Setting contents:

200kHz (Initial setting) / 100kHz

SiriusXM Setup

[SiriusXM] is selected on the Source Setup Menu screen in step 1. See

“Source Setup” (page @@).

The following operations can be performed to manage the stored Songs,

Artists and Sports Teams information. (To learn about how to store the

information, see “Storing the desired Song/Artist” on page @@ and

“Setting the Favorite Sports Team Alerts” on page @@.)

Source Setup

Radio

FM Tuner Setting

FM Frequency Step

SiriusXM

Alert Setup

Alert

Alert Delete All

Favorite Team Setup

Parent Lock

Signal Indicator

AUX

AUX Source Select*

AUX Name*

Signal*

HDMI

Bluetooth Pandora

The following steps 1 to 3 are common to each “Setting

item” of Source Setup. See each section for details.

Setting the TUNER (FM) Tone Quality (Tuner

Condition)

Normal: Standard setting

HiFi: High-quality setting

Stable: Control noise

Setting the TUNER (FM) Frequency Step

43-EN

This menu option allows you to enable the Artist/Song/Team alert for

individual Artists/Songs/Teams (On or Off) or to delete individual

stored Artist/Song/Team alerts (Delete).

Setting item:

Alert Setup

Setting contents:

On / Off / Delete

Set to “On” ( ) to enable the alert for the Artist/Song or Team.

Set to “Off” ( ) to disable the alert for the Artist/Song or Team.

• To delete the list, touch [ ] (Delete), and then touch [OK].

This menu option allows you to temporarily disable the Artist/Song/

Game Alerts for all Artists/Songs/Games. When the Alerts are re-

enabled, individual Artist/Song/Game Alert disabled in the Alert List

menu setting remain disabled.

Setting item:

Alert

Setting contents:

On / Off

If “On” ( ) is set, the alert for all stored Artists/Songs/Games is

enabled.

If “Off” ( ) is set, the alerts for all stored Artists/Songs/Games are

disabled.

This operation will delete all alerts (artists, songs and teams) stored in

memory.

Setting item:

Alert Delete All

1Touch [Reset] of “Alert Delete All.”

A message is displayed.

2Touch [OK] to clear the information of all stored Artist,

Song, and Game alert items.

Touch [Cancel] to cancel.

This menu option allows you to select your favorite teams, organized by

leagues, so that you will be alerted later when your favorite teams are

playing on other channels. Once selected, you will be alerted when

games that those teams are playing in can be heard on a SiriusXM

channel.

Setting item:

Favorite Team Setup

Setting contents:

On / Off

1Touch [Favorite Team Setup].

A sports league list is displayed.

2Select the desired league.

The display changes to the team list of the selected league.

3Touch the checkbox of your Favorite Team to set it to

“On” ( ) or “Off” ( ).

• When “On” ( ) is set, scrolling text of the Team name, Total

registrations, and Remaining number of registration slots is

displayed for two seconds, then the team is registered as a Favorite

Team.

When “Off” ( ) is set, the registration of your Favorite Team is

canceled.

• The maximum number of registered Teams, Artists, and Songs is

50. For details on how to register an Artist alert or Song alert, see

“Storing the desired Song/Artist” (page @@).

• If the total number of registered Teams, Artists, and Songs is

already at 50 when “On” ( ) is set, then scrolling text is

displayed, asking whether you want to replace a registered Artist/

Song/Team with the new one. If you want to replace one, go to step

4Touch [OK].

The list of registered Artists/Songs/Teams is displayed.

• If you want to cancel the registration of your Favorite Team, then

touch [Cancel], and return to step 3.

5Touch the Artist, Song, or Team name that you want to

replace.

Scrolling text of the Team name, Total registrations, and

Remaining number of registration slots is displayed for 2

seconds, then the team is registered as a Favorite Team.

• For details on deleting a registered Artist, Song, or Team beforehand, to

secure a registration slot in advance, see “Setting the Alert individually

for an Artist/Song/Sport Team” (page @@).

You can lock out channels with passcode protection. Channels that are

locked cannot be accessed without entering the passcode. You can

unlock a channel or change the passcode using this menu option.

Setting item:

Parental Lock

1Touch [Parental Lock].

A passcode input screen is displayed.

2Touch the numeric keypad to input a 4-digit passcode.

The initial default 4-digit passcode is set to 0000.

After entering the digit, it is displayed as “*” (asterisk).

• Touch [ ] to delete an entered number.

• Touch [Delete All] to delete all entered numbers.

3Touch [Enter].

Setting the Alert individually for an Artist/

Song/Favorite Team

Setting ON/OFF of all Songs/Artists/Games

Alert

Deleting all stored Alert

Setting the Favorite Sports Team Alerts

Setting the Parental Lock

44-EN

Setting the Lock status of individual channels

4Touch [Locked Channels].

The channels list screen is displayed.

5Touch the checkboxes [ ] or [ ] of the channels list to

set the Parent Lock Off/On.

Clearing the Lock of ALL the locked Channels

4Touch [Clear All Locked Channels].

5Touch [OK] to clear the lock of all the locked channels.

Touch [Cancel] to cancel.

Changing the Lock Passcode

4Touch [Edit Code].

The numeric keypad screen is displayed.

5Use the keypad to enter the current (old) 4-digit

passcode.

The initial passcode is set to 0000.

• Touch [ ] to delete an entered number.

• Touch [Delete All] to delete all entered numbers.

6Touch [Enter] to confirm the entry.

7Now use the keypad to enter the new 4-digit passcode.

8Touch [Enter].

9Then use the keypad to enter the new 4-digit passcode a

second time to verify it.

• Remember to keep a note of the passcode in a safe place in case you

forget the code.

While listening to a SiriusXM Channel, the Signal strength of the

current channel will be displayed.

