ASSALOY Global Solutions Norway AS 681402004 Bluetooth Low Energy Module User Manual

ASSA ABLOY Hospitality AS Bluetooth Low Energy Module

User Manual

Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 1 (13) ASSA ABLOY HOSPITALTY AS. ASSA ABLOY Installation of BLE Module 681402004
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 2 (13) ASSA ABLOY HOSPITALTY AS. Copyrights The information in this document is subject to change at the sole discretion of ASSA ABLOY Hospitality AS without notice. Any use, operation or repair in contravention of this document is at your own risk. ASSA ABLOY Hospitality AS does not assume any responsibility for incidental or consequential damages arising from the use of this manual. All information and drawings in this document are the property of ASSA ABLOY Hospitality AS. Unauthorized use and reproduction is prohibited. VingCard is a registered trademark of ASSA ABLOY Hospitality AS.
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 3 (13) ASSA ABLOY HOSPITALTY AS. Installation of BLE Module 681402004 BLE Module 681402004 is only used in Assa Abloy Hospitality AS products. The BLE Module 681402004 is factory mounted in the Assa Abloy Hospitality AS products which in this document are referred to as “The Host System”. In addition, the BLE Module can be installed on Assa Abloy Hospitality AS existing installed products at our customer’s locations. These updates are solely carried out by Assa Abloy Hospitality Engineers. The customer or end user of the BLE Module have no contact with the Module as it is unseen to the end user so there are no special precautions the customer needs to take in terms of installing or usage of BLE Module 681402004. Each manual for the different Assa Abloy Hospitality AS end products, in which the BLE module 681402004 is installed, will contain the FCC and Industry Canada statements given below. FCC statements FCC (Federal Communications Commission) statements This device comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) The BLE Module may not cause harmful interference, and 2) The BLE Module must accept any interference received, including interference that may cause undesired operation. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Important Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This transmitter must not be co-located or operating in conjunction with any other antennas or transmitters.
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 4 (13) ASSA ABLOY HOSPITALTY AS. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The concerned end product must be labeled to say “Contains FCC ID: Y7V-681402004” Industry Canada statements This device comply with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1) The BLE Module may not cause interference, and 2) The BLE Module must accept any interference, including interference that may cause undesired operation of the device. Important note: To comply with Industry Canada RF radiation exposure limits for general population, the antennas used for these transmitters are exempted from Routine Evaluation Limits – SAR Evaluation in accordance with RSS-102 section 2.5.1. The concerned end product must be labeled to say “Contains IC: 9514A-68102004” Déclarations d’Industry Canada Cet équipement est conforme aux normes d’exemption de licence RSS d’Industry Canada. Son utilisation est soumise aux deux conditions suivantes: 1) Le module BLE ne doit pas provoquer d’interférence, et 2) Le module BLE doit accepter toute interférence, y compris des interférences susceptibles de provoquer un fonctionnement indésirable de l’équipement. Remarque importante : Pour respecter les limites d’exposition aux radiofréquences d’Industry Canada pour le grand public, les antennes utilisées pour ces émetteurs-transmetteurs sont exemptées des limites d’évaluation de routine – évaluation SAR, conformément à la norme RSS-102 section 2.5.1. Le produit final concerné doit porter une étiquette avec la mention: “Contient IC: 9514A-68102004”
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 5 (13) ASSA ABLOY HOSPITALTY AS. BLE Module 681402004 Installation Since the BLE Module 681402004 is not and will not be supplied to the end user on its own and the BLE Module 681402004 will only be installed and or replaced on the Host Systems by Assa Abloy Hospitality AS Engineers; only a quick generic installation guide of the BLE Module 681402004 to the Host System is given. Following parts are needed to connect BLE Module to the Host System ITEM NO. PART NUMBER DESCRIPTION QTY. 1 683081114 Y-Cable Zigbee Endnode Classic Assy. 1 2 4825976 Cable Sleeve 1 3 4825793 Housing BLE 1 4 4825796 Shield BLE 1 5 4825943 Screw Standoff 2 6 681402004 BLE Module 1 7 4826006 Host System label with information of installed BLE 1
