ARRIS Global RNG210N Set-top Box with Moca Model:RNG210N User Manual Manual
Pace Micro Technology plc Set-top Box with Moca Model:RNG210N Manual
Manual
BRINGING TECHNOLOGY HOME
www.pace.com
USER GUIDE
Pace RNG210N
1
CONTENTS
This product incorporates copyright protection technology that is protected by
U.S. patents and other intellectual property rights. Use of this copyright protection
technology must be authorized by Rovi Corporation, and is intended for home and
other limited viewing uses only unless otherwise authorized by Rovi Corporation.
Reverse engineering or disassembly is prohibited.
SAFETY INFORMATION .............................................................................................2
IMPORTANT SAFETY INSTRUCTIONS .......................................................................3
Regulatory information ........................................................................................7
REAR PANEL ..............................................................................................................8
CONNECTING THE EQUIPMENT .............................................................................10
Setup A - Home theater system with HDTV
(HDMI connection) ............................................................................................11
Setup B - Home theater system with HDTV
(Component video / YPbPr connection) ............................................................11
Connecting the power supply unit to your set-top .............................................14
Connecting equipment to the wall AC outlets ....................................................14
Lightning storms ...............................................................................................15
Turning your set-top on and off..........................................................................15
Pairing your remote control with your set-top ....................................................16
FRONT PANEL .........................................................................................................17
TERMS AND CONDITIONS FOR USE OF SOFTWARE (“TERMS”)............................18
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
CableCARD™ is a trademark of Cable Television Laboratories, Inc.
Other trademarks listed herein are the property of their respective owners.
© 2011 Pace plc.
All rights reserved.
Pace and are trademarks and/or registered trademarks of Pace plc
2
SAFETY INFORMATION
This digital set-top has been manufactured and tested with your safety in
mind. However, improper use can result in potential electric shock or fire
hazards. To avoid defeating the safeguards that have been built into your
set-top, please observe the precautions discussed in this document.
Do not perform any servicing unless you are qualified to do so. Refer all
servicing to qualified service personnel. Servicing the set-top yourself will
invalidate the warranty.
To reduce the risk of fire or electric shock, do not expose this set-top to rain
or moisture.
On the rear panel of your set-top there is a tamper-evident label that states
‘Warranty void if broken or removed’.
To avoid possible damage to the internal hard disk, do not pick up or move
your set-top while it is connected to the power supply. If you want to move
your set-top, first stop any recording, then turn off your set-top and wait 60
seconds before disconnecting it. You should handle your set-top carefully, as
any damage you cause to the internal hard disk (or any other component) will
invalidate your warranty.
Installation
The installation of your set-top should be carried out by a qualified installer
and should conform to local codes.
Note to the installer
This reminder is provided to call the attention of the cable-TV-system
installer to Section 820 of the National Electrical Code (USA), which
provides guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as is practical.
To ensure correct operation, use this set-top only with the Pace-approved
power supply unit provided. If you use an unapproved alternative, you will
invalidate the warranty.
Other warnings
To reduce the risk of electric shock, do not remove the cover of your set-top.
There are no user-serviceable parts inside it.
The lightning flash with arrowhead symbol, within a triangle,
is intended to alert you to the presence of uninsulated
“dangerous” voltages within your set-top’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock
to persons.
The exclamation point within a triangle is intended to alert
you to the presence of important instructions in the literature
accompanying your set-top.
Warnings on the power supply
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
3
IMPORTANT SAFETY INSTRUCTIONS
Before you install or use the apparatus, you must read and
understand these Important Safety Instructions.
At all times when using the apparatus you must follow these
Important Safety Instructions to reduce the risk of fire, electrical
shock and injury to persons.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into the outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Service address:
Pace Americas Inc.
3701 FAU Boulevard, Suite 200, Boca Raton, Florida 33431 U.S.A.
4
SAFETY INFORMATION (cont.)
In addition to the Important Safety Instructions, please read the Safety
Information below.
Power sources
The model number, serial number, and electrical rating of this set-top are on
a label on its base.
You must operate your set-top only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to
your home, consult your dealer or local power company. If you move your
set-top between locations at different temperatures, allow it to reach room
temperature before you apply power to it.
Overloading
Do not overload wall AC outlets, extension cords or other power outlets as
this can result in a risk of fire or electric shock.