Setting item:

Signal Indicator

This menu item displays the SiriusXM signal strength as Strong, Good,

Weak or No Signal.

• If the Signal Indicator reports Weak or No Signal and your vehicle is

parked outside with no obstructions to the southern sky, then your

SiriusXM antenna may not be properly installed or may have become

damaged.

AUX Setup

[AUX] is selected on the Source Setup Menu screen in step 1. See

“Source Setup” (page 42).

You can set up the items related to the Auxiliary device.

Setting item:

AUX

Setting contents:

Off / On (Initial setting)

Make sure the AUX is set to “On” ( ). See “AUX Setup” (page 44).

Connection with external input devices is available through the AUX

Input connector. An optional adapter cable is required (standard RCA to

3.5ø mini-phono plug or 3.5ø to 3.5ø mini phono plug).

You can also play back video connecting with an optional AV cable

(4-pole mini AV plug to 3-RCA).

Setting item:

AUX Source Select

Setting contents:

iPod Video / AUX (Initial setting)

• When an iPod video is selected or the current source is AUX, this setting

cannot be adjusted.

Usable 4-pole mini AV plug

The unit accepts the following 4-pole mini AV plug pin-out:

• Please check pin-out carefully before use of this product. Depending on

the cable, there may be no picture and/or sound.

Signal Strength Information

Off: AUX source is not displayed.

On: AUX source is displayed.

Setting the AUX Mode

iPod Video: Set when connected to an iPod or iPhone.

AUX: Set when connected to an external input device.

Audio L (White)

Audio R (Red)

Ground

Video (Yellow)

45-EN

Make sure the AUX is set to “On” ( ). See “AUX Setup” (page 44).

Setting item:

AUX Name

Setting contents:

AUX (Initial setting) / AUX DVD / GAME / External DVD / DVD Changer /

DVB-T / TV / USB Player

You can make this setting only when AUX is set to “On” ( ). See “AUX

Setup” (page 44).

Setting item:

Signal

Setting contents:

Auto (Initial setting) / NTSC/PAL

HDMI Setup

[HDMI] is selected on the Source Setup Menu screen in step 1. See

“Source Setup” (page 42).

You can set the name of an external device connected via HDMI.

Setting item:

HDMI

Setting contents:

HDMI (HDMI 1*) (Initial setting) / DVD

*When the HDMI selector is set to “On,” “HDMI 1” is displayed in the

Setting contents. For details on setting the HDMI selector, see “Setting

the HDMI selector On/Off ” (page @@).

Setting the Bluetooth Pandora®

[Bluetooth Pandora] is selected on the Source Setup Menu screen in

step 1. See “Source Setup” (page @@).

To use Bluetooth Pandora, set the Bluetooth Pandora setting to “On.”

Setting item:

Bluetooth Pandora

Setting contents:

Off / On (Initial Setting)

• When “On” is set, the Bluetooth Pandora® source is displayed on the

Menu screen.

• When the current source is Bluetooth Pandora, this setting cannot be

adjusted.

[System] is selected on the Setup main screen in step 3. See “Setup

Operation” (page 29).

System Setup Menu screen

*1 When Camera Select is set to “Off,” you cannot select this item.

*2 You can select this item only when Camera Select is “Front” or “Rear.”

*3 You can select this item only when Camera Select is “Rear.”

*4 Not displayed when you select “Camera Selector” in Camera Select.

*5 Displayed when you select “Camera Selector” in Camera Select.

*6 You can change the Default Camera only when you set more than one

camera among Front Camera/Rear Camera/Side Camera to “On.” For

details, see “Default Camera setting” (page @@).

*7 Set this setting after closing the Alpine TuneIt App.

1Select the desired item.

2To switch the setting, touch [ ], [ ], [ ], [ ], or mark the

checkboxes “Off” ( ) or “On” ( ).

• If “ ” appears, there is a further hierarchy. Touch the desired

item.

Setting the Auxiliary (AUX) Name

Switching the Visual Input Signal System

Auto: The video input signal type (NTSC or PAL) will be

automatically selected.

NTSC/PAL: Choose the video input signal type manually.

HDMI

(HDMI 1):

Set when a smartphone is connected via HDMI.

DVD: Set when an external DVD player is connected.

System Setup

Camera

Camera Select

Camera Signal*1, 4

Guide Adjustment*2, 4

Camera Interrupt (Power Mode)*3, 4

Front Camera / Rear Camera / Side Camera*5

Default Camera*6

Factory System Setup

USB/iPod / SiriusXM / Bluetooth Audio

Hands-free Connection

Default Vehicle Screen

Maestro Module

Rear Seat Entertainment

Remote Sensor

External Accessories

External Audio Processor

RSE Aux Switch Box

HDMI selector

External Accessory Ctrl

Smartphone Apps

Alpine TuneIt App*7

The following steps 1 to 3 are common to each “Setting

item” of System Setup. See each section for details.

46-EN

3Touch [ ] to return to the main source screen.

• To return to the previous List screen, touch [ ] or [ ] in the

previous page. For details, see “About Basic Operation for List

Screen” (page 18).

Camera Setup

[Camera] is selected on the System Setup Menu screen in step 1. See

“System Setup” (page 45).

You can set up items related to the Camera.

Setting item:

Camera Select

Setting contents:

Off (Initial setting) / Front / Rear / Other / Camera Selector

*When selecting Camera Selector, you can set the Front Camera/Rear

Camera/Side Camera to On/Off. For details, see “Setting Multi Camera

to On/Off” (Page@@).

When the camera is connected, the video input signal type can be

chosen.

Further setting item:

Camera Signal

Setting contents:

NTSC (Initial setting) / PAL

The video pattern can be changed when connected to Multi View

Camera.

