ALPS ALPINE UGPZ4 Modular Bluetooth Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	544686
Application ID	Le3wj82i+MJI53KbGhIs2g==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.93kB (49127 bits)
Date Submitted	2005-05-22 00:00:00
Date Available	2005-05-22 00:00:00
Creation Date	2005-05-14 12:18:40
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2005-05-14 12:18:40
Document Title	untitled

ALPS BluetoothTM Transceiver Module UGPZ4 Ver. 1.0
May 9, 2005
User Guide Information to 2.4GHz ALPS BluetoothTM Transceiver Module
Model UGPZ4
Caution: This user guide information is only provided to OEM or module installer.
Do not supply to the end user.
1. Introduction:
The ALPS, UGPZ4 with BluetoothTM wireless technology is a radio device that transmits and receives
radio signals in accordance with the spectrum regulations for the 2.4 GHz unlicensed frequency range.
The following table shows a major function.
Model
No.
UGPZ4
Major Function
Remarks
1. Output Power; Bluetooth™ class 2. 2.5mW (+4dBm) Max.
2. On-board antenna provided.
3. Voltage regulator built in. Rating of Input voltage: +3.3Vdc, +/-0.2V
4. Programmed 4Mbit built in
5. Reference oscillator built in
6.Operating temperature: Nominal; +15 °C to +35°C
7. Regulatory frequency range
USA, Canada, Europe, Taiwan, Korea, China and Japan: 2400 – 2483.5MHz
Integrated
antenna
provided
Electrical features
Program memory
RAM
Reference oscillator
Sub clock oscillator
Serial data interface
Contents
4M bit ROM
32k bytes
Built in
Built in
UART(BCSP or H4)
2. Radio part
Bluetooth™ Transceiver Module, model UGPZ4 has fully integrated 2.4GHz radio transceiver with Class2 power,
receiver and frequency-hopping synthesizer.
Then, UGPZ4 has also provision of Adaptive Frequency Hopping (AFH) that is used to improve the performance
of physical links in the presence of interference as well as reducing the interference caused by physical links on
other devices in the ISM band. AFH shall only be used during the connection state.
In order to facilitate power management, each section of the radio may be powered up and down separately.
Various software controllable switches have been implemented to control power to the transmitter, the frequency
synthesizer/VCO, the receiver and the LNA, if provided.
3. Base band part
Bluetooth™ Transceiver Module contains link controller, which performs all the real-time functions of the
Bluetooth™ baseband protocol layer, including data transfer and connection management. The device also
controls states of operation enables sniff, park and hold modes of operation. Real-time functions such as
frequency-hopping burst timing and clock synchronization are also implemented in this hardware. Further
processing is required to format the data into the Bluetooth™ packet format before it may be applied to the GFSK
modulator. On the receive side the controller performs error correction and de-scrambling before de-packetizing
the incoming payload and storing it in RX buffers.
The link controller hardware also implements the basic, repetitive actions of paging, inquiry, page or inquiry scans
and the general Bluetooth™ modes of park and sniff. This ensures that the processor used to implement the Link
Manager and other lower layer protocol can be kept inactive.
Copyright © 2005 ALPS ELECTRIC CO., LTD.
page1
ALPS BluetoothTM Transceiver Module UGPZ4 Ver. 1.0
May 9, 2005
4. Eligibility requirements for regulatory approval:
As a part of regulatory certification, ALPS will provide an approval for certain countries in the form of modular
approval (MA) .
The regulatory approval is required for each country throughout world where the end-user wishes to use ALPS
UGPZ4 into entire end product, if no certification program for the modular approval exists in the country.
The countries that can accept MA include the USA, Canada, Taiwan, Korea, China, Japan and certain European
countries.
The conditions for approval of ALPS UGPZ4 and related information for each country are described below.
ALPS wishes that our customer for end product would contact with us about what module of UGPZ4 has been
certified for each country.
4.1 USA
4.1.1 Compliance statement to FCC
This module complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
4.1.2 RF exposure compliance
This module may be installed into any end product in mobile device applications.
Because the module only radiates very low power levels, it complies with RF exposure requirements.
4.1.3 Requirements to end product
The following provisions for end product will be required on the FCC regulation, part 15.
(1) Antenna
ALPS wishes that our customer shall use the UGPZ4 module without any modifications including
antenna. If customer use a unique antenna, the FCC certification is required for the end product.
(2) Markings
To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the
end product.
Contains Transmitter Module FCC ID: CWTUGPZ4
Any similar wording that expresses the same meaning may be used.
(3) Caution to user for modification
The following caution is expressed on the user’s instruction manual.
The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the device.
(4) Compliance statement to FCC
The following statement is expressed on the user’s instruction manual.
This module complies with part 15 of the FCC rules. Operation is subject to the
following conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Copyright © 2005 ALPS ELECTRIC CO., LTD.
page2
ALPS BluetoothTM Transceiver Module UGPZ4 Ver. 1.0
May 9, 2005
4.2 Canada
In general, I.C (Industry Canada) follows the FCC in terms of emission levels and other regulatory