Lightning
For added protection for your set-top during a lightning storm, or when
it is left unattended and unused for long periods of time, disconnect the
cable system from your set-top. See also item 13 in the Important Safety
Instructions.
Ambient temperature
The operating temperature range of your set-top is 32-104°F. If the ambient
temperature around your set-top falls outside this range, you must correct
this in order for your set-top to work correctly and safely. For example, if the
temperature is too high, make sure there is sufficient ventilation (see below)
and that your set-top is not directly on top of or underneath other equipment.
Ventilation
Slots and openings in the casing of your set-top are provided for ventilation,
to ensure reliable operation of your set-top and to protect it from overheating.
• Neverblocktheventilationopeningsbyplacingyourset-toponabed,
sofa, rug, or other similar surface. Place it on a hard, flat surface.
• Nevercovertheventilationopeningswithitemssuchasnewspapers,
table-cloths, or curtains.
• Youcanplaceyourset-topnearotherconsumerelectronicsdevices,such
as stereo amplifiers or televisions, but you must not place it directly on
top or underneath them.
• Donotplaceyourset-topinabuilt-
in installation such as a bookcase
or rack unless proper ventilation is
provided and you have adhered to
the manufacturer’s instructions.
• Maintain a minimum
distance of three inches
around your set-top for
sufficient ventilation.
See also item 7 in the Important Safety
Instructions.
3 in. 3 in.3 in.
5
SAFETY INFORMATION (cont.)
Water and moisture
Do not expose your set-top to rain or moisture, dripping or splashing, and
ensure that no objects filled with liquids, such as vases, are placed on your
set-top. See also item 5 in the Important Safety Instructions.
Entry of objects and liquids
Never push objects of any kind into your set-top through openings as they
may touch dangerous voltage points or short-out parts that could result in
fire or electric shock. Never spill liquid of any kind on your set-top.
Transporting
Move the combination of set-top and cart with care. Quick stops, excessive
force and uneven surfaces may cause the combination of set-top and cart to
overturn. See also item 12 in the Important Safety Instructions.
Placement and mounting
Do not place your set-top on an unstable or uneven surface. Your set-top
may fall, causing serious injury to a child or adult and serious damage to
your set-top. If you mount your set-top, for example to a wall or ceiling,
follow the manufacturer’s instructions and use a mounting accessory
recommended by the manufacturer. See also item 12 in the Important Safety
Instructions.
Risk of fire or scorching
Never place naked flame sources, such as lighted candles, on or adjacent to
your set-top.
Replacement parts
When replacement parts are required, be sure that the service technician has
used replacement parts specified by the manufacturer or that have the same
characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock or other hazards. See also item 14 in the Important Safety
Instructions.
Safety check
Upon completion of any servicing or repairs to your set-top, ask the service
technician to perform safety checks to determine that your set-top is in
its proper operating condition. See also item 14 in the Important Safety
Instructions.
SAVE THIS INFORMATION FOR FUTURE REFERENCE
6
SAFETY INFORMATION (cont.)
Safety aspects of connections
Full details of the rear panel are on pages 8 and 9.
Connecting
Do not connect your set-top (or any other equipment such as a TV or VCR)
to the power supply until you have properly connected all the other cables.
Your set-top is designed for use only with the power supply unit provided.
On the power supply unit there is a label that specifies the correct AC power
supply input for it. Do not connect the power supply unit to any supply other
than this.
Always connect the 15 volt DC cord from the power supply unit to your
set-top before you insert the AC power cord from the power supply unit into
the wall AC outlet.
Disconnecting
To disconnect power from your set-top, always detach the power supply
unit from the wall AC outlet (rather than remove the 15 volt cord from your
set-top).
Therefore you must install your set-top near to the wall AC outlet, which
should be easily accessible.
If you are in any doubt about the power supply cord, its plug or its
connection, consult a qualified electrician.
The CABLE IN connector is designed
for connection to a cable network only.
You must not connect any other
equipment, such as a VCR, to this input.
POWER INPUT
15 volt power
supply unit
To ensure correct
operation, use this
set-top only with the
Pace-approved power
supply unit provided. If
you use an unapproved
alternative, you will
invalidate the warranty.
7
SAFETY INFORMATION (cont.)
Regulatory information
CAUTION: Do not attempt to modify your set-top without written
authorization from the manufacturer. Unauthorized modification
could void your authority to operate your set-top.