When Camera Select is set to “Off,” you cannot select this item.

Setting item:

Guide Adjustment

1Touch [Guide Adjustment].

The camera guide adjustment screen is displayed.

Multi View compatible Side Camera

2Touch [Front] or [Rear].

The camera guide adjustment screen is displayed.

Multi View compatible Front Camera/Rear Camera

2Touch [Back], [Panorama], [Corner], or [Top].

The view will change to the selected view.

•[Back] will not appear for the Front camera.

• For an explanation of video patterns, see the camera Owner’s Manual.

You can adjust the camera guide position.

Setting item:

Guide Adjustment

1Touch [Guide Adjustment].

The camera guide adjustment screen is displayed.

• If the video pattern is set to “Corner (Rear/Front Camera only),”

the camera guide will not be displayed.

• When you connect a Multi View compatible camera, select a

Video Pattern to make a guide adjustment.

• When you connect a Multi View compatible Side Camera, after

selecting the Video Pattern, touch [ ] (Left steering) or

[ ] (Right steering) to make the guide adjustment that

matches the position of the steering wheel in your vehicle.

2Touch [Adjust].

• If [Adjust] does not appear, proceed to step 3.

3Touch the guide you intend to adjust.

Guide line can also be selected by touching [ ] [ ].

Rear Camera screen example

When Hitch Guide is set to Off

• You cannot adjust the position of the yellow guide line “ ” in

the center independently.

It is controlled by a system to be the center of the two yellow guide

lines “ ” and “ ” on the left and right, or the central green

line “ ” and red guide line “ ”.

When Hitch Guide is set to On

• You can adjust the Hitch Guide to mark the position of the junction

between your vehicle and your trailer.

Setting the Camera Input

Front: Front camera

Rear: Rear camera

Other: Side camera, Room camera, etc.

Camera

Selector*:

Front Camera/Rear Camera/Side Camera connected to

the optional Multi Camera Interface box.

Setting the Camera Signal Input

Switching Video Patterns for Multi View

Camera

Adjusting the Rear/Front/Side Camera Guide

47-EN

Front Camera screen example

Side Camera screen example

4Touch [ ], [ ], [ ] or [ ] to adjust the position of the

guide.

• Touching [Clear] clears adjustments and returns to the setting

before guide line alteration.

5After the adjustment is completed, touch [Set].

Adjusting Guides Simultaneously (for Rear/Side Camera

only)

1Touch [Link].

The 3 vertical guides of the currently-selected guide link

together, allowing them to be adjusted simultaneously.

• Note on the yellow guide line “ ” in the center

The yellow guide line “ ” in the center is controlled by a system that

locates it in the center of the two yellow guide lines, “ ” and “ ”

on the left and right, or the green line “ ” on the top and red guide

line “ ” below. Therefore you cannot move it manually.

1Touch [Link].

The 2 vertical guides of the currently-selected guide link

together, allowing them to be adjusted simultaneously.

Turning Guide Display On/Off (Rear/Front Camera only)

Turning the selected guide off.

1Touch [On/Off].

The currently selected guide will turn off.

2To turn the guide on, touch [On/Off] again.

• Guides that are turned off are still adjustable.

Returning Guides to Default

1Touch [Default].

A message window will appear.

2Touch [OK].

Adjusted values will return to default settings.

You can set whether to display the rear camera image when the gear

lever is moved to the reverse (R) position while the unit is turned off.

You can select this item only when Camera Select is “Rear.”

Setting item:

Camera Interrupt (Power Mode)

Setting contents:

On (Initial setting) / Off

When connecting the optional Multi Camera Interface box, you can

connect up to 3 cameras as Front Camera/Rear Camera/Side Camera.

Set to “On” ( ) to enable each camera.

Setting item:

Front Camera / Rear Camera / Side Camera

Setting contents:

Off (Initial setting) / On

Set to “On” and touch the camera name to make individual

adjustments.

Camera Interrupt Setting (Power OFF Mode)

(Rear Camera Only)

On: The rear camera image is displayed

Off: The rear camera image is not displayed

Setting Multi Camera to On/Off

Camera

Signal:

See “Setting the Camera Signal Input” (page @@)

Guide

Adjustment:

See “Setting the Camera Signal Input” (page @@)

Camera

Interrupt

(Power Mode):

See “Camera Interrupt Setting (Power OFF Mode)” (page

@@)

48-EN

Setting a Default Camera

When connecting an optional Multi View Camera, you can set which

camera image is displayed when you touch the Camera button on the

Menu screen or press the (CAMERA) button (X110 only).

Setting item:

Default Camera

Setting contents:

Front / Rear / Side

• The initial setting differs depending on the cameras set to “On” in

“Setting Multi Camera to On/Off.”

Factory System Setup

[Factory System Setup] is selected on the System Setup Menu screen in

step 1. See “System Setup” (page @@).

You can make this setting only when an iDataLink module is connected.

You can set whether the following source icon in the Menu screen is

available.

Setting item:

USB/iPod (Initial setting: Both) / SiriusXM (Initial setting: Aftermarket) /

Bluetooth Audio (Initial setting: Aftermarket)

Setting contents:

Both / OEM / Aftermarket

*USB/iPod only.

• The iDataLink source icons not displayed on the Menu screen when no

iDataLink module is connected even though “Both” or “OEM” is set.

• You cannot set the source that is currently being played.

Select to pair the Bluetooth compatible phone with this unit or the

connected iDataLink module.

Setting item:

Hands-free Connection

Setting contents:

OEM / Aftermarket (Initial setting)

• When “OEM” is selected, the screen changes to the Phone menu screen

of the iDataLink module.

Press and hold the (Favorite) button for at least 2 seconds or touch

the Menu screen (page @@) to display the Info mode screen, and then

set the following.

