AMPAK Technology WMCT759B CC2640RHB BLE module User Manual

AMPAK Technology Inc. CC2640RHB BLE module

User manual

Download: AMPAK Technology WMCT759B CC2640RHB BLE module User Manual
Mirror Download [FCC.gov]AMPAK Technology WMCT759B CC2640RHB BLE module User Manual
Document ID2882549
Application IDFrdSgibUfSCOiXNNOYExOQ==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize203.84kB (2548007 bits)
Date Submitted2016-01-25 00:00:00
Date Available2016-01-26 00:00:00
Creation Date2017-11-16 01:14:25
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-11-16 01:14:25
Document TitleMicrosoft Word - WMCT-759B Hardware & Software User Guide_V00.doc
Document CreatorPScript5.dll Version 5.2.2
Document Author: sean.yen

AMPAK
WMCT-759B
Hardware & Software Setup Guide
Rev. 0.0
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
1. Download & Install BLE-Stack
The latest BLE software can be downloaded at
http://www.ti.com/tool/ble-stack?DCMP=wbu-blestack&HQS=ble-stack.
After the BLE-Stack software installation is complete, the Prolific driver must
be associated with the device in order to use the BTool application.
2. Associate Prolific Driver with WMCT-759B
To associate the Prolific driver, you must first connect the WMCT-759B to the
PC’s USB port, or to a USB hub that connects to the PC.
Figure 1 Connect the WMCT-759B to the PC’ USB port
This section will guide you on how to install the PL-2303 Windows Driver. You
can download the latest Driver Installer program from Prolific Support
website:
http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
2.1 Power on your computer and boot to Windows. Run or double-click the PL-2303
Windows Driver Installer program.( e.g.PL2303_Prolific_DriverInstaller_v1.12.0.exe)
2.2 The InstallShield Wizard will be displayed to inform you that the PL-2303 USB-to-Serial
driver will be installed on your computer. Click Next to continue.
Figure 2 InstallShield Wizard
2.3 The PL-2303 Driver Installer program will then start to install the drivers needed.
Figure 3 Installer program
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
2.4 Click the Finish button to close the InstallShield program. If you have plugged the cable
into the PC while running the setup installation, please unplug and replug the cable for
the system to detect the device.
Figure 4 InstallShield Wizard Finish
2.5 Plug in the USB to Serial adapter to the PC USB port. Windows should detect the driver
as Prolific USB-to-Serial Com Port. Go to Device Manager and check for the “Prolific
USB-to-Serial Com Port” device and the COM port number assigned by Windows. See
the next section.
3. Determining the COM Port
You will need to know which COM port Windows has assigned to the serial port. To find
out, right-click on the “Computer” icon on your Start and select “Properties”, shown in
Figure 5.
Figure 5 Win7 PC, Finding Computer Properties
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
The “System” window should open up. Click “Device Manager”:
Figure 6 Win7 PC, Finding Device Manager
A list of all hardware devices should appear. Under the section “Ports (COM & LPT)”, the
port should appear.
Figure 7 Win7 PC, Connected Ports List
Take note of this port number, as it will be needed in order to use BTool. You may close the
device manager at this point.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
4. Starting the Application BToll
On Start-up you should be able to set the Serial Port Settings. Set the “Port” value to the
COM port earlier noted in Section 3. Baud rate select 115200. For the other settings, use the
default values as shown in Figure 8. Press “OK” to connect to the Host Board
Figure 8 BTool, Serial Port settings
When connected you should see the screen presented in Figure 9. The screen indicates that
you now have a serial port connection to the MWCT-759B Board.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
Figure 9 BTool, Overview
4.1 TX test
Step1. Select Adv. Command clicking to the “HCI” and found the “HCI_LETransmitterTest”.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
Step2. Before establishing a transmitter test, you will want to set up the desired
transmission parameters. After parameter setting, click “Send Command” button to begin
testing.
txChannel= (F-2402)/2
testDataLength= 37
testData=00
AMPAK Technology Inc.
Doc. NO:
; L(2402)=0 ; M(2440)=19 ; H(2480)=39
00=PRBS9 ; 01=11110000 ; 02=10101010
www.ampak.com.tw
Proprietary & Confidential Information
Step3 Change TX Channel
Step3.1. Select “HCI_LETestEnd” and click the “Send Command” button to end this test.
Step3.2. Select HCI_LETransmitterTest and change parameter of txChannel.
Click the “Send Command” button to begin testing.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
4.2 RX test
Step1. Select Adv. Command clicking to the “HCI” and found the “HCI_LEReceiverTest”.
reChannel= (F-2402)/2 ; L(2402)=0 ; M(2440)=19 ; H(2480)=39
step1.1: Press the “Send Command” button to perform RX test.
step1.2: Using instrument to transmission packets.
step1.3: Perform HCI_LETestEnd, in message log window can find the number of received.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
Step2. Change RX Channel
Please refer to Section 4.1 step 3.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
10
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
The product comply with the US portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in this
manual. The further RF exposure reduction can be achieved if the product can be
kept as far as possible from the user body or set the device to lower output power if
such function is available.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
11
This device is intended only for OEM integrators under the following
conditions:
1) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 1 condition above is met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for
any additional compliance requirements required with this module installed
IMPORTANT NOTE
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization
is no longer considered valid and the FCC ID can not be used on the final product.
In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: ZQ6-WMCT759B”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
12
第十二條→經型式認證合格之低 率射頻電機,非經許
自變更頻率
大 率或變更原設計之特性及 能
第十四條→低 率射頻電機之使用不得影響飛航安 及
時,應立即停用,並改善至無 擾時方得繼續使用
前項合法通信,指依電信法規定作業之無線電通信 低
業 科學及醫療用電波輻射性電機設備之 擾
,公司,商號或使用者均不得擅
擾合法通信;經發現有
率射頻電機須忍
擾現象
合法通信或工
模組請 註
1. 本模組於
2.
得認證後將依規定於模組本體標示審
系統廠商應於
AMPAK Technology Inc.
Doc. NO:
上標示
本產品
含射頻模組:
www.ampak.com.tw
合格標籤
CCAFXXLPXXXXTX)
Proprietary & Confidential Information
樣
13

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Author                          : sean.yen
Create Date                     : 2015:12:23 17:04:24+08:00
Modify Date                     : 2016:01:22 09:55:54+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Producer                        : GPL Ghostscript 9.07
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2016:01:22 09:55:54+08:00
Document ID                     : uuid:a93898c6-abaf-11e5-0000-0d74eb343f3f
Instance ID                     : uuid:b18fbf8d-5b01-447f-b1d9-9ea3f7c80a9a
Format                          : application/pdf
Title                           : Microsoft Word - WMCT-759B Hardware & Software User Guide_V00.doc
Creator                         : sean.yen
Page Count                      : 14
EXIF Metadata provided by EXIF.tools
FCC ID Filing: ZQ6-WMCT759B

Navigation menu