ARRIS Global A5520N A5520N Home Network Interface System User Manual Manual 1

Pace Micro Technology plc A5520N Home Network Interface System Manual 1

Contents

Manual 1

A5500 Configuration Guide S r i R a m K i s h o r e F e b r u a r y 2 0 1 2
Table of contents Gateway Configuration ............................................................... 3 Accessing your gateway configuration tool................................................................... 3 Configuring your broadband Internet access ................................................................ 3 Configuring your local network ..................................................................................... 4 Configuring your wireless network ................................................................................ 5 Securing your wireless network .................................................................................... 7 Authorising programs to access the Internet ................................................................ 9 Configuring port forwarding ........................................................................................ 10 Defining a DMZ .......................................................................................................... 11 Configuring phone lines .............................................................................................. 11 Displaying the activated services ............................................................................... 13 Displaying the broadband status ................................................................................ 13 Home Network ........................................................................... 16 Displaying the devices connected to your gateway .................................................... 16 Administration ........................................................................... 17 Creating system password ......................................................................................... 17 Restarting your gateway ............................................................................................. 17 Restoring the factory settings ..................................................................................... 18 Displaying diagnostic information ............................................................................... 18 Using built-in IP utilities .............................................................................................. 19
GATEWAY CONFIGURATION Accessing your gateway configuration tool Connect a computer to your home gateway using an Ethernet cable or WiFi. Open an Internet browser and enter the "http://192.168.1.254" or “http://app.singnet.com.sg” web address to access your home gateway configuration tool. Configuring your broadband Internet access To configure your internet connection:  Under the Box heading, click Configuration, and then click Internet.  Select the Physical Link type:  If your broadband connectivity is through the Ethernet port of your gateway, leave the setting as Ethernet, which is the default.  If your broadband connectivity is through the ADSL port of your gateway, click ADSL.  Select your preferred Connection Protocol: DHCP (for Ethernet connectivity), PPPoE, or PPPoA (for ADSL connectivity).  If you set the connection protocol to PPPoE or PPPoA, enter the connection identifiers (PPP Login and PPP Password) given to you by your Internet service provider.  If you set the connection protocol to DHCP, you do not need to enter your username and password.  If necessary, change the DNS server address.  For configuring static IP address, select the Use the following IP address radio button in the EOA / IPoA Parameters panel. Enter the IP address, subnet mask, and default gateway in the respective text boxes.  Click OK to confirm. Note that your gateway then restarts to affect your changes.
Configuring your local network The default local IP address of your gateway is 192.168.1.254. The DHCP server is enabled by default and your connected hardware items will have an IP address in the range 192.168.1.1 to 192.168.1.253. The default lease time for an IP address is 240 minutes. To change these default settings:  Click LAN under the Configuration sub-heading. The LAN Configuration page shows up.  If necessary, change the IP address of your gateway and the subnet mask of your wireless network.  If necessary, change the IP address range. You can also change the default lease time, which represents the number of minutes you can use the assigned IP address before the DHCP lease expires.  To disable the DHCP server, click Disabled next to DHCP server. Some LAN clients require fixed IP addresses. For such clients, you must reserve and assign an IP address on the DHCP server. These reservations are permanent lease assignments, which are used to ensure that a specified LAN client on your network is always assigned the same IP address. To reserve an IP address for a LAN client:  Navigate to the Fixed IP addresses assigned by the DHCP server panel.  Click + Add a DHCP rule.
 Edit the default name of the LAN client, its MAC address, and the IP address you want to reserve for it.  Click OK to confirm. Configuring your wireless network Your gateway supports WiFi standard 802.11g and 802.11n, but is also compatible with standard 802.11b. To change your WiFi mode, click Wireless under the Configuration sub-heading. On the Wireless Configuration page that shows up, use the Wireless Mode drop-down list to change your WiFi mode:  802.11b: to connect with 802.11b devices only.  802.11g: to connect with 802.11g devices only.  802.11n: to connect with 802.11n devices only.  802.11b+g: to connect with both 802.11b and 802.11g WiFi device types.  80211g+n: to connect with both 802.11g and 802.11n WiFi device types.  80211b+g+n: to connect with all WiFi device types.  Auto: to let your gateway select the best WiFi mode. Note that, by default, your gateway is configured to allow wireless connections. You can disable this by setting Wireless State to Disabled. By default, your gateway automatically selects the best WiFi channel. However, you can select a channel manually.