Setting item:

Default Vehicle Screen

Setting contents:

Climate / Vehicle Info. / Gauges / Parking Assist / Last mode (Initial setting)

• Depending on the car, some setting contents or this setting item may not

be displayed.

You can change the setting of the connected iDataLink module.

Setting item:

Maestro Module

• Depending on the iDataLink module, the setting contents may differ.

Rear Seat Entertainment Setup

[Rear Seat Entertainment] is selected on the System Setup Menu screen

in step 1. See “System Setup” (page 45).

When a Rear monitor equipped with HDMI input is connected to this

unit, change this setting to “On.” You can output images to the Rear

monitor. For details, see “Rear Seat Entertainment Function” (page 20).

Setting item:

Rear Seat Entertainment

Setting contents:

Off (Initial setting) / On

• When this setting is “On,” you can use this unit to switch the

Illumination of a Rear monitor with the Illumination function.

Setting the Rear Seat Entertainment System

Make sure the Rear Seat Entertainment is set to “On” ( ). See “Rear

Seat Entertainment Setup” (page 48).

Setting item:

Plasmacluster/Illumination Color

Setting contents:

Off (Initial setting) / On

• For details on adjusting Plasmacluster/Illumination, see “Rear Seat

Entertainment Function” (page 20).

• When the Rear Seat Entertainment setting is set to “Off,” you cannot

select this item.

• Set the coordination color and Plasmacluster controls on the Rear

monitor to “Navi.” When set to “Rear monitor,” you cannot operate

them from this unit.

Setting the Source Category

Both*: Both the sources listed above from this unit and

iDataLink module are available.

OEM: Only the source listed above from iDataLink module is

available.

Aftermarket: Only the source listed above from this unit is available.

Setting the Hands-free Connection

OEM: Select to pair the Bluetooth compatible phone with the

connected iDataLink module.

Aftermarket: Select to pair the Bluetooth compatible phone with this

unit.

Setting the Default Vehicle Screen

Setting the Maestro Module

49-EN

Make sure the Rear Seat Entertainment is set to “On” ( ). See “Rear

Seat Entertainment Setup” (page 48).

For remote control operation, the remote sensor of the external device

(Rear monitor, etc.) can be switched, as you prefer.

Setting item:

Remote Sensor

Setting contents:

Front (Initial setting) / Rear

• You can also control this setting from the Rear Seat Entertainment

System Setup screen. For details, see “Rear Seat Entertainment

Function” (page 20).

External Accessories Setup

[External Accessories] is selected on the System Setup Menu screen in

step 1. See “System Setup” (page 45).

When using an external audio processor, set to “On” ( ).

Setting item:

External Audio Processor

Setting contents:

Off (Initial setting) / On

• When this setting is “On,” the Volume level is fixed at 10. Also, Balance/

Fader/Subwoofer Level/Subwoofer Phase/Bass/Treble/MX HD/EQ

Presets/Dual HD EQ/X-Over/Time Correction/Defeat/Phone Speaker/

Default Sound Settings are set to “Off ” or “Flat” and cannot be

adjusted.

• Use the external AP to adjust volume.

When displaying an AUX image in the rear monitor, you need an

external AUX distribution box.

When using an external AUX distribution box, set to “On” ( ).

Setting item:

RSE Aux Switch Box

Setting contents:

Off (Initial setting) / On

If you connect an HDMI selector, you can connect two HDMI devices.

When using an HDMI selector, set to “On” ( ).

Setting item:

HDMI selector

Setting contents:

Off (Initial setting) / On

• For details on switching the HDMI source when two HDMI devices are

connected, see “HDMI Operation” (page @@).

When you have connected the optional External Accessory Control box,

set this setting to “On” to turn the headlights ON/OFF or adjust the air

suspension from this unit.

Setting item:

External Accessory Ctrl

Setting contents:

Off (Initial setting) / On

• When set to “On,” the [##] (Ext Acc Ctrl) icon is displayed on the Menu

screen.

• For details on the External Accessory screen and its operation, see

“External Accessory Control Operation” (page @@).

Remote Sensor Setting

Front: The remote sensor of this unit is effective.

Rear: The remote sensor of Rear monitor is effective.

Setting the External Audio Processor

Setting the Additional AUX BOX

Setting the HDMI Selector On/Off

Setting the External Accessory Control

50-EN

Smartphone Apps Setup

[Smartphone Apps] is selected on the System Setup Menu screen in step

1. See “System Setup” (page 45).

Set TuneIt to USB (iPhone) when an iPhone is connected, or set to

Bluetooth (Android) when an Android Smartphone is paired.

Setting item:

Alpine TuneIt App

Setting contents:

Off / USB (iPhone) (Initial setting) / Bluetooth (Android)*

• Set this setting after closing the Alpine TuneIt App.

• For this function to work properly, specific applications must be

installed on your Smartphone before connection. Consult your Alpine

dealer or the Alpine website for details.

• Only the iPhone and certain Android Smartphones support this

function.

*Not displayed when Bluetooth is set to Off. For details, see “Bluetooth

Setup” (page 30)

Off: No Smartphone is connected.

USB (iPhone): When an iPhone is connected to the unit’s USB port, you

can programme the unit’s sound tuning parameters, or

communicate with SNS.

Bluetooth

(Android):

Set this when an Android Smartphone is paired with this

unit via Bluetooth technology. And after Bluetooth

Audio is connected, you can programme the unit’s

sound tuning parameters, or communicate with SNS.

51-EN

The unit can receive HD Radio signals based on digital radio broadcast

standards, in addition to analog radio broadcasts using RBDS.

HD Radio signals are broadcast in the service areas of the current AM/

FM broadcasters where they provide digital audio distribution and data

services. This unit receives the above digital broadcasts for your high-

quality sound enjoyment.

