AMPAK Technology AP6234A Wifi Dual Band + BT combo module User Manual
AMPAK Technology Inc. Wifi Dual Band + BT combo module Users Manual
Contents
- 1. User manual
- 2. User Manual.pdf
- 3. User Manual
- 4. Users Manual
Users Manual
Ampak AP6234AL Evaluation Kits User manual Version 1.2 Revision History Date 2012/12/26 2013/03/07 2013/06/06 AMPAK Technology Inc. Doc. NO: Revision Content Initial released Modify figure1 Modify figure1 www.ampak.com.tw Revised By Version Dora 1.0 Dora 1.1 Dora 1.2 Proprietary & Confidential Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This EUT is compliance with SAR for general population/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. 2006/8/16 v1.0 This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna, 2) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains FCC ID: ZQ6-AP6234A”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 2006/8/16 v1.0 Industry Canada statement: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and (iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. (iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement: (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.; (iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas. (iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. 2006/8/16 v1.0 Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible. This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: 1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 1 condition ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains IC:11956AAP6234A”. 2006/8/16 v1.0 Plaque signalétique du produit final Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 11956A-AP6234A". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel. This radio transmitter (IC: 11956A-AP6234A) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (IC: 11956A-AP6234A) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Operating Frequency (MHz) / Gain (dBi) Connector Ant. No. Type Dipole(Original) UFL PIFA(New) 3.53 5.30 4.93 5.31 5.55 UFL 2006/8/16 2400~2483.5 5150~5250 5250~5350 5470~5725 5725~5850 v1.0 KCC 해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없음 해당 무선 설비는 5150-5250MHz 대역에서 실내 에서안 사용만 수 있웅. (Translation: the service related to human safety is not allowed because this device may have the possibility of the radio interference.) For RF device using 5150-5250MHz, this device shall be used for indoor only. 2006/8/16 v1.0 802.11b/802.11g/BT 警語 第十二條→經型式認證合格之低 原設計之特性及 能 率射頻電機,非經許 第十四條→低 立即停用,並改善 至無 或使用者均不得擅自變更頻率 率射頻電機之使用不得影響飛航安 及 擾合法通信 大 經發現有 率或 變更 擾現象時,應 擾時方得繼續使用 前項合法通信,指依電信法規定作業之無線電通信 射性電機設備之 ,公司,商 低 率射頻電機須忍 合法通信或工業 科學及醫療用電波輻 擾 802.11a 警語 無線傳輸設備 (UNII) 在 5.25-5.35 秭赫頻帶 不得 擾合法通信 操作之無線資訊傳輸設備,限於室 如造成 擾,應立即停用,俟無 擾之 使用 ,始得繼續 使用 保頻率穩定性,如依製造廠商使用手冊上所述正常操作,發射的信 模組請 1. 2. (4.7.5) 無線資訊傳輸設備忍 (4.7.7) 得認證後將依規定於模組本體標示審驗合格標籤 系統廠商應於 上標示 本產品 含射頻模組: 擾且 (4.7.6) 無線資訊傳設備的製造廠商應確 應維持於操作 頻帶中 註 本模組於 合法通信之 CCAFXXLPXXXXTX) 字樣 1. AP6XXX Evaluation Board Introduction AP6XXX Evaluation board (EVB) likes as figure1. That is designed for IEEE802.11 a/b/g/n/ac WLAN with integrated Bluetooth, FM, NFC and GPS application. It is subject to provide a convenient environment for customer’s verification on WiFi or Bluetooth function. There are many controller pins and reserved GPIO on Evaluation board which describes as below. Figure1. Top view of AP6XXX EVB Interface highlights: 1. U1: AP6XXX SIP module. 2. J1: UART interface connects with UART transport board for BT and GPS measuring, it also provides I2C (SDA/SCL) for NFC measuring. 3. J2: Enable(H) or disable(L) Bluetooth, WiFi, NFC function and AP6335_SDIO I/O voltage selection.(H for SDIO 3.3V, L for SDIO 1.8V) 4. J3: FM audio out interface. 5. 6. 7. 