NOTE
Your set-top has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. Your set-top generates, uses
and can radiate radio-frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If your set-top does cause harmful interference to
radio or television reception, which can be determined by turning your
set-top off and on, you are encouraged to try to correct the interference by
one or more of the following measures.
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweenyourset-topandthereceiver.
• Connectyourset-toptoanoutletonacircuitdifferentfromthatto
which the receiver is connected.
• Consultyourdealeroranexperiencedradio/TVtechnicianforhelp.
8
REAR PANEL
COMPONENT VIDEO
Component video output
for analog HDTV
AUDIO OUT
Audio outputs (stereo, L and R)
CABLE IN
From cable
service-provider
1394
For connection to a
1394-compatible device
eSATA
For connection to an optional
external hard disk (if enabled).
POWER INPUT
(Make this
connection
last of all)
DIGITAL AUDIO
Optical S/PDIF audio output
ETHERNET
For connection
to a home
network
(if enabled)
HDMITM
Video and audio output for
digital HDTV.
Also an input (if enabled).
USB port
For connection to USB device
(if enabled)
CableCARD™ module
(behind cover) Removal
will interrupt your service
9
REAR PANEL (cont.)
CABLE IN Connect the cable service here.
1394 Connect to a TV with a 1394 port or to any other 1394-compatible device.
COMPONENT VIDEO If your HDTV does not have an HDMI connector, connect your HDTV here.
AUDIO OUT Connect to the L and R audio inputs on your stereo TV, stereo VCR, or optional stereo amplifier.
DIGITAL AUDIO Connect to the optical digital audio input on optional digital audio equipment, such as an audio decoder or home theater
receiver.
HDMI Out Connect your HDTV here for a digital audio/video connection (instead of using the component video connectors).
HDMI In If this connector is enabled by your cable service-provider, you can connect another HDMI device (allowing that device’s
output to loop through the set-top to the TV).
CableCARD module Removal will interrupt your service.
USB port If this port is enabled by your cable service-provider, you can connect compatible optional equipment that supports a USB
2.0 interface.
eSATA If this connector is enabled by your cable service-provider, you can connect an optional external hard disk.
ETHERNET If this connector is enabled by your cable service-provider, you can connect your set-top into an Ethernet home network.
+15V POWER Connect your set-top’s power supply unit here. Make this connection last of all.
10
CONNECTING THE EQUIPMENT
In order for you to view programs broadcast in high-definition, your set-top must be connected to a suitable HDTV
or computer monitor.
Your equipment should have been connected up by your installer. However, if you need to disconnect and
reconnect your equipment, read pages 10 through 14.
On pages 12 and 13, there are two typical connection setups for an HDTV, DVD player, and home theater receiver.
These setups make efficient use of the connectors on your set-top. However, depending on your other equipment
and the connectors on it, the person who installed your system may have chosen to connect things differently.
Both setups allow play-back of DVDs. You hear stereo sound from the home theater’s loudspeakers.
You can take advantage of the digital audio output from your set-top by connecting a suitable cable between your
home theater receiver and the DIGITAL AUDIO connector (as shown in the diagram).
WARNINGS
Do not connect your set-top (or
any other equipment such as a TV
or VCR) to the power supply until
you have properly connected all
the other cables.
Disconnect your set-top’s power
supply unit from the AC power
supply before you disconnect any
other equipment from its rear
panel.
The only way to disconnect your
set-top from the AC power supply
is to remove the power supply unit
from the wall AC outlet (or switch
the wall AC outlet switch, if present,
to its OFF position). Your set-top
must therefore be installed near to
the wall AC outlet,
The cable input is designed for
connection to a cable network
only. You must not connect any
other equipment, such as a VCR,
to this input.
11
CONNECTING THE EQUIPMENT (cont.)
Setup A - Home theater system with HDTV
(HDMI connection)
Setup A (see page 12) uses an HDMI connector to connect to the HDTV. This displays the highest quality picture
on the HDTV and also means there will be no picture degradation on any copy-protected programs (provided the
link remains secure – see right).
Setup B - Home theater system with HDTV
(Component video / YPbPr connection)
Setup B (see page 13) uses a component video connection to connect to the HDTV. This displays a high definition
picture on your TV.
NOTE
How you set up your equipment may depend on your home theater receiver. For example, the optical audio
input may be associated with a particular video input. Consult your home theater user guide for further details.