requirements.
4.2.1 Compliance statement for IC
This device complies with Industry Canada RSS-210. Operation is subject to the following conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
4.2.2 RF exposure compliance
(1) This module may be installed into any end product in mobile device applications.
Because the module only radiates very low power level, it complies with RF exposure requirements.
(2) The installer of this device must ensure that the antenna is located or pointed such that it does not
emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6,
obtainable from Health Canada’s website www.hc-sc.gc.ca/rpb.
4.2.3 Meaning of certification number
The meaning of the marking of “IC:1788F-UGPZ4” on the UGPZ module means: “1788F-UGPZ4” is the
certification number, and the term “IC’ before the equipment certification number only signifies that Industry
Canada technical specifications were met.
4.2.4 Requirements to end product
The following provisions for end product will be required on the Canada regulation.
(1) Antenna
ALPS wishes that our customer use the UGPZ4 module without any modifications including antenna.
If customer use a unique antenna, the I.C certification is required for the end product.
(2) Markings
To satisfy Industry Canada exterior labeling requirements, the following text must be placed on the
exterior of the end product.
Contains Transmitter Module IC: 1788F-UGPZ4
Any similar wording that expresses the same meaning may be used.
4.3 Europe
The UGPZ4 module with CE marking will assist our customer into advance.
The end product containing UGPZ4 module with CE marking will be required further involvement of R&TTE
directive Notified Body, where the end product installs UGPZ4 module with no modification of the antenna in
conformance with ALPS’s installation instructions.
The our customer of the end product is in doubt then the end product integrating the UGPZ4 module must be
assessed against Article 3.2 of the R&TTE Directive.
Note: The our customer for the end product containing UGPZ4 module without CE marking shall be required
further application to R&TTE directive.
Copyright © 2005 ALPS ELECTRIC CO., LTD.
page3
ALPS BluetoothTM Transceiver Module UGPZ4 Ver. 1.0
May 9, 2005
4.4 Japan
4.4.1 Radio law (TELEC or other registered testing house)
The our customer for the end product will not require the certification of TELEC or other registered testing house
for the end product, where UGPZ4 module with TELEC or other registered testing house certification shall be
incorporated in the following applications.
(1) Antenna
ALPS wishes that our customer shall use the UGPZ4 module without any modifications including antenna.
If customer use a unique antenna, the re-certification to TELEC or other registered testing house will be
required for the UGPZ4 module.
Thus, our customer would be required to contact with ALPS before the modification of the antenna.
(2) The outer cabinet of the end product shall be fixed by easily access method, such fixing with plus /
minus screws to open the outer cabinet by general public.
The permanently fixing method, such using security screws are not allowed for mounting method.
The labeling to exterior of the end product has a meaning of “Contains transmitter device certified
under Japanese radio law ”, or similar wording. (see below)
「電波法適合無線設備を内蔵」
（“Contains transmitter device certified under Japanese radio law ” ）
(3) Where outer cabinet of the end product containing UGPZ4 module is secured by the permanently
securing method, such using security screws, the our customer for the end product shall obtain TELEC
or other registered testing house certification by themselves for the end product, even if UGPZ4 module
has been certified by TELEC or other registered testing house.
4.4.2 Telecommunications law (JATE or other registered testing house)
(1) The end product containing UGPZ4 module shall be certified by JATE, where the end product is
directly or indirectly connected to telecommunication line, such public telephone, even if UGPZ4
module has been certified by JATE or other registered testing house, or not.
(2) Since the UGPZ4 module is not certified by JATE or other registered testing house, our customer
for the end product containing UGPZ4 module would be required as that;
a) In case of that outer cabinet is fixed by easily access method, such fixing with plus / minus
screws to open the outer cabinet by general public, the user manual for the end product has a
caution to the end user about the meaning of “Easily removable wireless transmitter is
integrated”, or similar wording. (see below)
「容易に取り外せる無線設備が内蔵されています。」
（“Easily removable wireless transmitter is integrated”）
Any similar wording that expresses the same meaning may be used.
b) Where outer cabinet is secured by the permanently securing method, such using security screws,
the our customer for the end product shall obtain JATE or other registered testing house certification by
themselves for the end product, even if UGPZ4 module has been certified by JATE or other registered
testing house, or not.
Copyright © 2005 ALPS ELECTRIC CO., LTD.
page4
ALPS BluetoothTM Transceiver Module UGPZ4 Ver. 1.0
May 9, 2005
4.4.3 Wireless LAN voluntary standard (ARIB)
ARIB STD-T66 is a voluntary standard in Japan.
However, ALPS strongly recommend providing the following application for the end product.
(1) User manual.
The user manual specifies the following cautions or similar meanings and explanation of markings
indicated on the end product.