Depending on the signal strength in TUNER mode, the unit will

automatically switch between digital signals if they can be received, and

analog radio using RBDS if digital signals cannot be received. For

details, please see “Switching between Digital and Analog,” “Forced

Analog Mode.”

• RBDS mode is only available during FM broadcast reception.

This unit is able to receive signals based on the terrestrial digital radio

broadcasting standard.

When current AM/FM broadcasters are transmitting digital audio and

data services, HD Radio signals are on-the-air in their service area. You

can receive their digital broadcast and enjoy high quality sound.

If there is no HD Radio signal in the current area, after 10 seconds, this

unit will switch to receive the RBDS Radio signal automatically.

However, the display is still HD Radio mode screen.

HD Radio main screen example

Function mode

HD Radio Indicator *1

Band display

Displays the band of the signal currently being received.

Tag Indicator

When Tagging is available, the Tag indicator is shown.

Multicast Indicator*2

Lights during multicast reception.

Info area

RBDS

Station Info. mode:

PTY/Frequency or PS Name/Artist Name/Song Name/Album

Name

Radio Text mode:

Frequency/ Radio Text

• For details on switching the display of the Radio text, see

“Displaying Radio Text (RBDS FM Radio mode only)” (page @@).

HD Radio

Station Info. mode:

Station Slogan or Long Station Name/Frequency/Artist

Name/Song Name/Album Name

Artwork etc./Station Logo display*1

Preset mode button

Swipe to the right when you use the Preset mode screen.

*1 HD Radio mode only.

*2 Lights during multicast reception.

Preset mode screen example

Preset button

Swipe vertically in the list to change pages.

PTY list button (RBDS FM Radio mode only)

Swipe to the right when you use the PTY list screen.

Radio/HD Radio™/

RBDS

52-EN

Listening to the Radio

1Press the (AUDIO) button to select radio mode.

The display shows the radio mode screen.

• You can select and change the source from the Menu screen

(page 21) or the Favorite screen (page 24).

2Touch [ ].

The radio band select pop up screen is displayed.

•[ ] button displays the current selected band. (e.g. [FM1])

3Select the desired band from FM1/FM2/AM.

4Touch [ ].

The tuning mode selection popup is displayed.

•[ ] button displays the current selected mode. (e.g. [DX Seek])

5Touch the desired tuning mode.

The radio frequency up or down button changes depending on

the tuning mode.

• There are two modes you can select for auto tuning, DX and Local:

- DX Seek (Distance) mode*;

Both strong and weak stations will be tuned in.

- Local Seek mode*;

Only strong stations will be tuned in.

The initial setting is DX.

- D (Digital).DX Seek mode;

Automatically receives a receivable digital broadcast.

- D (Digital).Local Seek mode;

Automatically receives a strong digital broadcast only.

- Manual mode;

The frequency is manually tuned in steps

- PTY Seek mode (RBDS FM Radio mode only);

The currently selected programme type station will be tuned.

• During Forced Analog mode, digital broadcasts cannot be

received.

*Depending on the signal, a digital or analog broadcast is received.

6Touch [ ], [ ] or [ ], [ ] to change the radio

frequency up or down respectively.

In manual mode, touch and hold to change the frequency

continuously.

• The , buttons provide the same functions above.

Presetting Stations Manually

1Tune in a desired radio station you wish to store in the

preset memory by manual or automatic seek tuning.

2Touch the Preset number you want to store, for at least 2

seconds.

The selected station is stored.

3Repeat the procedure to store up to 11 other stations

onto the same band.

To use this procedure for other bands, simply select the desired

band and repeat the procedure.

A total of 36 stations can be stored in the preset memory

(12 stations for each band; FM1, FM2, or AM).

• For details on switching to the Preset mode screen, see in “Radio

main screen example” (page @@).

• If a preset memory has already been set in the same preset number, it

will be cleared and the new station will be memorized.

Presetting Stations Automatically

The tuner can automatically seek and store 12 strong stations in the

selected band in order of signal strength.

Select the desired band then touch and hold [ ] (Auto

Memory).

The tuner automatically seeks and stores 12 strong stations into the

preset buttons in order of signal strength.

When automatic storing has completed, the station stored in the

preset 1 is selected.

• If no stations are stored, the tuner will return to the original station you

were listening to before the automatic storing procedure began.

• You can cancel this process by touching [ ] (Auto Memory) while

the tuner is automatically seeking stations. Canceling will return the

tuner preset to the previous setting.

Tuning to Preset Stations

You can tune in the preset stations in memory on either band using its

preset number.

1Touch [ ].

The radio band select pop up screen is displayed.

•[ ] button displays the current selected band. (e.g. [FM1])

2Select the desired band from FM1/FM2/AM.

3Touch any one of the Preset numbers you have already

stored in the Preset mode screen.

The preset station is received.

• For details on switching to the Preset mode screen, see in “Radio

main screen example” (page @@).

Radio Basic Operation

DX Seek Local Seek D.DX Seek D.Local Seek

Manual PTY

53-EN

Inputting Frequency Directly and Receiving the

Radio Station

You can input a frequency of the same band directly and receive the

radio station.

1Touch [ ] (Direct Tune).

The numeric keypad input mode screen appears.

2Touch a desired number.

Touch [ ] to delete an entered number.

Touch [Delete All] to delete all entered numbers.

3Touch [Enter] on the numeric keypad mode screen to

confirm your selection.

Touch [ ] to hide the keypad display.

Receiving a Multicast (HD Radio Mode only)

Multicasting is the ability to broadcast multiple program streams over a

single FM frequency. This increases the amount and diversity of content

choices. A maximum of 8 multicast station channels can be selected on

this unit.

• “Multicast” indicator appears when signal reception is possible.