Select an appropriate power level for your wireless connection from the Transmit Power drop-down box. The available range is 1 through 7. Higher the setting, higher is the power the transmitted signals and, therefore, coverage of your wireless network. The table below shows the relation between the transmit power value and its associated radio output power levels. Enter a name assigned to your wireless network in the Name of SSID text box. The default name is SINGTEL-XXXX, where XXXX represents the last four digits of your gateway serial number (for example, SINGTEL-1659). By default, your gateway broadcasts the SSID, which enables the visibility of your gateway to users who scan to connect to a wireless network. You can choose to disable the broadcast by selecting the Mask SSID check box. Note that when you disable the SSID broadcast, you will have to manually add a wireless profile in the LAN client to connect to your wireless network instead of selecting your SSID from a typical scan. Transmit Power Radio Output Power (dBm) 1 14 2 15 3 16 4 17 5 18 6 19 7 23
Securing your wireless network To secure your wireless network, click Wireless under the Configuration sub-heading. On the Wireless Configuration page that shows up, navigate to the Security panel. The default encryption type is WPA/WPA2, but you can choose another. The default WPA2 password is printed on the label on the right bottom side of your gateway.
The following table provides more information about the You can also secure your wireless network using the WiWPS is enabled, your gateway automatically detects the presence of a WPSclient; thus, simplifying the process of accessing your wireless networksupports both the WPS configuration methods: PIN(PBC) based. To set up WPS:  Select the Enable WPSmethod.  Click either the Push Buttongateway. You can then use the PUSH method on your LAN client (as advised by its manufacturer). The synchronization between the access point and the client shouldseconds. Authentication type DescriptionWEP The Wireless Encryption Protocol (WEP) is an older security protocol that allowsaccess your network without anprovides the least select this setting unless there is a compatibility issue with anolder wireless client. For added protection, set an encryption key on your accesswireless clients.Use the and WPA This setting provides good security and works with most wireless clients.access point and the wireless clientProtected Access encryption key.With WPA, you can use only (TKIPWPA2 This setting requires that wireless clients use only WPA2 to access yourthe access point and enteredcurrently tbe available on older wireless clients.With WPA2, you can use only the Standard WPA/WPA2 This setting allows a wireless client to use either WPAto access your network. An encryption key on the access pointwireless client.Use the (for clients that support WPA)WPA2)the setting as use the appropriate encryption mechanism depending on the wireless client.The following table provides more information about the supported encryption typesYou can also secure your wireless network using the Wi-Fi Protected Setup (WPS). When WPS is enabled, your gateway automatically detects the presence of a WPSprocess of accessing your wireless networksupports both the WPS configuration methods: PIN-based and Push Button Configuration Enable WPS check box. This enables the configuration of WPS using the PBCPush Button on the page or the WPS button on the front panel of your gateway. You can then use the PUSH method on your LAN client (as advised by its The synchronization between the access point and the client shouldDescription The Wireless Encryption Protocol (WEP) is an older security protocol that allows any wireless clients within the radio range to access your network without an encryption key. This setting provides the least level of security. For security select this setting unless there is a compatibility issue with anolder wireless client. For added protection, set an encryption key on your access point and enter the same key into your other wireless clients. Use the Select Option drop-down list to select between and 128-bit encryption mechanisms for WEP. This setting provides good security and works with most wireless clients. This setting requires an encryption key on the access point and the wireless client configured to use WiProtected Access – Pre-Shared Key (WPA-PSK) with the encryption key. With WPA, you can use only the Temporal Key Integrity ProtocolTKIP) encryption mechanism. This setting requires that wireless clients use only WPA2 to access your networks. An encryption key must be configured on the access point and entered into the wireless client. WPA2currently the most secure Wi-Fi encryption protocol bbe available on older wireless clients. With WPA2, you can use only the Advanced Encryption Standard (AES) encryption mechanism. This setting allows a wireless client to use either WPAaccess your network. An encryption key must be