8. J5: 5V DC adaptor input connector. J6: VBAT / WL_VIO / BT_VIO for main system I/O power path. J7: 5V DC mini USB input connector. J8: Standard SDIO interfaces for Wi-Fi performance measured. AMPAK Technology Inc. Doc. NO: www.ampak.com.tw Proprietary & Confidential Information 9. J11: WL_VIO power path for 1V8 or 3V3 selection. 10. SW1: Power on/off switch. 11. CN1: NFC interface connects with NFC antenna. 12. S1: SMA connector let RF signal in/out path, you could connect with RF cable or Dipole antenna. 13. S2: SMA connector let GPS RF signal input, you could connect with GPS antenna. 14. Ct1: WLAN and BT control pins, strongly recommended WL_HWAKE(IRQ) connected to MCU. 15. Ct2: NFC control pins, strongly recommended N_WAKE and N_H_WAKE connected to MCU. 2. WiFi function verification step WIFI SDIO: Using external pull up resistors depends on the SDIO supply voltage. For 1.8V, the resistance range is 30KΩ~82KΩ. For 3.3V, its range from 21 KΩ~41 KΩ on the four data lines and the CMD line as the following circuitry. VIO_3V3 R7 R6 J8 SD2 SD3 SDCMD GND 3.3V SDCLK GND SD0 SD1 SDIO_D2 SDIO_D3 SDIO_CMD SDIO_CLK SDIO_D0 SDIO_D1 R10 R28 R29 C10 10uF SDIO_3V3 Golden Finger_9 Figure2. WiFi verification connection interface to Host SDIO Hardware Setup: Refer to Figure2 SDIO pin definition connects the J8 interface of AP6XXX evaluation board to Host SDIO control interface. Using pull high resistors (R6, R7, R10, R28, R29) that resistance is 30Kohm for 1.8V or 3.3V VDDIO pull up voltage. (Pull high resistors are un-necessary if at verification phase.) Connects an external antenna at SMA connector on the evaluation board. Note to the VDDIO voltage level should be the same with GPIO voltage level of Host CPU. (VDDIO 3.3V or 1.8V selection by jump J11) WiFi software setup: Please follow up software guideline of Ampak official released. AMPAK Technology Inc. Doc. NO: www.ampak.com.tw Proprietary & Confidential Information 3. Bluetooth function verification step Figure3. Bluetooth verification connection interface to Host UART Hardware Setup: Refer to Figure3 UART pin definition connects the J1 interface of AP6XXX evaluation board to Host UART control interface. Connects an external antenna at SMA connector on the evaluation board. Note to the VDDIO voltage level should be the same as GPIO voltage level of Host CPU. WiFi and Bluetooth software setup: Please follow up software guideline of Ampak official released. AMPAK Technology Inc. Doc. NO: www.ampak.com.tw Proprietary & Confidential Information AP6234ALNS(HF) Datasheet 2. Features IEEE 802.11x Key Features • Dual-band 2.4GHz/5GHz 802.11a/b/g/n. • • • Single-stream IEEE 802.11n support for 20MHz and 40MHz channels provides PHY layer rates up to 150Mbps. WLAN host interface options: SDIO v2.0 — up to 50 MHz clock rate Support a single antenna shared between WLAN and Bluetooth. • Security: WEP, WPS, WPA, WPA2, WMM, WAPI, AES,… Bluetooth Features • • Bluetooth V4.0(BLE) Low Energy with provisions for supporting future specifications. Bluetooth Class1 or Class2 transmitter operation. • BT host digital interface UART(up to 4 Mbps) with support all Bluetooth4.0 package types • Multipoint operation with up to seven active ACL links, three active SCO and eSCO connections. Full support for power savings modes (standard sniff, deep sleep modes) • • ECI - enhanced coexistence support, ability to coordinate BT SCO transmissions around WLAN receives A simplified block diagram of the module is depicted in the figure below. AMPAK Technology Inc. Doc. NO: www.ampak.com.tw Proprietary & Confidential Information AP6234ALNS(HF) Datasheet 3. Deliverables 3.1 Deliverables The following products and software will be part of the product. Module with packaging Evaluation Kits Software utility for integration, performance test. Product Datasheet. Agency certified pre-tested report with the adapter board. 