• The station number of the current broadcast station appears behind the

frequency (ex. 90.3 MHz-HD5 means there are 5 stations on

90.3 MHz).

Touch [ ] or [ ].

The sub channel of the received radio station is changed.

• If reception is lost during SPS broadcasting due to weak or no signal, the

screen will display “HDx Signal loss.”

Selecting the Receivable PTY (RBDS FM Radio

mode only)

You can select and receive the currently receivable stations in the PTY

list screen.

PTY list screen example

• For details on switching to the PTY list screen, see in “Preset

mode screen example” (page 51).

Select the desired programme type in the PTY list screen.

PTY Seek starts and the receivable programme type is received.

If no PTY station is found, “No PTY.” will be displayed.

• Touch [ ] or [ ] to select the same programme type station as the

currently selected programme type after switching the tuning mode to

PTY (PTY Seek) mode.

Forced Analog Mode

Activate the Compulsory Analog Radio mode to receive only analog

radio signals.

Touch [ ] (Analog).

The [ ] (Analog) button is highlighted. To cancel Compulsory

Analog Radio mode, touch [ ] (Analog) again.

• During Forced Analog mode, only analog broadcasts will be received

even when digital broadcasts become available.

• While Digital is receiving, the “HD” indicator is displayed.

Displaying Radio Text (RBDS FM Radio mode

only)

Text messages from a radio station can be displayed.

1Tune in a radio station that transmits text messages.

2Touch [ ] (Info) in the FM radio mode repeatedly to

switch to the desired display.

Station Info.Mode Radio Text Mode Station Info.Mode

Station Info. Mode

PTY/Frequency or PS/Artist Name/Song Name/Album Name

Radio Text Mode

Frequency/Radio Text

54-EN

Using Ballgame Mode

In live broadcast, such as sportscasts, etc., a time lag occurs between

digital sound and analog sound. Therefore, when live broadcasts are

received, a time lag between the real broadcast may occur and the unit

can change to analog broadcasting automatically.

Touch [ ] (Live) to switch On/Off.

The LIVE Indicator is displayed when Ballgame Mode is set to “On.”

• When receiving a live broadcast while the Ballgame mode is on, the

LIVE indicator is highlighted.

(During live broadcast)

Storing the tag information (HD Radio Mode

only)

iTunes Tagging lets you tag songs heard on HD Radio FM stations. You

can preview, buy and download later, songs from your iTunes tagged

playlist the next time you sync your iPod/iPhone. If the unit is

connected to a Tagging compatible iPod/iPhone, you can use the iTunes

Tagging function. For details, refer to the Owner’s Manual of the

Tagging compatible iPod/iPhone.

When Tagging is available, the “Tag” indicator is shown.

When a desired song is heard on an HD Radio station, touch

[ ] (Tag) to save its tag information.

• The [ ] (Tag) button can be selected only when Tagging is available.

If no iPod/iPhone is connected, “Tag Count X” is displayed (X is the

total amount of the tag information stored in this unit).

• During tagging, the iPod/iPhone takes priority to save the tag

information. If no iPod/iPhone is connected, the tag information is

saved to this unit.

• When the memory of iPod/iPhone is full, “iPod memory full.” is

displayed. The tag information will be stored to the unit.

• If the tagging operation is interrupted by a hands-free phone call, the

tagging operation will be canceled and the unit will display “Cannot

Tag”.

• This unit can store up to 50 tagged songs. When the memory of the unit

is full, “Tag count 50. Tuner memory full. Connect iPod.” may be

displayed.

• When the iPod/iPhone is disconnected from the unit during tagging, its

tag information will be stored in the unit.

• If there is stored tag information on the unit, when an iPod/iPhone

supporting the tag function is connected, the stored tag information will

be transferred to the iPod/iPhone automatically. When the iPod/iPhone

memory becomes full, “iPod memory full.” will be displayed, and any

remaining tag information on the unit will not be transferred to the

iPod/iPhone.

• If tag information already exists, “Already Tagged” will be displayed

when you try to tag information again.

About the Feature Logos

• Digital, CD-quality sound. HD Radio Technology enables local

radio stations to broadcast a clean digital signal. AM sounds like

today’s FM and FM sounds like a CD.

• Program Service Data: Contributes to the superior user

experience of HD Radio Technology. Presents song name, artist,

station IDs, HD2/HD3 Channel Guide, and other relevant data

streams.

• Adjacent to traditional main stations are extra local FM channels.

These HD2/HD3 Channels provide new, original music as well as

deep cuts into traditional genre.

• iTunes® Tagging provides you the opportunity to discover a wide

range of content and the means to “tag” that content for later

review and purchase from the iTunes® Store.

• Visual information related to content being played on your HD

Radio receiver, such as Album Art, historical photographs, still

art from live broadcasts, among other related content.

LIVE Indicator

Tag Indicator

55-EN

You can play back music files (MP3/WMA/AAC/FLAC) stored in a USB

flash drive on the internal player of this system.

USB Audio main screen example

Function mode

Artwork display

• You can change the artwork position. For details, see “Switching

the Artwork Position” (page 40).

Current track no./Total song no.

Artist title

Song title

Album title

Elapsed time

Quick Search button

Touch or swipe to the right to use the Quick Search mode.

Quick Search mode screen example

Swipe vertically in the list to change pages.

Full Search mode button

Swipe to the right when you use the Full Search mode screen.

Playback

1Press the (AUDIO) button to select USB mode.

The display shows the USB mode screen.

• You can select and change the source in the Menu screen (page 21)

or Favorite screen (page 24).

2Touch [ ] or [ ] or to select the desired track (file).

Returning to the beginning of the current (or previous) track (file):

Touch [ ].

Fast reverse :

Touch and hold [ ].

