AMPAK Technology GT966X bluetooth module User Manual GT966X EVKits V2 0 20110919

AMPAK Technology Inc. bluetooth module GT966X EVKits V2 0 20110919

User Manual

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information i Doc. NO: AMPAK GT966X Evaluation Kits User manual Version 2.0 Revision History Date Revision Content Revised By Version 2011/09/24 Initial released Andy 2.0
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information i Doc. NO: Contents 1. GT966X evaluation board introduction..................................................................... 1 2. PIN Description........................................................................................................... 3 3333. Federal Communication Commission Interference Statement.............................. 4
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 1 1. GT966X evaluation board introduction GT966X evaluation board (EVB) likes as figure1. That is designed for Bluetooth 2.1+EDR application. The bottom views like as figure2. It is also designed for TI’s MSP430 and TMX320C5X experimenter board. It is subject to provide a convenient environment for customer’s verification on Bluetooth function. There are controller pins on evaluation board which describes as below. Figure1. Top view of GT966X EVB
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 2 Figure2. Bottom view of GT966X EVB Interface highlights: 1. U4: GT966X SIP module. 2. S1: U.FL connector let RF signal in/out path, which R55 need tie on 0ohm. 3. J10: VBAT：：：： 3V3 for main system power path. IO ：：：：1V8 for system IO level path. S/M：：：：PCM mode (Jump onPCM slave mode. Jump offPCM master mode) 4. J1&J2: For TI’s experimenter board IO used.
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 3 2. PIN Description Connector No. Pin Name Def. Dir. Description of Options (Common) J1 1,19 GND Connect to ground 3 HCI_CTS_3V3 I HCI UART clear-to-send 5 SLOW_CLK_3V3 I 32.768-KHz clock in 7 HCI_RX_3V3 I HCI UART data receive 9 HCI_TX_3V3 O HCI UART data transmit others Not connected J2 2 GND Connect to ground 7,9 +3V3 I Connect to +3.3V 8 PCM_OUT_3V3 O PCM data output 10 PCM_IN_3V3 I PCM data input 11 PCM_FSYNC_3V3 I/O PCM frame synch 17 PCM_CLK_3V3 I/O PCM clock 18 HCI_RTS_3V3 O HCI UART request-to-send 19 nSHUTD_3V3 I Shutdown input (active low) others Not connected
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 4 3333. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 5 This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: ZQ6-GT966X”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Navigation menu