3.2 Regulatory certifications The product delivery is a pre-tested module, without the module level certification. For module approval, the platform’s antennas are required for the certification. AMPAK Technology Inc. Doc. NO: www.ampak.com.tw Proprietary & Confidential Information AP6234ALNS(HF) Datasheet 4. General Specification 4.1 General Specification Model Name AP6234 Product Description Supports Wi-Fi dual mode /Bluetooth functionalities Dimension L x W x H: 13.0 x15.0 x 1.3 (typical) mm WiFi Interface SDIOV2.0 BT Interface UART/ PCM Operating temperature -30°C to 85°C Storage temperature -40°C to 85°C Humidity Operating Humidity 10% to 95% Non-Condensing 4.2 Voltages 4.2.1 Absolute Maximum Ratings Symbol VBAT VDDIO Description Min. Max. Unit Input supply Voltage Digital/Bluetooth/SDIO/ I/O Voltage -0.5 -0.5 3.6 4.2.2 Recommended Operating Rating The module requires two power supplies: VBAT and VDDIO. Min. Typ. Max. Unit -30 25 85 VBAT 3.0 3.6 4.8 deg.C VDDIO 1.6 3.3 3.4 Operating Temperature AMPAK Technology Inc. Doc. NO: www.ampak.com.tw Proprietary & Confidential Information AP6234ALNS(HF) Datasheet 5. WiFi RF Specification 5.1 2.4GHz & 5GHz RF Specification Conditions : VBAT=3.6V ; VDDIO=3.3V ; Temp:25°C Feature Description WLAN Standard IEEE 802.11a/b/g/n, WiFi compliant Frequency Range 2.400 GHz ~ 2.497 GHz (2.4 GHz ISM Band) 4.900 GHz ~ 5.845 GHz (5.0 GHz ISM Band) Number of Channels 2.4GHz:Ch1 ~ Ch14 5.0GHz:Please see the table1 Modulation 802.11a : OFDM /64-QAM,16-QAM, QPSK, BPSK 802.11b : DQPSK, DBPSK, CCK 802.11 g/n : OFDM /64-QAM,16-QAM, QPSK, BPSK 802.11a /54Mbps : 13 dBm ± 1.5 dB @ EVM -25dB Output Power 802.11b /11Mbps : 16 dBm ± 1.5 dB @ EVM -9dB 802.11g /54Mbps : 15 dBm ± 1.5 dB @ EVM -25dB 802.11n /MCS7 : 14 dBm ± 1.5 dB @ EVM -28dB Receive Sensitivity (11n,20MHz) @10% PER Receive Sensitivity (11n,40MHz) @10% PER - MCS=0 PER @ -88 dBm, typical - MCS=1 PER @ -84 dBm, typical - MCS=2 PER @ -82 dBm, typical - MCS=3 PER @ -80 dBm, typical - MCS=4 PER @ -77 dBm, typical - MCS=5 PER @ -74dBm, typical - MCS=6 PER @ -72 dBm, typical - MCS=7 PER @ -70 dBm, typical - MCS=0 PER @ -87 dBm, typical - MCS=1 PER @ -83 dBm, typical - MCS=2 PER @ -81 dBm, typical - MCS=3 PER @ -79 dBm, typical - MCS=4 PER @ -77 dBm, typical - MCS=5 PER @ -76 dBm, typical - MCS=6 PER @ -71 dBm, typical - MCS=7 PER @ -70 dBm, typical Receive Sensitivity (11g) @10% PER AMPAK Technology Inc. Doc. NO: 6Mbps PER @ -89 dBm, typical 9Mbps PER @ -88 dBm, typical - 12Mbps PER @ -86 dBm, typical www.ampak.com.tw Proprietary & Confidential Information AP6234ALNS(HF) Datasheet - 18Mbps PER @ -84 dBm, typical - 24Mbps PER @ -82 dBm, typical - 36Mbps PER @ -78 dBm, typical - 48Mbps PER @ -75 dBm, typical - 54Mbps PER @ -73 dBm, typical - 1Mbps PER @ -95 dBm, typical Receive Sensitivity (11b) - 2Mbps @8% PER - 5.5Mbps PER @ -94 dBm, typical PER @ -90 dBm, typical - 11Mbps PER @ -87 dBm, typical 6Mbps PER @ -88 dBm, typical 9Mbps PER @ -86 dBm, typical - 12Mbps PER @ -84 dBm, typical Receive Sensitivity (11a) - 18Mbps @10% PER - 24Mbps PER @ -82 dBm, typical - 36Mbps PER @ -78 dBm, typical - 48Mbps PER @ -75 dBm, typical - 54Mbps PER @ -73 dBm, typical Maximum Input Level PER @ -80 dBm, typical 802.11b : -10 dBm 802.11a/g/n : -20 dBm 802.11a : 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b : 1, 2, 5.5, 11Mbps Data Rate 802.11g : 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11n: MCS0, MCS1, MCS2, MCS3, MCS6, MCS7 Antenna Reference MCS4, MCS5, Small antennas with 0~2 dBi peak gain 5GHz Channel table Band (GHz) 5.15GHz~5.25GHz 5.25GHz~5.35GHz 5.5GHz~5.7GHz AMPAK Technology Inc. Doc. NO: Operating