NOTE
Copy protection via an HDMI
secure link
The HDMI link between your set-
top and your HDTV should be a
secure link. When your set-top is
attached via an HDMI cable to an
HDCP-compliant (High-bandwidth
Digital Content Protection) HDTV,
the HDTV and set-top negotiate
a secure link, which allows your
set-top to transmit full resolution
video (picture) to your HDTV.
Not all HDTVs support HDCP. If
your set-top is connected to an
HDTV that does not support it, you
may see a solid-red screen or a
message similar to the following:
Your HDTV does not support HDCP.
Please use the YPbPr component
connection to watch TV.
The HDMI output is then disabled,
so no picture is transmitted from
this connector. In that case, use
the component video connectors
to connect up (see Setup B).
12
CONNECTING THE EQUIPMENT (cont.)
DVD
PB/CB
PR/CR
Y
COMPONENT
VIDEO OUT
DIGITAL AUDIO OUT
OPTICALCOAXIAL
COMPOSITE
VIDEO OUT
OPTICAL
AUDIO IN
COAXIAL
AUDIO IN
DIGITAL AUDIO IN
HOME
THEATER
RECEIVER
LEFT
AUDIO
RIGHT
AUDIO
VIDEO
LEFT
AUDIO IN
VCR IN
RIGHT
AUDIO IN
VIDEO IN
ANTENNA/
RF IN
HDMI
PB IN
PR IN
Y IN
COMPONENT
VIDEO IN
LEFT
AUDIO IN
RIGHT
AUDIO IN
VIDEO IN
HDTV
POWER
POWER
POWER
WALL AC OUTLET
WALL AC OUTLET
WALL AC
OUTLETS
CABLE INPUT
Setup A: (HDMI)
13
DVD
PB/CB
PR/CR
Y
COMPONENT
VIDEO OUT
DIGITAL AUDIO OUT
OPTICALCOAXIAL
COMPOSITE
VIDEO OUT
OPTICAL
AUDIO IN
COAXIAL
AUDIO IN
DIGITAL AUDIO IN
HOME
THEATER
RECEIVER
LEFT
AUDIO
RIGHT
AUDIO
VIDEO
LEFT
AUDIO IN
VCR IN
RIGHT
AUDIO IN
VIDEO IN
ANTENNA/
RF IN
HDMI
PB IN
PR IN
Y IN
COMPONENT
VIDEO IN
LEFT
AUDIO IN
RIGHT
AUDIO IN
VIDEO IN
HDTV
POWER
POWER
POWER
WALL AC OUTLET
WALL AC OUTLET
WALL AC
OUTLETS
CABLE INPUT
Setup B: (Component video)
CONNECTING THE EQUIPMENT (cont.)
14
WARNINGS
Do not connect your set-top (or any other equipment such as a TV or VCR) to the AC power supply until you
have properly connected all the other cables.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
Connecting the power supply unit to your set-top
Before you insert the power supply unit into the wall AC outlet, connect the 15 volt DC cord from the power supply
unit to the socket labeled “+15 V 4.0 A MAX” on your set-top’s rear panel.
Connecting equipment to the wall AC outlets
Connect your set-top’s power supply unit, and the plugs on the power cords from your TV, DVD, and any other
equipment, into wall AC outlets. If these outlets have switches, switch them ON.
CONNECTING THE EQUIPMENT (cont.)
15
CONNECTING THE EQUIPMENT (cont.)
Lightning storms
Disconnect your set-top’s power cord during lightning storms. A lightning storm may affect your set-top, if it is on
during the storm. It may appear that it has stopped working, but you can easily restore its operation as follows:
Unplug your set-top’s power supply unit from the wall AC outlet. Then plug this power supply unit in again at the
wall AC outlet (and, if there is a switch by this outlet, switch it to its ON position).
Turning your set-top on and off
After you have connected your set-top’s power supply unit to the wall AC outlet (and switched this outlet ON, if it
has a switch), press the POWER button on your remote control to turn your set-top on (you will need to pair your
remote control with your set-top first - see page 16). The (power) light on your set-top’s front panel should
light up blue, to show that your set-top is on.
To turn your set-top on or off at any time, press the POWER button on your remote control.
