ARESON Technology BB0002 WIRELESS MOUSE User Manual b107 manual01

ARESON Technology Corp. WIRELESS MOUSE b107 manual01

USERS MANUAL

MiniWired / Wireless21inUser's GuideTrouble Shootinga. Make sure you have connected the receiver correctly to thecomputer's USB port.b. For the best performance, we suggest you to locate the receiverwith a distance from other electrical devices, such as the computer,the computer monitor or external storage drives.c. Make sure you have set the communication between the receiverand the mouse. Refer to the channel setting instruction (refer toNo.3)in your manual.d. Some system devices might conflict with the mouse. Confirm theIRQ/address settings of these devices for conflicts, and changethe settings as required.e. Make sure that you are not working the mouse on glossy orreflective surfaces.f. Try unplugging then reconnecting the receiver cable to yourcomputer.Battery use reminders1. Please make sure the batteries used for recharging are"Rechargeable Batteries"2. Remove worn-out batteries from equipment immediately anddispose of promptly.3. Keep all batteries (used or new) out of the reach of children.4. To have the batteries with a regular check and replace newbatteries if not used for a long time.5. Never dispose of batteries in fire, as they could explode.6. Always replace all the batteries at the same time. Mixing old andnew batteries or mining types (such as alkaline with zinc carbon)will reduce overall performance and could cause leakage or rupture.7. If the lower power indicator is blinking, please charge the batterythrough the USB charging cable immediately. Otherwise, you'llneed to re-set the ID and charge the batteries more than 6 hours.8. Do not mix different types of batteries (e.g. Ni MH, NiCd, alkaline,and etc) in the mouse.9. Remove batteries from the electrical device if the device is notgoing to be sued for a long time.10. If the performance of the batteries decreases substantially, it istime to replace the batteries.RecharegeableTOP5. Using as a Wired MouseIn addition to be a wireless, the mouse will be used as a regularoptical mouse.After setting well the ID channel, plug the receiver into the front sideof the mouse. According to the diagram introduction.Then, pull outthe retractable cable and plug it to an USB port, the mouse becomea wired optical mouse.When the receiver is plug into the socket, the battery is chargingwhen you're using the mouse.The receiver's face with the mark MUSTbe on the top, while plugging the receiver intothe front of the mouse.Before using as a wired mouse, please checkif the ID channel is well-set.PC USB portThis device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) this device may notcause harmful interference, and (2) this device must accept anyinterference received, including interference that may causeundesired operationFCC NOTE:The manufacturer is not responsible for any radio or TVinterference caused by unauthorized modifications to thisequipment. Such modifications could void the user's authority tooperate the equipment.
ID reset buttonReceiverID reset button /Led1. Insert the batteriesa. Remove the battery compartment cover on the back by pressingthe battery cover button of the mouse.b. Fit in the batteries according to the diagram indicated in thebattery cabinet.c. Close the battery compartment cover.2. Connect the receivera. Turn off your PC.b. Connect the receiver cable to USB port on PCc. Turn on your PCIt is a MUST to fully recharge the rechargeable batteries contained in this package atthe first-time use.The unit offers a strong power saving management. Once the mouse accesses thesleeping mode, " to click any button of the mouse" is compulsory to wake it up.Power on/off:1. To save the power, please turn off the mouse by pressing and holding the on/offswitch on the bottom of the mouse with 3-5 seconds.2. To turn on the power, just repeat the same step as above again.4. Recharge the batteriesTo charge the battery, plug the receiver into the front side of themouse, according to the diagram instruction. Then, pull out theretractable cable and plug it to an USB port, the mouse become awired optical mouse. When the receiver is plug into the socket, thebattery is charging when you're using the mouse.(ID reset button)Red Led indicatorblinks fasterGreen LED Light ON - RechargingGreen LED Light OFF - Recharging completedRed LED flashing - Low Power+-BatteriesBattery coverɘ!Mouse LED Display statusPCWheel buttonBattery coverID reset button/Power on/offswitchReceiverMouseReceiverLow power Led /Charging LedIntroductionCongratulations on your purchase of the World first 2-in-1 Miniwired/wireless rechargeable optical mouse, which includes opticaltechnology, the radio frequency technology. The mouse can be usedas a wirelsss mouse, and also as a wired mouse.The world first patented wired + wireless mouse27 MHz RFPlug the receiver to the front of the mouse to be a wired mouseBattery's recharged when the mouse is used as a wired mousePlug and Play! No need to set the channel ID2*AAA charging batteries included800 dpiPressPress Battery coverbuttonBattery coverbuttonThe red LED on the top cover of the mouse is a low batteries power indicator. Itindicates that batteries inside the mouse need to be recharged.If the batteries are used up, you may need to take out the batteries, reinstall again,and reset the ID to recharge it.The mouse surface may be warm during charging process. It is a normal phenomenon.NoteInstalling InstructionA wrong battery placementmay cause batteries overheat.(ID reset button)Red Led indicatorblinks slowly3. Establish communication between the mouseand receiverA. Auto-link mode:The mouse has auto-link function itself.B. Manual mode:a. Please reset the ID when first time use if necessary.b. Press the ID reset button on the topside of the receiver, and notethe red LED will blink slowly.(pic.1)c. Press the ID change button on the bottom of the mouse to set anew ID. (pic.2) The red LED indicator will blink at a faster ratewhen an identical ID is located.(pic.3)d. Press any button of the mouse to confirm the ID matching Thered LED indicator on the receiver will blink any time the mousesends it a signal.USB port123 4ID links OK!After Recharging1. Disconnect the recharging cable from the mouse when chargingis completed.2. Make sure the communication between the mouse and thereceiver is still available after completing recharging batteries. Ifnot, please refer to the channel setting instruction in the manualto reset the communication.

Navigation menu