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 6 (13) ASSA ABLOY HOSPITALTY AS. Installation Procedure Y-Cable Zigbee Endnode Classic Assy. and Cable Sleeve BLE Housing, Shield BLE, & Screw Standoff 6) BLE Module Insert the Cable Sleeve on the side of Y-Cable Zigbee Endnode Classic Assy. cable to be connected to the “BLE Module”. Thread the cable via the Shield BLE and Housing BLE; connect the Y-Cable to the BLE Module. Mount the BLE Module in the Housing, and cover it with the Shield. Mount the Screw Standoff. 2) Cable Sleeve 1) Y-Cable Zigbee Endnode 3) Housing BLE 4) Shield BLE 5) Screw Standoff Interfaces to the Host System Interface to BLE Module
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 7 (13) ASSA ABLOY HOSPITALTY AS. A mounted BLE Module in the housing and Y-Cable connected BLE Module with Y-Cable connected and Screw Standoff mounted, covered by the BLE shield. Thread the rest of Y-cable which will go to the Host System through the door, alien the Screw standoff, connected the Y-cable to the appropriate connectors on the Host system. To Host System Y-Cable connected to the Host System Battery pack 4.5V
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 8 (13) ASSA ABLOY HOSPITALTY AS. 7)Host system label concerning BLE The Host System label indicating the presence of the BLE module in the system should be attached as indicated: Installed the Back Host System cover Front Host system Back Host System Cover Host Label indicating the presence of BLE module with FCC and IC Identification
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 9 (13) ASSA ABLOY HOSPITALTY AS. BLE Module Replacing Procedure The only tool need is Screwdriver Torx T20S for removing the screws on the Host System. Remove the Host System Cover. Disconnect the Y-Cable connectors (coming from the BLE module) from the Host System, and remove the Host System screws connected to BLE module item 5: Screw standoff. Y-Cable connected to the Host System Screws connected to BLE Module Screw standoff.
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 10 (13) ASSA ABLOY HOSPITALTY AS. From the front side of the Host system, pull out the unit where BLE module is mounted. Unmount the BLE shield. Disconnect the Y-cable from the BLE Module Remove the BLE Module from the BLE housing and replace it. Unmount the BLE shield
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 11 (13) ASSA ABLOY HOSPITALTY AS. Viewing FCC an IC information label on the Host System All Host Systems where a BLE Module is installed; has an attached label with FCC and IC identities. To gain access to this label once the module has been installed in the Host System, the only tool need is a Torx T20s screwdriver, which is readily available from any hardware store. Following procedure should be followed to gain access to the label: The Host System Use Torx T20s screwdriver and open the Host System Back cover to access the label Back Host System Front Host System
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 12 (13) ASSA ABLOY HOSPITALTY AS. After opening the Back Cover, the Label can be accessed BLE Module 681402004 Operation BLE Module 681402004 operates only on Assa Abloy Hospitality Host Systems, and is solely installed, maintained, and debugged by Assa Abloy Hospitality Engineers. BLE Module Specifications Radio technologies utilized BLE [Bluetooth low energy] Frequency ranges of operation 2.400 GHz-2.4835 GHz Channel plan 40 2-MHz channels Transmitter antenna gain 3.5dBi, Impedance 50 ohm Antenna Type Inverted F-antenna (internal PCB) Maximum expected conducted power 2.51mW Operating Temperature -10O C to +50O C Operating humidity 10% to 90% non-condensed relative humidity Power supply requirements +6VDC -5% - +50% Open with Torx T20s screwdriver Label on the Host with following statements: Contains FCC ID: Y7V-681402004 Contains IC: 9514A-68102004
Title Installation of BLE Module 681402004 Category Installation of BLE Module Type Author Document number Revision Date Page (of) Susan Jansson 69 1402 012 8 20150302 13 (13) ASSA ABLOY HOSPITALTY AS. Overview functionality of the BLE Module When a BLE Module comes from the production, it will be in an ‘advertise’ mode that is always searching for another BLE device. In a hotel environment the BLE Module is set in ‘dormant’ mode and it will search for a BLE device when the Host System tells it to go out and search. When the BLE Module has found a BLE device and started the handshake, the communication between the BLE Module and the BLE device starts, they share information between them and the door opens, then the Host System tells the BLE Module to go to sleep. If the BLE Module doesn't find any device to do the handshake with, the Host System tells it to go down to sleep and stays in sleep until the Host System tells it to start searching for BLE devices.

Navigation menu