configured on the access point and the same key must be entered on the wireless client. Use the Select Option drop-down list to select between (for clients that support WPA) and AES (for clients that support WPA2) encryption mechanisms. We recommend you to leave the setting as Auto (default), which will enable your gateway to use the appropriate encryption mechanism depending on the wireless client. encryption types: Fi Protected Setup (WPS). When WPS is enabled, your gateway automatically detects the presence of a WPS-enabled LAN process of accessing your wireless network. Your gateway based and Push Button Configuration check box. This enables the configuration of WPS using the PBC button on the front panel of your gateway. You can then use the PUSH method on your LAN client (as advised by its The synchronization between the access point and the client should be complete within 120 The Wireless Encryption Protocol (WEP) is an older security any wireless clients within the radio range to encryption key. This setting level of security. For security reasons, do not select this setting unless there is a compatibility issue with an older wireless client. For added protection, set an encryption key ter the same key into your other down list to select between 64-bit This setting provides good security and works with most recent requires an encryption key on the configured to use Wi-Fi PSK) with the same Temporal Key Integrity Protocol This setting requires that wireless clients use only WPA2 to networks. An encryption key must be configured on into the wireless client. WPA2 is protocol but may not Advanced Encryption This setting allows a wireless client to use either WPA or WPA2 must be configured and the same key must be entered on the down list to select between TKIP (for clients that support encryption mechanisms. We recommend you to leave (default), which will enable your gateway to use the appropriate encryption mechanism depending on the
 If you want to use the PIN method instead, select box. Enter the PIN generated by the LAN client in the Enter PIN text box. Click establish the wireless connection. MAC address filtering is disabled by default. When enabled, the wireless connection is granted only to those LAN clients whose MAC addresses are registered. The Delivery Traffic Indication Message period (which the access point sends its broadcast traffic. Authorising programs to access the InternetYour gateway is, by default,This function may affect how some atools (email, chat, video conferencing, etc.), To allow some of your applications to  Under the Box heading, click  On the Configuring Applicationsdown lists.  Click OK to confirm. If you want to use the PIN method instead, select PIN from the WPS Methodbox. Enter the PIN generated by the LAN client in the Enter PIN text box. Click establish the wireless connection. MAC address filtering is disabled by default. When enabled, the wireless connection is granted only to those LAN clients whose MAC addresses are registered. The Delivery Traffic Indication Message period (DTIM Period) determines the interval at which the access point sends its broadcast traffic. Authorising programs to access the Internet , by default, configured to block all communications initiated from outside. This function may affect how some applications operate: online games, communication conferencing, etc.), and server applications (FTP, SMTP).To allow some of your applications to access your network from outsideheading, click Security, and then click ApplicationsConfiguring Applications page, select the applications you need WPS Method drop-down list box. Enter the PIN generated by the LAN client in the Enter PIN text box. Click Connect to MAC address filtering is disabled by default. When enabled, the wireless connection is granted only to those LAN clients whose MAC addresses are registered. ) determines the interval at communications initiated from outside. pplications operate: online games, communication server applications (FTP, SMTP). from outside: Applications. you need from the drop-
Configuring port forwarding The forwarding table allows all the packets received via a specific port to be transmitted to a specific machine on the internal network. Therefore, if you want to be able to access a web server operating on machine 192.168.1.135 from outside, you will have to define a forwarding rule that redirects all the TCP packets received via port 80 to another defined port on machine 192.168.1.135. To configure port forwarding:  Under the Box heading, click Security, and then click Port Forwarding.  On the Port Forwarding page, click + Add a Port Forwarding Rule.  If required, edit the default application name by clicking on it.  Select the protocol type: TCP or UDP.  Enter the port that has to be forwarded to the internal service.  Indicate the address of the hardware on the local network, followed by the destination port. The request will be forwarded to this private address.