Never turn off your set-top by simply disconnecting it from the power supply. If you need to disconnect your
set-top, first stop any recording (if applicable). Then turn off your set-top by pressing the POWER button on your
remote control, so that the (power) light goes off. Then wait 60 seconds before removing the power supply unit
from the wall AC outlet.
Power Saving: To save power and money, and to reduce greenhouse gas emissions, turn off your
set-top, using the power button, when it is not in use.
A blue light around
the button turns on.
To turn your set-top on,
press the power button.
Front panel display,
showing the time.
16
Pairing your remote control with your set-top
Before using your set-top with your TV, you must pair your remote control with your set-top.
1. Put the two AA batteries provided into your remote control.
2. Turn on your TV and set-top.
3. Press and hold the two buttons (the select buttons) on the front of your set-top. You’ll see a message on
your TV showing you that your set-top is trying to pair with a remote control. Your TV shows you which two
buttons to press on your remote control.
4. Press and hold the two buttons on your remote control, as instructed on your TV screen. You’ll see a message
on your TV confirming that your remote control has been paired with your set-top.
NOTE
If you don’t complete the process within two minutes, you’ll have to start again. Pressing EXIT on your remote
control also ends the pairing process.
CONNECTING THE EQUIPMENT (cont.)
NOTES
Your cable TV service-provider
determines the digital channels,
services, and screen information
that you see on your TV when you
use your set-top and its remote
control.
Consult the information supplied
by your cable service-provider for
details on how to make the most of
the digital cable services. Also read
the operating instructions that are
supplied with your remote control.
17
FRONT PANEL
Power button
To turn your set-top
on/off.
(power) light
Lights blue when your set-top
is on and is not lighted when
your set-top is off.
Display
Shows the time or the current
channel number, and the setting
when you make user settings.
USB port
(If enabled by your
cable service-provider.)
Select buttons
To perform remote
control pairing.
18
THE PRODUCT TO WHICH THESE TERMS RELATE (THE “PRODUCT”) INCORPORATES
SOFTWARE WHICH IS OWNED BY PACE plc (“PACE”) OR ITS THIRD PARTY LICENSORS
(THE “SOFTWARE”). BEFORE USING THE PRODUCT PLEASE READ THESE TERMS.
IF YOU DO NOT AGREE TO THESE TERMS YOU MAY NOT USE THE PRODUCT AND
SHOULD IMMEDIATELY RETURN THE PRODUCT TO YOUR SUPPLIER. THESE
TERMS ALSO APPLY TO ANY MODIFICATIONS, UPDATES OR SUPPLEMENTS TO THE
SOFTWARE PROVIDED TO YOU. FOR PURPOSES OF THESE TERMS, “YOU” MEANS
YOU, THE END USER, AND YOUR PRODUCT SUPPLIER, UNLESS THE CONTEXT
REQUIRES OTHERWISE.
A. License Grant and Conditions
1. Pace, or your supplier, if applicable, grants you a non-exclusive, non-transferable,
limited license to use the Software solely as integrated with, incorporated into, or
provided for use in connection with the Product.
2. Pace reserves all rights not expressly granted to you under these Terms.
3. You may not transfer any of your limited rights in the Software without the prior
written consent of Pace, and if consent is provided then the Software shall only
be transferred in conjunction with the transfer of the Product AND ONLY IF the
transferee has read and agreed to accept these Terms.
4. You must ensure that the copyright, trademark and other protective notices contained
in the Software are maintained and not altered or removed.
5. The Software is protected by copyright and other laws and international copyright
and other treaties.
6. The Software provided hereunder is licensed (not sold). Pace is NOT transferring title
or any ownership rights in the Software to you.
7. All title and intellectual property rights in and to the Software and all modifications,
updates, enhancements and derivative works of the Software are owned exclusively
TERMS AND CONDITIONS FOR USE OF SOFTWARE (“TERMS”)
by Pace or its licensors and you agree to execute any document reasonably
requested by Pace to evidence such ownership rights.
8. Certain third party software used in connection with the Product may be made
directly available to you by operating system or other third party providers. Use of
such Software is also subject to the terms of any applicable agreement between you
and such third party.
B. License Restrictions
Except as expressly permitted herein or by statute you may not:
1. use the Software in conjunction with any other hardware or equipment other than the
Product;
2. copy or modify all or any portion of the Software;
3. incorporate all (or any portion of) the Software into other programs developed or
used by (or on behalf of) you;
4. reverse engineer, decompile, decrypt or disassemble the Software (or any portion of
the Software); or
5. export, transfer or re-export the Software in violation of any applicable law.