この機器の使用周波数帯では、電子レンジ等の産業・科学・医療用機器のほか、工場の製造ライン
等で使用されている移動体識別用の構内無線局(免許を要する無線局)及び特定小電力無線局(免許
を要しない無線局)並びにアマチュア無線局（免許を要する無線局)が運用されています。
１．この機器を使用する前に、近くで移動体識別用の構内無線局及び特定小電力無線局並びにアマ
チュア無線局が運用されていないことを確認して下さい。
２．万一、この機器から移動体識別用の構内無線局に対して有害な電波干渉の事例が発生した場合
には、速やかに使用周波数を変更するか又は電波の発射を停止した上、下記連絡先にご連絡頂
き、混信回避のための処置等（例えば、パーティションの設置など）についてご相談して下さ
い。
３．その他、この機器から移動体識別用の特定小電力無線局あるいはアマチュア無線局に対して、
有害な電波干渉の事例が発生した場合などの何かお困りのことが起きたときは、次の連絡先へ
お問い合わせください。
連絡先：
(2) Sticker
The end product provides a sticker describing the same cautions of user manual.
There are no specifications for material, size and shape.
(3) Catalogue, pamphlet and web site
The catalogue, pamphlet and web site for the end product specify the meaning of same cautions of
user manual and meaning of markings shown In the end product.
(4) Markings on end product
The following markings are marked on the end product and its package.
The user manual describes the meaning of the markings.
If there is no spacing on the end product, the sticker is used as an alternate.

2.4 FH x
1) “ 2.4 “ means radio operated in 2.4 GHz bands.
2) “ FH “ means modulating type, FH-SS.
3) “ x “ means that distance for interference is less than “y” m on the assumption.
Product No.
UGPZ4
Output power
+3.0dBm / 0.002W max.
“x”
“y”
10m
4) “
“ means the product is used in all frequency band from 2400MHz to
2483.5MHz and there are no possibilities of an avoidance to the other bands.
Copyright © 2005 ALPS ELECTRIC CO., LTD.
page5
ALPS BluetoothTM Transceiver Module UGPZ4 Ver. 1.0
May 9, 2005
4.5 People’s Republic of China
The UGPZ4 module has the following information on China certification.
1) Manufacturer
ALPS ELECTRIC CO., LTD
2) Model number
UGPZ4
3) CMII ID:xxxxZZZZZZ
4.6 Korea
The UGPZ4 module has the following information on Korea certification.
1) Manufacturer
ALPS ELECTRIC CO., LTD
2) Model number
UGPZ4
3) Marking
MIC marking and certification number
Note:
1. The BLUETOOTH TM are owned by Bluetooth SIG, Inc., U.S.A.
Copyright © 2005 ALPS ELECTRIC CO., LTD.
page6

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 6
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:d0321cc4-0cc5-4505-86c2-abe330ed70cb
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Modify Date                     : 2005:05:14 12:18:40+09:00
Create Date                     : 2005:05:14 12:18:40+09:00
Document ID                     : uuid:d076c9cc-236f-4563-9d05-5f3540acfe3f
Format                          : application/pdf
Title                           : untitled

EXIF Metadata provided by EXIF.tools