Channel Numbers Channel center frequencies(MHz) 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 www.ampak.com.tw Proprietary & Confidential Information AP6234ALNS(HF) Datasheet 128 132 136 140 149 153 157 161 5.725GHz~5.825GHz 5640 5660 5680 5700 5745 5765 5785 5805 6. Bluetooth Specification 6.1 Bluetooth Specification Conditions : VBAT=3.6V ; VDDIO=3.3V ; Temp:25°C Feature Description General Specification Bluetooth Standard Bluetooth V4.0 of 1, 2 and 3 Mbps. Host Interface UART Antenna Reference Small antennas with 0~2 dBi peak gain Frequency Band 2.400 GHz ~ 2483.5 GHz Number of Channels 79 channels Modulation FHSS, GFSK, DPSK, DQPSK RF Specification Min. Typical. Output Power (Class 1.5) 10 dBm Output Power (Class 2) 2 dBm Sensitivity @ BER=0.1% for GFSK (1Mbps) -86 dBm Sensitivity @ BER=0.01% for π/4-DQPSK (2Mbps) -86 dBm Sensitivity @ BER=0.01% for 8DPSK (3Mbps) -80 dBm Max. GFSK (1Mbps):-20dBm Maximum Input Level π/4-DQPSK (2Mbps) :-20dBm 8DPSK (3Mbps) :-20dBm AMPAK Technology Inc. Doc. NO: www.ampak.com.tw Proprietary & Confidential Information AP6234ALNS(HF) Datasheet 7. Pin Assignments 7.1 Pin Outline < TOP VIEW > 7.2 Pin Definition NO Name GND WL_BT_ANT Type - Description Ground connections GND I/O - Ground connections NC - Floating (Don’t connected to ground) NC - Floating (Don’t connected to ground) BT_WAKE HOST wake-up Bluetooth device BT_HOST_WAKE Bluetooth device to wake-up HOST NC - Floating (Don’t connected to ground) VBAT Main power voltage source input 10 XTAL_IN Floating (Don’t connected to ground) 11 XTAL_OUT Floating (Don’t connected to ground) 12 WL_REG_ON Internal regulators power enable/disable 13 WL_HOST_WAKE WLAN to wake-up HOST AMPAK Technology Inc. Doc. NO: www.ampak.com.tw RF I/O port Proprietary & Confidential Information 10 AP6234ALNS(HF) Datasheet 14 SDIO_DATA_2 I/O SDIO data line 2 15 SDIO_DATA_3 I/O SDIO data line 3 16 SDIO_DATA_CMD I/O SDIO command line 17 SDIO_DATA_CLK I/O SDIO clock line 18 SDIO_DATA_0 I/O SDIO data line 0 19 SDIO_DATA_1 SDIO data line 1 20 GND I/O - Ground connections 21 VIN_LDO_OUT Internal Buck voltage generation pin 22 VDDIO I/O Voltage supply input 23 VIN_LDO Internal Buck voltage generation pin 24 LPO Low power oscillator clock input (32.768KHz) 25 PCM_OUT PCM Data output 26 PCM_CLK I/O PCM clock 27 PCM_IN PCM data input 28 PCM_SYNC PCM sync signal 29 NC I/O - Floating (Don’t connected to ground) 30 NC - Floating (Don’t connected to ground) 31 GND - Ground connections 32 NC - Floating (Don’t connected to ground) 33 GND - Ground connections 34 BT_RST_N Low asserting reset for Bluetooth core 35 NC - 36 GND - Ground connections 37 NC - Floating (Don’t connected to ground) 38 NC - Floating (Don’t connected to ground) 39 NC - Floating (Don’t connected to ground) 40 NC - Floating (Don’t connected to ground) 41 UART_RTS_N Bluetooth UART interface 42 UART_TXD Bluetooth UART interface 43 UART_RXD Bluetooth UART interface 44 UART_CTS_N Bluetooth UART interface 45 TP1 - Floating (Don’t connected to ground) 46 TP2 - Floating (Don’t connected to ground) 47 TP3 - Floating (Don’t connected to ground) AMPAK Technology Inc. Doc. NO: www.ampak.com.tw Floating (Don’t connected to ground) Proprietary & Confidential Information 11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract Author : bart.lin Create Date : 2014:09:25 14:41:30+08:00 Modify Date : 2014:09:25 16:12:35+08:00 Language : zh-TW Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : bart.lin Creator Tool : Microsoft® Word 2010 Metadata Date : 2014:09:25 16:12:35+08:00 Producer : Microsoft® Word 2010 Document ID : uuid:19dca392-af7e-435c-8efc-d22dbd65f857 Instance ID : uuid:00d921ad-5d19-4cf2-b219-11b665f195cb Page Count : 19EXIF Metadata provided by EXIF.tools