Defining a DMZ The DMZ enables you to show a machine on the Internet with no restriction on the ports used. It allows you to open all previously undefined ports (port forwarding) to a single LAN machine:  Under the Box heading, click Security, and then click DMZ.  On the DMZ configuration page, click Enabled to enable the service.  Enter the IP address of the machine that will be in the DMZ. You can also select the name of the host from the drop-down list.  Click OK to confirm. Configuring phone lines You can configure one or two phone lines at a time on your gateway. In addition, you can configure the user name and password of your VOIP account to prevent unauthorized access. To configure your phone lines:  Under the Box heading, click Configuration, and then click Voice.  On the Router: Voice Configuration page, select the voice profile (singtel1 or singtel2) you want to edit or set up.  On the Line Configuration tab, click Line 1 or Line 2 and then select the Enable This Line checkbox. This activates the line for use.  Enter the Phone Number, Username, and Password provided by the Internet Service Provider in the corresponding text boxes.  Click Save Current Profile. Click OK in the confirmation window that pops up.  The page refreshes and status of the phone line along with a refresh button displays next to the Enable This Line checkbox:  Inactive or registering: Click the refresh button after some time. If the problem persists, verify the details you entered and try again.  Registration error: The phone lines have not been registered successfully. Verify the details you entered and try again.  Registered: The phone lines have been registered successfully.
After you successfully register your phone lines, you can click the Line Statistics tab to view detailed information such as the number of incoming and outgoing calls, duration of calls, etc.
Displaying the activated services Under the Box heading, click Status, and then click Services Status. This interface will allow you to view the services that are currently activated on your gateway. Displaying the broadband status Under the Box heading, click Status, and then click Broadband Status. This interface will allow you to view the connectivity status, Internet connection details, and traffic statistics. The following is an example of the Broadband Statistics page when the physical link is set to ADSL. For information on how to configure the physical link, see the “Configuring your broadband Internet access” section on page 3.
The following is an example of the Broadband Statistics page when the physical link is set to Ethernet.
HOME NETWORK Displaying the devices connected to your gateway To display the devices connected to your gateway, click Connected Devices under the Home Network heading. The devices that are currently connected and active are shown in green, whereas the devices that are not currently connected but have been part of your network are shown in red. You can view more information (such as IP address, MAC address, etc.) about the connected devices by hovering your mouse pointer over the hostname.
ADMINISTRATION Creating system password To set or change your gateway’s administrative password, click System Password under the Management heading. Note that the password is case-sensitive and must have at least 8 alpha-numeric characters. You can also include any of the following symbols: $ @ ! | & { } \ / ? Restarting your gateway To restart your gateway, click Restart under the Management heading. Your settings will be saved.
Restoring the factory settings To force your gateway to return to its original factory settings, click Reset under the Management heading. All your gateway settings will then be lost. Displaying diagnostic information To view detailed diagnostic information about your gateway and Internet connection, click Box Diagnostics under the Troubleshooting heading.
Using built-in IP utilities You can use the inbuilt IP utilities such as ping, traceroute, and dnsquery to determine if there are any communication issues between your gateway and the host/Internet. To access these utilities:  Under the Administration heading, click Troubleshooting, and then click IP Utilities.  Select the test you want to run from the Test Type drop-down list:  If you select ping, you can test whether a particular host is reachable across an IP network. In addition, you can self-test the network interface card of your gateway or use the tool for latency test.  If you select traceroute, you can determine the route taken by the data packets across an IP network.  If you select dnsquery, you can test if your gateway is resolving domain names to IP addresses.  Enter the IP address of the destination in the Host Address text box.  Click Start or Stop testing. You can view the results in the Test Results text box.  To clear previous test logs, click Clear Results.

Navigation menu