Advancing to the beginning of the next track (file) :

Touch [ ].

Fast forward :

Touch and hold [ ].

• The , buttons provide the same functions above.

3To pause playback, touch [/].

Touching [ / ] again will resume playback.

During playback, the [ ] indicator is displayed in Audio main

screen. During a pause, the [ ] indicator is displayed in the

Audio main screen.

• The playback time may not be correctly displayed when a VBR

(Variable Bit Rate) recorded file is played back.

• If there is tag information, artist name/album name/track name is

displayed.

• ID3 tag/WMA tag

If an MP3/WMA/AAC/FLAC file contains ID3 tag/WMA tag

information, the ID3 tag/WMA tag information is displayed. (e.g., song

name, artist name, and album name)

Repeat Play

1Touch [ ].

The Repeat mode select pop up screen is displayed.

• The [ ] button displays the currently selected mode.

2Select your desired Repeat mode.

USB Flash drive

(Optional)

Folder : Only files in a folder are repeatedly played back.

File : Only the file currently playing is repeatedly played back.

OFF : Repeat mode Off.

56-EN

Random Play

1Touch [ ].

The Random Play mode select pop up screen is displayed.

• The [ ] button displays the currently selected mode.

2Select your desired Random Play mode.

• If the Random Play mode is activated during Repeat playback, the

Repeat Play mode will be canceled.

• If you select a track by using the search mode, the Random Play mode

will be canceled.

Searching for a Desired Song

You can search for your desired song by using one of two modes; the

Quick Search mode and the Full Search mode.

Quick Search mode

Touch your desired Folder name or File name.

The selected Folder*1 or File is played.

*1 The first file in the selected folder is played back.

• For details on switching to the Quick Search mode, see in “USB

Audio main screen example” (page 55).

Full Search mode

Touch your desired Folder name*2 or File name.

When you select a File name, the selected song is played.

When you select a Folder name, repeat the same procedure to select

another Folder name or File name.

*2 When you touch the [ ] by a Folder name, the unit plays from the first

song in the Folder.

• For details on switching to the Full Search mode, see in “Quick

Search mode screen example” (page 55).

• To switch the displayed list or return to the previous page in the Full

Search mode, see “About Basic Operation for List Screen” (page 18).

ALL : All songs in the USB flash drive are played back in

random sequence. Any one song does not play back

again until all songs have been played back.

Folder : A Folder is selected randomly and songs in the Folder

are played back in order. After all songs are played in a

Folder, the next Folder is selected randomly.

OFF : Random mode Off.

57-EN

A separately sold USB iPod/iPhone AV cable (KCU-461iV) or a

separately sold Lightning to USB cable (KCU-471i) is required

depending on the type of iPod/iPhone.

When the unit is connected by the above cable, the controls on the iPod

are disabled.

• This unit does not support video playback from iPhone 5, etc., which

uses Apple’s Lightning Connector.

• Internet or telephone functions, etc., of the iPhone or iPod touch are not

controllable from the unit, but these functions can be controlled using

the iPhone or iPod touch itself.

• To watch the video screen of the file in the iPod/iPhone, the parking

brake must be engaged.

• For automatic transmission vehicles, place the transmission lever in the

Park position.

About iPod/iPhone models usable with this unit

• The following devices have been tested and shown to work with

this unit. Correct function of earlier versions cannot be

guaranteed.

iPod touch 5th generation 32GB/64GB: Ver.7.1.1

iPod touch 4th generation 8GB/32GB/64GB: Ver.6.1.3

iPod touch 3rd generation 32GB/64GB: Ver.5.1.1

iPod touch 2nd generation 8GB/16GB/32GB: Ver.4.2.1

iPod touch 1st generation 8GB/16GB/32GB: Ver.3.1.3

iPod nano 7th generation 16GB: Ver.1.0.2

iPod nano 6th generation 8GB/16GB: Ver.1.2

iPod nano 5th generation (video camera) 8GB/16GB: Ver.1.0.2

iPod nano 4th generation (video) 8GB/16GB: Ver.1.0.4

iPod nano 3rd generation (video) 4GB/8GB: Ver.1.1.3

iPod classic (Late2009) 160GB: Ver.2.0.4

iPod classic 120GB: Ver.2.0.1

iPod classic 80GB/160GB: Ver.1.1.2

• The following devices have been tested and shown to work with

this unit. Correct function of earlier versions cannot be

guaranteed.

iPhone 5S 16GB/32GB/64GB: Ver.7.1.1

iPhone 5C 16GB/32GB/64GB: Ver.7.1.1

iPhone 5 16GB/32GB/64GB: Ver.7.1.1

iPhone 4S 16GB/32GB/64GB: Ver.7.1.1

iPhone 4 16GB/32GB: Ver.7.1.1

iPhone 3GS 8GB/16GB/32GB: Ver.6.1.3

iPhone 3G 8GB/16GB: Ver.4.2.1

iPhone 4GB/8GB/16GB: Ver.3.1.3

• For clarity in identifying your model of iPod, please see Apple’s

own document “Identifying iPod models” at

http://support.apple.com/kb/HT1353.

iPod/iPhone main screen example

Audio mode

Function mode

Video mode

Artwork display

• You can change the artwork position. For details, see “Switching

the Artwork Position” (page 40).

: During audio-only playback of a video file in a Playlist,

the Video icon is displayed.

Current song no./Total song no.

iPod/iPhone

(Optional)

WARNING

It is dangerous for the driver to watch video while driving

the vehicle. The driver may be distracted from looking

ahead and an accident could occur.

Install the unit correctly so that the driver cannot watch a

video unless the car is stopped and the parking brake is

applied.

If the unit is not installed correctly, the driver will be able

to watch a video while driving and may be distracted

from looking ahead and cause an accident. The driver or

other people could be severely injured.