C. Open Source Software
Certain components of the Software are subject to either:
(i) the GNU General Public Licence (“GPL”);
(ii) the GNU Lesser General Public Licence (“LGPL”); or
(iii) OpenSSL license.
The foregoing are not subject to the restrictions in Section B. In compliance with the GPL
and LGPL Pace makes the source code of the Linux software, libraries and associated
utilities it uses, together with its modifications (if any), available to the public in source
code form at: http://www.pace.com/opensource/request.
19
You are free to use, modify and distribute the Linux software and any modifications as
long as you comply with the terms of the GPL or LGPL referred to above. The License
terms applicable to (i) to (iii) above are available to you, as explained in the section below
entitled Open Source Licenses.
The Software also contains the following:
(iv) SHA library Copyright © 2000-2001, Aaron D. Gifford All rights reserved.
(v) Expat XML Parsing Library
Copyright © 1998, 1999, 2000 Thai Open Source Software Centre Ltd and Clark Cooper.
Copyright © 2001, 2002, 2003 Expat maintainers.
(vi) Expat++ This component of the Software is subject to the Mozilla Public License Version
1.0.
(vii) Base64 Algorithm Copyright © 2001 Bob Trower, Trantor Standard Systems Inc.
Certain additional license terms applicable to (iv) to (vi) above are available to you, as
explained in the section below entitled Open Source Licenses.
D. Termination
These Terms are effective until terminated. You may terminate these Terms by returning
the Product to your supplier. These Terms will terminate automatically without notice
if you fail to comply with these Terms or any other written agreement between you and
Pace. Upon termination you must return the Product to your supplier.
E. Disclaimer
1. EXCEPT AS SET FORTH IN ANY WRITTEN AGREEMENT BETWEEN YOU AND
PACE (OR YOUR SUPPLIER), THE SOFTWARE IS (TO THE EXTENT PERMITTED BY
LAW) SUPPLIED “AS IS” AND PACE AND ITS LICENSORS EXPRESSLY EXCLUDE
ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING (BUT NOT LIMITED TO)
WARRANTIES OF MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR
PURPOSE AND NON-INFRINGEMENT.
TERMS AND CONDITIONS FOR USE OF SOFTWARE (“TERMS”) (cont.)
2. EXCEPT AS SET FORTH IN ANY WRITTEN AGREEMENT BETWEEN YOU AND
PACE, IN NO CIRCUMSTANCE WILL PACE BE LIABLE FOR ANY DIRECT, INDIRECT,
CONSEQUENTIAL, SPECIAL, PUNITIVE OR INCIDENTAL DAMAGE (INCLUDING
LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA OR THE COST OF
PROCUREMENT OF SUBSTITUTE GOODS, TECHNOLOGY OR SERVICES) ARISING
OUT OF THE USE OR THE INABILITY TO USE THE SOFTWARE.
F. General
These Terms are governed by the laws of the State of New York and you may only bring
claims exclusively in New York courts and Pace shall be entitled to bring a claim in the
courts of any jurisdiction. Any failure by Pace to enforce any of its rights hereunder or
applicable law shall not constitute a waiver of such rights. Pace’s licensors and suppliers
shall be third party beneficiaries of this License Agreement, as applicable.
YOUR USE OF THE PRODUCT CONSTITUTES YOUR ACKNOWLEDGEMENT THAT YOU
HAVE READ THESE TERMS AND AGREE TO BE BOUND HEREBY.
Open Source Licenses
The software contained in this product may be covered by certain components consisting
of free software or open source software. A list of these components and a copy of the
relevant copyright notices and license term notices that are required by such licenses are
available at this web page:
http://www.pace.com/opensource/license
This list may change from time to time and may depend on the model of product or the
version of software you have received. If you are unable to access this web page and
wish to have a copy of this list, please contact the Open Source Administrator at: 3701
FAU Boulevard, Suite 200, Boca Raton, Florida 33431 USA. To the extent the terms of
these open source or free software licenses prohibit any of the restrictions in any end user
license included with the product, such restrictions will not apply to the applicable open
source or free software component.
20
NOTES
21
NOTES
501-3443200
Pace and are trademarks and/or registered trademarks of Pace plc.
www.pace.com