58-EN

Artist title/Release Date*

Song title/Episode title*

Album title/Podcast title*

Total time for playing

Elapsed time

Quick Search button

Touch or swipe to the right when using Quick Search mode.

: During audio-only playback of a music file in a video

Playlist, the Music icon is displayed.

Info mode switching button (Video mode only)

Info mode display

*Podcast mode.

Quick Search mode screen example

Swipe vertically in the list to change pages.

Full Search button

Swipe to the right when using Full Search mode.

The iPod/iPhone operation screen display during video file

playback

Touch the screen while the iPod/iPhone playback screen is

displayed.

The iPod/iPhone operation screen is displayed.

• The operation screen changes to the visual screen in the iPod mode for 5

seconds after an operation has been performed.

Playback

1Press the (AUDIO) button to select iPod mode.

The display shows the iPod mode screen.

• You can select and change the source in the Menu screen (page 21)

or Favorite screen (page 24).

2Touch [ ] or [ ] or to select the desired track (file).

Returning to the beginning of the current (or previous) track (file):

Touch [ ].

Fast reverse the current track :

Touch and hold [ ].

Advancing to the beginning of the next track (file) :

Touch [ ].

Fast forward the current track :

Touch and hold [ ].

• The , buttons provide the same functions above.

3To pause playback, touch [/].

• If a song is playing on the iPod/iPhone before it is connected to the unit,

it will continue playing when it is connected.

• An episode may have several chapters. The chapter can be changed by

touching [ ] or [ ].

• If the artist, album or song name, created in iTunes, has too many

characters, songs may not be played back when connected to the unit.

Therefore, a maximum of 64 characters is recommended. The

maximum number of characters for the unit is 64.

• Some characters may not be correctly displayed.

Searching for a Music File

An iPod/iPhone can contain thousands of songs. For this reason, this

unit can make various searches using the search function as shown

below.

Using the Playlist/Artist/Album/Podcast/Audiobook/Genre/Composer/

Song search mode’s individual hierarchy, you can narrow down your

search as shown in the table below.

In Quick Search mode, the list from the previous search mode is

displayed. For example, if the last time you searched for songs was is in

Albums, the Album list is displayed. If you have not used the search

mode, the list is not displayed in the Quick Search mode. In this case, go

to the Full Search mode.

In Quick Search mode, touch the desired list (for example,

Album list).

The selected Album is played.

• To switch into Quick Search mode, see in “iPod/iPhone main screen

example” (page 57).

• To search within an Album, go to the Full Search mode.

Hierarchy 1 Hierarchy 2 Hierarchy 3 Hierarchy 4

Playlists Songs — —

Artists Albums Songs —

Albums Songs — —

Songs — — —

Podcasts Episodes — —

Genres Artists Albums Songs

Composers Albums Songs —

Audiobooks — — —

Quick Search Mode

59-EN

For example: Searching by Artist name

The following example explains how an Artists search is performed.

Another search mode can be used for the same operation, although the

hierarchy differs.

1Touch [Artists] in the Full Search mode screen.

The Artists search screen is displayed.

• To switch into Full Search mode, see in “Quick Search mode

screen example” (page 58).

2Select the desired artist.

To play back the Artist directly

1 Touch [ ] of the artist’s name.

All songs of the selected artist are played back.

To search for the Album of the Artist

1 Touch the selected artist name.

The Albums search screen of the selected artist is displayed.

2 Touch [ ] of the desired album’s name.

All songs of the selected album are played back.

To search for a Song in the Album of the Artist

1 Touch the desired artist’s name.

All albums of the selected artist are displayed.

3Touch the desired album’s name.

All songs of the selected album are displayed.

4Touch the desired song’s name.

The selected song is played back.

• Touching [ ] of “All” will play back all songs in the list.

• Touching “All” will display the search list in the next hierarchy.

• An alphabet skip function is available. See “Alphabet Search Function”

(page 59).

• To switch the displayed list or return to the previous page in the Full

Search mode, see “About Basic Operation for List Screen” (page 18).

Searching for a Desired Video File

You can select a movie, music video, etc., from the list screen.

• Video search mode depends on the iPod/iPhone. If the specification of

the iPod/iPhone is changed, the search mode on this unit will also be

changed.

Examples for the video search mode

• Video Playlists

• Movies

• Music Videos, etc.

For example: Searching by Movie

The following example explains how a Movie search is performed. Another

search mode can be used for the same operation, although the hierarchy

differs.

1Touch the [Video] icon in the Full Search mode screen.

The Video search screen is displayed.

• To switch into Full Search mode, see in “Quick Search mode

screen example” (page 58).

• If the Video icon is not displayed, touch [More] to change the

Search mode.

2Touch [Movies].

The Movies search screen is displayed.

3Touch the desired movie.

The selected movie is played back.

Alphabet Search Function

The unit is provided with an alphabet search function for effective

searching. When you use this function in the search mode, you can

quickly search an artist or a song, etc.

This is an example of how to search Artist Name for names beginning

with “R”.

1Touch “O-U” of the alphabet group.

“O P Q R S T U” of the alphabet group “O - U” is displayed.

2Touch “R” you want to search.

Artist names beginning with “R” are displayed.

3Touch your desired artist name.

• If there are no names in the list beginning with that letter, the next letter

of the alphabet is searched.

For example: If there are no names beginning with “R,” the search list

begins with “S.”.

Full Search Mode

ALPS ALPINE 9ZUA145 Car Navigation Unit User Manual 68 29530Z12 A c3 comm FCC

Alpine Electronics Inc Car Navigation Unit 68 29530Z12 A c3 comm FCC

Contents

(Short-Term Confidential) User Manual_2

Navigation menu

Namespaces

Views

Navigation